disruptive shutdown

Similar Questions

• Satellite Pro A200 (PSAF4A) - HARD drive stops and the computer crashes

  Hello

  It's my first post in this forum, but certainly not my first issue

  I recently had to re - install Windows Vista on my laptop because I had an undetectable virus that attacked Windows and made him useless.
  Before that, I had many, many startup errors and windows crashes, but which were preventable or fixable. After the re - install, I noticed that windows stability was much better until recently.

  I have not changed the settings or anything what so ever on my computer laptop which could affect the performance somehow, but I have a new problem.

  If I have my computer running, performing tasks of base for a few hours I notice that performance and all of a sudden my computer completely stops responding.
  The disk shows no signs of life after this point, and his only solution is a "disruptive Shutdown.
  This appears in the reliability monitor and performance that all this, there is no input error, and nothing is done after.

  I also noticed if either windows defender or other my antivirus runs a system scan that my performance is reduced to the point where I can't run a simple task like opening an Explorer window. This also translates to total non-response. This never happened before a week ago and now it happens every time.

  These two started within the past few days and there is no clear reasoning behind it. My inactivity of the processor is always the same, no new processors added and no settings changed.

  This could be a problem with Windows, my HARD drive, my CPU or something worse?

  Is there a reason why is happening and is there a solution either of these problems?

  First of all, you reinstall Windows with the Toshiba recovery disc or disc of Microsoft?

  It's strange and not easy to say what's wrong, but in your case I would test the RAM and HARD drive.

  There are special tools to test the following:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  http://Memtest86.com/

  On the two Web site, you can download a CD image. Burn it to a CD, start with him and then you can test parts.

  Good luck!

• CoreTelephony error in trace file as a file for coretelephony tracing operation has failed, perhaps you need more disk space. Details "error opening the file/tmp/ct.shutdown, err = operation not permitted

  I got this error:

  "CoreTelephony Trace file error
  A file for CoreTelephony tracing operation failed, you might run out of disk space. Details "error opening the file/tmp/ct.shutdown, err = operation not permitted"

  I tried to solve it by searching for CoreTelephony errors. Could not resolve yet.
  Software does not, especially of photoshop...

  Any ideas?

  Same thing here, iMac with OS X 10.11.6. All started a couple days ago. Have not found any valid solution online yet, I tried rebooting in recovery mode and check disk, but it seems that everything is ok with the drives and permissions.

• macOS Sierra can fully shutdown

  Hi, yesterday I just upgrade my MacBook Pro for macOS Sierra, when I shut down my computer, it can close all the application and turn my screen in the dark, but my apple macbook light logo still on. I have to press and hold the power button to shutdown entirely. Can you suggest me a solution for this problem?

  Thank you!

  It is possible that your Mac is always indexing of files for Spotlight.

• No restart or shutdown Sierra

  I upgraded my MBP (mid-2015) to Sierra yesterday and now its not shut down or restart properly. Its get stuck on the black screen with nothing on it (not even a cursor). The display lights stays ON but nothing really from there, I even left there like that for more than 20 minutes. I Force shutdown by pressing the power button / stop for a few seconds.

  Step 1. Reset a SMC; Reset the management system (SCM) controller on your Mac - Apple Support

  Step 2. Reset the PRAM but keep P-R-Opt-Cmd when you start. The MBP sounds once again, how you can release the keys.

  Step 3. make a start by holding down the SHIFT key until you see the progress bar. Once you get to the login screen, you will see "Safe Boot" in red next to the clock.

  Step 4. Reboot again and log in normally.

• After the upgrade to sierra, shutdown is extremely slow

  stop takes about 5 to 7 minutes. Screen will Dim, computer does not respond, but the stop takes 5-7 minutes. In the system log, no problems are reported.

  I closed all the software running before shutdown (clamx-av, dropbox, owncloud), but no difference.

  Hi rmschaefer,

  Thanks for the upgrade to Mac OS Sierra! Looks like your Mac takes a bit longer at the right stop. Great way to make sure that all applications are closed before you stop. You can try to check your Mac logs or startup items. Your item journal are applications that run as soon as you start up your Mac. They can run in the background continuously slow down your machine. Sierra macOS: If you think you have incompatible connection points

  You can also check to see how much disk space you have on your Mac. With Mac OS Sierra, you can release and optimize your disk without effort space to allow your Mac to run to its full potential!  Information System for Mac: optimization of the storage on your Mac

  If the release of disk space on your Mac and the removal of the login items not solve the problem, try to start the Mac in Mode safe.  Try safe mode if your Mac does not start-up
  
  

  What is safe mode?

  Safe mode (sometimes called secure boot) is a way to start up your Mac so that it performs certain checks and prevents certain software from loading automatically or opening. From your Mac in safe mode does the following:
  Check your startup disk and attempts to fix problems if necessary directory
  Loads needed kernel extensions only
  Prevents elements start and the login items open automatically
  Disables the user installed fonts
  Delete font caches, hiding the kernel and other files of the system cache
  Together, these changes can help resolve or isolate issues related to your startup disk.

  These measures should have your Mac off normally as expected and the Mac OS Sierra also runs fluid it is supposed to. Please use the Apple Support communities to post your question.
  Good day.

• Does not meet a request to shutdown or restart

  MacBook Pro retina, 15-inch, late 2013 2.3 GHz Intel Core i7 running OS El Capitan worm 10.11.6, it fails to respond to a request in the Apple menu to stop or restart.  I checked to see if all programs work always stop preventive action.  the only way to stop the mac is to hold down the power button and force a shutdown.

  Clues?

  Reset the SMC and the MVRAM:

  https://support.Apple.com/en-us/HT201295

  https://support.Apple.com/en-us/HT204063

  Any change?

  Ciao.

• MacBook shutdown

  When I confirm my macbook stopped can I close just the cover or what I should expect that the keyboard light? and both will result the MacBook at the stop or closing the lid will to sleep instead of shutdown?

  Hello

  With El Capitan 10.11.6, I have to wait until the keyboard lights turn off and give about a minute or two before closing the lid. It takes a little more for some reason any for a full stop. I learned to confirm the stop and walk. Come back and close the cover later. Weird, but I don't let it bother me. Come to work with her.

  Bravo!

• Disruption of the page

  Disruption of the page
  I see a cluttered pages.
  I disabled the plugin and the extetion, but my problem is not solved.
  http://picpaste.com/11-01-2013_09-07-48___-__-3TYSaaI1.PNG
  (I am currently using the new private window that does not have this problem)

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• iCloud disrupts the Internet connection

  I had a lot of power outages Internet randomly and finally isolated the problem to my backups iCloud iOS devices and/or iCloud photo library will be mailed.

  (3 iPhones and iPads 4) devices are connected to a wireless router (currently a Netgear WNDR4300v2) and work perfectly well throughout the day. Only when I plug in a device to load the fact so disrupt the router's Internet connection. As expected, the devices to begin with iCloud download when they are connected to the load.

  I tried 3 different routers and you experience this problem on all of them. As soon as the device (iPhone or iPad) tries to download to iCloud, the Internet stops almost completely. I can ping from a laptop ethernet-cable-connected, but it is extremely slow and cut in half the packages. I can still connect wirelessly to the router and to interact with its administration interface, but the connection Internet is basically dead until I have unplug the iDevice download from the network or unplug it (which disables the backup iCloud).

  An iPhone 6 especially cause the majority of the question because I take a lot of pictures with her (she also monthly extra storage iCloud add-on). Other devices have also caused disturbances, but those who don't last as long. I tried to set many different parameters and frequencies on my routers, but nothing is done even a little.

  Is this the iPhone 6 with lots of photos have also OPTIMIZED enabled?

  It's a lot of traffic from router. If you optimize the phone and iCloud communicate constantly that the phone downloads new photos and iCloud analysis local storage of the phone, sending new files optimized down to the phone based on the amount of space on the phone. It can choke the warmest router.

  Then add the traffic from day to day and other devices...

• When I try to shut down my computer with Firefox running it hangs and stops the shutdown process.

  When I try to shut down my computer with Firefox running, it does not close properly during the closing. Instead, it crashes (as described in this article) and will continue to do so until I have stop the shutdown process and close it manually, where it will still not respond. There is the substantive issue. Here is the list of the relevant data to identify more precisely:

  On the list of programs is still active during the closure, the window of Firefox starts only appearing once as it should be, but a few seconds after starting to hang, it begins to appear a second time on the bottom of the list, with the specific name of the page is a duplicate of whatever it is on the original.

  This problem does not occur in safe mode, but it is not caused by one of my addons either, as I figured out after disabling all my addons with tools > Modules rather than the safe mode and still the problem.

  He is listed as that passes several times a week, but that is simply because that's how many times I forgot to close Firefox before pressing 'closed' and leaves the room without bothering to check it works. It happens whenever I try to turn off the computer with Firefox is running well.

  See this article--> occurs not in Safe Mode

  Check and say whether his work after turning off hardware acceleration.

• Satellite Pro R50 - B Series 10 Windows shutdown problems

  Hi out there!

  I wanted to just inform you on an enoying but reproducible BUG:

  Toshiba Satellite Pro R50 - B series:

  You must disable the Intel Management Interface in the Device Manager in the contrary case, the computer laptop didn't shutdown completely / Standbymode will not work.

  Question (Bios V1.4 - Intel ME 11.00.1166):

  Work more than 30 min. then try closing. Screen goes blank - but the LED on the stay before the fan stays on until the battery is completely discharged. Or try to go to sleep mode. Even the stop.

  Just disable Intel ME Manager of year Windows devices you fine.

  Waiting to hear from Toshiba - I m a reseller, so the same problem exists on > 10 notebooks here.

  Best regards, Bernhard

  Hi, I have exactly the same problem with my Satellite Pro R50 and Windows 10.
  Just installed the updated Toshiba Win10 drivers, but not a solution.
  Help, please!
  Best regards, Oliver

  EDIT: SOLUTION

  https://Forum.Toshiba.EU/showthread.php?81944

• Delayed start, shutdown procedure

  I recently discovered that my beautiful satellite pro has developed a resistance to be shutdwn or restarted. Through the usual procedure is very slow. Start at the stop is ok, but to get the final options (box with restart, shutdown, is slow). No info on Google.

  Explorer is faster than ever. I defragged, cleaned, checked for viruses, checked with systemworks, and everything is ok.

  Windows 2000 and I am on the network with the XP computer.

  The only other issue, since the definition to the network, is a tendency to lose the settings of the printer (against printer, references on not installed, although exclamation points that it works.) Printer is local and not on the network).

  Any ideas would be welcome. It's a little scary, because he had control with Toshiba upward only a few weeks ago. The flaw with the stop developed after that. They recommend a complete reinstallation, of course.

  Hi ellen,.

  like the guys from toshiba, I suggest you reinstall, too. After a while, an operating system becomes slower and slower due to misconfigured setting (no matter what settings) and the
  Register to become more complete, and the system can make really weird things.

  Thus, it would be good to backup you important data and reinstall windows with the recovery cd. After that, you should have somewhere clean and sober (from 3rd party software) system.
  Would appreciate feedback if you do reinstall.

  Welcome them

• Satellite L850-E8S - shutdown problems

  Hello everyone

  I bought Toshiba Satellite L850-E8S with Windows 8.0 (for a single language) preinstalled in October 2013. At the moment I can't get stop normally.

  Question: * pressing Shutdown (stop) of charms goes up "Windows is shutting down" and after that the screen turns off but power light is lit and the fan keeps operate.* I stop it by pressing the power button, I really want to quit smoking. (Once I didn't notice that and put the laptop in a bag for a few hours and it of a miracle that no equipment would have been burnt, despite the laptop was hot like the Sun) * the problem started after a month of use, and I didn't think her yet.*

  First of all, I thought that the case concerns him * hybrid Shutdown in the Win8. I have visited many forums dedicated for hybrid stop, proven fruitless discussions. *! AND! I had the same problem on my laptop with a slight difference - loading Win7 and Linux * the monitor stays on (with the lights and the fan on either). *
  Moreover, I also saw a BSOD after a day I bought the laptop. This problem concerned Realtek Audio driver and SRS Premium sound. As I understood the question is drivers conflict. Right now I have no installed Audio SRS premium and see no BSOD, but Realtek audio driver is not stable: the sound either begins to work in a few minutes after starting windows or it does'nt work at all.

  First of all, I wish really that someone to help me with the shutdown problem. All tips are welcome.

  Hello

  Check it please http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm, change the settings described and try to turn off your computer is turned on on a regular basis.

  It works for you?

• Tecra Z50-to-17 t constantly freezes during shutdown

  My new Toshiba Tecra Z50-to-17 t constantly crashes on shutdown.

  At first I thought that it could connect to the Cisco all lie, as it appeared in the event viewer several times.
  After I deleted it went well for a while, but now the problem occurred again, but this time there is nothing to see in the event viewer.

  Can someone help me what is wrong and how can I fix it myself?

  Hi friendly smirou

  The laptop has been preloaded with Win 7 64 bit system.
  I guess that you are still using this system, I would recommend you to repair the system using the windows have auto repair function.

  Start Notepad, and then press F8.
  Now you should be able to access the Advanced menu.
  Here, you can choose between different options.

  You can choose the last known good configuration option.
  You can also choose the first option to fix your computer, which will open the next window, where you can access the Startup Repair feature.
  There, you might choose the Startup Repair option

  Otherwise, it would be desirable to recover the computer laptop back to settings factory just to check if its a system single or maybe hardware problem related question