Directories of Cisco C90

Similar Questions

• Board of Directors of Cisco Leader of CSC

  Is an employee of Cisco Council leader of CSC? If this is not the case, perhaps we should consider a?

  Hi George,.

  Yes, we have an employee of rankings.  You can find them here.

  See you soon,.

  Dan

• SX20, MX300 and Cisco C90 multisite functionality

  Hi all

  Someone has information on how to Install Licenses Multisite L-C90-MS, LIC-MX300-MS and MS-SX20-LIC?  These is installed directly in the codec? what procedure?

  Thank you very much!!

  Mario,

  This is the option buttons that you add directly to the codec. Just go to maintenance > upgrade and paste the option key pressed in the key field of the option. This usually requires a restart when completed.

  Adam

• Cisco Codec C90 with three cameras

  Hi gurus,

  We plugged three cameras to Cisco C90. All cameras are connected with Garland and HDMI cables goes to the codec.

  main camera connected to, a second camera HDMI connected to HDMI 2 and the third camera to HDMI 3.

  Under the video input, we changed the interface of three DVI HDMI sources and the type of PC to the camera.

  Now, I have two problems,

  1. for presentation sharing there is no PC option, is to show only the camera three, DVD camera and document.

  2. Since the touchscreen, we are not able to control the camera 3.

  We were able to control the camera with remote but not with touchscreen 8 three.

  Kindly advise me for more top issue.

  BR

  What is the current version of the firmware of the C90?

  ' 1-presentation sharing there is no PC option, is to show only the camera three, DVD camera and document.»

  -  What input you used to connect to your PC for the presentation? What input connector?

  You mentioned that you have already used a HDMI 3 input for the third camera to allow to use the available video inputs or input 4 (HDMI) or 5 (DVI) for entry-level PC presentation.

  C9.PNG

  

  Log on to the web interface C90 and check the configuration Configuration > System Configuration > video.

  For example, you connected the PC presentation on line 4 (4) using HDMI, as shown in the figure. Change the Type name for PCand PC .

  C90.PNG

  

  "2 - of the touch panel we are not able to control the camera 3."

  -  Check the configuration under your input video n ° 3 of the Source.

  Type: camera

  Under CameraControl:

  CameraId: 3

  Mode: on

  C3.PNG

  

  Kind regards

  Acevirgil

• Module MDS 9513-48 ports with the 'Suspended' State Bootflash

  Hi team

  We have a module in our Director of Cisco MDS9513 as below with bootflash State "suspended".

  Module; DS - X 9248-96 k 9

  Switch MDS 9513 (13 Slot)

  Firmware: 5.0 (4B)

  Is it possible online to change the State to return to the 'race' bootflash without reseating the module?

  Appreciate your quick response in this regard

  Status of frequency test action

  -----------------------------------------------------------------

  Bootflash 10s suspension allowed

  5 active EOBC sec race

  Loopback active Running 5 sec

  AAGR 1 day active Running

  -----------------------------------------------------------------

  Hi Anand,

  It is an indication that bootflash failed on the line card and the line card needs to be replaced.

  If the line card is now in place and that you reinstall / reload it, I would expect the next State to be 'off' because the card online is unable to load the firmware.   You should leave it until you can have it replaced.

  Best regards

  Jim

• How to back up the local directory/favorite in the C series or series EX with TC5.0

  Hi all

  I would like to know there is any method to safeguard the local directory/favorite in the series C or EX-series, with TC5.0. On the other hand, we have configured the root account.

  We found the local phone are stored with FolderId (localGroupId-3).

  xCommand file directory add

  Add a file to the local directory where the directory entries can be stored. Returns the file ID (localGroupId-3), which is a unique identifier of the folder.

  However, we want the exact location of the folder ID (localGroupId-3), also, is it possible to back up these files in case we need an RMA.

  Best regards

  Ben

  Hello Ben!

  That's the advantage on centrazlied directories, perhaps Cisco could implement user according to

  directories that are centralized yet stored...

  In any case, I see at least two options, you can use the administrator account tsh and run:

  xcommand search directory

  PhonebookId:
  PhonebookType:
  SearchString:
  SearchField:
  Offset: <0..65534>
  FolderId:
  Limit: <0..65534>
  Recursive:
  

  You may need to use recursive or other options for all entries.

  In addition, it might be easier to use the account root and PCs to download local

  the phone book file and copy on a different endpoint, its location is:

  /config/Pb.XML

  Please note the anwer using the stars below and define the thread if it is a response.

  Martin

• Tripartite Cisco C60 or C90 Cisco Conference

  Dear Experts,

  Cisco C60 or C90 of Cisco, codecs that have key MultiSite option allows to display image on screens separate the multipoint Conference, for example to display each participant on a screen connected to the codec during three separate?

  Your prompt response is much appreciated.

  Kind regards

  Nick

  Yes, you must use the composting and the TC console features. See attached link...

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC6/tc_console/codec-c-series_tc-console_tc60.PDF

• C90 Cisco with 7 cameras - chaining

  Hello

  We have installed a codec C90 Cisco in a large training room using 7 1080 HD Precision cameras chaining.

  You have a document on how to configure the C90 with Garland of 7 cameras guides on how to operate the cameras for example spend 1 camera to another and how to use the remote control.

  Thank you very much for the help.

  Hello

  You can use document about Garland of camera and limitation here

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/camera/PR...

  Search for Garland

  About commissioning, whenever you want to use any camera make sure to have it as a main video for the codec, the second thing that must be supported is the remote control should be close to the camera to have adequate control.

  You must of course remote control IR response should come from desired camera, if cameras are close to each other, make sure to set the remote control DIP switch.

  Will you keep the fixed camera position or he has to move, if it is necessary to go you will rely on the remote control or any third party controller?

  Thank you

• Codec C90 Cisco with Mulitple camera

  Hello

  I'm having a problem with the secondary camera is discovered on C90 codec (v7.0.2), two of the camera is connected and HDMI1, HDMI2.

  IAM get selfview main camera only. The two camera is connected in chains and able to control.

  Is there any configuration required to activate the secondary camera of the codec to display free.

  The camera is precision 1080 12 X.

  TNX

  Bobby.

  You can change the source of the main camera using one of the following options:

  The remote control of the menu (don't remember the exact location).

  The web interface, and on the page of call control, the configuration page of the system in the video options.

  The serial port or SSH, you can issue commands directly on the codec to change the camera to help source xConfiguration Video MainVideoSource .

  Don't forget Wayne said, you can have a single camera selected at any time, therefore, you will see whatever the camera is selected as the primary source, unless you use Console TC composite multiple cameras in a single stream to display on the screen.

  https://developer.Cisco.com/site/collaboration/Telepresence/AV-Integrator/tools/TC-console/TC-console.GSP

• Cisco telepresence c90 lost password Admin

  Hello

  I have Cisco telepresence C90 with TC7.2.1

  Admin password is lost. We cannot get into the Web interface. I don't know how to access and reset. Please let me know...

  Have tried the empty password. No use. Thank you

  You need a COM cable for access to the unit through serial and system reset. Restart the system and when you get a fast connection for connection with the user "factoryreset.

  / Magnus

• Search in directories case-sensitive on the endpoints Cisco SX & MX series

  I have a problem when the search engine in the directory on a Cisco SX20 touch 10 or a touch 10 MX200G2 is case-sensitive. My client use search regularly and it's a real problem to have to capitalize each time looking. If a capital letter is not used, the result of research found nothing. SW version is 7.3.5 and 7.3.6

  Is there a way to disable the search case-sensitive?

  Thank you.

  Did some digging, you're sure you run CMA 6.2.0 or later?

  Seems to be a bug with Polycom CMA before 6.2.0, see the Polycom CMA 6.2 Release Notes, bug ID SSGSE-14527.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Cisco/Linksys lacks a PCI Express Wireless N card for desktop computers

  I bought a new gateway last year and noticed that there is no PCI slot for an internal wireless card.

  I've been running on an adapter of game without external G wire hooked to my ethernet port.

  I want to update my system for Wireless-N dual band, but to eliminate the clutter of my office.

  Anyone have any idea when CISCO/Linksys will have to use a card PCI E N dual-band available?

  (I'm willing to beta-test)

  Bill Calderwood

  Quality Director

  Kadient

  You could use a PCIe to PCI card and then use any PCI device you want (as long as he did)

  http://www.Amazon.com/STARTech-PCI-Express-adapter-card/DP/B0024CV3SA

• Switch Cisco 2960/3560 = > recovery password and default settings with the button Mode

  Hi Experts,

  I have some confusion with the button Mode with cisco 2960/3560 switches.

  I read on many forums and articles, but where things are not clear.

  a place given 3 seconds and somewhere is given 7 or 10 seconds.

  Qus1), what is the exact time to press/hold Mode button to perform two following tasks:

  A. password recovery (according to my knowledge 3 sec) good or bad?

  Configuration of the switch (start + run) would be safe

  After the recovery of password? Yes or no

  B. factory default (according to my knowledge 10 dry) good or bad?

  I'm afraid, because if I press mode button more than 3 seconds, then

  It will delete any configuration of cisco switch. Yes or no

  Qus2) I want to recover the catalyst 2960/3560 switch password without

  Start/run configuration to lose. That is my main concern.

  Please tell me how to do this, what will be the time keeping Mode buttom

  in a few seconds?

  Qus3) which means this line

  "If the password recovery mechanism is disabled in switch

  then you will lose all the config.

  This sentence has been given on this forum url

  https://supportforums.Cisco.com/thread/140848

  KS

  Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) port console switch.

  Use the following terminal settings:

  • Bits per second (baud): 9600

  • Data bits: 8

  • Parity: None

  • Stop bits: 1

  • Flow control: Xon/Xoff

  Note: For more information on the wiring and connection of a terminal to the console port, refer to connecting a Terminal to the Console Port of Catalyst switches.

  Unplug the power cable.

  The power switch and take it to the switch: command prompt:

  2900XL, 3500XL, 2940, 2950, 2960, 2970, 3550, 3560, and 3750 switches of the series, to do this:

  Press and hold the mode button located on the left side of the façade, while you reconnect the power cable from the switch.

  2960, 2970

  Release the Mode button when the SYSTEM LED flashes orange and then turns green. When you release the Mode button, the SYSTEM LED flashes green.

  3560, 3750

  Release the Mode button after about 15 seconds when the SYSTEM LED turns green. When you release the Mode button, the SYSTEM LED flashes green.

  The system was interrupted before the flash at the end file system initialization

  loading the operating system software:

  flash_init

  load_helper

  boot

  switch:

  Run the flash_init command.

  switch: flash_init Initializing Flash... flashfs[0]: 143 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 3612672 flashfs[0]: Bytes used: 2729472 flashfs[0]: Bytes available: 883200 flashfs[0]: flashfs fsck took 86 seconds ....done Initializing Flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 switch: !--- This output is from a 2900XL switch. Output from !--- other switches will vary slightly.

  Run the load_helper command.

  switch: load_helper switch:

  Question the dir flash: command.

  Note: Be sure to type a colon ":" after the dir flash.

  Appears in the file system of the switch:

  switch: dir flash: Directory of flash:/ 2    -rwx  1803357                  c3500xl-c3h2s-mz.120-5.WC7.bin !--- This is the current version of software. 4    -rwx  1131                     config.text !--- This is the configuration file. 5    -rwx  109                      info 6    -rwx  389                      env_vars 7    drwx  640                      html 18   -rwx  109                      info.ver 403968 bytes available (3208704 bytes used) switch: !--- This output is from a 3500XL switch. Output from !--- other switches will vary slightly.

  Type rename flash: flash: config.old config.text to rename the configuration file.

  switch: rename flash:config.text flash:config.old switch: !--- The config.text file contains the password !--- definition.

  Issue the boot command to boot the system.

  switch: boot Loading "flash:c3500xl-c3h2s-mz.120-5.WC7.bin"...############################### ################################################################################ ###################################################################### File "flash:c3500xl-c3h2s-mz.120-5.WC7.bin" uncompressed and installed, entry po int: 0x3000 executing... !--- Output suppressed. !--- This output is from a 3500XL switch. Output from other switches !--- will vary slightly.

  Enter "n" at the prompt to abort the initial configuration dialog box.

  --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Continue with configuration dialog? [yes/no]: n !--- Type "n" for no. Press RETURN to get started. !--- Press Return or Enter. Switch> !--- The Switch> prompt is displayed.

  At the switch prompt, type en to enter a mode.

  Switch>en Switch#

  Password recovery

  Type rename flash: config.old flash: config.text to rename the configuration file with its original name.

  Switch#rename flash:config.old flash:config.text Destination filename [config.text] !--- Press Return or Enter. Switch#

  Copy the configuration file in the memory.

  Switch#copy flash:config.text system:running-config Destination filename [running-config]? !--- Press Return or Enter. 1131 bytes copied in 0.760 secs Sw1#

  The configuration file is now reloaded.

  Replace the current passwords that you do not know. Choose a password with at least one capital letter, one number and one special character.

  Note: Replace passwords that are required. You must crush not all passwords listed.

  Sw1# conf t !--- To overwrite existing secret password Sw1(config)#enable secret !--- To overwrite existing enable password Sw1(config)#enable password !--- To overwrite existing vty password Sw1(config)#line vty 0 15 Sw1(config-line)#password Sw1(config-line)#login !--- To overwrite existing console password Sw1(config-line)#line con 0 Sw1(config-line)#password 

  Write the running configuration in the configuration file with the write memory command.

  Sw1#write memory Building configuration... [OK] Sw1#

  For factory reset:

  do not give under the control of factory reset

  Switch#copy flash:config.text system:running-config

  can I copy the running configuration to Flash

  Switch flash running-config #copy:

  Destination file name [running-config]?

  Building configuration...

  [OK]

  Switch #copy running-config startup-config

  Name of destination file [startup-config]?

  Building configuration...

  [OK]

  Review the link for more information below

  http://www.Cisco.com/en/us/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml

  Please note the useful messages.

  Concerning
  Vesta
  "Everybody is genius." But if you judge a fish by its ability to climb on a tree, he will live his entire life, believing that this is stupid. "

• Cisco Jabber 10.5 for Windows boot process

  Hi guys,.

  I had following problem and impossible to find a clue that can move me somewhere.

  A customer has a jabber Cisco 10.5 deployed and integrated with Active Directory.

  Every day, customers are initializing requests of sends customers jabber with phone numbers against the AD domain controller (these figures are not the contactlists - personal or company) and as there is that much more of this question in a moment the utillization of the announcement is almost 100%, which also makes the problem with the connection in outlook (is also integrated with the Cisco Jabber for windows)

  I searched the Web for tips but have not found anything.

  My questions are:

  The data for Outlook Personal AddressBook starting the Jabber questioned via Jabber Localy or domain controller?

  What is the process of starting the Jabber for Windows on the integration of directories?

  Is this a normal behavior of jabber?

  #####################################################################

  Here is the configuration of the config.xml file - jabber (passswords and areas are changed):

   
        BDI
          AD
          AD-IP address

  Field of presence
             389
              DC = presence, DC = domain
         Username
          Password
          Fake
          True

  ###########################################################

  Hello

  Jabber will not interview contact Outlook address book DC until a manual search is made.

  Also default contact jabber, the domain controller for the windows PC host.

  Each time that you enter at least 3 characters (default for search), jabber first find cached contacts, then outlook address book and then search the directory.

  The attached config file is BDI type ie. for MAC computers, it will not take effect in windows PC.