DHCP for several local area networks VIRTUAL via SG200 - 50 p

Similar Questions

• question of vSwitch transmission of local area networks VIRTUAL VMWare ESXi, Vsphere 5.0 5.0

  Having little experience VMware, I entrust the task to try to see why one of our VLAN does not work on one of our servers ESXi 5.0. I will try to be as descriptive as possible.

  The issue began just after works well for months, when it started for starting and running config had not been updated for several weeks on the router and switch.

  Our server has 4 0 1 2 3 physical NICS

  0 and 1 are associated together on VLAN1 and are also used for the management network

  Map NETWORK 2 is used for 111 VLAN (network connect our wireless users to so that they cannot interact with VLAN1)

  3 NIC is connected to the VLAN 66 (a network for video and deployment services)

  These 4 physical network adapters is connected to three different vswitches as follows (I'm not the one who created these so don't ask why they are as they are)

  a vmnic0 and vmnic1 vSwitch0

  vSwitch1 has vmnic3

  vSwitch2 has vmnic2

  All these ports are physically connected to a Dell PowerConnect 5548 switch

  vmnic0 to:

  interface gigabitethernet1/0/24

  Description "VM Server 1.

  switchport mode general

  switchport general allowed vlan add 111 tag

  VLAN allowed switchport General add 1 unidentified

  VLAN banned general switchport add 5,66,98

  vmnic1 to:

  interface gigabitethernet1/0/17

  Description "VM Server 2."

  switchport mode general

  switchport general allowed vlan add 111 tag

  VLAN allowed switchport General add 1 unidentified

  VLAN banned general switchport add 5,66,98

  vmnic2 to:

  interface gigabitethernet1/0/6

  Description «VM Server 3»

  switchport general allowed vlan add 111 tag

  VLAN allowed switchport General add 1 unidentified

  VLAN banned general switchport add 5,66,98

  switchport access vlan 111 (tried several different configurations on this port that Trunk including 1 unmarked and 111 the tag as VLAN 1 and 111 come through the router on the same port. Also just a base switchport mode access vlan 111)

  vmnic3 to:

  interface gigabitethernet1/0/43

  Description "VM Server 4.

  switchport access vlan 66

  If I plug a laptop computer into im int 1/0/6 I get an IP address from the DHCP server, and you can get online. When I go into the properties vSwitch2 and go to VMKernel and try to set it to automatically get an IP address, I get a 169.254*. * address. There is no connection if I statically set the address of one knowledge is available yet. I'll add more information later if needed, I have a meeting in which concerns another project. Anyone who can help, thanks in advance. If you need specific information, I will answer as soon as POSSIBLE.

  On the configuration under maps page network vmnic2 has no observed IP address ranges and I do not know how to change the nic to perhaps add the addresses

  I would try to eliminate the physical NETWORK adapter on the host being the issue. Silly question, but is there a link light? Drop a sniffer out there and see if there is no traffic passing if trying a different physical nic does not help.

• I'm not able to open the properties and the State in Local (or all network devices) network. Actually I am not able to connect to the local area network connection in network and sharing Center.

  Connection to the local network - properties dialog box

  Hi, I'm not able to open the properties and the State in Local (or all network devices) network. Actually I am not able to connect to the local area network connection in network and sharing Center. But I can't access the Internet. My OS is Windows 7

  Hello Rajaneer,

  Is the computer that you are using a personal computer or a work computer?
  You will need to re - install your network card drivers like something was damaged and it prevents you to access the property:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• How to allow access to a local area network behind the cisco vpn client

  Hi, my question is about how to allow access to a local area network behind the cisco vpn client

  With the help of:

  • Cisco 5500 Series Adaptive Security Appliance (ASA) that is running version 8.2 software
  • Cisco VPN Client version 5.0 software

  Cisco VPN client allows to inject a local routes in the routing table Cisco ASA?

  Thank you.

  Hi Vladimir,.

  Unfortunately this is not a supported feature if you connect through the VPN Client. With VPN Client, that the VPN Client can access the VPN Client LAN host/local machine, not host from the local network to business as customer VPN is not designed for access from the local company network, but to the local corporate network.

  If you want to access from your local business to your LAN network, you need to configure LAN-to-LAN tunnel.

• No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Original title: no local network connection

  No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Hi H.mustafaakyurek,

  ·         What operating system is installed on your computer?

  You can view the following items on the creation of a network connection:

  Setting up a network home

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

   

  Start here to set up a home network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

   

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Also see the following articles on the connection of an Internet connection:

  What do I need to connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/what-do-I-need-to-connect-to-the-Internet

   

  Allows to connect to the Internet mobile broadband

  http://Windows.Microsoft.com/en-us/Windows7/use-mobile-broadband-to-connect-to-the-Internet

  Hope this information helps.

• What happens if I uncheck all the properties of LAN (Local Area Network)?

  What happens if I uncheck all the properties of LAN (Local Area Network)? My machine OS is Windows XP Home Edition / 2002 Version / SP3 and I have a wireless connection. My connection to the LAN is disabled, currently, I don't have the desire to create a network, and I will in the future.

  Hi Bobby Collas,.

  There is no problem, when you turn off all the options in the properties of the local area network (LAN).

  You will not be able to connect to the Internet or use the connection to the Local network.

• Satelite C50 - B cannot connect to wireless local area network

  My brand new straight out of the box Satelite C50 - B cannot connect to my wireless network, when you are running Windows 8.1.

  When you run the wizard for the first time user, it was unable to connect to my network to register. And I have been unable to connect after starting the OS, even if my thread was visible and the signal strength would be strong. I entered the security network key, but the message came back "unable to connect to this network.

  However, when I started on a USB key to run Linux Mint 17.1, it took less than 5 seconds to connect to my wireless network. If the Toshiba hardware work properly, as also my wireless LAN.

  If I plug in a network cable, same Windows connects to my network and Internet.

  However, given that the C50 - B satellite comes with Windows 8.1 both of wireless capabilities, I was hoping someone here might be able to help me get a wireless connection in Windows.

  It's really strange. I have S50 - B and WLAN works properly. I used my laptop connected to several different networks and everything was OK.
  You can try to test with different wireless LANs?
  Have you checked all the WLAN settings?
  Try restarting your router.

  I mean if your laptop can detect WLAN, this means that the hardware is enabled and working properly. There must be a problem with the WLAN settings.

  Also check the advanced power settings, and then set it to maximum power WLAN.

• Extreme slowness of local area network and Time Capsule wireless speeds

  I have a time Capsule Airport Extreme 3 G with firmware version 7.7.3 I use for lan connections / wireless and backup of all apple devices that do not use the cloud. For the last month or so sometimes I ridiculously slow speed issues that cannot be remedied with any one of them that I have tried. Speed control on my i mac or wireless on any device in any location see accelerates it half of what I pay for. If I shoot a speed control to the back of the modem, everything is ok. If I shoot a speed check in a port on my machine Net Pro FVS318G safe with Airport extreme disconnected speeds are fine. But when the capsule is used the speed is slow. This happens not all the time. In fact this am that everything was fine, she just started about an hour or two there once again. And it normally clears up in a few hours on its own. It is like someone is inside my computer slows down I can't even do a backup on my i-phone when this happens.   I bought the thinking net machine that triple nat could help I'm not using the vpn option. I'm lost and open for suggestions?

  My mac i run El Cap v 10.11.4.

  Att Uverse 18 m 1 m

  Time capsule two years old.

  Check the speed of 1-6 m down issue when happening, 17-18 when well. done before also.

  Can you please describe your network topology?

• Satellite A100 - 02 M: cannot open the local area network to share files and printer - LAN Unplugged

  I have an office of another manufacturer which was connected by a wireless network via a Belkin router for a laptop another manufacturers - both running XP.

  I have now replaced the other laptop with a laptop Toshiba Satellite A100 - 02 M under Vista Home Premium. While I can still access the Internet from both machines, I can't open the LAN to share files and printers. The laptop shows 'LAN Unplugged' all the time. Any ideas would be accepted with gratitude.

  Ray Freeman

  Hello

  I have no general solution, but I'll try to give some advice solution;
  If you want to connect laptop with LAN cable both please make sure that you use a crossover ethernet cable.
  In addition, check if the network card is properly recognized in Device Manager.

  You could try updating the LAN driver and remove the NIC in Device Manager to update the installed driver.
  After restarting again the operating system should recognize the new (Lan) device and should install it automatically.

  I also studied a bit in this forum and found a similar thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=14852&MessageID=54037

  Check the proposals contained in this message.

  By the way; Microsoft provides a very useful page on Vista and how to configure the network, the file and printer sharing and troubleshooting
  http://windowshelp.Microsoft.com/Windows/en-us/networking.mspx

• I don't see local area network. Win 7, IE 10. How can I do so?

  I do not see local networks with my win 7-64 bit, that is to say 10.  How can I do so?

  Hi David,

  Please answer a few questions to refine the question.

  1. When you say LAN. you earn to the available network connections?

  2. are you using wired or Wi - Fi?

  3. are you able to access the network with other browsers?

  Try to run the network troubleshooter and see if that fixes the problem:

  Check out this link to do the same thing:

  Network convenience stores

  http://Windows.Microsoft.com/en-us/Windows7/open-networking-troubleshooters

  Provide more information so that we can help you.

• Satellite Pro L40 PSL43E: Unable to connect to wireless local area network

  Hello to everyone who reads,

  I've had this laptop for about 12 months and a few days ago while trying to connect to the internet, she advised that I was not connected to my router.

  I have another laptop, it connects well with wireless and it connects fine using the ethernet cable but wireless!
  Especially, when I switch the radio power on/off using the small switch on the front the same symbol rises (the cell phone, red circle with a red slash through it, then the sign of the internet!)

  I tried the update of the driver for the Atheros AR5007EG Wireless Network wireless adapt and not much happened!

  I'm not in portable computers in a big way so any advise given better would become simple?
  I saw some stuff about the removal of the cards and other things? but I don't know where to start!

  Is it a common thing with these laptops?
  Need help please, I desperately need my laptop wireless.

  Thanks a lot to all in advance

  Paul

  Hello Paul

  Make sure that the wireless network adapter is correctly enabled.
  After putting using WLAN switch using FN + F8 key combination and make sure the wireless network adapter is enabled.

• Satellite L300-10 q - imposible to connect to wireless local area network

  Bought a Satellite L-300-10 q and imposible to connect to the wireless LAN.

  A message appears when you try to install the WIFI network:

  "This WLAN device is disabled. Please activate the device. »

  What can I do? Tried everything.

  The message is clear to me;
  It is said that the Wlan adapter is not enabled.

  Activate the WLan WLan switch on the switch position. The LED must be on.
  Press FN + F8 key until the WiFi network will be chosen.

  This should help to enable the WLan feature

• Need to restrict users on a local area network to play video files from a share

  origin: data sharing and visualization.

  I've shared videos accessible via LAN,

  I want my LAN users simply copy,
  do not play as it keeps my server busy.
  I wish that they just copy it... I told them repeatedly to copy, but they play directly that causes the server will slowly...
   
  Is there a policy in windows xp sp3? Please, thank you.

  Hello

  The question you posted would be better suited in the Technet Forums. I would recommend posting your query in the Forum Technet site:

  social. TechNet.microsoft.com/Forums/en-US/category/windowsxpitpro

  
  

• Tab shares missing Local Area Connection

  Hello friends!

  Bad, I need your help... I wanted to share my internet to my laptop for my android phone, but I can't find the tab sharing for my local area connection properties. How can I fix?

  It looks like this on my laptop (sample image ONLY not mine)

  

  Your help will be very appreciated! Thank you in advance! :)

  Hello

  How did the laptop connected to the internet? Is it cable or wireless internet connection?

  The sharing tab is not available if you have only a WLAN card.

  If the Android and Windows 7 have a Wi - Fi connection watch connectivity or Virtual Router to turn the Win 7 machine into a hotspot Wi - Fi.

  I suggest you to refer to the links and check if it helps:

  http://Windows.Microsoft.com/en-in/Windows7/set-up-a-shared-Internet-connection-using-ICS-Internet-connection-sharing

  http://Windows.Microsoft.com/en-in/Windows7/what-are-the-different-Internet-connection-methods

  http://Windows.Microsoft.com/en-in/Windows7/unleash-the-power-of-your-laptop

  Please post with the information needed to get help.

• Rules of research and the local area

  Hi I am a newbie in VC and follow the deployment guide and manage to make the following call flow design and be able to make a video call to outgoing [email protected] / * /

  endpoint > CUCM > VCS - C > VCS-E

  I have two questions.

  (1) when I try to create the rule to search for local area, I don't see a local area instead of target area. When I go to the area and create the new zone, I don't know what to choose for the local area.

  (2) I managed to call traversal for only cisco.com field because I create the rule search for cisco.com with the following parameter.

  Any

  Any

  NO.

  Alias matching

  Regex

  (. *) @cisco.com(.*)

  Replace

  Continue

  Crossing area

  But when I create the same rule to search for another domain, it does not work. I like to do rule the research to be able to call all the other external domain.

  Please notify and appreciated any suggestion.

  You have Expressway series not VCS.  VCS has local areas because VCS can make the device records, while the highway is not because he spends at CUCM, so there not need a local zone endpoint to register for.

  Deployment Guide of what you're talking about, it's probably for VCS?  You should go the the way Express base Configuration Deployment Guide X8.5.