Envy 14-3010NR card wireless network problems

Similar Questions

• Wireless network problem: disconnects randomly anywhere between 1 and 4 hours.

  I have a wireless network problem, it disconnects randomly anywhere between 1 h and 4 h. The network consists of a Samsung 4 G hotspot and a Linksys AE1000. The signal strength is excellent, the AE1000 is 1 ft of the computer and 1 ft of the HotSpot.  The computer is a Dell Dimension 2400. Any ideas?

  Hi Jack,

  Problem solved.  I did 2 assumptions about the original problem.  I assumed that the 2 Tech that I spoke made the hurt their product. Battery saver has been activated on the hotspot.

  Thanks again

  Greg

• ERROR WITH "DELL WIRELESS WLAN CARD WIRELESS NETWORK CONTROLLER.

  GOT AN ERROR MESSAGE SAYING "DELL WIRELESS WLAN CARD WIRELESS NETWORK CONTROLLER STOPPED WORKING AND WAS CLOSED" AND NEED TO FIX. WHAT SHOULD I DO?

  Hello

  Actually try updating your driver and check with Dell Support and Forums if necessary.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  Dell - drivers
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Dell support
  http://support.Dell.com/

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• card 3160 AC wireless network problems

  Hello

  I bought a laptop HP Envy M6; product # G5N44UA #ABA running Windows 8.1 64-bit, and I have a problem with the wireless network card. It is a version of Intel dual-band AC3160 wireless 16.6.0.8

  The problem is that when I close the lid, do go to sleep or turn off the computer, it restarts when it says that it cannot connect. When I run the troubleshooting it says that there is something wrong with my (physical) access point. If I run the access point troubleshooting it reboots the access point which solves the problem, until he falls asleep again.

  What did I try? So far...

  (1) uninstalled and reinstalled the driver. No change.

  (2) changed some settings about «closing the lid» power management Changed for the 'status quo' when lid closes.

  Now when he goes to sleep or if there is, it does not detect the network at all unless I restart again.

  I changed the rear power settings, but I need to know if I have a hardware problem and how to get fixed.

  Thank you

  I was intrigued by the validations and proposed solutions to the question of the network adapter 3160.  I have a 8 month old G0T55AV of HP Envy 15 t-K000 Notebook 64-bit Win 8.1 with 12 GB of Ram, and of course the AC adapter / 3160 of Intel.  I should mention that I am a fan of long-time HP products.  It's my second computer of this model as first a miserably failed with Touch Pad questions and passing AC 3160 failures, if HP has requested that I return it and they were replaced by a new.  Shortly after I received my other 'News' that also came with the AC3160, I started having network disconnects when you wake up mode "Eve".  I found articles about uncheck the power saving mode.  That worked for a while and all of a sudden, I once again began to have problems.

  I contacted Tech Support Chat repeatedly and most recently of several days.  They diagnosed the problem and as usual tried to remove and download the drivers that had been made several times previously.  They also disabled several of my 'start-up' services and was intending to leave them turned off until I challenged, who also screwed up some of my services.  I also noticed that now I could not the PC to recognize the adapter in wake up.  I have to restart the PC to refresh and identify the adapter, a problem that I had not seen before.   If after all this, the recommendation was to perform a factory reset.  I objected, so I was sent a box to ship my computer in for 7-10 days service center where the reset would be carried out.  Of course, I had to delete all my data and it should reinstall all software installed after initially receiving the computer 8 months ago.  WHAT?  Of course, it would be no monetary cost to me; However, the grief of being without my PC and reload data and software has been a big emotional event.

  I took a chance to solve on my own.  HQ 3160 being an Intel product, I went to the page 'pilot' of the Intel website specifically for the AC 3160.  I noticed that the iteration of driver used by HP several iterations behind the current driver from Intel.  I tried using the program to automate the update of the Intel driver.  The program has identified the adapter such as the need to update; However, the pilot would not move through their utility.  Do not know why.  I finally found a link on their site which allowed me to download and install the most recent driver manually.  I've been running for almost a week and so far, I had no network card failures.  Without losing the connection on sleep, without losing the identity of the card, nothing.

  I do not claim that it would work in every situation of AC3160 has failed, but it seemed to work for me at least to date.  My shipping box to return my PC arrived Friday 2/13; However, I hold that the driver will continue to operate successfully.  This brings a few questions in mind:

  (1) why the HP Technical Support uses them most recent updated driver from the manufacturer?

  (2) why not HP own up to the fact that the AC3160 may be defective, issue a reminder and replace them?  I know the answer! $$$$$$$

  (3) why HP joined with Intel and provide a common solution to the end user?

  (4) why HP does not provide a specialty within Technical Support Group to deal only with issues AC3160 to prevent "groping" solutions that could potentially cause more harm than good?

• Original title: the connection card wireless network with windows 7 problem

  I have a dv6 Notebook PC HP clubhouse, 64-bit Windows 7 Home Premium, I bought end July2010. H-he detects the wireless network but will not connect. just if I'm until modem.but colse it smt connect to the deffernt wireless network. What is happening and where do I go to fix this problem.

  Hello

  1 have had any changes made on the computer before the show?

  2. do you get an error message when you try to connect to the wireless network connection?

  Method 1:

  First of all, I suggest for the link and try to run the troubleshooter and check if it helps.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  I suggest you to refer to the article and see if it helps:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

  Let us know if you need more assistance.

• Satellite A500-1GL - card wireless adapter problem

  Hi all

  I had a problem with the card wireless on my laptop for months and have no idea how solve more.

  Basically, the wireless card seems to go through phases does not turn on. One day I can boot up my laptop and it works fine, then the next day it won't work. The wireless button on the front of the laptop is turned on but don't turn on the red light.

  In the past, I've managed to get over this by several reboots the laptop (until he decides to work) or reinstall flash, wireless etc. drivers card drivers. However, none of these things today seem to be making a difference.

  The worst, it's that there is no continuity with when it does not work and how it is fixed (sometimes reboot once fixes it, other times reinstall drivers fix it and so on).

  For this reason, I assumed that this may mean that there is some sort of hardware failure? But if I run the laptop in safe mode, the wireless still works without any problem.

  Someone has an idea what is happening?

  Any help would be appreciated,

  Liam

  Hello

  First of all I would like to know what system you are using and if you have tried to recover the laptop to factory settings in the past.

  The point is that these issues are mostly related software and could be solved by resetting the system.

  However, I think you know that the wireless network card can be turned on and off using the FN + F8 key combination.
  Have you tried this combination in the past?

  Second, you must check the WLan card status in Device Manager.
  The point is that problems of card driver WLan, Wlan card doesn't would be not listed correctly in Device Manager. So this should be the next step.

  Where the Wlan card is listed correctly, I assume that the driver is installed and working properly.

• HP Envy 5530 scans more wireless network home but does not print

  Love my 5530 desire!

  Through our wireless network, it will scan at anything, but it only prints my smartphone and iMac. It will not print laptop Packard Bell with Windows 8 (although it will scan to it).

  Tried to re-install the drivers on the computer laptop etc etc, but, although printer printed initially - it has stopped after a month or two. Are there problems of network with Windows 8?

  Any ideas?

  Hello
  Try following the steps below and check if this can help:
  -Open the HP software by clicking on the HP Envy 5530 icon in the desktop or the Start Menu, and then click on the link to the Home Page of the printer (EWS).
  -Click on the network tab.
  -According to the model of your printer, click Network, click Network (IP) address or click IPv4 in the active network connection type.
  -Manuel IP-click and then click on suggest a manual IP address. An IP address manually, the subnet mask and default gateway shows.
  * Be sure to take note of the IP address and confirm the changes, and then close the EWS page.
  -Click the icon of 5530 desire within the desktop or the Start Menu and click the utilities tab, and then click Update IP address.
  -Type the IP address that is configured manually, click on save and confirm.
  -Open the control panel and go to devices and printers.
  -Right click on the HP Envy 5530 icon and select printer properties.
  -Open the Ports tab.
  -Click on the button Add Port, select Standard TCP/IP and click New Port.
  -Follow the procedure by typing the IP address that is configured manually and confirm the changes.

  Now try printing and check if the problem solved.

  Kind regards
  Shlomi

• Tecra 9100 wireless network problem

  I'll have a chance by putting my Tecra 9100 with my home wireless network. The network seems to work very well. My other laptop connects to it without any problems and I can connect the Tecra with the ethernet cable. But the wireless connection, it cannot be successfully established by the Tecra.

  She claims to be connected, but he receives no package, and could get no internet connectivity. When I try to 'fix' the connection, it sits there for a while before telling me that the IP address may not be renewed.

  I managed to connect the Tecra to the network of the next door without penalty, which suggests that there is some kind of problem with our network interface. I tried to reproduce the exact settings from my other laptop, so I don't understand what the problem is.

  Any idea would be appreciated with gratitude!

  Hello

  It's really not easy to say what is happening here. The functionality of the laptop is ok and it's very confusing if it works with other local wireless networks.

  I recommend putting your access point to the factory without some specific parameters settings and try to connect it.

  Sorry, but I don? have another idea.

• Hosted wireless network problem

  I'm currently located in a place where the WiFi you buy will only link with one device and the IP and MAC addresses to confirm the device before you connect to the internet. I am to avoid paying for both (laptop and smartphone) devices through a wireless network but my laptop using Microsoft Virtual WiFi Miniport Adapter. However, when I start the hosted network, either through the "netsh wlan start hostednetwork" command in the command prompt or via the software free virtual router Manager, my computer freezes completely and does not respond to anything except a hard stop. When I started this, everything worked well and I could use the network hosted without any problems, but in the last few weeks, I had to shut my computer down several times a day because of this problem. Can someone help me understand why my computer keeps freezing? Any help will be greatly appreciated.

  To help you, we suggest that you try to check on the link below:

  WiFi/SoftAP virtual fails to start with "the hosted network could not be started" on Windows 7 and Windows Server 2008 R2

  An update on the result.

• Hp1102w connection printer wireless network problems

  I can't get my connection between my Linksys WRT54G and my printer wireless hp1102w wireless. The configuration page shows the following: network not connected, I have a host name, hardware address. There is 0.0.0.0 for IPv4, the IP subnet mask & gateway IP. Configured IP said manual.

  Under wireless 802.1b/g/n: status: activated, common mode: infrastructure, my name network & authentic WPA/WPA2
  Under Direct Print Config: Off, HP-Print-40-Laser Jet 1102, Channel 6 and there is an IP v4 address. What should I do?

  Also my iPad4 does not see the hp1102w printer, do I have to download the software? I don't have a USB connection? I am very new to the Apple OS, if you couldn't tell.

  Salvation, TarNation,

  Welcome to the HP Forums, I hope you enjoy your experience!

  I understand that you are unable to set up the printer on the wireless network.

  I'll be happy to help you.

  Please provide the following information so that I can better help you.

  What operating system do you use?

  Mac OS X: how to find which Mac OS X Version is on my computer?

  You also have a PC?

  Once the printer is configured on the network, the Ipad connects on behalf of network from the router and the printer should allow you to print using Airpint. You don't need to download software for the Ipad.

  Thanks for posting on the HP Forums.
  Have a wonderful day!

• Satellite M45-165 - card wireless network not visible

  Hello world

  I am pleased to join this forum. I have trouble with the map on Satellite M45-S165 wireless. My friend has a M45-S165, he lost the recovery disc, I haved high new Windows XP SP2 but when complete the Windows Setup, the wireless card is invisible, like this:
  [http://i1023.photobucket.com/albums/af358/lonesomeboy/Anh%20hoc/wirelesserror.png]

  I do not have ' known reason, can you help me solve this problem? Thanks in advanced for any help

  Hi lemon tree,.

  Have you checked the Device Manager If WLAN card is on the list? Maybe just the driver is missing, so it s not listed in network connections.
  More recent WLAN driver download on the official website of Toshiba.

  By the way: why you installed SP2 only? There is already a SP3 for XP it is important because it corrects a lot of security problems.

• Wireless network problem

  When I start my Dell laptop that is running Windows XP, it will not connect to wireless (Intel PROSet).  When I try to connect to my network, I get the message "another application is controlling the wireless card." If I disable the wireless computer, restart the computer and then enable the wireless connection, I can connect to the network.  I updated the driver, but it does not help.

  IIRC, if you are using Intel PROSet you should not normally the 'Wireless Zero Configuration' (WZC) that Microsoft provides.  Maybe it's the "other application" that controls the wireless card.  Try to disable the service 'Wireless Zero Configuration' and see if the problem goes away.  To disable the automatic configuration service, perform the following steps, noting the current settings in case you need to go back:

  1. Start-> Run-> "services.msc".
  2. Locate the "Wireless Zero Configuration" line on the window that opens, and double-click
  3. Change the "Startup Type" to "Disabled" and if its status is "started", then click on the 'Stop' button to stop.

  HTH,
  JW

• LOCAL M40X-230 WIRELESS NETWORK PROBLEM

  I have a problem with the Wi - Fi connection. After initial startup of wireless lan, speed goes from 54 to 1 MB/s and then continues to jump around making me lose my internet connection. Thought it was the router at first but after 3 new routers, this may not be the case. Last router is liksys wag54gs. Laptop is about 7 feet from the router. Please, I need help!

  Hello, Robert

  On this forum, you can find many topics on the same theme. You can check wireless Board. Check please what a http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=8406

  There is obviously a problem with the Intel wireless card.

• Impossible to activate the card wireless network on Satellite L10-202

  Hello

  I have a portable Satellite L10 that comes without WLAN.
  I bought and installed an Intel pro wireless 2200BG card on the MiniPCi slot. I have also installed and connected the mini-antennes.

  The device is activated but does not connect. I installed ConfigFree and the result was: "status of Communication Wireless: OFF." Switch where the arrow is pointing. "My laptop does not have this button, a plastic cap is here.

  Also, the combination FN + F8 does nothing.
  How can I solve this problem?
  How can I put it ON without having this button?

  Thank you.

  Hello, Lucy

  I tried to find the hardware configuration of your Satellite L10 202 (PSL10E) and now I'm complete confused now. I didn t find any information that this model of phone is upgradable WIFI and I do not understand that antenna WLAN is here.

  Anyway, is recognized WLAN antenna correctly in Device Manager?

• Satellite C660 - no card wireless network in Device Manager

  I had a Satellite C660 for months with a preinstalled operating system.
  I've never had a problem with my wireless until recent days.

  I checked Device Manager and it seems that the wireless card is missing,
  I tried reinstalling the drivers but it stops immediately after extraction.

  I did a full scan and found nothing, I am at a loss,

  Thanks in advance for your help,

  Andy.

  Hello

  You see yellow exclamation points or unknown devices in Device Manager?
  These devices will appear if the driver is not installed correctly.

  Otherwise, it might be possible that Wlan module is dead.