Ec0000013 error MESSAGE STARTING

Similar Questions

• HP Pavilion Notebook 15-p050ca: graphics driver error message started after the upgrade of Windows 10 model installed on #: G6U13UA #ABL

  I have recently upgraded to Windows 10 and since then, I received the following message through a game: "display Intel HD Graphics driver Driver for Windows 8 (R) stopped responding and has successfully recovered."

  I checked my graphics driver and it says that it is up-to-date.  I tried installing the latest drivers for my laptop model (according to the HP drivers page), December 15, 2015, installed without a problem, but no version has not fixed the problem.  An error message appears when I try to install the March and April, 2016 versions of graphics drivers, claiming that they are not compatible with my computer.

  I also tried the Intel and HP driver update utility and told me that my drivers are up to date.  However, when I look at the properties of my Intel(r) HD Graphics Family in Device Manager, I noticed that information on the events tab says: "peripheral PCI VEN_8086 & DEV_0A16 & SUBSYS_227E103C & REV_0B\3 & 11583659 & 1 & 10 still requires the installation."

  I don't know what needs update on my computer or if this driver is incompatible with Windows 10 and there is not yet an upgrade?  Advice or opinions would be appreciated!

  My computer model is the 15-p050ca HP Pavilion Notebook PC (ENERGY STAR) model #: G6U13UA #ABL and the graphics driver is version #: 10.18.15.4279

  I went back to 8.1 for Windows and ran the store several times and then reinstalled Windows 10.

  I watched the graphic version installed and version 20.19.15.4331 dated dated 18 November 2015, but he still claimed there was an update of the graphics driver.  I tried the update and it was version 10.18.15.4279 dated August 2015, which was the same version that was installed when I had problems (and the same version on the HP website), then I went back to the 20.19.15.4331 version.

  I tried all the graphics drivers listed for my computer on the HP support page and again, I had the same problems with them as I had before (either claim that my computer has no minimum requirements or my graphics driver crashing).

  With the current version (20.19.15.4331), my graphics driver has stopped at least for now crashing, but I assume that this is not a specific driver HP and is only based Intel?  If so, I recommend HP glance on the issue, I've had if they claim that these drivers are supposed to work for my computer when my computer is, in fact, not accept them.

• Error message starting Windows "username and password do not match."

  The message is, "Usernam and password do not match."  I want to delete this message permanently. How can I do?

  * original title - I keep getting a Message on StatrUp.*

  Hello

  1. are you able to connect?

  I suggest to start the computer in safe mode and check if the same problem occurs:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  If not, then my brother this link and check if this may help:

  http://support.Microsoft.com/kb/189126

  It will be useful.

• This just error message started appearing yesterday: Application JavaScript - TypeError: window CloseAlert not a function.

  Application of JavaScript - TypeError: window of the CloseAlert not a function.

  What causes this error, can you help me fix?

  I use Windows 7 and the latest browser Foxfire.

  • If you have many extensions then first turn on half of test extensions that half the problem.
  • Continue to divide the bad half that still has the question until you find that one is causing it.

• Loading (bnfgxamam.dll) just a RUNDLL error message started appearing at startup

  I searched (including subfolders and hidden files and it does not find anything.) There is no mapping, the error msg displays (C:\documents and Settings Local Settings Application Data data\ypgnmcmst\solutionAV\bnfgxamam.dll owner).

  I ran a scan (avg) and it came with nothing. I'll run MalwareBytes then. Any thoughts? Thank you!

  It is probably malware. Let us know the results of the Malwarebytes scan and we can go from there. These errors appear generally, after the malicious software was detected and removed for the most part, but remains were left. The error basically means boot entry in your registry is looking for malicious software components, but is unable to locate them accordingly, as shown, the malware has, essentially, been removed.

• Since this morning my Thunderbird (v24.4.0) does not load any new messages. It gives me an error message saying that the RETR command has failed.

  My T-bird was working fine last night but this morning I get an error message starts "the RETR command has failed..." "whenever I try to retrieve new messages (he tells me there are 23 of them), I get this error message. I use the version above on a Windows XP machine running.

  No one here has the ability to do anything to your email address. Your email provider was just having a bad day and it is corrected now.

• Error message: not available with this Apple ID update

  App Store displays the available updates, but after choosing "Update", the error message starts "Update not available with this Apple ID" appears. All of the applications in question were purchased with the current Apple ID.

  Mac Pro (2008), 10.11.4

  Please test after each of the steps that you have not already tried it. Stop when the problem is resolved. Back up all data before making any changes. Remember, no one here is Apple or can help in problems of service the customer.

  Step 1

  If you have recently changed something in your Apple ID account (for example, the password), log out of the App Store and reconnect.

  Step 2

  A purchased app can only be updated by logging into the App Store with the same identifier Apple which was originally used to buy it. There is no way around this restriction, which applies also to the free applications. If you can not connect to help ID the buyer, remove the app and reinstall it. You will have to pay for it, once again, as appropriate.

  Step 3

  If you receive the alert when you try to update a grouped iLife application, select the shopping page in the App Store and find the application in your purchase history. If there is a button marked ACCEPT on the right, click on it.

  If you have a used Mac, bundled apps related to Apple ID of the original owner and may apply to you. Reportedly, customer service has published codes redemption to some owners of second who asked, but it is not guaranteed.

  Step 4

  If you try to update the iLife or iWork applications that were installed from a purchased DVD, or if you have a refurbished Mac purchased directly from Apple, contact App Store customer service for a redemption code. If necessary, you will be asked for the part number of the DVD.

  Step 5

  In the App Store menu bar, select

  Store ▹ view my account

  Enter your Apple ID to the command prompt. In the lower right corner of the window that opens, click the reset button. Close the window.

• Various recurring error messages blue box when the laptop is idle

  I have a new (10 months) HP Pavilion dv7 - 3165dx running windows 7 home premium 64-bit.  After that laptop sitting idle for a while, the screen goes black with a blue box error message.

  01/02/11-02/14/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Disable or uninstall any antivirus, commercial defragmentation or disk backup.  Check the configuration of the disk hard yoru and check the updated drivers.  Run CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Call Technical Support HP - a talked to Josh: I was sent to HP.com support site to download software downloads and the pilot.  Said it is known the problem and had me run the CHKDSK command to automatically solve problems.

  02/16/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Make sure you have enough disk space.  If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates.  Try changing video cards.

  Check with your hardware vendor for updates to the BIOS.  Disable the BIOS memory options such as implementing caching or shading.  If you need to use safe mode or remove or disable components, restart your computer, press F to select the advance boot option, and then select Safe mode.

  Technical information:

  Stop: OX0000007E (OXFFFFFF800032D3905, OXFFFFF88002B97288, OXFFFFFFFFC0000005, OXFFFFF88002B96AFO)

  Data collection for the crashdump...

  Call the HP Technical Support - talking to Matt: check space drive, and said that it was very good.  Updated graphics driver.  Disabled the hard drive protection.  Power options reset of Hibernate to standby mode.  Update BIOS of F.10 F.15.  Ran test drive: Smart check, DST short and long DST all spent.

  02/17/11

  Error message: A problem has been detected and windows has shut down to prevent damage to your computer.

  System_Service_Exception

  If this is the first time you've seen this stop error screen, restart your computer.  If this screen appears again follow these steps:

  Check to make sure any new hardware or software is installed correctly. If it is a new installation, ask your hardware manufacturer or software, the windows updates, you might need.

  If problems continue, disable or remove any newly installed hardware or software.  Disable the BIOS memory options such as implementing caching or shading.  If you need to use safe mode or remove or disable components, restart your computer, press F to select the advance boot option, and then select Safe mode.

  Technical information:

  Stop: OX0000003B (...)

  Data collection for the crashdump...

  I don't ' know what to do at this point.  HP phone support seems unable to solve my problem.  Can someone help me?

  Hi DP - K,.

  Thank you for all the helpful tips.  This weekend when I saw my McAFee scan/security reports, even if the McAfee Security Center shows that viruses and spyware works, he did not run a weekly full scan on my laptop since the end of January.  I don't know if he tried to scan and then breaks down, or it will not start.  When I tried to run a manual scan, windows shut down and I got a blue screen error message after about 5 hours of scanning - 63% digital.  When I ran the HP System Diagnostics report, it showed that my Security Center has not recorded an antivirus product.  "The Security Center cannot identify a current antivirus application.  There is no product protection antivirus installed or it is not recognized. "When I ran the HP reliability and history of problem report, it showed that my error messages started on 01/02/11, which is what I remembered.  I was able to restore my laptop to 23/01/11 when I had no problems and then, I uninstalled McAfee security and re-installed software.  I manually ran a full scan and it took 5 hours to complete, it has completed and reported no problems.  I look today and so far, no problem.  If the problem happens again, I will try the suggestion of Avast below.   Thanks again for all your great suggestions.

• 0x80016ba error message

  I have vista 32 bit with the Defender built in.  I don't know when the error message started because I immediately added suites mcafee, I am also a subscriber of 3 years.   0x80016ba continuelly error MESSAGE is displayed at the start of vista.  I was unable to click the Defender to open it.  I tried to locate the defender in programs and features, as I have been loaded on the page official windows defender, but there is no icon for it.  Then I went to windows Security Center on my pc.  All security features have green on the buttons.  I opened the malicious program button, mcafee was on but defender was off.  I turned on Defender.  It seemed that th problem has been solved, software Defender begins to open.
  But, after that I restarted the pc, what is the error message appeared and windows defender to stop opening.  I returned to the Security Center windows on my pc and clicked on the button of malware and defender was off.  I think that you will have to repeat this every time that you start the pc, if it is important for you, or until the issue is resolved.

  Hello 1stmorpheus,

  Thanks for posting on the Microsoft answers Community Forum.

  I've split your question where you have published to assure you that your question was seen and respond as quickly as possible.

  First, check to make sure that the Windows Defender service is started and the status is set to automatic. To do this:

  Click Start and type "services.msc", then the .
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation, then click on continue.
  Scroll down the list of services of Windows Defender and click, and then on the link to the left to start or restart the service if it is stopped.

  Right click on computer > manage > click Services in the left pane.

  Look for Windows Defender on the right and double-click it.

  The startup type should be automatic.

  Then use the following article to check that Windows defenders definitions are up-to-date.

  918355 KB - how do I troubleshoot Windows Defender definition update
  http://support.Microsoft.com/kb/918355

  Restart your computer and see if you still get the message error Windows Defender 80016ba.

  If please post again and let us know the results and if you still need help.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• BTTray.exe, error to start the Application.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:BTTray.exe, error to start the Application.

  • Programs that you have problems with the Bluetooth does not work overwhelming
  • BTTray.exe, Application error messages start error.
  • Recent changes made to your computer: just updated to windows update
  • What have you tried to solve the problem, I tried to look at Windows Update and also send mail to Microsoft

  Read the following article to see if it helps to solve the problem: http://support.dell.com/support/topics/global.aspx/support/dsn/en/document?c=us&dl=false&l=en&s=gen&docid=6CF68D431EAAB41BE040AE0AB6E16686&doclang=en.

  Are you still using the BTTray?  If this isn't the case, we can solve the problem in a more easy way.

  Go tohttp://technet.microsoft.com/en-us/sysinternals/bb963902.aspx and run Autoruns and click all.  Search bttray.exe or mfc80.dll and when you find it uncheck the box to prevent it from start to start.  Check the entire list as there may be several entries.  When you're done, click OK and restart.   The message should be gone.

  If this does not work, try a boot minimum http://support.microsoft.com/kb/929135.  If the problem goes away then it's just a matter of tracking down the culprit at the origin of the problem.   Follow the procedures described in the article.  Once found, remove, delete, disable or uninstall.  Once remember to put Vista in normal status, as described in the procedures. If the problem occurs in clean mode then just restore the system to normal and reboot - this solution will not work.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Error message at startup WDDM.

  Anything windows related on my computer will be internet Explorer, system recovery, windows live one care etc a WWMD error message started to appear at the start of my computer.

  Hi LewBhib,

  What is you get the exact error message?
  
  The display of Windows (WDDM) driver model is a new architecture supported in Windows Vista display driver. This display architecture is an overhaul of the Windows XP-based display architecture and gives users a better, more reliable desktop experience, while supporting graphics applications and new scenarios.

  Check if you have the latest updates for your graphics card.

  You can uninstall and reinstall the drivers from the Device Manager.

  1. open Device Manager by clicking the Start button and type device manager in the start search box.
  2. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. search the card display drivers, right-click on it and select Uninstall.

  4 restart the computer.

  5. Windows should automatically install the drivers.

  Access the link for more information about the Manager of devices below:
  Open the Device Manager:
  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager
  Kind regards
  Manasa P - Microsoft technical support.

• On Win 7 after update itunes Error Message error 7 (Windows error 127) whenever I have start download iTunes

  On Win 7 after update itunes Error Message error 7 (Windows error 127) whenever I have start download iTunes

  HI MikeGeorgen,

  I understand that you have updated iTunes on your Windows 7 computer, but now you see an error when you try to open it. I know it's important to have iTunes working properly, so you can sync your device, so I'm happy to help you.

  Make sure that you logged in as an administrator on your computer, and that you have the latest Windows updates. Then check out the additional troubleshooting steps that are listed here:

  Remove and reinstall iTunes and the components of the software for Windows 7 and later versions

  Thank you for using communities Support from Apple. See you soon!

• Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process.

  Firefox will not start after the upgrade to 27. Seen an error message during the upgrade process, but do not remember.
  Tried running firefox.exe Pei but error message:

  XML parsing error: the undefined entity
  Location: chrome://mozapps/content/profile/profileSelection.xul
  Line 18, column 1:
  "< dialog < =" "^ =" "p =" "> < / dialogue >

  Running on Windows XP SP3. No problem whatsoever before moving to 27. Sending of Chrome that I can't open Firefox at all.

  Thank you, jschaer2000. In the meantime, he works. How long, we'll see ;-)

• SE error message: "Run"DLL"there is a problem starting. C:\Users/John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll

  Get the below error message every time I start my computer:

  Run DLLS
  There was a problem starting
  C:\users\John\AppData\Local\Conduit\BackgroundContainer\BackgroundContainer.dll
  The specified module could not be found.

  Hello cuefox, thank you very much to judge me.
  We're here to help.
  Continue to browse the web with Firefox, thanks once more.

• Firefox does not start, no error message, only works in the background

  I click on Firefox it does not start
  no error message it does not start
  It works in the background in 32-bit
  I have re installed it but nothing changes

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls
  • https://support.Mozilla.org/KB/fix-problems-connecting-websites-after-updating