Dimension 3100, DVD burner?

Similar Questions

• Master IDE HDD to slave in Dimension 5100 DVD burner

  Hello

  I just added a disk IDE (PATA) (jumper to master) to the same controller that my existing DVD burner, now set as slave. the two IDE channels is enabled in the BIOS and the hard drive passed Diagnostics.  But the new IDE HDD is not recognized by Windows, although it appears like a hard drive under Device Manager.

  The recommendation of the forum seems to favor using an external HARD drive enclosure, but I'm not willing to do unless it's the only way to make it work.

  What else is required to complete the configuration?  I am running XP Professional.

  David

  
  

• CD/DVD Burner on Dell Dimension E310 player interface

  I have a question. I'm about to add a CD/DVD burner to my E310, but I do not know which interface has my computer. Should I buy an IDE or a SATA interface? I am considering buying one of the following readers below according to the interface that uses my E310. What I have to buy cables or do they come inside the computer already? And I want to know if I need to configure something after that I installed the drive on my computer.

  IDE - drive-

  http://www.Newegg.com/product/product.aspx?item=N82E16827118011

  -SATA Drive-

  http://www.Newegg.com/product/product.aspx?item=N82E16827118012

  Thank you!

  
  

• Dell Dimension 9150 / XPS 400 DVD BURNER

  Hello

  The DVD burner I have in my XPS 400 is a HL-DT-ST DVD + - RW GSA - H21N

  This player supports burning double layer DVD? I looked and looked on google but could not find an answer to anywhere!

  
  

• I can build in the Satellite Pro 4600 DVD burner?

  Hiya

  Can anyone help with this? Has anyone equipped with a DVD burner (dvd - rw drive Toshiba sd-r6252)?
  Which models are compatible? I'm good fight opening and Exchange.
  Compatibility just in fact know.
  Thank you

  Hello

  I put t found any information if this drive is compatible with the Satellite Pro 4600, but you should be careful to replace the drive.
  You should check the dimensions of the car. Very important is the drive (master, slave, csel) settings because it is not possible to change this settings as on the usual desktop drive.
  I'm not sure about the settings on the Satellite Pro 4600 but the ASP Toshiba should know that.
  You can also order the caught player supported by the Toshiba service partner in your country.

• "Stop error" suspected to cause driver corrupted for user installed DVD burner.

  I get a "BSOD" (blue screen of death) everytime I go out with my Philips DVD burner. Under XP Home on a Dell Dimension 2400. Installed this writer a couple of years ago and have used it without any problems, however started getting this error about 6 months ago. MS produced a report when I rebooted after the last incident - "you received this message because a device installed on your Windows computer driver stop unexpectedly." This type of error is referred to as a "stop error" that requires you to restart your computer. "I followed all the steps described in this report to address the cause of the erroor. However, one of the steps refers to "Uninstalling the driver", but it is a step of manned by menu windows which seems to me that it's not really uninstall the driver - it's just a procedure they wrote such fact, it (start - control panel - display categories - Perf. & Maint - system - hardware - device Mgr - disabling/uninstalling). After you follow these steps, you get a message from re - install the device by clicking on a box. In my view, the same driver is used. It is corrupt nothing has changed and I will continue to get this error. I would like to know where the real driver is located so I can delete it and then go online to download a new driver. However, because my o/s came pre-installed by Dell, MS isn't going to help (unless I pay for the help) and Dell won't help because they didn't install the unit and the Philips site is useless in trying to get technical information as to where their driver is on my hard drive. I checked Event Viewer - System Log and found 'Source = system error category' and the real codes of 4 parameters (addresses memory I think) [that MS would only be able to interpret] for this date and time. I might have to go the route of 'pay' people with MS, but before doing that I would try to fix it myself. Dell site will not download the driver that already exists on my HD and is the latest version. Tools Dell system does not include this unit in its analysis of material either. So - I hope that someone will be quite kind to give me any suggestions where to find this particular driver - I can't find anything that looks like a pilot in the Philips records. Thanks for any help offered too!

  Hello
   
  (1) what is the complete stop of exact\ error you get?
  (2) what you mean exactly by I get error on a blue screen when you quit using my Philips DVD burner?
  (3) burner DVD from Philips, you have, it's an internal or external DVD burner?
   
  See the methods mentioned below and check if that helps
   
  Method 1:
  How to solve problems of hardware and software drivers Windows XP
  http://support.Microsoft.com/kb/322205
   
  Method 2:
  Try to uninstall and reinstall the drivers
  Follow the steps mentioned below and check if that helps.
  (a) click Start, click run, type devmgmt.msc
  (b) expand CD-ROM/DVD-Rom drives.
  (c) make a right click on the Dvd drive and click on Uninstall.
  (d) restart the computer.
   
  Method 3:
  Try to download the drivers from the following Dell Web site and check if it helps.
  (a) click on the link below
  http://www.Dell.com/support/drivers/us/en/19/DriversHome/NeedProductSelection
   
  (b) select to choose from a list of all products Dell, click on desktop computers.
  (c) click the Dimension, and then select the model as a Dimension 2400 number                            
  (d) if the Philips Dvd burner is an external tries to download the firmware under removable storage called Philips in the above mentioned link.
   
  Hope this information helps.

• DISCS DVD BURNER / can I replace it with new grade DVR_RW and software up, which comes from withDRIVE

  Have more old Dell computer/Dimension 4500/P4 2.4gig / iGig Ram

  running WINDOWS XP PROFESSIONAL,

  ? He is working have new in the box of DVD burner/22XDVD + R writing speed.

  8.5 GB DVD + Double layer 16 x

  DVD_R 22 X / DVD + RW 8 X/DVD-RAM 12 X / 16 X/DVD-R DL 12 X DVD + DL? CD-R48x/CD-RW 32 x.

  Registration of NERO software (Nero Express in CD)

  CyberLink & playback software

  (PowerProducter, Power DVD)

  Process CONTROW PANEL? Remove sign dvd player / then turn off computer computer open remove old drive IDE cable

  and DVD player instal Moses / if the sound card has Digital Imput add a new cable of cable/ide audéo,.

  When starting in safe mode to remove any old player not yet deleted.

  computer restart lodge on add new hardware chect, should ask to reboot to complete. ?

  If it works? Feedback wellcom

  THANKS: 4ROB

  Hi 4ROB,

  You will be able to connect the DVD recorder and install the Nero app on it, but the reader must have the connector of the IDE cable instead of SATA cable connector as the Dell Dimension 4500 comes only with the IDE connector on the motherboard.

  Please respond to all queries.

• DVD burner does not recognize a DVD + RW

  I recently bought a DVD burner, after getting advice from Dell, to replace the original equipped DVD ROM (?) in my Dell Dimension 4500, so that I could record my video movies on DVD discs.

  The DVD burner, I was recommended is the ASUS DRW - 2014L 1 and this was provided by one of the "registered partners" from Dell. Unfortunately, this "Registered Partner" was useless, aggressive & dismissive to all after sales help or advice, where my request on this forum for assistance or advice.

  I had no trouble to record my videos on blank DVDs DVD - RW drives, but when you try to use DVD + RW discs (to use in my Sony Home DVD drive), the drive will not recognize them. Both the + RW & - RW discs are brand new Maxell disks, the RW - 1-2 x speed, single-sided 4.7 GB & the + RW 1-4 x speed, single-sided 4.7 GB.

  When there is no record of any type in the DVD drive, it shows in my computer as: DVD - RAM Drive (D). When a DVD - RW disc is inserted it changes to: CD Drive (D) with an icon of DVD - RW & this is also confirmed when I check on the properties.

  However, when you insert a DVD + RW and the DVD - RAM Drive (D) going to Drive (D) CD, as with the DVD - RW, no icon is displayed to indicate the drive is recognized, or it appears in the properties.

  As far as I can determine from the card, the ASUS DRW - 2014 L 1 is designed for both + & - DVD.

  I'd appreciate any help or advice... or am I just dumb?

  Thank you

  Tony

  Message edited by ozwald on 10/09/2008 02:36
  
  

• Add IDE HARD drive in Dimension 3100

  Hi all

  I have a Dell Dimension 3100, the system disk is a sata drive, I added an IDE HDD to the position of the secondary cable on cable connecting a DVD player, I put the disk in slave (not connected riders). I am able to read and write on the disc but its extremely slow, suggestions.

  Cheers, Malcs

  
  

• DVD burner does not recognize blank DVDs, but will recognize blank CD?

  I read through several similar messages, but none seem to have a solution to my problem.  I'm NOT very technically savvy, so this is as much I know:

  I have a Dimension E310

  It was supposed to come with a cd burner and a dvd burner combo.

  The reader says DVD R/RW RW DVD rewritable Compact Disk its Ultra Speed

  I was able to successfully burn CDs from itunes, but have not been able to burn any kind of video file.  In fact, when I insert a blank dvd in the drive, the computer does not recognize that everything is there.

  As I said, I'm not the person most computer savvy in the world.  I know how to work with my applications, but I know little about the way in which a computer is set up, so I apologize in advance if my question is ignorant, but I appreciate any help you can give.  Thank you in advance.

  
  

• laptop DVD burner

  My laptop DVD burner doesn't work on my admin account no problem (a years) but not on my account (all inclusive) children. TI spit just the DVD of return. In preferences systems on both accounts I wrote to ask what to do with a blank DVD but it never done on the children and it does on mine.

  Thanks for any help.

  Hello lareianne,

  Welcome to the communities of Apple Support!

  I see from your post, that on behalf of your children on your iMac is not able to burn DVDs. I understand the importance of being able to burn DVDs, I have do this a lot on my iMac. I'm happy to help you with this.

  Use OS X El Capitan: set up parental controls and check the restrictions of parental control to see if burning CD and DVD is blocked, specifically, this section:

  All restrictions

  1. Choose the Apple menu > System Preferences, and then click Parental controls.

     Note: When you open parental controls Preferences, if you see the message "There is no user to manage accounts", see Add a managed user.

  2. Click on the lock icon to unlock, then enter an administrator name and password.

  3. Select a user, and then click a button at the top.

     • Applications: Prevents the child to use the built-in camera. Limit contact of the child with other people through the Game Center and Mail. Specify which applications can access the child.

     • Web: Limit access to Web sites, or allow unrestricted access.

     • Stores: Disable access to the iTunes Store and the iBook Store. Restrict access to music, movies, TV shows, apps and books to only with notation adapted to the age of the child.

     • Time: Set time limits for the days of the week, weekend and sunset.

     • Privacy: Allow the child to make changes related to privacy.

     • Others: Block using the dictation, access to the printer settings and burning CDs and DVDs. hide profanity in the dictionary and other sources. Prevents the Dock to be modified. Provide a simplified view of the Mac desktop computer.

  Best regards.

• -DVD burn does not work in the DVD player sometimes

  I have a Mac Pro from the beginning of 2008, and it came with a DVD drive (OPTIARC DVD RW AD - 7170A).  I was able to burn DVDs with using toast in the past.

  But lately, the half of the DVD burn won't play in my DVD consumer player.  I get a "Disk error" message when I try to play them, and they do not load.  It's a strange problem, because some of them work and some do not.  I can't tell where the problem is.

  Is there a way to test the DVD player?  Should I just replace it?

  Many brands of blank DVDs gives very inconsistent results when burning. If you use a brand store or generic blanks, that may be the problem.

• iDVD on the part of an external DVD burner

  The optical drive on my mac mini 2009 died. I need to burn a project to a DVD. I have attached an external DVD burner for mac. I play DVD. How to record from iDVD please?

  I had a similar set on one of my Mac mini.  My internal optical drive still works fine, but I bought an external burner because the Apple optical drive cannot burn the M-DISC.  (M DISC is what we use now.)

  http://eShop.MacSales.com/item/OWC/MR3UBDRW16/

  Don't burn your DVDs from iDVD. Instead, use iDVD to create an image file and then burn the image file using the disc utilities. Utility disk will be out and find all your drives connected and it should see externally, (he does with us).

• By Satellite Pro S300 uses double layer DVD burner

  Hello

  Sorry for my bad question, but I have a DVD burner double layer on my Satellite Pro S300?
  THX

  Hello

  Do you have your read the user manual?
  In manual mode, you will find information on the CD/DVD drives properties;

  Always is that the Satellite Pro S300 series was equipped with different CD/DVD drives
  TEAC DV-W28S and Panasonic UJ870 are readers of DVD super multi and support media Double layer + r.

  You can also find more information on the CD/DVD drives that are installed by using the Nero Burning Rom. There is an option that shows you all types of CD and DVD that is compatible with the internal SIDE

• Portege A100 - problems recognizing a new DVD burner

  Hello

  I'm looking to replace the Panasonic/Matsu * player UJDA750 combo with a LiteOn SOSW - 852S DVD burner. The LiteOn is CSEL and is not recognized by the Portege A100. I tried to change the master/slave/CSEL and Inverse CSEL using E2MS_WIN_SOSW - 852 S .exe (in an Acer Travelmate 220, which sees all configurations), but the Portege A100 still does not recognize LiteOn.

  I ran IDEDIAG using a WinME boot CD and the Matsu * a Combo drive in Portege reports as secondary master. So, I tried flashing the drive LiteOn (using the Acer Travelmate platform) with MTKFlash version 183 c using the a command? "mtkflash 3 w/b PRS9.bin" (using the original firmware of saved), '3' to change the drive to the secondary master. I came across problems here - the flash appears to hang. The drive is always ok, however. I flashed it back to the original ok CSEL using E2MS program in Acer.

  I have not tried bridging the pins 45 to 47 on the LiteOn - I thought maybe it was a last resort.
  -Can help you with the correct configuration for a CD/DVD drive in the Portege A100? There are a bunch of different ones - primary, secondary, tertiary, Quarternary master/slave and CSEL and Inverse CSEL. Portege A100 'sees' the Matsu * a CDROM model CR-176_B of Acer.

  Or - can you recommend me a DVD burner for this laptop?

  Hello

  The evolution of the master/slave/c-salt settings is not recommended and tell the truth I put t know if its possible. I presume that it of not possible to Flash these settings on medium power.
  In my opinion it doesn't make any sense to do.
  This procedure may damage the drive. Maybe you will not be able to use this drive more and more you will void the warranty!

  I think it s better to buy a compatible device and supported as trying to drive not compatible flash.

  Did you check your user manual? Usually the user manual should provide information on compatible CD/DVD players and supported.

  Good bye