Dotted lines of white on the printed work of InDesign.

Similar Questions

• Printer Dell 1100 printed in white when I am on the internet and I want to print any page. The printer works in the office.

  Printer Dell 1100 printed in white when I am on the internet and I want to print any page. The printer works in the office.

  I need help please

  If it is printed in white on white paper how you see it?

  Check your printers settings in his program in place.

• OfficeJet 8500 more scanner not found, the printer works fine. Windows 7 Ultimate 64 bit

  I had to remove the drivers and the software once.  I have re-installed, but now the printer works fine and when I try to run a scan of the computer or the printer they don't know each other and I can't scan.

  It fixed...  I had asked a computer specialist to look at and he cheated by creating IP port and tell the PC to print via the port.  Although the sweep of the network was suspended on that port.  Installed the printer via a USB cable and then removed from the printer and reomved first which stood on the IP port.  Once it is I installed the printer again and scan network found the printer immediately and went big.

• I have a Dell V305 printer scanner. The printer works fine. When I try to scan it says list of applications to download and then he said: it couldn't download the list. I don't know what to do.

  I tried everything to make it work. Reference Dell wanted to charge me 234.00 for them correct errors on my computer where the printer does not respond to my computer. I don't have a disk for the printer when you purchase my system. I restored to factory default and now the printer works fine. All windows updates are made. But somethis does not go with the scanner. Please someone help me!

  Update to the latest version of the driver: http://www.dell.com/support/drivers/us/en/04/DriverDetails/DriverFileFormats?DriverId=R264821&FileId=2731112408

  and the latest firmware: http://www.dell.com/support/drivers/us/en/04/DriverDetails/DriverFileFormats?DriverId=R205586&FileId=2731123538

  can help.

• HP Officejet Pro 8500 best has come out very low but the printer works fine.

  I was always able to make great copies.  The quality of the document that I copy is excellent and I've copied before.  Now everything I copy is very low and cannot be read.  The printer works without any problem.

  Hey 1265yankee,

  I see that you have a problem of quality of the copy with your Officejet Pro 8500 (A910) a model-all-in-one.  Have you tried to reset the printer hard and ensured that the device is connected to a wall outlet directly?

  • Unplug the printer while on
  • Unplug the other end of the power cord from the wall jack directly
  • Wait 30 to 60 seconds
  • Plug the unit back to

  Also, take a look at the steps in the document found here.  The document is not directly applicable in the present case, but the steps are the same for your question.

  Let me know how it goes.  If this does not solve your problem, then I have the steps to perform a factory reset on this product to see if an internal reset will be able to get the device to work as expected.

• How to check if the printer works.

  They gave me printet 720C en with empty cartridges. I connected the printer. But when I try to print nothing happens. Not at least the paper to go so I can see if the printer works? I do not like to spend money for the ink and then discover the printer does not work.

  VDV

  OK, some are progressing.  The Red blinking light may indicate a number of things, but printing will not happen in this case.  I would start by clean cartrdige contacts, as shown here.

  If that does not solve the problem then see the page here.

  There is not low on ink or another indicator for the Deskjet 720 that could prevent printing (or at least going through the motions) with a cartridge empty.  The printer does an electric test of cartridges before printing to that there are no problems might damage the printer control electronics.  The printer will also check and make sure that the cartridges are installed, this model cannot work without both cartridges.

• Dotted lines do not meet the size on the print

  Hi, I have a big problem with my design and the dotted lines with inDesign, maybe one of you can help me ^_^

  I have a lot of dotted lines in my design and in the inDesign I see perfect, they fit perfectly with the margins. But when I print the document that the dotted lines do not correspond, I send you an example, the continuous line have the same width as the dotted line.

  

  Thank you very much

  Did you also use step and repeat for the duplicate lines or draw each individually? You must be the step and repeat for consistency.

  That said, I think that a better way to handle this would be to use notes on withdrawal right tabs. Use a block of text and set the text leading to the spacing that you want (or set up a reference with this spacing grid and set the paragraph style to align with the grid). Press SHIFT + Tab to create the first withdrawal right tab, then Enter and Shift + Tab for each additional line. Create a character Style with a dash of personalized using your style dotted underline and apply it to the tabs.

• Must press paper to get the printer working properly

  Printing problems...

  When we print from any computer on our P2035N printer must press the paper button so that it can work. Also, it will not print page 3 of one of our computers, he jumps just this page.  We have replaced with a new printer... even one and it has the same problem.

  Ask technical questions in the forum Feedback is useless, so I moved your post to the windows 'Hardware and drivers' forum.  Always include your version of Windows when you post.

  Messages displayed on the front panel of the printer?  This looks to me to an incompatibility between the paper type settings in the driver and the default type of paper in the printer and the printer is waiting for the type of paper correwct to load.  You say by pressing the button on the printer, the printer to use whatever paper is already loaded.  It could also be a mismatch of paper tray, with the pilot, indicating the printer to use a Board that is not loaded, or which does not match the default tray set in the printer.

• How to make the printer work with the new Windows 7 laptop?

  can someone me please help... my printer is windows xp and I just got a computer laptop windows 7, how can I make my printer work with my laptop!

  Thank you
  need help with my printer

  Hi gingerbabe001,

  To set up and install your printer, see the link below.

  http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_task=setupCategory&cc=us&DLC=en&LC=en&OS=4062&product=1153754&sw_lang

  Good luck.

• Internet and the printer works do not after windows update

  Windows xp, mcafee internet security

  Recently, I ran a windows update and leave my computer turned off.  When you turn it on, the were (are) of the internet and the printer does not.  I went into Device Manager via Control Panel to see if I could turn them on and there is nothing pulling up in the Device Manager.  All documents and are accessible, but I can't even start a new internet connection and cannot print.   I am currently using another computer (more modern) in another room.  I even tried the SafeMode (f8 in the middle) from the model and go to Device Manager and nothing was there.  I just tried to go through the f8 option and beginning to a previous state that worked and I have the same result...  Everything is saved on that on a 350g portable hard drive.  It would just be easier to wipe the hard drive and start over? If so how would I do this reformatting?  Thanks for any advice.

  Michael

  Hello MikeKloss,

  Before you destroy by formatting the hard drive on your computer, I suggest that you do a restore of the system on the computer by choosing a restore point when it was working fine. You can check the link that will give you information about how to restore the system on the computer below:

  http://support.Microsoft.com/kb/306084

• HP Photosmart, can not sweep, the printer works.

  ProductName: HP photosmart C.4289, Internet Exploder, Windows Vista.

  Printer works but no scans, reason: Solution Center: react; No hp devices found.

  Actions:

  Download driver, 96% progress to stop and return. Signal: Irreparable mistake by installation.

  Analyze: Plugin HP Installer recovery does not work.

  Signal of microsoft / windows: there is a problem, why programming is not working properly. Closed programs, as soon as the solution is following is the available information.

  Scan of doctor: print, scan problem reg. Solution: download again.

  Microsoft solution: download again.

  conclusion: no result.

  I hope you can help me. Thank you.

  This message was not a solution, it is a correction. In the first mail of the number of the printer was incorrect.

• The printer works, but does not print--just a blank page comes out.

  How can I make the printer actually print.  It was working a few minutes ago... then he started printing in green.  Is there a place to check the color?  I wanted to print something from black, and then it does not print at all.

  Hello

  What is the brand and model of the printer?

  Try the steps in the following methods and check the status of the issue.

  Method 1:

  Run the printer Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 2:

  Printer in Windows problems.

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• I have a problem with the printer works is not on Windows 8.

  Original title: device

  my printer has stop working.  Convenience store tells me that the coils do not work.  How can I solve them?

  I suggest you to uninstall the printer and install the latest printer driver for the printer model you are using.

  I see an error message about "spooler" problems

  A print spooler is software that temporarily stores the disk printing hard or in memory until the printer is ready to print.

  If you were expecting an abnormally long time to print a document, or if you see an error message about the print spooler, you may have to restart the spooler to print on your computer.

  To restart the spooler, the simplest method is to save your work and restart the computer. Alternatively, you can try the following steps:

  To restart the print spooler service

  1. You must be logged on as administrator to perform these steps.

  2. Press Windows key + R
     Type: services.msc
     Press enter on your keyboard

  3. Right click on the print spooler service, and then click Properties.

  4. On the general tab, next to startup type, make sure that automatic is selected.

  5. If the service is not already running, under Service status, click Start and then click OK.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

• How to start the printer works if it does not recognize theprinter hplaserjet1010

  I tried to connect my printer to my laptop but it does not meet the laserjet1010 of the printer

  If you have Windows 7, then your printer is not compatible with Windows 7. See:

  http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c02535920 .

  There are Vista drivers that might be interesting to try, but do not bet on it.

• Upgrade to windows 8, the printer works?

  Just a proactive advice to throw out there during the upgrade to Windows 8 drivers.

  To make a successful transition, you may want to uninstall the drivers for windows 7 because the printer first before you run the PIW (Printer Setup Wizard) and install drivers for the printer to Windows 8. Make uninstall through programs and features in Control Panel.  This will save a lot of hassle and time on the road.  Here is a link to the PIW as well.

  http://support.HP.com/us-en/document/c02691615

  I hope this helps!