Disk failure of USB storage while loading XP Pro

Similar Questions

• Installing OS on Hyper V says - we have found all disks. For a storage driver, click on load a driver.

  Hello team,

  Dell PowerEdge R610 - hardware

  Reference DELL PERC 6/1 SCSI Disk Device, think that these SAS disks.

  Question: Installed Hyper-V on the server, but when trying to install the operating system on the virtual machine, it is said: we have found all the disks. For a storage driver, click on load a driver.

  Could someone please suggest the correct load drive or where to download it.

  Kind regards

  Binu Kumar

  Hello boby

  Your question is not related to the material. Unless you use a form any direct IO to enable communication of the VM with material then the virtual machine communicates with the hypervisor.

  I suggest that you are looking for guides on the Microsoft Web site to learn how to configure a virtual machine. It seems that you did not create a data store, VHD, assigned to a virtual storage controller or one thing other storage in relation to the virtual machine.

  The problem you are experiencing is virtual.

  Thank you

• HP Pavilion 400-434 Office: intelligent control of hard disk: failure

  Hello

  It all started when the computer would go blank right after startup, the HP logo would come upward, then 'auto repair preparation", more... Just empty. After reading the forums online, I did all the possible troubleshooting steps and at the end I did the SMART test... the result was:

  Verification of the processor: past

  Intelligent control of hard disk: failure

  Failure ID: RGD7MK-7HV7RC-9XJ16K-60BB03

  After obtaining these results, when I turn on the computer, it gives me a blue screen saying: drive SMART 1 error (301) and told me to test once again, that I did and got the same result as above.

  Here is some info from the computer:

  Model: HP Pavilion slimline 400-434

  Processor type: pentium (R) of the Intel (R) J2900 @2. 41 GHz

  Thanks for your help!

  Hi there @Brugalgirl

  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, the HP experts and other members of the support staff. I understand that your computer does not start successfully, and you found a Smart Drive 301 error code. I'm happy to help you with this.

  I checked the ID of the failure, you've posted and verifies that the error. Unfortunately, this means that your hard drive needs to be replaced.  In view of the fact that the system does not boot, it is likely that the hard drive is completely unreadable, but depending on what you have on this subject, it may be worth your while to check with a local computer service shop and see if they can help to recover data from your hard drive.

  If your system is relatively new and may be covered by the warranty, or if you wish to fix with HP for the guarantee system, you can call in hotline to make these arrangements. In this case, please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Otherwise you can look at a replacement hard drive yourself. If you have a set of recovery media, then you already have a factory image HP, which allows you to put in place a new hard drive with your original operating system. If is no longer, you have a set or did not have a set of recovery media, so you can see if there are not yet available for your model.

  HP computers - get HP recovery disks or HP USB recovery disc

  Let me know if you need help most. If it solves your problem, please mark this message as a solution.

• Watch videos from a USB drive and load!

  Are there adapters that will allow me to watch videos stored on a flash drive and reload my mini ipad at the same time? Or an iDrive which has a charger passthrough

  I bought a sandisk iXpand, but when I plug the USB into the load and the iPad it charges the iPad but disconnected the Flash Player.

  The only way you can do it, as much as I know, would be to use a wifi enabled the USB stick or hard drive. Connect your iPad to the wifi signal that is generated by the player and stream the movie, while having your iPad plugged in charge.

• WNR2200 Netgear ReadyShare USB storage does not

  I have trouble getting the USB ReadyShare working on my router Netgear WNR2200 storage. If I reset the router to factory by using a paper clip and now the reset button in and then just connect a computer to Ethernet, 1 Port, it works fine and I can access by typing just "\\readyshare" in windows Explorer. Unfortunately I can not leave the router with its factory settings as it is not good for my network, I disable DHCP, because it's the 3rd router on my network. The router itself works great when I do that, all the computers connected to have a connection to the internet and can also connect to each other etc... purpose storage readyshare file sharing no longer works. It's just as if she is not there.

  While I was trying to experiment when he actually stopped working, so I reset the router to factory settings and started again. Connected to the computer first to 1 Port Ethernet and it worked fine as before. Went in the router settings and turned off DHCP and it has always worked well. It is only when I actually connect the router to other routers which ReadyShare USB storage stops working. When it is assigned an IP address from my main router which is the DHCP I guess? I don't know why that's upsetting it well? I checked on the same workgroup (a setting that I didn't notice initially) but also makes no difference.

  Does anyone have an idea what I am doing wrong? I guess it is just configured wrong and it's probably something really simple, but I can't see it. Any help would be much appreciated, thanks!

  Simon

  Change the LAN IP is affecting an IP address on the WNR2200 to be in the same range of main router.

  You will be able to change this in the LAN Setup.

  The steps would be:

  1. do you have a computer just be directly to the WNR2200 and nothing else.

  2. navigate to the router admin page.

  3. change the LAN IP to a unique IP address, such as 10.0.0.200 or one IP address that is not used in the network.

  4 disable DHCP.

  5. once the settings are saved, connect the main router to one of the WNR2200 LAN ports.

  From there, you should be able to access the USB key.

  Let me know what happens.

• USB storage, software packages and WRT610N Rev.2

  Hello!

  I have two questions about WRT610N.

  First of all. Is that a firmware update is coming for the second revision of WRT610N? It's been a while since the release of the current version. In addition, Linksys E3000 was revealed and looking into its hardware specification, it is quite same router with a bit of software update.

  And on the other hand. I wonder about the firmwares, because I have little problem with storage connected to the USB port on the router. When I use the SMB protocol to download large files, my wifi connection can be moved, and NetBIOS service was corrected (specific Windows Event Viewer). After restored connection I can't use storage via SMB until you restart. FTP protocol works without any problem, but it is not so convenient.

  It may be the problem with my laptop, but I already tried different versions of the card WiFi driver (it's Intel 3945 ABG), and I can't change my OS (it's Windows 7, and Yes, I tried to clean install). So, I really hope the new firmware or your advice. Someone at - it met similar problems?

  Sorry for my English, I'm not native and thanks in advance.

  Although Ubuntu SMB Server is much more stable and stronger, then the operating system Windows and Windows performs well when transferring file using SMS Service.

  Maybe you can try to change some of the settings on your router, if all goes well, this should help you. Change MTU size on your router for 1300 and click on save settings... Then below click on the "Advance Wireless Settings" sub-tab and below to change the interval of tag to 75, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings...

  Now, check if you are able to transfer large files from your computer to the USB storage...

• My Sony vio laptop doesn't recognize USB storage?

  My Sony vio laptop doesn't recognize USB storage?

  Is it a USB 'ding' heard when you insert the USB storage device?  If so, you then have to make right click on my computer, select manage, then disk management, look on the right side and the storage of the assign a drive letter.

• Windows 7 is no longer reads the USB storage devices

  I have a problem similar to some other posts, but different enough so that I write it here.

  When I insert a USB storage device (like a Microcenter * Go Flash) Windows 7 Ultimate just shows a yellow exclamation mark next to the device in Device Manager. OtherDevices, USB Flash drive. Software update driver fails, no update.  Uninstalling and reinstalling has no effect.

  Under properties:

  Type of device: USB FLash Drive

  Maufacturer: unknown

  Location: Port_ #0003.Hub_ #0008

  Pilot wrote:

  Privder: unknown

  DAT: Not available

  Version: Not available

  digital GIS: dig signed ot

  Under Details:

  Hardware ID: USB\VID_1307 & PID_0163 & REV_0100

  USB\VID_1307 & PID_0163

  There is no ping, no popup. Nothing. All this used to work very well, and now, when I need to copy files to work urgrnetly, he's dead.

  Just rub a little salt, I CAN access the device through Linux in VMWare Workstation. But when vmware is not current execution, or when I disconnect and try to attach to host, nothing happens.

  I tried each storage device USB I can find and no luck on any of them.

  Thank you

  TMB

  After digging through the forums, I tried to copy the usbstor.inf and .pnf to the Windows\inf directory and reinstalled the driver through the Device Manager, and it loaded right up.

  I don't know, but I suspect that the impact of this change, there are other devices that can complain. For now, the process of transfer between W7 and VMWARE/linux seems flawless.

  TMB - back

• Single RAID 5 disk failure, bad start

  I have a T110 / Perc s100 / Raid 5 (3 discs). Ctrl-R shows deteriorating table, single disk failure/off line.
  Server 2003 seems to boot normally, instead results in a blank screen with the mouse arrow to work in normal mode and safe.  Is a reconstruction of the still picture once I replace part even not. HARD DRIVE? Is the bad boot due to the degraded range?

  You could use the Dell installation utilities, that might have loaded the appropriate drivers for you. You cannot use this process here. I suggest you nLiteOS.com.

• Impossible to fill out the case of the composer from vm - hot add disk failure

  I'm checking a pool of composer, but the extraction fails with the error to the user saying "no server available for this transfer.

  and the connection to the server has the following sequence of warnings in the application log

  EventID 104: No server available transfer to transfer VMS/datacenter/PathtoVM/PoolDesktopVM not name Session: SessionIDString

  EventID 104: Session: SessionIDString reason no. ready transfer servers have access to storage for the VM me: vm-xxxx disk key: 1234

  EventID 104: Session: hot SessionIDString add to the user disk failure: username desktopDn:CN = name of the PoolDesktopVM

  The snapshot that depends on the pool has been published on the forwarding server and comes to 2.9 GB. He could not be connected, but the extraction of the VM based on that snap fails 3.0 GB on the 3.7 GB the customer view says he has to download

  The virtual machine with the snapshot is windows XPSP3 on hardware v7 with vmdk stocked thickness 1.

  The composer generated obtained vm controller buslogic scsi parallel and 3 thin provisioned vmdk added to chain SCSI 1 to account for the persistent drive of the composer and the disposable disc over the virtual machine swap file.

  The composer added 3 discs would explain the remaining space, that the customer has left to check.

  The forwarding server is hardwarev7 using the parallel scsi controller free such as recommended in the view 4.6 installation guide

  Can someone help get beyond the hot disk failure add that seems to be triggered when (I guess as the forwarding server) tried to mount?

  Hello

  It is a requirement. Transfer server THAT VM needs to access the desktop under transfer disks. in other words, host th transfer server running vm must be able to access disks of office under body.

  -noble

• VMware ESXi 3.5 U3 Installation hangs while "loading module ide."

  Hello.

  I tried to install ESXi on a server (motherboard: Supermicro P4SDA;) Processor: Pentium 4; 3 x HDD: Samsung SP0411N & 2 x WD 400BB) and installation stops while loading add-on ide...  And that's it, no error messages - nothing.

  How can I get rid of this problem?

  Thank you!

  Had a similar problem on a box.  He had a problem with the onboard IDE drive.

  Disabled the onboard IDE and a USB DVD drive to install ESXi.

  Not sure if this will help, but the suggestion that' her.

  Jase McCarty

  http://www.jasemccarty.com

  Co-author of VMware ESX Essentials in the virtual data center

  (ISBN:1420070274) Auerbach

  _{Please consider awarding points if this post was helpful or appropriate}

  

• VMware ESXi 3.5 U3 Installation hangs while "loading module sata_svw.

  I tried to install ESXi on a DELL 2970 with PERC 5 / i and the installation stops while loading module sata_svw...

  the last entry in the log of the kernel is:

  WARNING: LinSCSI: 3494 driver didn't scsi_done of its abort handler and yet he returned SUCCESS

  How can I get rid of this problem?

  Thank you!

  Hello

  had the same problem, its clearly the sata on the PE2970 :_| device.

  If you turn off (both) controller sata in BIOS Setup will work. Pretty sad: you won't miss your CD-Rom I drive so I used a USB CD-ROM for installalation.

  I know that this is only a workaround, cause I need the CD of shortcut for the guest computers, but I hope that there will be an update of the driver soon.

  Respect of

  Thomas

• In e-mails AOL, verification of the individual messages in the results of regular system in this error message: there was an error while loading the message. Please try again later.

  In access to AOL e-mail via the full version, I can navigate my account (old messages, new messages, spam, etc.) very well, but when I try to open an individual email, I get this error message: "there was an error while loading the message. Please try again later. »

  This is identical to a problem someone else was described in another thread... Unfortunately, nothing suggested you him seemed to work. I have BEEN cheated at the opening of a file attached to an e-mail immediately before this started, so I think it's a virus or something. IN ANY CASE... I AM able to open the messages when I use the basic version of AOL. Initially, the problem seemed to be in Firefox, but I tried with Internet Explorer now also and it's the same thing, and the basic version is accessible while the full version is still blocked.

  On both browsers, after the error message, I can't even click on individual posts to TRY to open another, and there are a few not-very-right boxes and the x and the things that appear on the screen that do not belong.

  Please tell me that you can not do that, go away... I tried uninstalling and reinstalling... Firefox who did not. I also enjoy McAffee, and that has not changed anything.

  You can do a check of malware with several digitization programs of malicious software on the Windows computer.
  
  Please scan with all programs, because each program detects a different malicious program.
  
  All of these programs have free versions.

  Make sure that you update each program to get the latest version of their databases before scanning.

  • Malwarebytes' Anti-Malware:
    http://www.Malwarebytes.org/MBAM.php
  • AdwCleaner:
    http://www.bleepingcomputer.com/download/adwcleaner/
    http://www.Softpedia.com/get/antivirus/removal-tools/AdwCleaner.shtml
  • SuperAntispyware:
    http://www.SUPERAntiSpyware.com/
  • Microsoft security scanner:
    http://www.Microsoft.com/security/scanner/en-us/default.aspx
  • Windows Defender:
    http://Windows.Microsoft.com/en-us/Windows/using-Defender
  • Spybot Search & Destroy:
    http://www.safer-networking.org/en/index.html
  • Kasperky free Security Scan:
    http://www.Kaspersky.com/security-scan

  Alternatively, you can write a check for an infection rootkit TDSSKiller.

  • Utility anti-rootkit TDSSKiller:
    http://support.Kaspersky.com/5350?El=88446

  See also:

  • "Spyware on Windows": http://kb.mozillazine.org/Popups_not_blocked

• Is there an advantage to having a backup disk image of Macintosh HD (for MacBook Pro) to ease/speed of recovery after a disk failure rather than using Time Machine to recover?

  I'm trying to understand the best way to prepare for the recovery of a failure in the drive for a MacBook Pro.

  I do not understand the nuances of the time Machine - I know from personal experience that it is a recovery tool great when your existing drive is intact and you're just trying to restore a file.  But what happens if the drive has a hardware failure and needs to be replaced?

  Is there an advantage to take periodic images of Macintosh HD for quick recovery (and then using the incremental backups Time Machine to catch up to the current position).  Or Time Machine may facilitate a recovery in case of failure of the disc just as easily/quickly that will give it to have a separate image backup?

  Thanks in advance for your help.

  YES!.  If you have a clone boot disk, you can either connect it to a MBP or Exchange it with the internal HDD failed and be back in business quickly.  Time machine, as good as is, can take several hours to restore your system, depending on the amount of data.

  For cloning, I recommend Carbon Copy Cloner.  It is not free, but it's worth the price:

  https://Bombich.com/

  I use it in conjunction with Time Machine.  (two backups are better than one)

  Ciao.

• is it OK to use your macbook while loading

  is it OK to use your macbook while loading

  Yes.