Display connection to sbrio 9607 amulet

Similar Questions

• Connect the sbRIO amulet monitor

  I have programmed my amulet display and have a VI RT on my 9636 sbRIO which must communicate with the amulet.  I have the amulet the sbRIO-related uses the USB port.   I also installed the software on my sbRIO:

  (1) NI-VISA 15.0.0

  (2) passport OR VISA-USB 15.0.0

  When I run the RT.VI, it is not the USB port on the sbRIO.  I guess I'm missing some software on the sbRIO but can not understand.

  Thank you

  Craig,

  To dispel confusion, you shouldn't see your amulet device in MAX, you should see the sbRIO. In addition, you cannot communicate via USB between the sbRIO and amulet device, but you can communicate over the serial (RS232).

  You are right in saying that you are missing on the sbRIO software because there is not a driver for the sbRIO use USB.

• sbRIO-9607

  Hello

  I use sbrio 9607. I connect the NI 9234 module to sbrio by jury NI 9697 CTMR which has two slots. The problem is I don't need a second slot and slot increases the size and volume.

  (1) is there a version of unique slot 9697 OR?

  (2) is there a way to connect the NI 9234 to sbrio?

  Thanks in advance,

  Gear

  tetego wrote:

  Hi Matt,

  Is it possible to use a RMC connector

  and isolate the appropriate pins to connect through Connector D - SUB 15-pin for the NI 9234?

  Thank you

  Gear

  It turns out that my previous statement was somewhat inaccurate (should have read the documentation more closely).

  We do not have an EGGA which allows you to use only a single module C series, but you are able to create your own CTMR which would only have one connection of module C-Series.  The link below explains how you can make this connection.  The important caveat is that you will not be able to use the pins previously used for the second module for other tasks, because it is a signal of fixed behavior.  If you want to save space, it can be done, but if you want more connections DIO it is impossible.

  http://www.NI.com/PDF/manuals/375536a.PDF#page=18

  I hope that summarizes the options available.

• Two external displays connected to my dock and my ThinkPad T450

  I have two external displays connected to my dock and my ThinkPad T450.
  Everything works fine, when suddenly the monitor LEN LT2223pwC (using DP cable) goes into energy saving mode during use and there is not up to come back/wake, only to turn it off and back on
  This Setup worked very well with my office. For some reason any the monitor does not receive the signal from the laptop / docking station.

  I got a new docking station and solved the problem. Thank you

• Attempt to add a "new target or device', but the sbRIO 9607 is not listed

  Hello

  Just upgraded to 2015 LabVIEW and CompactRIO 15.0.

  Also used the Service to update OR install the patches for 2015 of LabVIEW and CompactRIO device drivers.

  I'm trying to add a target in LabVIEW in the window "add targets and devices." I select 'new target or device' and develop the sbRIO options. I see a lot of targets, but unfortunately the sbRIO-9607 does not appear. It simply isn't.

  

  Thoughts? When I'm back in the office on Monday, I'll try a repair of the driver.

  Best,

  Dan

  Well, this is embarrassing, but I don't know I'm not the first and won't be the last to commit this error.

  I had accidentally opened LabVIEW 2014 SP1 instead of 2015 of LabVIEW.

  Of course, it works in 2015 from LabVIEW. Congratulations if you guessed this might be the problem.

• My laptop connects is more to the internet, either hard wired or wireless. When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.

  My laptop connects is more to the internet, either hard wired or wireless.  When it is hard wired, the laptop displays connection but I can't access the internet, and I've done it before.  My other computer has service very well (or I wouldn't send this message) I checked everything, what to do?

  original title: internet connection.

  Hi vonhatten,

  1. Did you the latest changes on the computer?
  2. You receive an error message when you try to connect to the internet?
  3. You have security software installed on the computer?

  Refer to the article below and try the steps mentioned, check if it helps.

  In Windows network connection issues

  http://support.Microsoft.com/kb/313242

• MacBook pro screen flashing external display connection

  Whenever I connect a display remotely on DVI (tried both Apple DVI-> Adapter Mini DisplayPort customized DVI-> HDMI adapter), my Macbook pro display blinks for a long time, like 1-2 minutes before you succeed. This does not happen with VGA (I tried Apple VGA-> Mini DisplayPort adapter). He is shown here:

  https://www.YouTube.com/watch?v=dLmI82DDvXw

  It's annoying as *. For example: whenever I visit the coffee machine or the bathroom, I have to wait 1-2 minutes until I can get back to work, because the screen was turned off until I can come back. And don't suggest me to extend the period of closure, which is not a viable solution. It happens every morning so when I get to work and turn on the computer.

  Any help would be greatly appreciated!

  See you soon

  Hi ColonelKermit,

  I understand that you have a problem with your screen when attaching it to an external monitor. You can try to fix it by resetting your NVRAM memory on your computer, which is explained in the following article:

  How to reset the NVRAM on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204063

  You can also start your computer Safe Mode, which can help to influence the situation:

  Try safe mode if your Mac does not end commissioning - Apple Support

  https://support.Apple.com/en-us/HT201262

  Thanks for being a part of the communities of Apple Support!

• System hangs on the external display connection

  I just bought a MacBook Pro 13 "mid 2012 version because I travel a lot." I do a lot of coding on my main PC. I didn't mind having a smaller screen and the retina no since I had to plug my monitor 27 "HD for the majority of my work. This is the problem...

  Two things happen when I try to connect it via Apple's Thunderbolt at the VGA connector. Or the other

  1. the external screen but the MBP 2012 (1200 x 800) native resolution and I can't change it at all

  or

  2. all of the gray system out and crashes and the second monitor turns off say there is no entry. Then I pressed the power button to turn off completely it.

  Nothing wrong with the display or the adapter I tested them both on another laptop that my wife and my main development office (two PCs). I guess that something is wrong with the MacBook or the underlying software. I'm running El Capitan and the MBP is maxed out in RAM and a 500 GB SSD. I tried a lot of things I've seen online already, but none of them worked. Is this what can I do to get the 2nd screen to work on its 1920 x 1080 resolution?

  Have you tried the PRAM reset?

  How to reset the NVRAM on your Mac - Apple Support

• ZBook 17 G3: Premature sleep during outdoor display connected

  Hello

  I'm using the default settings in the power and sleep settings. The laptop is plugged into a power outlet. It is plugged into the docking station of love at first sight with the mouse, the keyboard and the ethernet connected. The screen is supposed to turn off after 10 minutes and the computer is supposed to sleep after 30 minutes of inactivity. It I do not connect an external monitor, everthing works fine.

  If I connect a HP27sv monitor to an HP DisplayPort-to-DVI adapter and plug the docking station, and then I get the following behavior. After a reboot, everthing works fine until the first time that the computer sleeps: the display turns off after 10 minutes and wakes up in fine. After 30 minutes, the computer goes to sleep.  However, once the computer woke up from sleep mode, then it still comes down to sleep after two minutes. No matter what I do with the power settings and sleep, the computer goes into sleep mode after two minutes of inactivity.

  I can also reproduce the bug by using the sleep on the keyboard button:

  • Connect the external monitor
  • Press standby on the keyboard, the computer goes to sleep
  • Wake up computer and connect
  • Wait two minutes without activity, the computer goes to sleep again (should be 30 minutes of waiting)

  This system has the NVidia Quadro M1000M graphics card for the display docking station ports. Version of the NVidia driver is 354.86

  Hello

  There was a un communique release lately for the firmware of lightning, see support of your site and install it.

  Also, here is the link of all possible problems and solutions for love at first sight. http://WWW8.HP.com/h20195/v2/GetPDF.aspx/4AA6-5088EEW.PDF

  Thank you...

• W520 gets stuck on Thinkpad with a hard drive external display connected

  Hello world

  I just changed from an external hard drive of 500 GB to 3 to one, but if I leave that new connected for starting my computer the computer crashes to the thinkpad logo and launch startup.

  The boot order is set to boot from the internal hard drive before the media CD or USB, so I don't know why it is the way.

  I have no problem with my original external hard drive connected.

  This isn't a huge problem, just a downside I want to turn on my computer, wait 30 seconds, going ' Oh shoot, on the right, "have to disconnect the drive, and then restart.

  Thanks for any help!

  gtlane wrote:

  Hello world

  I just changed from an external hard drive of 500 GB to 3 to one, but if I leave that new connected for starting my computer the computer crashes to the thinkpad logo and launch startup.

  The boot order is set to boot from the internal hard drive before the media CD or USB, so I don't know why it is the way.

  I have no problem with my original external hard drive connected.

  This isn't a huge problem, just a downside I want to turn on my computer, wait 30 seconds, going ' Oh shoot, on the right, "have to disconnect the drive, and then restart.

  Thanks for any help!

  What level of BIOS are you running on the W520 and what external HARD drive brand? BIOS 1.38 was supposed to fix the POST with the 3 TB drive plugged into the USB 3.0 port. Please report back.

• My laptop displays connect to WIFI but doesn't connect and lists of unidentified network

  I use Vista on my laptop and recently changed my Netgear WIFI bridge.  I added the bridge, but when I go to connect it says connected but not connecting, and lists of Undentified Network.  I googled this problem and cannot find a solution.

  Hello

  1. you get any error message?

  Please follow the steps from the link below.

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Also check out the links below.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-finding-wireless-networks

• Wireless connectivity problems: Windows Vista displays connected to the internet with good signal, but cannot access the internet more than a few seconds.

  Hello

  Recently, I brought a Dell with Windows Vista and a Belkin Wireless adapter in my house somewhere else. The computer has never had problems connecting to wireless internet on the other networks, however since the move I was not able to access the internet. Sometimes the network shows only a local connection and not Internet and other times, the network has a strong signal, a network identified and even an internet connection, but when I open any browser, it is only able to load the Google homepage and I cannot navigate anywhere else. I turned off all firewalls and even uninstalled all 3rd party software protection. I checked all my browser settings and made sure they detect automatically the IP settings and proxy settings. In other words everything seems in good shape, but I still have no navigation capability. Any ideas?

  It turns out that I had to remove all the old Wireless USB software that had been used previously (there had been other versions of Belkin and Linksys). I then used the computer from my friend to download suitable driver on the Belkin site for the internet adapter USB I used and BAM.

• "There no external display connected.

  This message came suddenly on the screen and won't go away, even if I rebooted several times. It rises on the top of each window, and it is disturbing. What should I do to make it go away?

  Hi JI,.

  Thanks for the reply and sorry to hear about the inconvenience caused.

  This problem may be due to corrupted display drivers.

  I suggest you to uninstall display drivers and restart the computer.

  Please refer to the article that will help you to uninstall devices by using Device Manager:

  https://msdn.Microsoft.com/en-us/library/Windows/hardware/ff553572 (v = vs. 85) .aspx

  Once the drivers are uninstalled, restart the computer and check if that helps.

  Hope this helps, for assistance please answer.

• No sound on external display connected by HDMI win7 premium 64-bit running Notepad

  Previously on vista I had no problem. its available on external monitor connected HDMI
  Cannot find any control in win 7 to switch on the sound computer monitor HDMI

  Hello rbh111,

  Thank you for visiting the Microsoft answers Site.

  To better help, what is the brand and model of your PC?

  Also, try clicking on Show disconnected devices and see the disabled devices under the noise>reading tab and make sure that output HDMI device option.

  If the HDMI option is not listed, you can check that the last audio device driver Windows 7 and Windows 7 video card driver provided by the manufacturer of the PC are installed and then check the issue.

  Please let us know if the steps above help you to solve the problem for you.

  Thank you

  Mary
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to connect to Internet even though Wi - fi displays connected

  connection WiFi listed as 'connected', have always failed to connect to the internet.

  Hello Sylvie.

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the issue.

  This problem may occur because of corrupted network drivers or incorrect network settings.

  I would suggest trying the following methods and check if it helps.

  Method 1:
  Run troubleshooting network adapter and check. Please follow these steps:

  a. press Windows + C keys together, click Search, type Troubleshooting in the search box and click on it in the search results.

  b. click on 'show all' and then click 'network card'.

  c. click 'Next' and follow the on-screen instructions.

  If this does not help, use method 2.

  Method 2:
  Use the steps described in this article and check the issue.
  Reference:
  Wireless and wired network problems
  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-81&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  I hope this information helps.

  Please let us know if you need more help.

  Thank you