e1000 and Debian 3.1 module on a Tecra M5 L2 r2

Similar Questions

• How to compile and install the kernel modules after nation and nipalk for installation of Gentoo 64 bit?

  We are trying to install a PCIe 6251 DAQ card in a box of Gentoo 64 bit running Linux kernel 2.6.28 - gentoo-r5 4.3.2 - gcc and glibc - 2.8.  We have installed RPM utilities to manage the installation.  The current problem is that we are not able to compile and install the kernel modules: nidmxfk, nimsdrk, nimstsk and nipxirmk.  Here's a summary of what we have done so far, and to what extent we got.

  First of all, we have changed the configuration of the kernel that we could export the init_mm unused symbol by changing the configuration option of the CONFIG_UNUSED_SYMBOLS = o kernel and recompile the kernel.  Then we installed LabView 8.6.1.  Then we ran the nation 1.9 installer who has installed the source code in vain on the compilation.  To resolve this problem, we have changed the function of pte_offset to pte_offset_kernel by editing the file/usr/local/natinst/nation/configures following the instructions here:

  http://decibel.NI.com/content/docs/doc-4511

  We were then able to compile and install the kernel nation module thanks to:

  . / configure
  do
  make install

  lsmod said that nation has been properly installed.  Then we ran the installer for DAQmx 8.0.1 by:

  . / INSTALL - nodeps

  To do this, we have received errors indicating that LabView support could not be installed because check addictive (incorrectly we think) stated that labviewbase86 has not been installed; This caused the installer to have an abortion.  Therefore, we refused to install support for LabView 8.6 and revived the installation program which produces the output:

  Installation of the driver NOR-DAQmx Distribution of Linux Installer version 8.0.1f0...

  Already to jump Edward - 1.9.0 - f0.noarch.rpm installation, same or newer
  installed.

  Pre Installation...

  Preparing... ########################################### [100%]
  1:nitimingi ########################################### [ 4%]
  2:nipalki ########################################### [ 7%]
  3:nipali ########################################### [ 11%]
  RC0.d directory not found, startup script is not accredited with init levels.
  4:labview80 - rte # [14%]
  5:ni653x ########################################### [ 18%]
  6:nicdigi ########################################### [ 21%]
  7:nidaqmxcapiexmp # [25%]
  8:nidaqmxcapihelp # [29%]
  9:nidaqmxcapii # [32%]
  LN: create the symbolic link ' / usr/local/include/NIDAQmx.h': no such file or directory
  10:nidaqmxcfgi # [36%]
  11:nidaqmxef # [39%]
  12:nidaqmxhelp # [43%]
  13:nidaqmxinfi # [46%]
  14:nidaqmxswitch # [50%]
  15:nidimi ########################################### [ 54%]
  16:nidsai ########################################### [ 57%]
  17:nimdbgi ########################################### [ 61%]
  18:nimioi ########################################### [ 64%]
  19:nimru2i ########################################### [ 68%]
  20:nimxdfi ########################################### [ 71%]
  21:nimxpi ########################################### [ 75%]
  22:nimxs ########################################### [ 79%]
  RC0.d directory not found, startup script is not accredited with init levels.
  23:niorbi ########################################### [ 82%]
  24:nipxirmi ########################################### [ 86%]
  25:nirpci ########################################### [ 89%]
  26:niscarabmm # [93%]
  27:niscxi ########################################### [ 96%]
  28:nistci ########################################### [100%]

  After Installation...

  At this point, after reading this report, we used the Gentoo rc update utility to add several scripts for the boot runlevel initialisation:

  update of RC - a boot nipple
  update of RC - a bunch of nipxirmu
  update of RC - a bunch of mxssvr
  update of RC - a bunch of nisvcloc
  update of RC - a bunch of nidevldu

  When the computer reboots, you get an error message indicating that the following kernel modules are not: nidmxfk, nimsdrk, nimstsk and nipxirmk.  lsmod shows that the nation and nipalk are installed, but no other kernel modules NOR are present.  modprobe-l shows that only nation and nipalk are available.

  So we have several questions:

  1. we install drivers in the correct order?  Should use us NI-VISA 4.5 or NOR-488. 2 rather than DAQmx 8.0.1?

  2. What kernel modules should be loaded for this equipment run?  How to compile and install the ones that we have yet, specifically nidmxfk, nimsdrk, nimstsk and nipxirmk?  Are there others?

  3. How can we get the installer to properly recognize that we have installed LabView Core and install support for LabView?  Are there additional kernel modules related to the support of LabView?

  4. What is the symbolic link that was not created in the DAQmx installation report? (ln: create the symbolic link ' / usr/local/include/NIDAQmx.h': no such file or directory)?

  I apologize for so many questions, but these seem to be the last obstacles to obtaining OR runs correctly on this system.  Is there other information that we can provide that would be useful?  Thanks for any help or suggestions you can offer.

  Craig

  Hey Craig,.

  Given that you use 64-bit Linux all kernel modules must be compiled for 64 - bit.  User mode binaries can be 32-bit, assuming that you have installed the 32-bit support libraries.

  NOR-DAQmx is a complex architecture and requires several kernel modules to support your PCIe card.  Most of these kernel modules have not been brought to support 64-bit Linux.  Some kernel modules are components infrustructure that are shared with other pilots OR as NI-VISA and NOR-488. 2 and have been brought to support 64-bit Linux.  Unfortunately, you need all the modules to use your hardware.

  I hope that answers your question.

  Shawn Bohrer

  National Instruments

• Question about the common modules on my Tecra 8200

  I tried to install common modules on my tecra 8200 with windows xp family. When I restarted the pc, I had a checksum error. Time and date when changed. I got a lot of error messages. What can ido to fix this.

  Hello

  Checksum error is caused by the RTC battery and if a BIOS checksum error message persists, this may indicate that the RTC (CMOS) battery must be replaced. The CMOS battery can be replaced by the authorized service partner.

  It's certainly not caused by common modules. Other error messages have noticed?

• Tecra M5 and Debian - need some suggest before you start

  I just bought a new Tecra M5.
  I need to use Debian on it.
  Use some suggest to give me before I start?
  Could I have some problems with comatibility?
  Thank you!

  Perhaps you will be not possible to run tools and look for some drivers.
  Create a backup of your important files before installing Linux. Create a second partition for Linux, then install Linux on that partition. In this case the Linux wouldn t have a bad influence on the first partition and windows OS.
  If something goes wrong, you can always delete the second partition Linux.

• Re: HARD drive need internal and business BT internal module for Satellite P300-156

  where can I buy HDD case internal and internal module for Satellite P300-156 BT?

  Try an authorized Service Center. There is a list on the Toshiba under Support site

• T440s / S440 / other 14-inch laptop and debian

  Hello

  I would buy a computer thinkpad notebook. However, I don't want to have problems when I install debian (drivers).
  Firstly, I am from France and I beg you to excuse me if I speak very well English but is an international language and I prefer to write my request in this language. Second, I'm looking a laptop that is not too heavy (I often need to go with it). So I think I'll buy a 14 inch screen. However, I don't know what model to buy. It would be nice of you if you could give me your opinion: what are thinkpad 14 inch (I5 or I7 processor) on which the installation of Debian will not be a problem?

  Thanks in advance for your help and wish you a good day/evening depending on where you live.

  Kind regards

  Vinou33

  Finally, I bought a t440s.

• FPGA and digital i/o Modules

  Hi all

  We have NI 9421 digital input and digital output NI 9472 Modules. We can run these modules into a VI under the 9073 cRIO chassis. While we have added the FPGA target under the same chassis, we cannot use the modules. We also install the scan engine.

  How can we use FPGAS and i/o Modules at the same time?

  Once you add a target FPGA in CompactRIO chassis, when you deploy the code, the cRIO is configured for the FPGA mode, which requires a bitfile compiled to connect with the C Series modules.  Remove the target FPGA or changing the mode of chassis in the project and by redeploying must reconfigure the cRIO for scan Mode, which allows you to use the IO module directly from the RT VI.

  For more information, see this post.

• synchronize the inputs and outputs of the module C digital 9403

  I want to program EEprom with 9403 module, but I got an error:

  Possible reasons:

  Specified route can not be satisfied, because it requires resources that are currently in use by another route.

  Source device: cDAQ2
  Point source: di/SampleClock
  Target unit: cDAQ2
  Destination terminal: Slot1/ConvertPulse

  Resources in use by
  Task name: _unnamedTask
  Source device: cDAQ2
  Terminal: / SampleClock
  Target unit: cDAQ2
  Destination terminal: Slot1/ConvertPulse

  Task name: _unnamedTask

  code:

  

  Okay, there are two levels of problems:

  the 9403 cannot use a timed with an easy task, and it cannot link di trigger with trigger, uff do!

  I solved with this: (the trigger is AI/StartTrigger)

  

• LabVIEW FPGA and real-time communication module

  Hi all

  I created a small program in labview FPGA which gets continually distance from the HC - SR04 ultrasonic sensor. The rest of the robot program is written in the time module real Labview. Is it possible that the distance calculated by FPGA module to read in time real module.

  I used the FPGA just because there micro-deuxieme counter, which helps me get the distance from the ultrasonic sensor.

  Thanks in advance.

  There are many ways this can be done, according to your needs.

  See the help article transfer of data between the FPGA and host (Module FPGA) for a breakdown of each method.

• E1000 and Road Runner

  I just bought a router E1000, but I'm unable to set up.  I have Road Runner but the router will not recognize the internet connection.  He has set up the wireless network fine, but no internet connection.  I know that I probably just change some settings, but I tried a few that have been previously published and have had no luck.

  Restart the cable modem.

  Cable modem will only provide a single IP address to your home.  If you had previously simply your computer or another connected router, the modem cable will always give only an IP address to this material until you unplug the power, wait 5 minutes and plug it back so that she forgets the previous device and assigns an IP address to your new E1000.

• CodeModuleManager and loading / execution of modules...

  I know that the CodeModuleManager can be used to create modules on the fly, but can be used to load an existing module and run it if it has no main method? I wanted to write an application that would have downloadable plugins that could be law enforcement main and executed.

  I am able to find my module and load it using the CodeModuleManager, but how do I make a UiApplication which does not show an icon? Parameter as a module of the system is the only way I have extension / inheriting application instead of UiApplication, but when I try to push a screen using UiApplication it gives me a ClassCastException. Is it possible to get a UiApplication of an Application, or I have to put my application as a module of the system?

• ASA5510 and AIP-SSM-10 module in promiscuous mode

  Hello

  I have a 5510 ASA with the AIP-SSM-10 and want to use just like an ID in promicuous mode.

  ASA 5510: ASA version 7.0 (8)

  AIP-SSM-10: IPS version 5,0000 E2

  At this point, we would like to configure a single interface of ASA to send traffic to the agreement in principle for the inspection of IDS (and continue to use our firewalls third existing). Is this possible?

  The following discussion gives to think this isn't:

  https://supportforums.Cisco.com/message/957351

  22.1.100.2/28 I have it configured on the interface Eth0/0 (outside) and 10.5.100.3/24 on the AIP - SSM management interface and switchports (Cisco 6509) have been configured by SPAN.

  Thanks for your advice in advance.

  Kind regards

  Lay

  You are right. Unfortunately, module AIP on ASA firewall does not listen on traffic SPAN. If you want that SPAN ports, then you can use the IPS (IPS 4200 series appliance) appliance that supports the SPAN traffic to inspect.

  PIX is also a firewall, not a feature of IPS, which cannot be used as an IPS device.

• Parallel development for cloud and On-Premise support/modules

  I'm new to the cloud of the OPA and we have currently a V11 OPA modules deployed on the OPA Cloud Services. The team tries to use the same modules in On-Premise OPA (10.4.5).  I understand that we are unable to open the project V11 in V10.4 OPM. Is there a way could continue to support and even development of the modules in these 2 platforms? Can we use modules to have a "code share"?

  Please advise on the appropriate strategy and challenges we have the prescription above.

  Thank you

  Jerome

  (A) the Oracle policy even modeling will serve as a development tool for the clouds and deployments on site.  The Hub OPA currently configured under the OPA Cloud Service will be available at the facility on site.

  The new version should be available in early 2015.

• Lightroom 6 PC does not recognize the serial number and has disabled the module development

  I bought Lightroom 6 at Amazon and initially installed without problem. Recently, he started saying that my trial is about to expire. I had uninstalled the trial before installing the original. Now it's saying my trial has expired and has disabled the develop module.

  I tried to get my serial number, but it has no effect and does not give error messages.

  I tried to uninstall. I tried to re - download the app on Amazon. Nothing works. I get just this screen:

  

  It is not necessary to uninstall the trial version before installing the "full" version, because there is no difference in the programs. It is virtually the same program. Enter a valid serial just cancel the limitations of the trial. Your installation seems to act as creative cloud installation. My recommendation would be for you to uninstall completely, including the creative application manager if it is still installed. Download the latest update from the following Web site, and then install it. Use this serial number to see if it will activate.

  Update of Lightroom

• Before and after the problem - Module Development - Windows 7, 64-bit - Lightroom CC v. 2015.5 - camera raw 9.5

  I use Windows 7 64-bit, Lightroom CC 2015.5 Camera Raw 9.5 and the module development on a feature photo ' before and after ' does not work.

  He shows me the image changed, but not the original (I don't know exactly what another image "edited", it shows me).

  In the screen shot, you can see the pictures "before and after" and the one original overxposed.

  I hope I am clear enough.

  Any suggestion?

  

  Thank you :-)

  Click with the RIGHT button ON the import step in HISTORY (do click NOT just what this will change your photo AFTER) and select "copy history step settings to before.

  "