Devices USB 3.0 not being seen by 5.5 ESXI (free version)

Similar Questions

• Apple Mobile Device USB Driver has not passed Logo testing for compatibility with Windows XP, I ran the suggestion to "fix" 925196 that it still does not work. What can I do else?

  Bought the iPhone 3 g (not 4) trying to run the material but get the following error: Apple Mobile Device USB Driver no has not passed Windows Logo testing to verify compatibility with Windows XP continues the installation of this software may impair or destabilize the functioning of your system.

  Windows XP Service Pack 3 is running.

  I ran the 'Fix - It' 925196 solution, but the problem could not be solved. What is a malware problem?

  Hi deanie3,

  We will check if the following is useful.

  Method 1: Run the next Fixit and check the issue.

  Hardware devices do not work or are not detected in Windows

  Method 2: Follow the steps in the below article mentioned to see if it helps.

  You cannot install some programs or updates

• Device "USB" only is not supported after conversion

  * _Running vSphere + ESXi4 (paid and free) _ *.

  I have a XP system that has operated for some time, with 2 USB Dongles for software installed on VMWare Server authentication.

  Recently I found USB Net ShareStation IOGear solution for sharing USB devices over a local network, so I tried and managed to convert the virtual machine to free ESXi and successfully used the USB devices.  Perfect!

  However, I want to save this virtual machine using Veeam Backup, I need it in my firm paid ESXi so I converted again using the stand-alone converter, but I get the following message if poster every time I try to start it:

  Ons power failure

  vCenter could not find a suitable host to power on the virtual machine for the reasons listed below

  & lt; VM & gt;   & lt; NAME of HOST & gt;  Device 'USB' is not supported.  It is a virtual hardware version general limitation of the virtual machine on the selected host.

  If I change settings and delete or one of the USBs listed as not supported, I get again theerror:

  "USB" device is not supported

  and she does not.

  I only am not familiar with editing ini files so would appreciate pointers that would allow me to remove USB devices manually if this is what it takes so it wil boot.

  Thank you.

  You are welcome

  If you think that my answer was helpful, please give points.

• Device USB drivers do not install

  Whenever I try to install the drivers, I get an error saying its used by another process.
  [IMG] http://i47.tinypic.com/s6q8sy.jpg [line]

  [IMG] http://i48.tinypic.com/34y6xxe.jpg [line]

  [IMG] http://i47.tinypic.com/wcjvhu.jpg [line]

  The Device Manager shows "the drivers for this device are not installed [Code 28]"

  Earlier today, I tried one of the devices and the USB installer said it has been installed correctly, but then when I went into Device Manager it says the same error [Code 28]...

  Also, I noticed that when the files could not be installed, they have created a folder in the local user with what seems like characters generated randomly and inside each folder is a file (?) catalog of security with the relevant names that I try to install the devices.

  Here are some pictures of what I mean...

  [IMG] http://i46.tinypic.com/a442.jpg [line]

  [IMG] http://i48.tinypic.com/2nasdbq.jpg [line]

  [IMG] http://i50.tinypic.com/fcim8w.jpg [line]

  Appreciate anyone willing to help me with this!

  I guess my last suggestion really worked. Who were the last I can think.

  Now, the system cannot find the specified file. Perhaps, reference is made to the file INFCACHE.1. Fix INFCACHE.1 and SFC scan should have corrected it.

  Make sure that usb support is enabled in the bios.

  The devices were included under other devices, because they not have the drivers installed. The fix it is usually to remove the devices under him and search the hardware changes. You can try this.

  Try running the Fixit on the following link. This is for XP, but it should work for Vista because they have simillar Manager of devices. I saw that this posted on the Windows 7 forums.

  How to troubleshoot unknown devices listed in Device Manager in Windows XP
  http://support.Microsoft.com/kb/314464

  You can try to follow the methods listed in article.

  You can also try updating your chipset. Windows Update can do, I see that yours off.

• Device USB drivers were not installed-

  Hello

  I'm not able to install the USB driver (get error device not recognized... using Google USB Driver Manual same installation, helped... not even, I installed Google Android SDK, which has USB driver also)

  My Android tablet is slate DOMO X3G (4.0 ICS)... you can check the link for more details prodcut

  http://www.domoindia.com/index.php/2012-05-27-10-34-55/2012-05-27-10-16-49/Domo-slate-x3g.html

  my version of MS office is windows 7 SP1 (all the installed packeges updgrde)... I tried from another computer, also who was Windos XP SP2... facing the same issue...

  Appreciate any help to even...

  Thank you.

  Hello

  1 did you recent hardware or modifications to the software on the computer before this problem?
  2. What is the accurate and complete error message?

  Method 1:
  I suggest you run the hardware and devices Troubleshooter to check.

  Open the hardware and devices Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:
  If the problem persists I suggest to put the computer to boot and see if you can install the driver.

  By setting your boot system minimum state helps determine if third-party applications or startup items are causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: After the boot minimum troubleshooting step, follow step 7 in the link provided to return the computer to a Normal startup mode.

  Now try to install the USB driver and check if it helps.
  
  Method 3:
  If the problem is not resolved I suggest you to remove and replace all the USB controllers.

  To remove and reinstall all USB controllers, follow these steps:
  
  a. click Start, click run, type sysdm.cpl in the Open box and then click OK.
  b. click on the Hardware tab.
  c. click the Device Manager button.
  Bus USB d. Expand controllers.
  e. right-click every device under the USB Bus controllers node, and then click on uninstall to remove one at a time.
  f. restart the computer, and then reinstall the USB controllers. Restarting the computer should automatically install the drivers.
  g. plug in the removable USB storage deviceand then test to make sure that the problem is solved.

  For more information, please see the link.

  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

  If the problem persists I suggest you to contact the manufacturer for assistance.
  http://www.domosupport.com/index.php

   

  I hope this information helps!

• My usb port does not work. Device Manager says he has a "code 10".

  My dad recently bought a laptop on ebay. It's a HP Omnibook 900 with a 4 GB HD. The previous owner had improved from the original from Windows 98 to XP with SP3.

  It has a USB port in the back & it does not work!

  In fact it is not even appear in the Device Manager! I need to select 'Show hidden devices' to see same the USB hub root. The USB port has a yellow warning icon. In properties, it indicates the port is enabled but does not work because of a "Code 10".

  What the devil is a "code 10" & how in the heck to solve this problem, so that the USB works?

  The port is powered. When I connect devices usb load they turn on & load, but, of course, are not displayed on the computer. My best theory is that the port can be usb 1.0 but the software is intended for usb 2.0 and what could be the cause of the problem. That's just guessing on my part because I do not know with certainty if the usb is 1.0 or 2.0.

  It is especialy boring being the only external devices can I plug a CD player (unwritten) & a floppy drive. It would make my life much more pleasant if I could run software, backup & file transfer, etc. with a usb drive instead! It could even than the laptop quite useful to be worth the bucks thirties, my father paid for it!

  Help, please. Thank you.

  Hi SnarFoo,

  Method1

  The Code 10 error code is generated when Device Manager it has not enough information or error that has spread upward through the device drivers is not recognised by the Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  See the article and check if that helps.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  Method 2

  If the previous step fails, then remove and reinstall all USB controllers on the computer and check if that helps.

  To remove and reinstall all USB controllers, follow these steps:

  (a) click Start, click run, type sysdm.cpl in the Open box, and then click OK.

  (b) click on the hardware tab.

  (c) click the Device Manager button.

  (d) expand Bus USB controllers.

  (e) right click on each device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  (f) restart the computer and reinstall the USB controllers.

  (g) connect the removable USB storage device and perform a test to ensure that the problem is solved.

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

• Removed USB controllers: can not return - "this device cannot find enough free resources that it can use. (Code 12)

  Original title: removed USB controllers: can not return

  Hello

  So today I tried to connect to a printer, and it wouldn't work (separate the issue, I don't want to worry about that now)

  I've seen several messages saying: you need to uninstall the USB controllers in Device Manager and then restart your PC. The pilots would then automatically reinstalled.

  It didn't happen, and now my Dell touch screen does not work. I can miss several other USB controllers too, I uninstalled about 3 of them, but I don't know whether or not it has been reinstalled.

  I currently have:

  -Hub USB generic

  -Enhanced host controller USB Intel (R) 8 series #1-9C 26

  -USB root hub

  -Host controller compatible xHCI USB

  Note that the last of them was a symbol of error on it and reads as follows:

  "This device cannot find enough free resources that it can use. (Code 12)

  If you want to use this device, you will need to disable one of the other devices on this system. »

  Can someone please tell me how much USB controllers I should have and how to save them?

  Thank you very much

  Hi Shalini.

  Thanks for the reply, but if you read through the posts on this thread, I think you will find that it has already been suggested that I do these two things - what I've done many times without result.

  Fortunately, I managed to fix it myself.

  To satisfy your curiosity and help someone else who could see this thread with a similar problem, here are the steps I took finally solve the problem:

  ______________________________________________

  I was always convinced that the problem is basically with the xHCI USB controller that I saw always reported as not working not properly in the device (Code 12) Manager. With this in mind, I set out to see if I could determine what the device was supposed to be in conflict with. I ran msinfo32 and began to examine the conflicts/sharing section. After a while, I decided I could not see anything obviously problematic or direct me to the controller xHCI, so I gave up on that front.

  Well, if I couldn't fix the problem with the current installation, maybe that I could find another way to install the xHCI USB controller that could circumvent the flaw that seems to be caused when windows reinstalls automatically it when restarting after the abduction. So I started trying to learn more about this "xHCI USB controller" - since Googling this term has given no end of problems not related.

  In Device Manager, I found a way to isolate the details of this driver in device (somewhere under the properties I believe) Manager. This has created a custom device showing in view only a select few connects the Manager. I have spent some time in the analysis of these and found the time during which the camera has stopped working properly. Suddenly a pattern emerges. Over and over again, see you the following series of when I was hoping that allowing windows to reinstall automatically the driver would to fix:
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been removed

  [Rebooted PC]

  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 has been configured
  • Device PCI VEN_8086 & DEV_9C31 & SUBSYS_05F91028 & REV_04\3 & 11583659 & 0 & A0 had a problem starting.

  Under each newspaper was referring to a driver name, I didn't already had access to: driver name: usbxhci.inf

  Now I got some new information about the xHCI USB controller, I took to Google. After much research (and not find something relevant), I found 2 obscure references to the driver who seemed at least somewhat relevant.
  The first reference has been a post on the forum where someone's USB ports stopped working. very similar problem to mine! There is little of any particular use in the nets, with the exception of the reference to a couple of windows updates: KB 2823516 or KB2822241

  It is not clear exactly what usbxhci.inf capacity was tied to these updates, but I made a note of them and moved.

  Another article contained no mention of specific ports USB not working does not and was centered around a different problem entirely. However, he has mentioned an another windows update: KB2919355-x 64.msu

  This one (as I remember) was clearer on the relationship between the update and changes to the usbxhci.inf file.

  Now, I had three updates which could make changes to usbxhci.inf at one point. With their name on a piece of paper, I started looking through my updates installed to see which ones I had installed. I soon discovered that Ko 2823516 or KB2822241 were not present on my PC, which saved the penalty to guess who would be the right to uninstall first.

  KB2919355 has been installed, and I made the decision to uninstall it, because as far as I knew, this update changed something in usbxhci.inf. After the initial uninstall was completed, but before the mandatory reboot for changes to take effect, I went into Device Manager and removed the xHCI USB... because I was afraid that if the new, "defective" was always present during the reinstallation of the update, it doesn't change anything.

  The device is removed once more, I rebooted the system. He drives for a considerable period, uninstall the update and then seems to have some sort of hitch; declare something in the sense of "we could not complete the operation. Changes to undo. " He stayed like that for a while before the system became operational again and began to "prepare windows. Once it was over, I discovered that my touchscreen and USB ports worked very well.

  Investigation later showed that the compatible USB xHCI host controller was is no longer marked with warnings. In addition, a series of USB controllers appeared that had not been there when the xHCI device was defective. I was also pleased to note that the update of windows for KB2919355 had already been reinstalled without messing up anything.

  _________________________________________________

• Why my photos are not being updated on all my devices which or login to iCloud?

  Why my photos are not being updated on my iPad if all my devices are signed in iCloud?

  On your iPad, tap settings > iCloud. Make sure the Photo is on.

  Additionally, make sure that your iPad uses the same account as your other devices iCloud to synchronize data.

• Satellite Pro L10 - USB port will not recognize devices

  Hello

  I got a L10 for 18 months. Under the guarantee, I got a replacement motherboard mounted. Everything has been ok so far. A USB port will not recognize devices, a port is ok, but randomly turns off a device attached to it and comes up with the message "USB device not recognized". The third port is ok all the time.

  Any solutions or suggestions?

  Post edited by: caddy

  I guess there is not enough power on the USB ports and external devices may not work correctly. It is not easy to say why this happens, but there may be a problem of welding.

  I recommend you contact the service again as soon as possible.

• Device USB not recognized - device connected USB has malfunctioned and Windows does not recognize it

  I have a HP Pavilion dv4 laptop running Windows 7 Home Edition Premium and the USB ports worked well for a HP deskjet printer and an older Casio digital camera. Then one day, the laptop decided not to recognize the Casio digital camera and gave the error message "USB device not recognized" and also indicated that the device connected to the computer has malfunctioned. This prompted me to buy a new digital camera Canon. Well, a new camera has not fixed the problem. Now, anything that is connected to one of the 2 ports USB will not be recognized by my laptop. Help!  I am at a loss to understand this.  I tried using Microsoft suggested below:

  Suggestion 1: the problem with USB devices, uninstall and reinstall all USB controllers. This allows controllers to recover the port USB of his condition does not respond.
  USB controllers represent the USB ports in Device Manager.

  a. Click Start, type Manager of devices in the search box of start and press ENTER.
  b. expand Bus USB controllers.
  Note: you may scroll through the list to find this point.
  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.
  d. Repeat steps above for each controller USB is listed under Bus USB controllers.
  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.
  f. check the USB device to see if it works.

  This has not fixed the problem.  Then the Device Manager, I tried to update the drivers on all the USB controllers and root hubs. While some may have received software updates downloaded, it still has not corrected the problem of unrecognized USB device after the computer is restarted.  I hope that someone knows the solution to this situation and can pass it on to me. Thanks for reading and any help display.

  Read previous messages revealed the solution for USB devices not recognized on my HP Pavilion as well as several other laptop models.  Shut down the computer and remove the battery and wait for about 15 minutes. Reinstall the battery and restart the computer.  USB ports are working to download pictures from my digital camera from Canon and charging a cell phone, etc...   I hope it helps others with this problem!

• any USB device USB not Republic United Nations notes senza

  Without some special USB device USB no Republic - Cosa fare UN notes? Grazie leopoldo Rogante

  Hello

  This is an English language Forum.

  Please go to

  http://answers.Microsoft.com/en-us

  to select your language from this link English 

  Don

  Questo e UN forum in lingua inglese.

  If get di andare

  http://answers.Microsoft.com/en-us

  by rates the lingua da questo link English 

• device - device USB not recognized

  I have an external hard drive, but my laptop does not recognize it always. the message that appears reads as follows:

  One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it

  Usually when I start my laptop the morning he is there for me to use, but every time I have to remove and attach it again, it is not recongised.

  Hello

  Follow the steps above and if that doesn't help not follow them steps below to uninstall and reinstall the USB controllers.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If the control panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  (d) check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (e) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  (f) then restart your computer and Windows 7 will automatically reinstall all USB controllers.

• The Epson Workforce 600 is connected via a usb cable, the other is a wireless network. I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it does not list

  I have two printers installed on my laptop, only appears.  The Epson Workforce 600 is connected via a usb cable, the other is a wireless network.  I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it is not the list when I go to print something.  When I select "Find a printer", it gives me a list of computer icons.

  Hello

  Check with Epson support, their documentatiion online and drivers. As it's Epson OEM
  responsible for the proper functioning of the printer and their drivers provided.

  Good luck, you need to update or reinstall the latest driver.

  Epson - Support us.
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?BV_UseBVCookie=Yes

  Epson - support from Europe
  http://www.Epson.co.UK/support

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Device USB error: USB device not recognized

  For a week to 10 days I could not connect my USB drive to the USB port. Also my keyboard and mouse stopped working because I was using a USB hub. It must have been a few Windows Vista update recently which caused this problem with USB devices. It does not recognize the USB devices. I can use the USB device on my laptop mini where I have Windows 7.

  Microsoft is going to solve the problem in Windows Vista. There should be no reason that we cannot use USB devices and before 10 days ago, it was not a problem.

  Thank you for your help.

  Hi NRuss,

  1. have you checked if the devices are getting detected in Device Manager?

  Step 1: Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Step 2: Uninstall all USB device manager entries

  a. Click Start and typedevmgmt.msc and then click OK. Device Manager opens.

  b. expand Bus USB controllers.

  Note: You will need to scroll down to find this point.

  c. the first USB controller under Bus USB controllers right click and then click on uninstall to remove it.

  d. Repeat step 4 for each USB controller is listed under Bus USB controllers.

  e. restart the computer. After the computer starts, Windows will automatically check for changes on the hardware and reinstall all USB controllers that you uninstalled.

  f. check the USB device to see if it works

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Vista - usb ports are not recognized unknown device

  Vista - usb ports are not recognized unknown device. any usb device it appears unknown. all worked a few days hardly, but after that I connected my Kodak camera - which does not, now, nothing works. Any help would be appreciated.

  Hello

  Thank you for using the Microsoft Windows Vista Forums.

  Follow the instructions below that may help you resolve the issue.

  Method 1:

  Try to connect USB devices to a different USB port and check if you are able to access.

  Method 2:

  Click on the link below to run Fix it which will help you to solve the problem.

  Tips for solving problems of USB devices

  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx

  Click on the link below and install the update.

  Rollup cumulative update for USB in Windows Vista Basic components

  http://support.Microsoft.com/kb/941600

  Try to connect the camcorder to the other USB port and on the other computer and see if the problem is resolved.

  Method 3:

  Let us try to disable the Antivirus security software and check the number.

  Re-enable the security software after checking the issue.

  You can also try disabling the firewall and check the issue.

  Re-enable the firewall after checking the issue.

  Method 4:

  A clean boot helps eliminate software conflicts.  Let us check if software is causing the problem by following the clean boot procedure.

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot

  Step 2: Enable half the services

  Step 3: Determine whether the problem returns

  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns

  Step 6: Resolve the problem

  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista

  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to the Normal mode.

  Uninstall or update the program that is causing the problem.

  Check whether the problem is resolved.

  You can also check out the link below.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/6be4581d-8fbd-407F-815E-b475c35ca586

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP