E3000 and wired printer?

Similar Questions

• OfficeJet Pro 8620: Can I use the Wi - Fi access and wired on HP OfficeJet Pro 8620

  I have Linux and Mac computers on my network.  I have no difficulty in printing (usually), rarely, I can print from my Mac computer via a wireless connection.  I also have trouble sometimes maintaining an internet connection on my Mac: sometimes falls my wireless connection.

  MU question is: regardless of the operating system, is it possible to have both wired and wired connections to the printer at the same time?

  Thank you.

  # You can have USB and wired, or USB and wireless.  You can not have wired and wireless at the same time.   As soon as the Ethernet cable is connected wireless is disconnected automatically.

• try adding a wired printer Brother MFC-255CW on a Windows Vista-based computer

  try adding a wired printer Brother MFC-255CW on a Windows Vista-based computer

  Hi jande1,

  Please see the following link for the Brother's Web site:

  http://welcome.solutions.brother.com/BSC/public/us/us/en/DLF/DLF/000000/003800/dlf003837.html?reg=us&dlid=dlf003837&dispforlist=1&OS=74&type2=1&prod=mfc255cw_all&c=us&lang=en&flang=40

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• cannot print wireless to wireless using a but access point wired printing (pc) wireless technology is very well

  I have a HP OfficeJet 8600plus N911a CM749A # product who has problems in this impossible to print wireless to wireless using an access point but Wired print (pc) wireless technology is fine. We have 4 pcs in a network cable that work very well try to print to the printer which is connected wireless. They installed the software and discovered the printer very well. When you try to install the printer on a Win8 Tablet and a laptop Win7 that neither would discover the printer, so I have two devices connected by ethernet cable and ran the facilities in the same way as the PC and installed everything and worked fine. But, after I disconnected the wire and reconnected or the other device wireless again (they go OK so I know that they get an address) when I go to print to the 8600 it says there is no communication to the printer. BTW, I can install (and installed) other (cable) HP printers on the network as the computer laptop and Tablet AUTODECOUVERTS and print... Yes, ideas on why it loses its Wireless communication to the wireless printer. He turns a few odd Protocol or discovered that did not pass on a wireless system?

  Thank you for answering my question and I wanted to know was the brand of the router.  I suggest making sure the router firmware is up to date as well.

  Here is a link to a post I did on the various ports used by HP printers for reference.

  -Incoming and outgoing Ports-

  So all your work computers don't encounter this issue?  Once again, while in the router, verify that wireless isolation is not activated.  A question also, I do not see has anti-anti-virus/firewall you had on your main computer that you are using?  Maybe it's not the cause, but that depends on the software, too.

  -Security and Firewall.

  You have all the exclamation points in your device manager?

  Let me know what is happening when you try another access point.

• I need this laptop wireless connection to my office wired printer. How

  I want to this laptop wireless connection to my office wired printer. How can I do that. I tried to do the thing of the shared printer, but my office is old and uses windows xp, and of course, this laptop uses windows 7. My printer is an epson stylus photo r320. I want to have my wife's cell phone to also be able to access the printer. I connect to the internet via a cable comcast and have a linksys N Router e2500. I want to do this as cheaply and simply as possible. Thank you

  Hello:

  First you must enable sharing of files and printers in Windows XP. During this process, you need to change the name of your to WORKGROUP MSHOME workgroup to match the workgroup name in Windows 7.

  You should also turn on file sharing and printers in Windows 7, and turn off password protected sharing.

  When you have done all that, click View workgroup computers on the XP PC. You should see the two PC listed.

  With the laptop to Windows 7, you should see the printer connected to your computer listed with the desktop computer (you may need to click on see the whole map when you open the network and sharing Center). Click on the printer and click on connect. I hope that the printer is capable of Windows 7. If it isn't, it will give you an error that it cannot find an appropriate driver or another error.

  Paul

• WIRELESS and wired LAN do not know each other

  My internet provider installed a new cable modem, without capacity WIFI because I have an airport extreme base WIFI (with cable Express extensions).  Speed and quality are OK, wireless and wired, but there seems to be a wall of China between WIFI and wired (LAN): devices that are connected via a cable to my LAN are not visible from the wireless network and vice versa.  Airport extreme is not 'Bridge' mode ("because not of wireless on the new modem capability".)

  No idea of the reasons for this?  Thank you very much

  Sounds like the configuration of the device. With the airport devices it can operate as a device on the network or another firewall as its own network. I think that it is way jumpered to activate, this will allow you to configure the wireless on the airport, but your current router will do the DNS/DHCP and will be a single network.

  Now that you have configured as two routers on an independent network as there is no bridge.

• How to use the capture and the print button

  I tried to figure out how to use the capture and the "print" button, or add or what you call. I press it and the whole page of a different color changes, so I try to cut the section I want but I don't know how to send it to the printer. Can someone help me with this. I'm not at savvy with tech stuff, but when I find a recipe or something and it doesn't have an option to print a certain area, I can't understand how to use it?

  Thank you

  Andi Starbuck

  That happens to me is, I click and drag to make a rectangle of yellow selection, and as soon as I raise my finger on the mouse button, the part I've selected is captured as an image, a new tab opens and preview before printing, the image display. I can use the installation of the Page or simply print. But if I close the preview, this temporary image vanishes and I'm back on the page where I started. You see something different?

• When I try to print anything in Firefox, email or the Internet, I get a message that says: error in the printer and nothing prints. Tried the stuff even printing from the Internet

  When I try to print anything in Firefox, email or the Internet, I get a message that says: error in the printer and nothing prints. Tried to print things even to Internet Explorer, it works fine.

  Hello bdoolen, please try to reset firefox and see if that can solve the problem...

• Office 2011 and compatibility printing El Capitan

  I'm like El Capitan, but late last night, I tried to print a Word document for the first time since Windows Office 2011 and had problems - spinning beachball and then the paper closed.  A notice of 'error' came.  I couldn't print on the trendy hp1400 or the Deskjet wireless.  My wife has been able to print a focus on my hp1400.  We have 2 printers - a 1400 hp and a series of J611 Deskjet 3050 wireless [OCDFAE]. (MacBook Pro early 2011) 16 GB 1333 MHZ DDR3 OS X El Capitan 10.11.5 version) I've seen other reports of the same problem but have not found the solution.

  More of the puzzle.  My wife also has a MacBook Pro with Office 2011 - Siena had the faulty motherboard which had to be replaced a year ago.  It has updated to El Capitan and can print on the wireless.

  Contact Ms., Office 2011 prints normally (in general), when its not its a MS problem

• I'm on a mac and my printer does not print

  I'm on a mac and it sends the document to my printer (Hp Photosmart 4680 all-in-one), but the printer does not print. My printer worked fine and now it will not print. I'm doing something wrong. This has happened once before and I am frustrated with and left for about 2 days, I had tried everything I could think of, unplug the unit for an hour or more, uninstalling and reinstalling, checked ink levels they were very good. Then all of a sudden, he started working again. I turned on my computer and the printer, and surprisingly it comes to start printing. Does anyone else have this problem? If so what do you have? Or someone has any suggestions of what I can hurt!

  Thank you

  Make sure that your OS X is healthy:
  
  1. download and install OS X Combo Update.
  2. download and install the printer driversHP from Apple.
  
  Finally, download the latest version of the software for your printer from the "Support & Driver" link at the top of this page (if you want).

  Do not connect your printer via a USB hub, connect directly to your Mac.

• Can my older extreme join network of my new extreme and provide printing as an Express services?

  Hello to you all, kind-Apple-help-people...

  So, I just got a refurbed Time Capsule/Extreme to replace my old, short ' squat extreme n.  I have the new network that all together up and happy, no worries.

  Back in the day, I used to have a fleet of 1 St gen expresses established providing the air in different rooms and connected to the printer in the office. They disappeared for a long time now, but it occurred to me that it would be nice if I could put my older extreme, now retired, to such use.  I want to put in the office and my printer on the USB port.  I really didn't need to "extend" the network or anything fancy.  With my old man expresses, I just put them up to 'join' the existing network.  This "join an existing network" doesn't seem to be an option available when I run today Airport utility.  Can I do this?

  Sorry, but no. You can't have an AirPort Extreme 'join a wireless network' for the purposes of sharing printers or hard disks. At best, you could connect by Ethernet to your Time Capsule to this effect.

• AirPort Extreme A1408 (5th generation) low flow on both WiFi and wired

  Hi all

  I have an extreme A1408 Airport (5th generation), which is connected to the internet via a cable UTP (wall plug, the internet provider has its routers in the basement of the apartment building). My plan is to 1000 / 200 MB (down / up - Romanian RCS & RDS, Fib), however, I'm getting averages of 90 / 80 MB speeds on speedtest.net. The best I've ever had was about 180 / 200 Mbps, but that happened once.

  The low speed produce on both WiFi and wired (I have an iMac, a MBP, a 6s iPhone and an iPad Mini that connect through WiFi, on the 5 GHz network and a Mac Mini that is connected to the router), with my wireless devices to full signal strength and connection to 450 Mbps. Since low speeds correspond to the cable wire / WiFi (I expected to the Mac mini to outdo the other, since its on gigabit ethernet), this is not a discussion on how to choose the best channel (I tried auto or manual installation, with it on different channels) or change its placement (this corresponds with the MBP even right next to the router) to get the best reception.

  I tested the connection directly paste the cable in the MBP (via the adapter ethernet of love at first sight) and got 850 / 200 Mbps, then my provider connection works as expected.

  I also changed all cables UTP CAT 5, in order to support gigabit speeds to.

  My AirPort Extreme is on firmware 7.6.4, set up as follows:

  • PPPoE: always on
  • IPv6: link-local
  • Wireless:
    • WPA2 Personal (faster)
    • No network comments
    • the radio 802 mode value. 11A / n - 802.11b/g/n (self)
    • country of Romania
    • tried auto and manual selection of channels 2.4 Ghz and 5 GHz (by analyzing other autour networks)
  • Router mode: DHCP and NAT (NAT Port Mapping Protocol active)

  All iDevices I use are updated to their latest version of the OS.

  Is there something that I am missing? Any ideas?

  Thanks in advance for your time!

  Most likely the problem you see is that Apple has not designed the more practical to work with fiber Internet airport base stations. Although, the 5th generation 802.11n AirPort Extreme can manage, at best, 400 - 500 Mbps of throughput (in bridged mode) via its WAN - LAN interface, you will see about half of this when it is enabled as a router (as yours is.) In addition, if your ISP has their router activated ahead of yours, you can also receive a "Double NAT" error as well.

• black and white printing on HP Officejet 6700

  I have an IMAC 10.8.1 operating system.  I can't get my 6700 HP to print only black and white.  Even when I choose black and white printing, it will not be printed like that.  I can't implement any new printing preferences.  Now, I'm unable to print anything and yellow ink.  Went and bought a new black ink and printer recognizes that black ink is full.

  I don't know just something I am doing wrong.  Can anyone help?

  
  The application that you are trying to print from, launch the print dialog box (file > print).

• DeskJet 2546 b: Wireless print job stays in queue and poster printer offline after the upgrade to Windows 10

  I write a fix I found for a pretty annoying problem involving 10 Windows and HP wireless printers.

  My Deskjet 2546-b printer was printing OK wireless to the point 8.1 of Windows until that I upgraded my computer to Windows 10. Immediately after I upgraded to Windows 10, I could not scan, so I reinstalled the printer software and has worked for a day or two and then the printer would print not unless I restarted the printer or the computer - sometimes 2 or 3 times. This went on for a few weeks, sometimes it would be nice, sometimes, usually after the computer restarts, he would simply go offline. Once, he went offline 3 times when I was printing about 20 postage labels, recently he went 1 week without any problems.

  Long story short, after a lot of troubleshooting and to help a friend to HP, I found the problem to be associated with the WSD/service Port in Windows 10. My printer still maintains a stable connection with my Netgear router (wireless to the printer light stays on blue) and I was able to scan from the HP software and I could ping the printer... but printing would be just stuck in the print queue (the spooler service) and the printer showed offline in the queue, hardware and windows devices , or when printing from a program like Windows.

  I learned that if I went in devices and printers, until I sent a print job, if the printer showed offline, I could save time by restarting the printer simply and he would come every time (less painful) online.

  

  But it's just a solution and not a solution.

  Nothing worked... not even print and scan doctor. The final fix that worked was to define an IP address manually for the printer, and then I put the print driver to use a standard TCP/IP port.

  Here is the step by step. Your printer must already be connected to your network (solid blue on printer).

  Step 1: Make sure your printer uses a manual IP address

  (1) to obtain the IP address of your printer:

  • If your printer has a control panel with a menu, it's easy... Just look in the settings menu without wire/report and write your printer IPv4 address.
  • If your printer is not a menu of fancy and repower the computer and printer HP Print and Scan Doctor network menu display use (wireless), or you can connect to your router from a web browser (usually 192.168.1.1) and look at attached IPs (like me). Some printers can also print a report of the network when you hold down some buttons everything back up and running, but you will need to search the web site of the Internet or HP to find the process for your printer model - the report displays the IP Address of the printer.

  (2) once you have the IP address of the printer number, type this information in a web browser... like 192.168.1.x (where x is the last number of your printer)

  Web page of the printer should find - otherwise, use another browser (you can use a tablet or iPad if you want). HP has several different forms of printing of web pages (embedded web servers) depending on your printer model, but they all have a large number of parameters.

  (3) since the network tab or section, look for a manual IP address configuration.

  

  (4) suggest an IP address or type in a new.  I've personally used suggest and then replaced by the last number 241. You want to use a high number, something in the order of 240 to 250 to reduce the risk of problems caused by your router assign this number to something else on your network. Note the 4 digits for the new IP address manual, you will use them later.

  5) click apply and close the web page of the printer.

  Step 2: Make the print driver using the manual IP address of the printer

  Open the devices and printers in Windows, right click on your printing device and select printer properties. Follow the prompts to get the WSD port and on a new local port...

  

  1) click on the ports tab.

  (2) add the Port.

  (3) click on after the first screen, and then click new port type.

  (4) enter the IP address of the printer.

  (5) next.

  (6) select the new port.

  7) click OK.

  You have now two pilots displayed in the printers and devices window, you can now print... but you might not be able to scan and the HP printing software may not work as he might want to lets you add a new printer when you open it... If Yes, proceed to step 3.

  Step 3: Remove print devices and install a new one.

  Need to do this to get the software back HP synchronized so you can scan.

  (1) right click 2 print devices listed in the window of your printer and remove them by clicking on remove device.

  (2) open the HP printer Assistant software (from the icon on the desktop or you can search Windows by using the name of your printer).

  (3) installation/add a new printer... go fast and a new device icon is added to the printers and devices window.

  4) return to the printers and devices window and open the properties of the printer again for your printer icon.

  5) go to the ports tab (yet) and you'll see a new selected WSD port, select Port Standard, you created earlier in step 2.

  (6) you have now two print devices in the window (again), but now everything should work.

  These two devices alone from here on out. Do not remove one and everything should work fine. At least it worked for me. I hope it works for you. I'm hoping a Windows update resolves this problem soon, I see many people who cannot print or scan wireless after they upgraded - not just the stuff of HP.

• black and white printing

  Hej
  I have the MacBook Pro and HP Photosmart Premium printer and I have a serious problem to find the settings for black and white printing (no colors). I think I've checked everything. I would really appreciaty advice to solve this problem.

  Hi @Zuska,

  Thank you for visiting the Forums from the HP Support! I see that you want to print in black ink only on your printer HP Photosmart Premium with your MacBook Pro. Please follow the steps listed below:

  Printing with the Black Print Cartridge-only option

  1. Click file and then click print.