DHCP installed on RV042

We have a network with a router RV042 set. Router is connected to the Cox Cable and DSL ATT. Currently have 20 computers hooked up to the router all using static IP addresses. The installation program is in place for more than 7 years. I want to set up a wireless network access point. The problem is, I can't get DHCP to work right even WITHOUT the wireless access Point. I took one of the computers that works very well with a static IP address and this changed to be DHCP, I activated the DHCP on the router and the game of and through settings for the assignment of intellectual property. The computer will connect and obtain an IP address and it allows me to see all the INTERNAL servers on the network, but goes to the Internet of TRUE FEUILLETEE. I usually have to refresh them 5 or 6 times to get a web page and sometimes even don't work. If I get a next page it is about 10% chance that it will bring up a subpage of the page without doing a refresh 5 or 6 times. It's like he can't keep the connection to the Internet. I noticed something different in the manual of the RV042 which is different from all other Linksys routers, I worked with. It is said that when you enable the DHCP on the router, you can ensure that all THE computers hooked to it are set for DHCP. All other routers I've worked with that do NOT use that Word. Am I missing some setting or is it a binding thing where you're ALL static or DHCP ALL? Any direction would be greatly appreciated.

Charles,

Your presumption is correct about binding protocol.

  1. Have you tried Smart Backup link instead of the load balance to see if you get the same results?
  2. Also, have you tried setting the router to force a static IP based on MAC address? DNS (-> Setup)
  3. Make DNS servers in the game of router, static DNS servers on your PC?

Tags: Cisco Support

Similar Questions

  • RV042 150 DHCP Option

    Hi people

    I have a RV042 VPN router with the latest firmware v4.2.1.02.

    This router is connected to the main site through a VPN Tunnel.

    Now, I want to configure a DHCP Option if I can put an IP phone

    behind the RV042. The IP phone should receive an IP by DHCP

    the RV042 and of course, the IP address of the Director with the

    Option of 150.

    I can configure DHCP and it works fine but I can't find where I

    or can configure Option 150.

    Does anyone know ho it works?

    Thank you for your help...

    Kind regards

    Pascal

    Unfortunately RV042 isn't compatible DHCP Option 150.

  • The RV042 can access Internet

    I am new to implement VPN service.  I want to do this is to install a RV042 or RV082 (for extra speed) and configure it to allow me to access the Internet (from home port) by the VPN from anywhere so that on the road and using my laptop.  My questions are: is it possible?  If so, what needs to be done in the configuration to allow access from the front door to the Internet? I can't find any reference in the Cicso documents, but somewhere I have seen that it is possible.  I do not how to access anything on the local network.  As I would use the same Internet connection to the VPN and access out - how this effect would speed?  I intend to use fast VPN as the client and have not yet touched the issue of the client.  Pointers would be greatly appreciated.

    Richard,

    RV0XX routers do support a customer to the gateway via PPTP or IPsec solution. Each connection will provide local access to the network to which you are connecting.

    However, if your goal is to connect to a remote router can use the internet as if you were local to the router. This is not going to work.

    Example:

    Robert - 75.75.75.75 - VPN TUNNEL - RV0XX 76.76.76.76---> INTERNET

    If you connect to the router RV0XX by using a PPTP or QVPN connection, your internet connection will continue to use your IP to 75.75.75.75. You will not be able to have your external IP address showing as 76.76.76.76.  However, local access to the RV0XX to the router is authorized.

    If you are looking to have VPN to access a router and your internet see intellectual property as if you use the remote router locally, you need a tunnel full VPN solution.  The RV220W router will support this with 5 spaces (free) SSL vpn.

  • RV042 firewall & Port forwarding

    I install a RV042 on a SBS client network.  In the configuration, I noticed that there is a place for port forwarding where I guess I could open the smtp, http, https ports...

    But there is also access rules in the firewall section that seem to be the same, except that you can program them.

    This is, do I have to set up the two, or if only one of them, which one?

    Thanks in advance for the advice.

    Bob Showalter, Packer International

    Bob,

    You must configure the port forwarding, except if you want to specify a source and a destination that the package is granted or denied; you would then both.

    hope this helps,

    Jasbryan

  • Private network with Internet access

    Hello

    Using WS 9. Building a 'private' isolated network who always has Internet access for testing purposes? I built a virtual machine that has AD, DNS and DHCP installed. Ask yourself if it's feasible to isolate this virtual machine from the corporate LAN, but allow it to have access to the Internet to d/load patches/security fixes?

    I created "the" private network as follows (VMnet2):

    vmedi.JPG

    Thank you

    BRITISH COLUMBIA

    Host-only, it's just that and does not communicate beyond the host.  You could add a connected by a bridge or a NAT Network Adapter to the Virtual Machine and connect it to your updates and unplug when done.

  • How to install Photosmart B109n-z on a DHCP network wireless

    I'm trying to install a HP Photosmart B109n-z on a wireless network.

    There is no DHCP server on the network.

    I can install and print using a USB cable.

    When I try to reconfigure the display of the USB wireless I get a message that says printer

    use the IP 169.254.95.189 which is not compatible with the address IP of the PC 10.1.9.1.

    HP documentation * recommends * using a DHCP server. So I guess it's * possible * for

    do without. But I have found no instruction to do so.

    There is a related announcement with the following title:

    > Resolved: Photosmart B109n-z - setting a static IP address on the printer on an active DHCP server router
    > 04/01/2010-11:24

    That the display shows:

    > Type the IP address in a browser.  You will see the internal settings of the printer.

    But when I go to http://169.254.95.189 I have a connection delay.

    169.254.95.189 ping succeeds. When I run a tool of command ' arp - a', I can see the printer.

    The above has been done using a Windows Vista-based computer. To get a second opinion, I started a Linux machine

    and did a ping 169.254.95.189. Which failed. Then I did a

    > Add a route - host 169.254.95.189 gw 10.1.6.1

    10.1.6.1 where is my wireless router. Then ping succeeds but looking upward of http://169.254.95.189

    still gives a timeout.

    So my main question is: how to set up printing on a DHCP-less network wireless.

    And a second question: the printer is supposed to listen on TCP port 80 (http) or a magic

    necessary to turn on.

    IP STATIC ASSIGNMENT HOWTO FOR HP PHOTOSMART B109n-z

    The following instructions allow to assign a static IP address on an HP Photosmart
    Printer B109n-z without using a DHCP server, and without using a router. The
    statements can also be used for other types of printer setup.

    Necessary equipment:
    -A HP Photosmart B109n-z printer
    -A computer with a wireless network card

    Laptops usually have a wireless network card. Stationary computers
    usually not.

    1 BACKGROUND

    B109n-z has four ways to communicate with others:
    (1) there are buttons and a small screen on his forehead.
    (2) it can print and scan pages
    (3) there is a USB connection
    (4) it has wireless capabilities.

    We will use (1), (2) and (4) to set a static IP address.

    2 BUTTONS AND DISPLAY

    If you're reading this, chances are that you tried to install the B109n-z and that
    the installation failed. The installation may have left the B109n-z partially
    set up, so the first step is to bring the B109n-z to its initial settings.

    On the front of the B109n-z there is a small screen. To the left of the
    It is a column of three buttons. To the right of the screen, it
    is a column in addition to three buttons.

    In fact, the buttons are just touching sensitive areas next to the screen. Each
    button's background light that the printer can turn on and off. During the
    light behind a button is disabled, the button is invisible.

    The buttons in the left column are labeled with an arrow to the rear, an 'X' and
    a symbol "OK." The buttons on the right hand column are all labelled with dashes.
    To the market, the screen displays something like this:
    Scan
    Photo
    Copy

    The background light of all three buttons in the right-hand column are on. Now press
    the button to the right of "Scan", i.e. the highest button in the right column.
    Now, the screen displays something like this:
    Wireless menu
    The scan to PC
    Scan to memory card

    Now, press the button to the left of the menu "wireless" to get this:
    Turn off wireless
    Wireless configuration
    WPS

    This option enables the radio into the printer. The screen comes down to this:
    Turn off wireless
    Wireless configuration
    WPS

    Now press the button next to "Wireless Setup", then press
    the lower right button until something like 'restore wireless settings' is
    selected. Then press 'OK' (the button at the bottom left) and answer 'Yes' to 'are '.
    "ensure that" issues. Now, it comes down to this:
    Enable wireless
    Wireless configuration
    WPS

    Finally, if the wireless radio is turned off, turn on the radio wireless with the help of the
    button at the top right.

    Now, the radio of the printer is on, the printer has an IP address of 0.0.0.0, as well as the
    printer Wireless Announces that he runs a computer-to-computer wireless
    (ad hoc) network without security. The SSID of the network is "hpsetup".

    3. CONNECT TO THE PRINTER, STEP 1

    Now, you need a computer with a wireless interface card. Ensure that the computer is
    on. If the computer runs windows, ask for a list of available wireless
    networks. If she runs something else, do something similar.

    In the list of available wireless networks, you should find a named
    "hpsetup". Connect you to it. Ignore the warning that the network "hpsetup" is
    situation of insecurity.

    If there is more than one network named "hpsetup", one of them will be your
    printer and the others can be printers in your neighborhood. Those of other
    could also be the work of airborne viruses that have infected your neighbors
    computer.

    4. PRINTING CONFIGURATION

    If you followed the instructions above, the display will show this:
    Enable wireless
    Wireless configuration
    WPS

    Select "Wireless configuration", let "print the network configuration page.
    selected, then press OK. The printer now prints a page that says things like
    this:
    IP address: 169.254.95.189
    Subnet mask: 255.255.0.0

    5. CONNECTION TO THE PRINTER, STEP 2

    Now assign the same subnet mask and IP address similar to laptop you such that:
    IP address: 169.254.95.190
    Subnet mask: 255.255.0.0

    The operation of bitwise AND of IP address and subnet mask of the printer must be equal to the operator AND the IP address and mask subnet of the laptop.

    You need to know how to set the IP address and mask of the subnet on your laptop. If you have struggling to survive on a network without a DHCP server. But if you need an update: go to the 'properties' of the network connection and choose the TCP/IP settings.

    Now open a web browser such as Internet Explorer, Firefox or whatever and look for http://169.254.95.189

    Now you can set up the printer using the web browser as an interface. To set a static IP address, do the following for example:

    -Click on the Networking tab
    -Choose wireless along the left side
    -Choose the IPv4 tab
    -Click on the manual button IP
    -Enter the desired IP address
    -Enter your subnet mask (255.255.255.0 unless you know otherwise)
    -Optionally enter an IP of the appropriate gateway (see INFRASTRUCTURE NETWORK below)
    -DNS leave empty
    -Click 'apply '.

    When you click 'Apply' you of course lose the connection to the printer.

    Now close the web browser, set IP address and the subnet of the laptop to what it was and try to connect to the printer using any IP you assigned.

    6. CHANGE NETWORK INFRASTRUCTURE

    If you want to change an ad hoc connection to aid in making a
    network infrastructure, you need a wireless router. Ensure that the
    The gateway of the printer IP is the IP address of the router in Section 5 above.

    You can now install the software on the CD supplied with the printer. If you have previously installed the printer simply to connect a USB printer,
    the USB cable, insert the CD and reconfigure to wireless technology.

    During the reconfiguration, you will be asked which network to use. Select your
    own network (that of the router to use). Do not select the
    ad - hoc hpsetup network.

  • Need a how to: second RV042 DHCP

    All, Hy

    I have a CISCO RV042 networked with 2 subnets 192.168.1.x and 192.168.2.x and I want several DHCP on both subnets. How can I do?

    If I use a second router to the second subnet (192.168.2.x) to use DHCP. Bandwidth management will not work? I need port VLAN?

    The network is like this:

    The RV042 is the main router through it we internet access, she also suplies DHCP 192.168.1.x, I activated several 192.168.2.x subnet.

    The reason I want 2 subnets is beacause I have 2 access points for wireless clients and I want to use the frequency control over WAN with RV042 bandwidth management give too many wired customers more bandwidth than wireless clients.

    I know that RV042 does not multiple dhcp as RV180, but I need dual WAN.

    Thank you

    Wrong forum, post in the "Small Business routers". You can move your ad with the Actions Panel on the right.

  • install 10g release 2 standard edition. Address DHCP problem

    I get a warning "installed detected that a primary IP address of the system is assigned DHCP." I have to configure the microsoft loop back adapter for the main card in the system. I don't know what to do.

    Hello

    The main map is determined by the order in which you installed adapters: this is the last card is installed. If you install additional network cards after installing the loopback adapter, you need to uninstall the loopback adapter and reinstall.

    See Install Doc...

    http://download.Oracle.com/docs/CD/B19306_01/install.102/b15681/reqs.htm#BABGCEAI

    If this help you score as useful... thx

    Kind regards
    Levi Pereira

  • Linkysys RV042 QuickVPN to router problems

    Hello

    Any help with this issue is greatly appreciated because I was stuck on this for a few days now, it's my first time posting to a forum... I have setup VPN connections before, but only through packages such as openswan and openvpn not through this device.

    My VPN router is connected directly to a DSL modem, directly behind the RV042 I placed my test on port machine 1 time Wan1 & port 1 show as Gree (active).

    Modem...
    DHCP enabled

    local IP address: 10.1.1.1

    The VPN has...

    Wan1: 10.1.1.2

    LAN1: 10.222.43.1

    Test machine...

    IP address: 10.222.43.100

    I got two Linksys RV042 Setup devices such as end point / VPN connections between one local area network to another.

    However before doing that I tested the installation of a test machine (for laptop Windows 7 Professional & also tried XP Professional with exactly the same results) for the VPN router device. I have configured the router with the basic configuration, as described in the guide step by step / pdf and user test configuration & a tunnel I left every thing as default and only changed what is necessary.

    I generated a certificate for the server and distributed a client certificate on my customer's computer and installed in the "C:\Program Files (x 86) \Linksys\Linksys VPN Client\" directory (if I understand correctly I can simply upload to this place and its installed for the customer).

    Above is a race down the steps listed in the installation guide provided on the CD, whenever I try to connect to the server, I get the following error message.

    Failed to establish a connection.
    

    This could be caused by one of the following:
    

    1. Incorrect password.
    

    2. No valid IP for the network card.
    

    3. Incorrect server address.
    

    4. You may need to disable your Windows firewall.
    

    5. Local IP address conflicts with the subnet of remote VPN server.

    1. I know that my password is correct

    2. I don't know what that means 'no IP address valid for the network adapter', although I am able to access the internet via the modem on my test laptop and have access to the web interface of the RV042 so I assumed that my IP is valid?

    3. I know that the address of the server is correct, I tried the two internal address of the RV042 and address the RV042 wan1

    4. I get exactly the same error message if the firewall is enabled or disabled on the XP or 7 machines.

    5. it's one I leave me puzzled, there is no connected computer so I don't know how there could be a conflict. However, just to make sure that I changed the IP address of the laptop outside the range allocated to the tunnel, and I still get the same error message.

    I checked the "system log" server log file and that's what I get, it appears that the server actually accepts the connection between what I can make of this series of posts.

    Jan 22 10:32:04 2010         Connection Accepted         TCP 10.222.43.100:3374->209.46.39.47:443 on ixp1
    


    Jan 22 10:32:32 2010        Connection Accepted        ICMP type 8 code 0 10.1.1.2->10.1.1.1 on ixp1
    


    Jan 22 10:33:44 2010         Authentication Success         HTTP Basic authentication succeeded for user: test

    The log on the local machine, however, show that there is an error but it just says: "Failed to connect" so I am very confused about the whole issue.

    2010/01/22 11:46:13 [STATUS]OS Version: Windows XP
    


    2010/01/22 11:46:13 [STATUS]Windows Firewall is OFF
    


    2010/01/22 11:46:13 [STATUS]One network interface detected with IP address 10.222.43.100
    


    2010/01/22 11:46:13 [STATUS]Connecting...
    


    2010/01/22 11:46:13 [STATUS]Connecting to remote gateway with IP address: 10.1.1.2
    


    2010/01/22 11:46:14 [STATUS]Remote gateway was reached by https ...
    


    2010/01/22 11:46:14 [STATUS]Remote gateway was reached by https ...
    


    2010/01/22 11:46:14 [WARNING]Failed to connect!

    Thanks for reading and thanks in advance for any help provided.

    JC

    As your objective here is to do a LAN to LAN VPN, I don't mind playing with the VPN client software to test the router.  The VPN configuration can be pretty shakey on the rv series, and I recommend that you play with the options, just keep base.

    Set up each local network be on a separate subnet.  That is to say, we're on 192.168.1.x, 192.168.2.x on.  On the VPN tab, set up accounts for both gateway to gateway vpn routers.  Test the connection into the router admin screens.  Check the connection with pings to each side of the lan systems.  Then try to use applications/files that you plan to use and see if it works.  If so, then success!  If this is not the case, check the different options to the title of each gateway account.  These options can make or break the vpn connection.  Good luck.

  • RV042 routing problem

    I try to use the rv042 as a primary internet connection and also as a VPN failover for my primary private WAN connection.

    I have a load balancer / failover device, called a Fiberlogic, which acts as the main router to network my office remotely.  This device shows you all the traffic to my private network go to junction A and all Internet traffic going to the B connection (connection B is the rv042).  If the fiberlogic sees this connection is down, it will send the connection B's private network traffic.  The RV042 has a VPN setup, I tested it and it works.

    However, I have one VERY difficult to get the RV042 to act as our internet gateway.  The RV042 is in mode "gateway."  Devices plugged into it directly (or via an external switch) work very well.  The RV042 LAN is 10.2.254.0/24, and he est.1.  FiberLogic est.254.  The main network is 10.2.0.0/24 (and the FiberLogic.1.  The FiberLogic road all traffic to the internet (and for failover) of 10.2.254.1.  I have install a static route for the RV042 road 10.2.0.0/24 to 10.2.254.254.

    I had a ton of problems with this earlier today.  I have a second RV042 I put in to see if that would fix it.  There can be no.  Finally I have restored the default settings and reset the top, and I thought it worked.  As I was cleaning the I did one last test - and it failed.

    I have install a hub between the FiberLogic and the RV042 and configure a computer with Wireshark to do some packet traces.  I get strange results.  I never get a repyl.  SOMETIMES I see answers from 10.2.254.1 (the RV042) towards 10.2.0.25 (my desktop) in wireshark, even if I don't get them (odd).  However, whenever I have ping to internet, I never see the answers, only applications.

    I read that DHCP should be disabled for a static routing to work.  I tried with and without DHCP several times.  I tried with and without VPN.

    Once again, peripheral not behind the fine work of fiberlogic (i.e. on the 10.2.254.0/24 subnet that use the RV042 as gateway).  UT behind the fiberlogic devices fail.

    Any help would be greatly appreciated.

    RV042 Rv082 and RV016 router can be configured for additional NAT networks who are sitting behind the LAN.

    1. log on to the router

    2. go in the configuration Page

    3. roughly halfway down the page, there are article that says "several Setting subnet.

    4. click on the button that says "Add/Edit."  This will bring up a dialog box

    5. Enter the network number and subnet mask, then click 'Add to list' for example network: 192.168.200.0 mask subnet: 255.255.255.0

    6. click on save changes

    7. that you will return to the previous page in the installer

    8. the checkbox in Multiple subnet must be checked and the second network to be coordinated should be

    9. click on the page to "Save settings" at the bottom of the page

    I note: the latest version of the firmware for the RV016 seems to prefer to have this process done with Internet Explorer.

  • Put in Server cache does not cache its own installed on App Store

    I've set up the OS X Server App 5.1.5 (15S 7047) on an iMac running El Capitan 10.11.5 (Build 15F34). The iMac has 8 GB of Ram and a processor i5. It's mid-2011.

    He belongs to a Windows domain and put in a Time Capsule in Bridge mode.

    On the iMac's settings, etc.. :

    Overview of the server:

    Internet: Can be reached at 202.etc., no service available

    Public host name: no

    Network interface: Ethernet, Ip address 192.168.0.70 (assigned by DHCP - not static, but it never changes)

    Accounts: All users, all groups (filled by the domain Windows - Active Directory for the Windows domain controller).

    Only the caching Service is enabled.

    The said status caching service "available - devices on your local network automatically uses this service."

    Permissions: Only the local subnets

    Serve customers with public addresses: mapping network from this server.

    ICloud data: unchecked data cache personal iCloud

    Available cache: 150 GB

    Use cache: None

    When installing from the App Store, the cache is unchanged - still nothing.

    I also downloaded a MacBook Pro and nothing is cached as well.

    I'm new to Mac and must have missed a few settings, but have read a lot on various Forums. I suspect the accessibility by saying 'no available services' cannot be part of the problem.

    I checked the logs - log service for caching can help. The first installation of the application server was a week ago, and I see a problem with "black list... demand." "(see below)

    About 12:15 today, I uninstalled the application server by moving it to the trash, removed the Library\Server, etc. then installed the App Server again. Now the failed activity is not currently recorded.

    PART OF THE FIRST INSTALLATION OF THE APP SERVER FOR CACHING OF LOG FOR TODAY:

    June 20 at 11:14:10 dlserver AssetCache [351]: server closing caching (15)

    June 20 at 11:14:10 dlserver com.apple.xpc.launchd [1] (com.apple.AssetCache [351]): Service came out with abnormal code: 15

    June 20 at 11:14:34 dlserver AssetCache [1110]: Server version 149.4 started caching

    June 20 at 11:14:37 dlserver AssetCache [1110]: successful registration.  Recovery of the server.

    June 20 at 11:41:56 dlserver AssetCache [321]: Server version 149.4 started caching

    20 Jun 11:41:57 dlserver AssetCache [321]: request for http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    20 June-11:41:57 dlserver AssetCache [321]: back to the last accepted configuration

    20 June-11:41:57 dlserver AssetCache [321]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

    20 June-11:41:57 dlserver AssetCache [321]: chess 1 consecutive cleaning.  Retries in 16 seconds.

    June 20 at 11:42:18 dlserver AssetCache [321]: successful registration.  Recovery of the server.

    June 21 at 08:55:28 dlserver AssetCache [319]: Server version 149.4 started caching

    June 21 at 08:55:28 dlserver AssetCache [319]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    June 21 at 08:55:28 dlserver AssetCache [319]: back to the last accepted configuration

    June 21 at 08:55:43 dlserver AssetCache [319]: successful registration.  Recovery of the server.

    June 21 at 10:07:47 dlserver AssetCache [334]: Server version 149.4 started caching

    June 21 at 10:07:49 dlserver AssetCache [334]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    June 21 at 10:07:49 dlserver AssetCache [334]: back to the last accepted configuration

    June 21 at 10:07:52 dlserver AssetCache [334]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

    June 21 at 10:07:52 dlserver AssetCache [334]: chess 1 consecutive cleaning.  Retries in 63 seconds.

    June 21 at 10:09:07 dlserver AssetCache [334]: successful registration.  Recovery of the server.

    June 21 at 10:15:53 dlserver AssetCache [307]: Server version 149.4 started caching

    June 21 at 10:15:53 dlserver AssetCache [307]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    June 21 at 10:15:53 dlserver AssetCache [307]: back to the last accepted configuration

    June 21 at 10:15:57 dlserver AssetCache [307]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

    June 21 at 10:15:57 dlserver AssetCache [307]: chess 1 consecutive cleaning.  Retries in 60 seconds.

    21 June 10:17 dlserver AssetCache [307]: successful registration.  Recovery of the server.

    June 21 at 12:05:11 dlserver AssetCache [287]: Server version 149.4 started caching

    June 21 at 12:05:13 dlserver AssetCache [287]: application of http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    June 21 at 12:05:13 dlserver AssetCache [287]: back to the last accepted configuration

    June 21 at 12:05:13 dlserver AssetCache [287]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

    June 21 at 12:05:13 dlserver AssetCache [287]: chess 1 consecutive cleaning.  Retries in 72 seconds.

    June 21 at 12:06:30 dlserver AssetCache [287]: successful registration.  Recovery of the server.

    June 21-12:14:36 dlserver AssetCache [287]: server closing caching (15)

    June 21-12:14:36 dlserver com.apple.xpc.launchd [1] (com.apple.AssetCache [287]): Service came out with abnormal code: 15

    (THIS IS THE POINT WHEN THE APP SERVER HAS BEEN REINSTALLED)

    21 June at 14:55:50 dlserver AssetCache [2986]: Server version 149.4 started caching

    21 June at 14:55:54 dlserver AssetCache [2986]: successful registration.  Recovery of the server.

    BUT STILL NO CACHING OF HIS PEOPLE MOVED FROM THE APP STORE.

    I also tried it with OS X Firewall disabled, Avira Real - Time Protection off tension, but nothing is.

    I suspect the State available services no. for the Internet parameter, mentioned at the beginning of this post, to be meaningful, but did not find what is missing.

    I thank very you much for any help.

    Update:

    After downloading a few elements of the App Store, this poster now implementing log cache (again). I have certainly given internet I installed from the App Store:

    June 22 at 09:50:12 dlserver AssetCache [314]: Server version 149.4 started caching

    June 22 at 09:50:12 dlserver AssetCache [314]: request for http://suconfig.apple.com/resource/registration/v1/config.plist configuration failed: the Internet connection appears to be offline.

    June 22 at 09:50:12 dlserver AssetCache [314]: back to the last accepted configuration

    June 22 at 09:50:12 dlserver AssetCache [314]: http://suconfig.apple.com/resource/registration/v1/blacklist.plist blacklist request failed: the Internet connection appears to be offline.

    June 22 at 09:50:12 dlserver AssetCache [314]: chess 1 consecutive cleaning.  Retries in 74 seconds.

    June 22 at 09:51:40 dlserver AssetCache [314]: successful registration.  Recovery of the server.

    And nothing is recorded in the Server Cache.

  • I installed the version 9.0.1 v10 Firefox has crashed maybe 20 times since then. The previous version almost never crashed AND it changed as if by magic of my network connection settings.

    I installed the version 9.0.1 v10 Firefox has crashed maybe 20 times since then. The previous version almost never crashed AND it changed as if by magic of my network connection settings. disable/change actually my DHCP
    -J' I disable all my Add-ons and rebooted w/no probs but it's crazy.

    I found a FF v9 online and install it. So far it works. I'll pass on challenging FF v10

  • Satellite P300-156 - cannot install any OS

    Hello

    I had a P300-156 for a while.
    It was fine until recently, when the DHCP client stopped workin and wouldn't start.

    So I tried to restore from disk and had no dice with that try.
    So I tried to recover from HARD drive again once any chance the laptop keeps freezing after installation.

    So I tried to install Ubuntu on the laptop but still the same problem, said linux 'buffer I/O sdo error "?
    I'm not sure what in other words, it has however managed to wipe the entire drive.

    And I can not install XP because it does not find the HARD drive.

    The situation is so that I don't have any of the recovery methods and that you can not install another OS.

    Guys im really confused on the topic of what to do here, so if anyone can help please I need.

    Hi James

    I'm not sure if your HARD drive is dead or not, but you should know that your installation of Win XP does not recognize the HDD too if the SATA driver has not been included.
    The fact is that your P300 was equipped with the SATA HDD controller and the SATA driver is needed and if you want to install an operating system.

    The SATA driver is part of the Intel Matrix Storage Manager.
    So if you want to install XP on your P300, you must first include the SATA drive in the XP installation CD.
    This can be done very easily using a free software called nLite.

    This Toshiba doc would be helpful for you because if describes step by step how to include a driver SATA;

    Check this box:
    [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

    Good bye

  • Satellite C870-1J6 wired LAN DHCP problems

    Hi all

    Here, I have a new laptop C870-1J6, which makes my life miserable. It won't start not reliable PXE, and the network card also does not start in Windows.

    On a cold start the PXE boot Gets an address dhcp fine most of the time, but a warm reboot fails most of the time.
    In windows this NIC also does not start. After five to ten minutes, he finally gets an address from the DHCP server. Rest of the network works fine.

    No points for guessing the manufacturer of the network card, of course, there a realtek :-(
    "RTL8102E/RTL8101E PCI Express Fast Ethernet controller.
    PCI ven: 10EC, dev: 8136

    None of the solutions, or can send Toshiba somehow? because I don't think I can do a lot on the PXE problem myself.

    At first, I have to say that I m really wondering why you have problems of LAN under Windows.
    Have you noticed these LAN issues from the first day of use?
    Are you using the original pre-installed OS that you got with your laptop or a facility clean or even company?

    Maybe stupid question, but I assume that LAN is set as first boot device, right?

  • C6380 Wireless will not install on my laptop

    I try to install the C6380 wireless - whenever I get to the printer part to find the facility, it indicates there is no printer on the network.  The priter config. page displays the correct network name.  I am using windows XP and have downloaded the patch to service.  Any susggestions?

    First step is to check that your printer is on your wireless network.  Using the IP address of the printer, if you can navigate the printer web page?  If you can't, then restart the Wizard Wizard from the printer setup menu.

    If you can browse the web page of the printer, you can consider uninstalling the firewall, run the SW installation and the re - install the firewall.  This ensures that the firewall is disabled.

    A final element is to add a reservation your router DHCP IP addressed printer wireless.  In this way, the IP address of the printer will never change after installing the SW.

    Best regards / Jim B

Maybe you are looking for

  • Lost administrative password recovery options

    About once a day, I see the same post "I lost my administrative password for my computer" "I don't remember my password" "I need to change the password and I don't remember" Without failure, we put the passwords and forget about them and it is not al

  • No secure WiFi connection. Need firewall software?

    my wifi connection is not safe here, believe so I need to install a firewall on iPad software to enable my email be directed to real addresses I choose to send them to, rather than, when seized upward, and the word 'send' is pressed, then this partic

  • so...

    Hello I have a little problem here... I don't really want to call to get help from apple to fix this... the answers to my security questions that I've never needed before... ACC on my Itunes is the US itunes and I currently do not live there because

  • HP laserjet 2605dn: printing from mobile phone from samsung s5

    I have an amazing dn 2605 that prints from all devices on a network except my fairly new samsung galaxy s5 wireless. The phone recognizes the printer and sends the image to it but the printer just print a solid black box instead of the image. Tried s

  • Screen turns off [Windows 7]

    When I don't shake with the mouse screen turns off. I can't fix it by waving the mouse I have to restart the PC so that I can do anything on the computer. I had this problem twice. Please help!