E325 will not be put into hibernation, SYSTEM_DRV offline

Similar Questions

• Windows XP Professional, Media Center Edition 2005 SP3 will not automatically put into hibernation

  I have re-installed drivers quick resume technology drivers & Intel Graphics & Sound & all associated drivers. but not good.

  Computer will be manually Hibernate & come out of hibernation, but is not automatically updated in hibernation?

  I tried the recommendations of microsoft all the but not good?

  The Device Manager shows all devices OK?

  Performed a restore the registry of oem disc & now put into hibernation very well at the moment, I hope that it will last? only lasted for a few days? its now to return again. ?

  not a fan of the system restores, especially under xp, but if it did work at one point, what has changed on your system, since it worked?

  http://support.Microsoft.com/kb/306084

  This is for two versions below, then you should be good.  But again this could be a temporary solution to a problem.

  Microsoft Windows XP Professional

  Microsoft Windows XP Home Edition

• Computer will not be put into hibernation when I close the lid

  I have a problem with my laptop. It is a series of Toshiba C55. When I close the lid it will not be in hibernation, even if I set power options to do so. This happens not all the time, but it happens enough that it's boring. If I close the lid and it will not be in hibernation, which means that it is in danger of overheating if I put in my backpack. If I use the start menu, it just goes to the lock screen, that's what I suspect it is when I close the lid. Help on that would be great.

  Hello Michael,

  Please keep us updated on the status of the issue.

  I appreciate your time and your efforts.

  I suggest you to update BIOS and drivers from the chipset and check the issue.

  Please update the chipset drivers from this link:
  http://cdgenp01.CSD.Toshiba.com/content/support/downloads/tc50157200c.exe

  Update the BIOS from this link:
  http://cdgenp01.CSD.Toshiba.com/content/support/downloads/scf6v140.exe

  Note: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes of the

  the settings are at your own risk.

  I hope this helps.

  Thank you

• T500 will not be put into hibernation on Windows 7

  I have a problem with the Hibernate. I did a fresh install of Win7 x 64, had some difficulty finding drivers and so on, but I got everything.

  Sleep function works perfectly, but when I try to put the computer in hibernation, is the only thing that is happening, that the screen turns off, and when I move the mouse or touchpad that it turns on again, I put in my pass or fingerprint, and everything is as if nothing has happened.

  I tried with graphics integrated or discrete, lenovo Power Manager installed or uninstalled, hybrid sleep is turned off, wake on LAN is off...

  Tried to disable network cards, USB ports... nothing helps.

  Any ideas?

  
  

• Satellite L305-S5885 will not be put into hibernation or sleep

  Satellite L305-S5885 on Vista premium SP1. It was bought by circuit city, and installed all the drivers from Toshiba.
  If I try to hibernation or standby, the laptop just restarts. I use the "balanced" power mode

  Does anyone have an idea how to solve this problem?

  Hello!

  Have you tried updating the BIOS too?

  You can find it on the Toshiba site. Check it!
  http://www.CSD.Toshiba.com-online download

  Good bye

• My Satellite A100 would not be put into hibernation

  Hello

  My laptop would not be in hibernation when I activate in the windows toolbar.
  When I activate the hibernation it will normally, but when the monitor takes blue and says "prepare put into hibernation" the monitor or system do not shoutdown (turn off), why?

  Is that the same for the suspend mode.

  I did a survey on my laptop and see I mode hibernation is enabled in control panel > power Setings > Hibernation

  My laptop is a Satellite A100.

  Sorry for my English.

  Thanks a lott!

  Hey Buddy,

  Sometimes, these problems of hibernation / suspension are caused by some programs that can't be closed from vista. Or your toshiba powersaver works bad, maybe some settings have been
  badly configured through that-I-know-what program or something else.

  I suggest you first: when you try to hibernate/suspend, then try pressing CTRL-ALT-DEL to see what applications are STILL running. Try closing the applications in the order of
  see when the machine will be really placed in hibernation. If this doesn´t has helped you, then try reinstalling the powersave (first uninstall correctly your system) and give a few
  What feedback happening.

  Greetz

• Satellite U205 would not be put into hibernation

  When I select Hibernate in the shutdown options that the classic windows xp appears with "preparation for the hibernation" and the machine hangs.
  This also happens when I ask him to standby mode.

  The screen is blank but power remains on. I have to press the power button / stop for 5secs in both cases to kill the power to the machine.

  Recently installed new software or microsoft updates? 3rd party software can sometimes this kind of problems.

  I suggest you try the following:

  -Update your BIOS to the latest version and put everything in your default BIOS
  -update your entire system and reinstall the powersaver which must be downloaded from the toshiba driver download site
  -If this is not enough, reclaim your machine and update all

  If hibernation won´t work any try you´ve, then give please a few comments here and we will discuss more on this subject.

  Welcome them

• Will not be put into service, but going through post-test and shuts down again.

  I have a Dell 2400 Dimension that I am having trouble with. I just clean with a can of air that own security that is supposed to be a dust collection system free of moisture. I don't know what happened, but I unplugged the power supply before as I have even try to clean it up. I put back together and he started upward, but the only thing it will do is to start up and go through the post test and fill the bar at the dell logo screen and then power that is auto off, but that's all I can get it to do.

  I don't know even where to start start troubleshooting, but it does not work with Vista and it's 32-bit, but for this, it's all I know about it right now. especially sense I can't turn it on.

  Quantum K

  You will need to test the connection (hard disk, RAM, graphics, connectors, etc.) in your Machine to make sure they are all secure.

  Working in here can get accidentally flipped a connection or a card and it loosened.

  See you soon.

  Mick Murphy - Microsoft partner

• My scanner will not be put into service after reinstalling my printer

  I reinstalled my printer once a computer re - build now the scanner won't initialize. The doctor fix download HP cannot fix it. There, can anyone help?

  Hello bassman-ian,.

  Open Control Panel, and then uninstall the printer using Add/Remove programs. When you uninstalled it, you have to restart your computer. Download and install the following features complete software and the driver for your printer at the link below.

  http://h10025.www1.HP.com/ewfrf/WC/softwareDownloadIndex?softwareitem=MP-19447-3&cc=US&DLC=en&LC=en&os=228&Product=90764&sw_lang=

• laptop is not put into hibernation after "standby mode"

  Reference Dell dear community,

  I have an Insipron 17R core i5 zm2410, NVIDIA Geforce 525 m, win8 64bits and I am facing a problem with hibernation mode / sleep.

  About 2 weeks ago my laptop went mode hibernation after beeing in mode 'sleep' for 2 hours on battery (for total draining of the battery to advoid).

  Now, it is not do it anymore but remains on "sleep" during all the time and drains the battery.

  I usually remove the power cable from the laptop during the night because of the noise of the adapter and the laptop always put into hibernation after beeing in mode 'sleep'. I went over the configuration in options plans and power supply and even reset and configured them again, without success.

  The only changes made to the system are important updates of windows

  I'm grateful for any suggestions or solutions.

  Have you checked to see if Hibernation is still active? Open an administrator mode command prompt and type: powercfg/h on.

• computer won't stay asleep or put into hibernation

  I have recently reinstalled Windows 7 on a desktop computer.  I used to leave it on all the time but now I want it to go to sleep or put into hibernation after a few minutes (and stay that way until we want to use it).  I tried to sleep, hibernate and hybrid sleep.  It will turn off, but in a few minutes he returned upward by itself.  Sometimes it seems to scroll, and down every few minutes.

  I read that USB devices can cause this, but only the mouse and keyboard are attached via the USB port.  There are two internal hard drives.

  A thought-

  Check the network and sharing Center

  Some settings of the map change

  A click with the right button on your network adapter

  Select Properties

  Select Configure, then power management

  and make sure that allow this device to wake the computer is not checked?

• The Polygonal Lasso tool will not systematically put points on a selection.

  The Polygonal Lasso tool will not systematically put points on a selection. When I click on select and moving to another point at random don't graph a line from the last point to the new I want. I can go back and click again to the previous point and sometimes it will follow until the next point, but sometimes with simply close the selection prematurely.

  This happened after I upgraded to Windows 10 Version 1511 (OS Build 10586.318).

  Is there a solution to this problem?

  Adobe Photoshop Version: 2015.1.2 20160113.r.355 2016/01 / 13:23:59:59 CL 1059143 x 64

  Operating system: Windows 64-bit 10

  Version: 10 or higher

  System architecture: Intel CPU Family: 6, model: 15, Stepping: 2 with MMX, SSE whole, FP SSE, SSE2, SSE3, SSE4.1, SSE4.2, AVX, AVX2

  Physical processor count: 12

  Processor speed: 1896 MHz

  Built-in memory: 16308 MB

  Free memory: 12163 MB

  Memory available to Photoshop: 14515 MB

  Memory used by Photoshop: 70%

  I was finally able to contact the customer support of cat care and the agent, Arjun Hohli, was able to do repair. I tried to follow along what he was doing, but lost track. It seems to heal by resetting preferences, uninstalling and reinstalling CC files. It was a problem with PS CC 2015 and Windows 10. I suggest to anyone having a similar problem to jump the forums and go straight to the Contact Customer Service REPS the remote access feature works fine and save a ton of confusion. It allows to see the real problem rather than relying on the customer precisely describing the anomaly, the support staff.

• Probook450G3: question sleep/put into hibernation

  I did a fresh install of windows 10Prox64 on this laptop which is originally pre-loaded with windows7 Prox64. I installed the drivers on the disc included. now, every time the laptop into hibernation or sleep I can't wake him up - the screen blinks several times then turns white. Nothing comes on the screen even not the mouse pointer. I can only continue by making a forced power off feeding and when I start her works normally as long as he does not sleep. I installed all the updates driver/Windows with the same result. Is there something else I can try other than to return to HP?

  HI Lotto,

  Please download and install the software HP support assistant from this link:

  http://WWW8.HP.com/us/en/campaigns/hpsupportassistant/hpsupport.html?JumpID=va_r602_us/en/any/PSG/pl_ot_ob_ds_pd/hpsupportassistant_cc/DT & _sm_au_ = i7VQZMWMQRfwpVps

  It will help to identify and correct the missing drivers and updates also.

  This link also contains manuals on how to use HP Support Assistant. Make sure that you are connected to the internet during this operation.

  If this does not work, you can try to reset your power options "by default" in the microsoft windows system.

  and in the end, as a workaround, you can modifty power plan options to avoid hibbernation or standby mode.

• L26500 will not be put on after that media jam

  Hello, this problem had beed going on for months... and through 2 firmware updates. After turning off to clear a jam of media, the printer will not feed when you press the power button. However it randomly starts anywhere from 30 to 60 minutes later on its own... It's BAD for my business but also extremely frustrating. Does anyone else know this and if so you have found a solution?

  Thank you

  Serendipity has solved my problem because of stupidity...

  Every time I had a media jam I would pull the plug because I didn't wait for the printer to cool down before going off to remedy the situation. The outputs are located right next to the printer for easy access was the best way for me to power down. Now, I find that this sudden loss of power is what caused the delays with my printer restart. I guess that something in the circuit is not as it's abrupt loss of power and when I plug it back, he must go through some diagnostics to make sure that it's okay to start up, although there is no LED activity or heard sound... Yesterday, I had a media jam, but it was before the heated printer so I hit the power button and the machine will stop after a few seconds. Once the problem is corrected, I pressed the power button and voila, he began. I have since stopped and restarted a dozen times with the power button to verify a second time and also pulled the cord several times...

  Bottom line is don't PULL THE PLUG to POWER DOWN!

  After a media jam in a printer heated, I now press the power button and help cool radiators more quickly by stirring up the front of the printer. He definitelt speeds things upwards, and the printer starts right with the power button when I'm done fixing the jam.

  Yay.

• Computer will not start after the installation of Kaspersky, will not even go into safe mode

  I tried to install Kaspersky on my laptop this morning to roll some viruses on my computer. After you restart during the installation, I got the blue screen of death with a STOP 0x000000F4 error code. I can't use my phone at all now, and it will not work in SafeMode either. I tried to restore the computer to before that Kaspersky was installed but it cannot do so. I tried to restore to the last known good configuration, but that did not work. I have no idea what to do now. My laptop is basically useless now and I am very angry.

  If I have the Kaspersky disk in I kind of access Kaspersky, and it keeps telling me it is obsolete and must be updated, but it will not be updated. Also, it tries to mount the drives or something and gets stuck trying to create the swap file. I don't know if it's important, but I'll post it anyway.
  I'm at a loss to know what to do...

  If you have tried to install an AV program after your PC has been infected you left it too late.

  Your safest option is to use your recovery discs to get destructive if you plant (make sure that the external devices are disconnected during this process)

  I hope that you, the data has been saved you will lose everything on the PC

  Once recovered allow windows update to do its thing for Important updates ONLY. It may take several reboots.

  If any update fails cure this problem before doing anything else.

  Once the update finished visit of manufacturers of laptop for important driver updates to update necessary.

  Only after this has been done, you should start installing software or external devices.

  If an installation fails, solve this problem before