disconnected the cable plug location unknown

Similar Questions

• Equium 2000: How to disconnect the cables strip of motherboard

  Hallo,
  could you please someone describe to me how to disconnect the two flat-band-cables the Equium 2000 with the low Group (readers) motherboard, that the connectors don't get corrupted.

  Thank you!

  Harald mueller

  Hello

  I'm not 100 sure that cables say exactly, but at both ends of the connector, you should see little "clips" or "parentheses". You have to put on the side. So normally it should be possible to pull the cables. But if you do, you should be carefully.
  But if you have no experience of these things, you shouldn't do it. In this case, the best way is to ask the guy to service for assistance.

• Disconnect the cable in a VI script

  How to disconnect the wire between two terminals in a VI script?

  Get a reference to the thread and call the Delete method. If the wire is connected to multiple receivers, you can get references to the source and (other sinks), remove the wire, then reconnect to all receivers other than the one you want to disconnect.

• I always use my laptop with the cable plugged in but the battery icon becomes sometimes red indicating that the load. Can you explain why?

  In a front of my laptop, there is a line of icons.  When I turn on my laptop, all icons become normally blue.  But sometimes, the battery icon turns rered indicate that my laptop recharges.  I always turn on my laptop with the cable is connected, the battery should not turn red, does?  Could you explain?

  Batteries "will always lose" part of their load.  It is quite normal that the laptop checks charge battery and "on upward.

• Satellite L450 - connection loose if I disconnect the cable

  I just tried to configure my modem on my Satellite L450 wireless and it works well with the ethernet cable, but as soon as I disconnect I lose it.
  I tried 3 cables but nothing.

  What can I please?

  Hi ElaKeen62,

  I m a bit confused now... As a first step, you wrote that your WLAN car works well, but then you wrote something on the Ethernet connection and you have tested 3 cables?

  What exactly is your problem?

• LAN broken or disconnected the cable

  the icon in the LAN system tray has a red X and says a network cable is broken or disconnected. my laptop network will connect by mistake. I visually inspected son and they seem ok - is there a way to be sure if it is causing me to lose my connection. appreciate any suggestion

  1. use a different cable

  2. go to start, Control Panel, network connections, right click and choose repair.

  What happens now?

  3. go to start, then right-click on my computer and select manage, select Device Manager, are there points of yellow exclamation that will tell you if there is a problem with a driver?

  4 do the following if you can't connect to the internet, make sure that your system is clean by running a scan with your antivirus which is this?

  5.

  Click Start, run and enter in the box:

  Msinfo32

  Click OK, and when the system info summary appears, click on edit, select all (Ctrl-A), copy (Ctrl-C) and paste (Ctrl-V) the information back here in your next reply.

  You can change the personal information.

   

  Download, install, update and scan with these full free malware detection programs:

  Malwarebytes (MMFA): http://www.malwarebytes.org/products/malwarebytes_free

  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  Remove all found, restart, and run again until analyses race clean, these can be removed later if you wish.

• At the start, st location unknown software Exception (oxc00000d) 0X0045af13

  I get this notice every time I turn the computer.  All programs seem to work correctly.  However, I can't use the Control Panel Add/Remove function.

  Hello

  Run the verification and virus scan online if any malware or virus detected on the computer activity. You can run the scan for viruses online from the link below: http://www.microsoft.com/security/scanner/en-us/default.aspx

  NOTE: Make sure that you select the correct version of the operating system before downloading the scanner)

• XP is not start properly, important data files on the hard drive, location unknown such as e-mail addresses, individual emails and favorite links on Internet Explorer. The system is damaged irreparably, what is the solution?

  I need ideas to solve this problem.

  You can retrieve the data without being able to get into Windows. The methods described require a certain level of computer skills. You know yourself best, and if a better course of action would be to take the machine to a local professional with a good reputation instead. If you choose to do, do not use a type of BigComputerStore/GeekSquad of the place.

  1 remove the drive and put it in a box of USB drive or use a USB adapter. Attach it to a computer that is running a working XP/Vista/Windows7 installation. Use the work of Windows Explorer to copy the data to the hard drive of the system to the rescue and burn data on cd or dvd, or copy it to an external hard drive. I prefer not to do it if I know the drive is infected because he has a chance to infect your host system. In these cases, I use #2 below.

  2. you can start the computer target with a Bart PE (XP only) or Linux Livecd such as Knoppix or Ubuntu and retrieve the data in this way. This has the additional advantage to tell you if the problems you are experiencing are hardware or software related because if the computer behaves perfectly in Linux, you know that Windows (software) is the culprit. Conversely, if the computer behaves badly under Linux, you will know that there is a hardware problem. This is general information on the use of Knoppix for the recovery of data when you do not have Windows:

  You will need a computer with two cd records, one of which is an engraver of CD/DVD OR a USB thumb drive with enough capacity to contain your data OR an external USB hard drive. Download Knoppix .iso image file and create your bootable CD *. If you do this in a previous (XP or Vista) operating system, you will need the third burning like Nero, Roxio or free ImgBurn software (Windows 7 can burn .isos natively). Burn as an image, not in the form of data. Then boot with the CD that you created, and Knoppix will be able to see the files in Windows. If you use the USB key or an external hard disk, right-click on its icon (on the desktop) to get its properties and uncheck "read only". Then click on it to open it. Note that the mouse action by default in the window manager used by Knoppix (KDE) is a simple click to open instead of double-click traditional MS Windows. If you want to burn CD/DVDs, use the K3b program.

  * If your computer has only an optical drive and you want to use this drive to burn data or need to test drive, you can create a USB bootable Linux instead of a bootable CD. This site will show you how to do it- http://www.pendrivelinux.com

  http://www.Knoppix.NET
  http://www.nu2.nu/pebuilder/ - Bart PE Builder

  See also - http://lifehacker.com/5504531/the-complete-guide-to-saving-your-windows-system-with-a-thumb-drive
  And for future disaster recovery programs - http://www.elephantboycomputers.com/page2.html#Backing_Up

  MS - MVP - Elephant Boy computers - don't panic!

• 'Disconnect the PC' button

  I need to be able to detach my machine and cannot find the button "Remove" it is supposed to appear in the Start Menu.  I updated GPedit.msc and follow these steps to disable the removal works, but still do not see the button.

  Click Start, run and type: Gpedit.msc

  Then follow this path: User Configuration-Administrative Templates-Start Menu and taskbar

  Find the Option disconnect and click Properties to enable it.

  More information in the microsoft help to:

  http://support.Microsoft.com/kb/292504

  Please notify.

  Hi Dawn Kelley,

  Connect the laptop to the docking station.
  Note: If you don't see the option 'Disconnect the computer', it is possible that your laptop is not configured correctly for mooring or you don't have the administrative permissions required to disconnect the laptop.

  To detach the laptop computer, follow these steps:
  1. click on start, then click on "disconnect the computer. (Located next to the options for "Stop" and "Restart")
  2. wait for a message appears saying that you undock your laptop successfully.
  Note: Some laptops will not give this message but rather will make a sound confirming that the cell phone has been disconnected.
  3. push the eject button on the docking station downwards until the cell is displayed.
  4. pull the laptop to the station, on the back first.

  Advice and WARNING:
  Computers Dell laptops have the option "disconnect the computer. However, some laptops can have an option for "Eject the PC" in the start menu, instead of 'disconnect the computer.
  It is extremely important to disconnect your laptop computer in the start menu before you eject from the docking station.
  Ejection for a laptop computer to the station before being released on the start menu may cause data loss.
  It can also cause damage to your laptop or other devices connected to the docking station.
  Read the manual of the manufacturer for detailed instructions and equipment for your specific laptop.

  NOTE: If the laptop is not connected to the docking station, and then the pc disconnect button is not available on the start menu.

  Hope this information is useful.
  Let me know if it worked.
  All the best!

  Thank you, and in what concerns:
  Syed V - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• My laptop screen becomes empty whenever I disconnect the plasma

  Recently, I connected my computer laptop to LG plasma to see a movie (using RGB output) and changed the accodringly to display definitions. However, when I disconnected the cable from the laptop, the laptop screen became blank. When I reconnect the cable - I see the laptop screen (even if the plasma is off). Now I'm stuck to work with a cable connected to nothing...

  When you restart the computer, I see the screen, it disappears when windows comes on.

  I've redefined (by using windows + P) the computer screen only - did not help. I've updated the display adapter and monitor in Device Manager - did not help. No virus detected; Nothing to do with the BIOS...

  Ideas please?...

  Hello

  I suggest you to uninstall and reinstall the drivers to display the computer manufacturer's website and check that I get no help.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  Update drivers: recommended links

  http://Windows.Microsoft.com/en-us/Windows7/update-drivers-recommended-links

• My computer is constantly disconnected from the internet and to reconnect I just unplug the cable for less than a second and it starts to work instantly.

  My computer is constantly disconnected from the internet and to reconnect I just unplug the cable for less than a second and it starts to work instantly. Does every 5 to 10 minutes and it gets frustrating. It is not the cable modem because it is constantly connected, and I repeatedly checked.
  I have this problem with all programs on the internet and she does every day and probably every 5 to 10 minutes.

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  Sync your iPhone, iPad or iPod touch with iTunes using a WiFi - Apple...

• Jack was very warm when you disconnect the plug iPhone

  When my iPhone 6 supported this morning, I noticed the plug that goes into the wall was pretty hot when I disconnected the unit from the wall.  I never noticed this before.  Is it a bad sign and is it safe to use?

  On the phone under 80% charge when you unplugged? If Yes, the cube would be hot, because the phone draws more power for the first 80% of the load, it then tapers. If you have any doubts bring it to an Apple store for the assessment.

• the unknown software exception (0xc0010000) occurred in the application at location 0 x 77564598

  Help me!!!

  the exception unknown software exception (0xc0010000) occurred in the application at location 0 x 77564598

  It also begins by like 100 MB of ram then 1.5 GB of ram

  Help!

  some please tell me how to fix it thx

  I don't know if this has anything to do with this leak memory, but try to uninstall CyberLink Webcam Splitter (application CyberLink YouCam) and Avnex Virtual Audio Device (XSplit application).

• Envy of HP dv6-7210us: No TV sound when the cable HDMI plugged to the PC

  Hello.  Worked last week and the connection mths prior HDMI, TV had sound.  This weekend, 20/08/16, the TV sound went, but still had the video.  Watched forums, utube and do the audio control panel Device Manager.  Audio high definition Digital Audio-AMD display device; not plugged in is grayed out.  clicked on it does not.  the default configuration is also grey so I can't even define a default value.  PC speakers.  bought a new HDMI cable but no change.  all the drivers are up to date.  not really sure what happened.  has worked for months and now no sound.  any idea?

  Hi @glgar1,

  Welcome to the HP Forum! Thank you for becoming a member of the HP Forum. It's a place dynamite to get help from the community, to get suggestions and find what has worked for others. Because you have the best experience, here is a link for you to see, if you have concerns: first time here? Learn how to publish and more

  I understand that you had previously no problem with the sound of the TV connected via HDMI. Last weekend, the noise disappeared. You have looked at the HP Forums, YouTube and checked in the Device Manager. Audio high definition Digital Audio-AMD display device; not trendy, is grayed out. and you clicked on it nothing doesn't. The default configuration is also grayed out, but the PC speakers work. You have successfully updated all the drivers. You bought a new HDMI cable, but change the cable did not help.

  The birthday Windows Update has been installed? 10 1607 Windows version. Have you tried to run the troubleshooter in Windows? Have you checked against viruses and malware? Did you run the HP Support Assistant? Here is a link to a post on answers.microsoft.com that can help. Audio HDMI 10 Windows does not? If the problem persists you can try to uninstall and reinstall the audio driver from the Device Manager.

  • Open the Device Manager
  • Click outputs and inputs
  • Right click on the speakers and uninstall
  • Restart your laptop

  If the problem persists, try using a different driver.

  • Open the Device Manager
  • Click Audio inputs and outputs to lengthen the list
  • Right-click on the speakers and click on update driver software
  • Click Browse my computer for driver software
  • Let me pick from a list of device on my computer drivers
  • Select the Audio device high definition
  • Click next and follow the prompts.

  If the problem persists, you can try a restore to when it was working properly. Computers HP - using Microsoft System Restore (Windows, 10, 8) Please let me know the results.

  Thank you! If it helps you to find a solution, please click the button "accept as Solution" down below in this message. "If you want to say 'Thank you' to my effort to help, click on the" ""Twww.Mountainview.rsb.qc.ca Up ' give me a Kudos.