During the stoppage of the partition, partition still on the hard drive Macbook

Similar Questions

• Question of replacement for the hard drive MacBook Pro Late 2008

  Hello

  My MBP HD headed to the exit so I'll take the plunge and get a replacement SSD to install it.  Being not too tech savvie I'm trying to cover all the bases before starting the replacement so I think I'm OK to get to the old and a new one outside.

  I read that a clean install of Mac OS X is recommended.  The plan is to install the new SSD and connect the old HD the MBP for a speaker for the migration of files once the SSD has been formatted and installed operating system.  One of my questions is what OS can / should I install in the first place on the new SSD.  I have the Leopard installation disc that came with the MBP, I also have a Snow Leopard install disc I bought (this is the version 10.6.3).  Start with the Snow Leopard disc or do I have to install Leopard first?  I would get the new OS SSD up to version I'm currently on (10.7.5).

  My other question is around RAM.  As part of the upgrade, I plan to replace and max of RAM, I've seen is now 8 GB between the two slots.  I read what the maximum capacity to 8 as part of an update of the firmware.  So the question is: should I do all updates of OS before installing the RAM?  The MBP would difficult treat 8GB if the firmware update is not installed through the different software updates that will be needed once the OS is installed on the SSD?

  Advice/suggestions appreciated.

  See you soon

  J

  Replace the RAM can be done at any time. If you have already downloaded the firmware required, it has already updated your material and will not be lost when you replace the hard drive. However, according to Apple, your computer can manage only a 4 GB. I could be missing something...

  See here: MacBook Pro (15-inch, Late 2008) - technical data sheet

  As far as your OS issue, the best thing to do is get the updated software to match the information that you are migrating back (to make sure no problem with migration). The best way to do it, is to download recovery disk wizard and install it on an extra USB key. This allows you to install Lion without having to install Leopard or Snow Leopard first. This will also use disk utility to format the new SSD correctly.

  DOWNLOAD: OS X Recovery Disk Wizard v1.0

  How to: OS X: on Recovery Disk Wizard - Apple Support

• Did a system restore complete with built-in recovery partition on the hard drive, the recovery went well, but the computer is still slow and freezing.

  Original title: computer always slow and freezing after clean install

  It is a compaq 2007 desktop running windows vista premium, I work on it for a friend, they said he was running slow and freezing up all the time so I just went ahead and did a system restore complete with built-in recovery partition on the hard drive, the recovery went well but still have the same problems with the computer being slow and freezing up. any help would be appreciated thanks.

  Hello

  
  Step 1: I suggest you try the steps in the Sub articles to solve the problem of vista performance.
  http://Windows.Microsoft.com/en-us/Windows-Vista/optimize-Windows-Vista-for-better-performance
  http://Windows.Microsoft.com/en-us/Windows-Vista/get-computer-speed-and-performance-information
  http://Windows.Microsoft.com/en-us/Windows-Vista/get-maximum-performance-from-Windows-Vista-from-Windows-Vista-inside-out
  Step 2: You can also check if the problem persists in the clean boot state.
  
  Put your boot system helps determine if third-party applications or startup items are causing the problem.
   
  Try the steps in step 1 in the article to put your computer in clean boot mode.
  http://support.Microsoft.com/kb/929135

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• The healthy Active Primary Partition: still can not Open Drive

  I am trying to save files on hard disk for laptop using a cable converter with a USB to my desktop PC. It shows healthy in disk management, but I can not even open the player to access my files. I can't open even to run a top Virus scan. I think that the drive has a Virus and does not start by itself.
  When I click on the drive, he said: "you must format the disk in drive F: until you can use it." "Do you want to format?

  Is there something that you suggest?  I was hoping that I could just run a Virus Scan with the converter cable to connect to the desktop computer, clear the Virus, and then my cell phone would agree.

  Hello

  If it is detected in disk management, you probably need to initialize the disk before it gets detected under computer

  Initialize new disks

  http://TechNet.Microsoft.com/en-us/library/cc771486.aspx

  Once initialized, you may need to format the hard drive. Once formatted the disk will automatically appear in computer.

  For more information, see the following Microsoft articles:

  Formatting disks and drives: frequently asked questions

  Managing hard disks: recommended links

  Note: Make sure that you have backed up data before formatting.

• How to partition the hard drive

  Hi, anyone knows how to disable partition the hard drive? Getting sick of the transfer of information between C: and E: Paulette

  Go to control panel, administrative tools, computer management, disk management.

  Do right click on E a remove it. After that, you should be able to enlarge C with right click and choose the option of not. But you'll have to save files on E first, so as not to lose them.

  If this does not work for any reason, you will still be able to use 3rd programs like partition magic. I've used several times and I am very happy with it.

• Question on erasing the HARD drive and partitions

  Hi my name is Fanta and I want to sell my laptop to someone, but I want to avoid impersonation so.
  I'll use an erasure software that will wipe away my whole HARD drive until there is no data.
  This is why I would like to know if there is a recovery on my HARD drive partition ready, and if there is a partition to the HARD drive recovery.

  Wipe tool will wipe the partition on the HARD disk. If he wipe the partition will take the recovery partition and if I need the recovery partition and I don't what will happen?

  Hello

  Generally, you won't find any recovery on the HARD drive partition. The Toshiba Recovery CD should always be supplied with the device. It must be only installed the operating system with the Toshiba drivers and utilities.
  However, if the Erase tool will also clear your partition then all files and data will be deleted.

  The HARD drive will be formatted again during the installation of the OS. If you want to use partitions on the HARD disk, you can create it in addition with Magic8 Partitions. I use this app and it of very great.

• Help a fool please ~ deleted partition, lost the hard drive size

  I'll try my best to make this as clear as possible, thank you for your time...

  Received my free copy of windows 7 home Premium

  Wanted a clean install (not an upgrade)

  Back up all the data and the programs that I installed

  During the installation of win 7, I deleted the recovery of the system partition and the 2nd partition of my HARD disk (has been labeled d, came that sort of lenovo factory, had 70 GB size I think)

  I thought that if I deleted the partition of the hard drive space would be added to the 1st partition and it did not

  Have materialized with the installation of win 7, and now I just have never found my C: and the GBs of the 2nd old partition so its as if I lowered my total HARD disk size

  How can I get my C: to have all of the 320 GB? Thanks for any advice!

  You can allocate the unused disk space as follows.

  Start > run > diskmgmt.msc

  Right-click on the Windows partition [should be C] and click on "expand". Extend partition as needed and enjoy.

• Can I use the HP Recovery partition after formatting and partitioning the rest of the hard drive?

  I recently had my HP Pavilion dv4 2145dx laptop (Windows 7 64-bit) go kerput.  The Geek Squad said that the motherboard is dead.  I bought a laptop and I use this one for now, and I use the former dv4 as external hard drive.

  I intend to continue to use the hard drive from the old dv4 as an external unresolved for now, but I wish we could fix the dv4 at some point in the future.  Here's the problem: to get the most out of the former dv4 as external drive, I want to repartition it so that there is an NTFS partition and one HFS partition +.  This way I could easily use it with my Mac and Windows machines.

  But if I do that, I'm not sure if the image of HP recovery would continue to operate.  If it does not, then if/when I get the old dv4 a new motherboard, I couldn't restore the operating system from the recovery partition.  It is a problem, because I have not create recovery disks (stupid, I know - I'm definitely making them for the new machine).

  So, I want to do these two things:

  (1) create my dv4 recovery disks.  Can I do this if the dv4 drive is mounted in an external enclosure?

  (2) format and partition the drive dv4 (the leaving intact recovery partition) and later to recover the system from the recovery partition.  The recovery partition would continue to operate in these conditions?

  Thanks for any help that anyone is obtained.

  Hello:

  What you do to the C:\drive will make the ineffective recovery partition.

  You will not be able to create a set of recovery discs unless the drive is usable in Notepad.

  Can you still read all 25 characters of your product key of W7 on the bottom of your laptop broken?

  If so, you can do this...

  If you can read the Microsoft windows 7 25-character product key, you can download simple Windows 7 ISO files to burn on a DVD for the version of windows that is installed on your PC, and which is listed on the Microsoft COA sticker on your PC case.

  Burn the ISO with the option to burn the ISO on your DVD burning program and burn it at the slowest possible speed that will allow your program. This will create a bootable DVD.

  Or use the installation of Windows 7 USB/DVD tool to compile the ISO file that you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB compilation method.

  http://www.microsoftstore.com/store/msstore/HTML/pbPage.Help_Win7_usbdvd_dwnTool

  Use 25 characters on the PC product key to activate the installation.

  The key will activate a 32 or 64 bit installation.

  Then go to the support of the PC and driver page to install the drivers you need.

  Link to downloads ISO of W7 is below.

  http://www.mydigitallife.info/official-Windows-7-SP1-ISO-from-Digital-River/

  Or, you can probably still order a set of recovery disc for your HP laptop.

  http://support.HP.com/us-en/document/bph07143

  Paul

• How can I remove the recovery partition from a corrupt HARD drive that I replaced in a laptop?

  I replaced a HDD corrupted in the laptop of a friend and you want to reuse. How can I delete the recovery partition? When I try to use my Windows 7 computer management tool, it will not access? I did a complete player wipe (twice) what the partition is still there and I can't remove it. It's 14 GB of space I want to retrieve and use the HARD drive in another system at a later date.

  Thank you

  Try the command line option:

  Start cmd.exe as an administrator, then inside the window cmd, type

  DiskPart

  then, type diskpart

  list disk

  take note of the correct disc ID to clear

  type

  Select disk x

  (where x is the ID of your disk to erase)

  type

  clean

  your HARD drive will be erased completely

  or you can try the magic of partition:

  http://www.partitionwizard.com/

  or if it does not work:

  http://www.hirensbootcd.org/download/

  Hiren's boot cd and gparted tool available.

  You must create a bootable CD or USB pen as media.

• What is the speed of the hard drive of the 2015 2 and 3 to merge disks partition?

  I was looking through the Apple site and was wondering about the speed of the drive in the iMac in car merger. On their site it says that the 1 TB Fusion drive has 24 GB of Flash memory, and 2 models to and 3 to have 128 GB of Flash storage. But it does not say what the speed of the hard drive partition, which is what I want to know. It is 5400 RPM, or even 10000 rpm or 7200 RPM? I don't know, but I want to know. If anyone here knows the answer to this question, I would appreciate a response. Thank you.

  I have seen it reported that the Fusion drives are all 7 200 RPM.

• Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  This has two questions:

  1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

  2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

  3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

  Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

  The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

  Then there is the BootCamp partition on the HARD drive partition #2.

  Is there a way to get what I need?

  That is what has been described in this notice of two canoes?

  Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

  n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

  Thank you.

  After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

  Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

  A. take backup

  1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

  B. fuse out of the merger in two physical disks drive: SSD + HDD

  1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

  Cs diskutil list

  2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

  I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

  Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

  and repeat for disk1/dev/disk1 which is the HARD drive in my case).

  This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

  2 create independent partitions (non-fusionend) for the installation of OSX.

  Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

  3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

  C. install on the HARD disk as drive didier autonomous not fusion.

  1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

  D. use BootCamp Yosemite f5 to install windows.

  1. launch Yosemite bootcamp.

  2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

  3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

  4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

  -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

  -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

  5. open Boot Camp Assistant again and only select the third option, install Windows 7.

  It will show you the screen to select what installation disk, select HARD drive.

  Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

  For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

  Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

  6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

  7. once the installation is complete, check that windows is functioning correctly.

  E. Si you want to upgrade to windows 10 Windows 7.

  1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

  2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

  F. reinstall OSX El Capitan

  Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

  1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

  6 type the 'diskutil list' command to list all disks and partitions.

  The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

  The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

  G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

  1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

  Cs diskutil list

  6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS GB SSD 121.0 disk0s2

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS 1.7 Untitled TB disk1s2

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 503.0 GB disk1s4

  5: Apple_HFS 801,4 Untitled GB disk1s5

  8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

  diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

  Note: Mark the group id of logical volume shown in the results.

  In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

  So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

  9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

  diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

  10 command "diskutil cs type list" to check the resulting fusion drive created.

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

  =========================================================

  Name: LVG

  Status: online

  Dimensions: 1815635525632 B (1.8 to)

  Free space: 90112 B (90.1 KB)

  |

  +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk1s2

  |   Status: online

  |   Dimensions: 1694646673408 B (1.7 to)

  |

  +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  ---------------------------------------------------

  Disc: disk2

  Status: online

  Size (Total): 1809780178944 B (1.8 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

  12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

  13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

  14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

  15. yet once please take personal responsibility on damage if you follow the instructions in this article.

• Tecra A8-104: how to create a second partition on the HARD drive

  Hello.

  I had to use the recovery disk, and I deleted by mistake my (two) initials of the partitions on the HARD drive. : ((now, I have only one.

  Can someone tell me how I can fix this?
  I want 2 partitions, not one. x 10

  The Toshiba Recovery CD could create two partitions.
  The installer will ask where or how install the OS on the HARD drive.

  For example, the HARD disk supports 100GB. So you can choose the first 60 GB for installing the OS and the difference (40 GB) could be activated after the installation of the OS.

  This can be done in the management of the computer-> disk management.

• How much better the partition of the HARD drive for dual boot: Windows 8 and Linux

  Hello

  I am a newbie in Windows 8, linux, Partition...

  I want to use my new laptop with windows 8 pre-installed on the following:

  Create a Dual Boot Windows 8 / Ubuntu
  Create on my drive C (single disk on my laptop):

  * a partition for the system
  * one for Windows 8
  * one for data and
  least for Ubuntu OS

  My goal is:

  -to install VmWare on Windows 8 and run Splat Checkpoint with virtual machines to make the FCTC laboratories.

  to install GNS3 on Ubuntu for CCNP Labs but with GNS3 to access the files in the data partition

  I have a Toshiba Satellite with 750 GB and 8 GB of RAM.

  According to you, what is the best size for my scores?
  Is there a better way to partition my C drive on my goal?

  Best regards

  I don't know if this is the right section, sorry for that. Feel free to move this thread in the appropriate section *.

  I think the size of partitions depends of the you want to use and install other software.
  So if you have a lot of software which runs under the Windows System I recommend to choose a larger size to win 8 partition.

  However, given that you have a 750 GB HARD drive, you could take 200GB for Win 8, 100 GB to Linux and the rest of the HARD drive size, that you can use for data.

  By the way: I found Nice YouTube video how to create a dual boot using 8 Win and Linux http://www.youtube.com/watch?v=E_Yd2jK-7Jg

  Welcome them

• Where could I find, live disc or other to restore the HARD drive recovery partition?

  Hello I have an A300 system 9 1M unit.

  I need to restore the HARD drive recovery partition, I had to change the hard disk drive, because he's dead.

  Is there a link where I could download the files? IMG to ISO or any other program that can create a new partition for recovery on a new drive?

  This computer is not under warranty, because it has more than 4 years.

  Thank you for all the support you could give me

  SEB

  PS: second question: which little hard drive disk could I buy for this model? Wich, 2 1/2 hdd and sata connector? IDE? I do not know.

  Post edited by: Seaone

  Hello, I have another question, how do I recognize the type of connector of the drive in this laptop?

  It's a sata II or sata 3.0 compatible?

• Satellite A100-192: what I lose warranty if I create a partition on the HARD drive

  Hello everyone,

  I want to format my laptop (Toshiba Satellite A100-192) and 2 partitions. I've been using EMP cd + recovery CD, it's very simple, but I don't want to install all the programs of Toshiba. I want to install a Windows 'fresh '.

  I read all the messages on Toshiba Express media CD + recovery CD and xxxx on the HARD drive. I'm a bit confused. Many of you said: 'use only EMP recovery cd + CD' or ' do not xxxx 2 or more on your HARD drive - you can lose the warranty of your laptop.

  I have another CD with Windows XP Pro OEM. It is best to create partitions, install from that cd and after that to install the drivers from TOOLSCD?

  Of course, I don't want to lose my warranty, please tell me how it is better to do!

  Sincerely yours.
  Daniel

  Hello

  > Many of you said: 'use only EMP CD + recovery CD' or '' do not 2 or more partitions on your HARD drive.
  ' > you can lose the warranty of your laptop.

  Someone told you a big story :)

  It turns out; you do not lose the warranty after you create partitions on your HARD drive!
  Only if you open the laptop and will try to fix something by yourself, you will lose your warranty.

  Of course, you can use your fresh and original Windows operating system. After the installation of the operating system, you can install the drivers from the CD tools Toshiba or you're going to download it from the page of Toshiba.