Equium laptop computer connects cable but not wireless

Similar Questions

• C6380 - computer laptop xp prints with connection by usb cable but not wireless

  Hello

  I have a c6380, which is about two weeks old. Setup worked fine when I put it on the wireless network and everything is ok.

  I installed the software on a vista pc which is connected by cable to my router from sky. This shows very well.

  I installed the software on a computer vista laptop that is wireless and prints well.

  I also have a computer laptop xp. It is also wireless. The software installed without problem. See the printer etc. However, when I try and print, the printer makes noise and pulls the paper, then the screen says it's printing and then nothing happens. The printer stays like that and eventually the laptop shows a failure to print the message. The document remains in the print queue before deletion, and I have to press Cancel on the printer. If I plug the printer with a usb cable for this laptopit prints without problem.

  I ping the printer wireless froom the laptop xp and access the admin screen. It also shows as a network drive in my computer.

  I uninstalled the software that came with the printer, downloaded the hp software to ensure that it is up-to-date and re installed.

  I put the printer with a static ip address.

  I restarted the router as well.

  The router uses a channel 11 broadcast key, wpa - psk and is set to g & b modes.

  Now, it's really really frustrating because the computer laptop xp my wife, is the main reason why we bought a wirelsss printer because she is a teacher and done loads of printing.

  I'm pretty good with pc / networks etc but have now run out of ideas.

  Can someone help me please?

  Thanks in advance.

  Steve

  Hello

  I've actually solved myself, but I'll keep this post here anyway.

  The answer has been upgraded from SP2 to SP3.

  Probably should have thought about that a little bit earlier!

• C7250 connected wireless works with wired ethernet PC but not wireless PC

  C7250 installs fine with static IP address and wired (ethernet) PC works perfectly, but is not recognized by the PC wireless.

  Can ping the IP of the PC cable but not wireless computers.

  Can connect to the IP address of the browser and can logon to the wired PCs of wireless computers.

  When the wireless PC is connected to the network with ethernet cable the C7250 works perfectly.

  Firewall is not the issue because I tested with the firewall disabled.

  Any suggestions?

  Thank you for your help.

  I FINALLY FOUND a RESOLUTION but let me describe what I've done to isolate the problem so that others will not do the same things I did.

  I used my Windows CE PDA and connected to the wireless router. I made sure that IE could access a different print server wired for a Brother HL-2140 I 192.168.2.10 and it worked. Who checked out that IE was working with a wired device. I then went to Yahoo!, and it worked. Then, I tried to access the C7250 configuration using IP 192.168.2.20 address in IE and it failed. (I checked with my Wired PC I could have access to the configuration of C7250 via IE.) I expected this result.

  Then I connected the PDA via USB and verified that I could use it to access the configuration of C7250 use IE on the PDA and it worked.

  I then tested between two wireless PC. Could not connect to each other through the router. But if one of them has been wired and one wireless they connected and I have consulted the disks between computers. I also tested the two cables with the same results.

  THE PROBLEM WAS IN THE ROUTER.

  These tests again virtually eliminated all PC, firewalls (since I've tested with the firewall disabled), the C7250 and the print server for the HL2140 brother as being the source of the problems.

  I then updated the firmware of the router to the latest version and repeated all the tests carried out in the complete thread and had the same results.

  RESOLUTION:
  The router I was using was a Linksys WRT54GS Ver 1.

  I also had a backup router which is a Linksys WRT54GS 7 worm that had the same settings as the Router 1 worm.

  I changed the SSID of the original router (Ver 1) so I would not need to change the SSID in all my devices during testing with the router Ver 7.

  I checked the firmware on the router worm 7 was the later and pulled up.

  The first test I did was to use a ping wireless PC the C7250 192.168.2.20 and it worked!

  I then used the wireless PC and IE to access the configuration of C7250 192.168.2.20 and it worked!

  I then checked the port for the C7250 was still a TCP/IP port to 192.168.2.20 and sent a test page to the printer and it worked!

  I consulted quickly wireless configuration C7250 and printer a test of a PC cable page and that worked!

  Finally, I tested PC wireless wireless PC PCand wired PC and the dirves successfully in both directions and checked that PC wired to wired PC was still working as before.

  All that remained was to supply two routers and router swap 1 worm with the Ver 7 router and rerun the tests with the router to Ver 7 manage my real network. Everything works as it should.

  I'll keep Router 1 worm as a backup to the Ver 7 knowing router unless the router worm 7 does not only feature that I lose when I reinstall the Router 1 worm is wireless connectivity to wireless, and I can temporarily work around until I get another router that is likely to be a "n" because what is have is ' G;

  THANK YOU FOR ALL YOUR HELP PRINTDOC!

  PRINTDOC BRAVO!

• My HP Pavilion laptop computer 1b60us g6 will not activate al all!

  My HP Pavilion laptop computer 1b60us g6 will not activate al all! I tried my battery in another laptop and it works fine and my charger.  I also tried another charger on my laptop and nothing! It worked fine the other day and now nothing today! I tried all the suggestions now down the power button for 15-30 seconds without AC or battery and still nothing. I have really important things on my computer. It can be saved? HELP ME PLEASE!

  Click on the link. It is a hard drive that goes inside the computer into a disk external usb. The card costs less than $15. It's a beautiful piece of grear to have around.

  If it's 'the Answer', click on 'Accept as Solution' while others may find it.

• XP SP3 laptop computer connects to various WiFi hotspots but not to an individual.

  Just upgraded to Verizon MiFi 2200 MiFi 4620 the personal hotspot.  Our other Office XP SP3 computer, a Windows 7 laptop and Tablet Android ASUS everything automatically detected and entering the network key/password, all connected to the hotspot and the WWW.

  Fortunately, the XP SP3 laptop connects to other WiFi hotspots and will always connect to the MiFi 2200 old if it is powered even if, of course, he cannot access the WWW, because Verizon's network no longer recognizes the 2200 due service is transferred to the new 4620 MiFi.

  The XP SP3 laptop detects the new hotspot very well.  The command 'View available wireless networks' shows the new hotspot, but when 'Connect' is attempted he goes just in the cycle to appear in the connection, but returned eventually to view available wireless networks.  The 'Connect' button is available, implying that it would connect so click on new.

  Use the same settings (SSID, password, encryption, etc) for the device problem than others who work as they should.  It seems to be an incorrect setting or adjustment in the laptop but I can not understand that one.  I compared the services running on two XP machines and have found no obvious inadequacy.

  Advice?

  Thank you!

  When you say that the new device has the same encryption, do you mean that you know that both old and new devices use the same type of encryption (for example, WPA2, WPA, WPA-TKIP, etc.)?

  I noticed the following two statements in the Guide of the user for the MiFi 4620 L (page 30)

  • WPA/WPA2 Personal joint (safer, less compatible with older devices)
  • IMPORTANT you must use the profile secured with WPA/WPA2 Personal Mode security settings mixed when possible.

  Suggesting that the MiFi 4620 can by default that set... and that the hardware in your computer laptop problem is one of the 'old' devices that is not compatible with this setting.

  Just as an experiment, temporarily configure the MiFi to 'Open' (see pages 30 et seq.) and see if your laptop can connect.

• Can connect to internet when wired, but not wireless

  Just restarted my computer laptop and now unable to connect to the internet.via my wireless router. Am connected to the router, but not the router to the internet. Can connect to the internet by a cable in the router to my laptop. The computer identifies the network correctly when it is wired, but shows as not identified during the use of the wireless router. Already fed the moden and router down twice, without change. other phones that I use are able to access the intwrnet via the wireless router, so I think it has to do with the system restart I just did on this laptop. Any ideas would be helpful

  Hello

  You did it all changes on the computer (which is originally this issue) before this problem?

  Read the following article that may help you.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Connected to home WiFi but not Wireless LAN home page

  This morning, everything was fine but something happened with the printer and now my laptop is all out of whack. I used to be connected to my home network where I could access all computers on the network and my hard drive Western Digital World Book Edition II. I don't know how, but now I'm out of the network. I'm always connected to the WiFi which is available in the House but I can ' t do anything else. I can't watch other computers, print or watch the WD hard drive. I tried everything to get me back on the network, but not luck.

  I am using the following:
  -IBM ThinkPad X 41 Tablet running Windows XP
  -Linksys Wireless-N Broadband Router (model number - WRT300N v1.1)
  -Canon PIXMA MX870
  -Western Digital myBook World Edition II (2 TB)

  I did steps 1 to 6, but he says still unknown

  Sorry if I wasn't clear.

  1-6 steps enable NetBIOS over TCP/IP, which is a good thing to do.  These measures do not affect the type of node.  As explained in the link nitecruzr, there is a good reason to make this explicit parameter instead of the default Windows.

  Reset the 'unknown' to 'Broadcast' node type can be performed by following the steps in KB903267 - but it is I think remember that sometimes the steps described in this article do not work and the type of node is still 'unknown '.  What I meant is that it is OK for the type of node be 'unknown '.

• Cannot resolve IP # so unable to connect to the internet on my laptop. Can diagnose, but not repair. Why?

  I have windows xp on the desktop & windows vista on computer dell laptop. For some reason unable to connect to internet on laptop, I took it on vacation.  I wasn't able to get on the internet for 2 weeks at the home of parents therefore had to use his laptop with his internet connection.  I have locked up something on my own.  Office IP #192.168.1.1 but phone's IP #192.168.1.0. What can I do? Thank you

  Hello Bamzplaces,

  Thanks for posting in the Microsoft Answers forum! The IP address of your laptop must be assigned by DHCP through your router. Proceed as follows to make sure that your laptop computer to obtain an IP address automatically:

  ·          Open network and sharing Center via Control Panel or by double-clicking on network control and select Properties.

  ·          Click on to view the status of

  ·          Click on Properties

  ·          When Windows asks your permission to continue, click continue .

  ·          Select Internet Protocol Version 4 (TCP/IPv4) , and then click Properties

  ·          Verify that the obtain an IP address automatically and DNS server obtain an address automatically are selected.

  ·          Follow the same steps for the connection of your Internet Version 6 (TCP/IPv4) Protocol

  ·          Click OK and exit to the desktop.

  I would then recycle your adapter to disconnect manually for 10 to 20 seconds and then reconnect. Your connection once we connected is displayed, try to connect to the internet.

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Computer connects to the network wireless as "local only".

  I am running Vista Home Premium SP2 on a HP Pavilion laptop.  I've never had any problems to connect this machine to a wireless network before, in hotels, at home, or anywhere.  My current home network is a modem - cable-> wireless-> wireless netgear n300 router.  My laptop connects to the internet via the modem cable directly or a wire from the netgear router.  I have a second, almost cell identical (it's intel, while the one who does not is AMD) which connects to the network wireless without any problem.  Two iphones connected wirelessely without any problem.  My HP laptop is the only one who refuses to connect to the internet.  Connected to the wireless network, it has access "local only".

  I tried the solution in this article: http://support.microsoft.com/kb/928233

  The question does not seem to receive an ip address, the computer receives an ip address.  I have disabled the IP v6, ran the norton removal tool, because I only had to a point and tried all other suggestions in these discussions: http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/0949042d-074e-43ab-ba95-3c06cc2aa6be and http://social.answers.microsoft.com/Forums/en-US/vistanetworking/thread/bc08f0e7-49a9-4458-9e0e-149b2df362ec.  I've uninstalled and reinstalled the adapter and all TCP/IP and network protocols associated with it.  I am at a loss and would welcome any ideas.

  Here is the result of the command ipconfig / all:

  Windows IP configuration

  Name of the host...: Arrakis

  Primary Dns suffix...:

  Node... type: broadcast

  Active... IP routing: No.

  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :

  ... Description: Atheros AR5007 802. 11 b / g WiFi adapt

  Physical address.... : 00-1E-4C-B2-32-BC

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  IPv4 address: 192.168.1.5 (Preferred)

  ... Subnet mask: 255.255.255.0.

  Lease obtained...: Wednesday, 28 April 2010 21:40:55

  End of the lease...: Thursday, April 29, 2010 21:40:55

  ... Default gateway. : 192.168.1.1.

  DHCP server...: 192.168.1.1.

  DNS servers...: 192.168.1.1.

  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: NVIDIA nForce Networking Controller

  Physical address.... : 00-1B-24-FA-DA-80

  DHCP active...: Yes

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 10:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {31C080CE-FE0B-4D50-B734-C782C9A25FBC}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: isatap. {B198B0D3-B70A-4E3E-858D-9774C414EECD}

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Teredo Tunneling Pseudo-Interface

  Physical address.... : 02-00-54-55-4E-01

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected

  The connection-specific DNS suffix. :

  ... Description: Card 6TO4

  Physical address.... : 00-00-00-00-00-00-00-E0

  DHCP active...: No.

  Autoconfiguration enabled...: Yes

  If anyone has this problem, it has been resolved by rolling the security settings on the router WEP.  I got the answer from the support client netgear.

  Amazing how two iphones, another laptop with XP and a laptop running Ubuntu Linux all about them without any problem, but wouldn't connect Vista laptop.

• Laptop computer connection problems Toshiba for HP Officejet Pro 8610

  Hi, I just unpacked my new HP Officejet Pro 8610 and after close to two hours still unable to connect it with my laptop.  I have a Toshiba Satellite S55 A5257 8.1 Windows running.  The printer shows that it is connected to the correct network (with no other network name of the network).  I tried setting up with the normal settings, then with firewall disabled, then with the firewall and antivirus, stop and went through all the suggestions on the software to solve problems of installation failure that has been suggested to install.  Have also tried to turn the router off and on again and also turn off the laptop and turn it on again.  Also the printer is off and turned it back.

  I'd be more than happy to try other suggestions that anyone could have.

  Update: a little while later, I have at least been able to print using a usb cable, but is not always wireless.

  Hi Jimbo867,

  Welcome to the HP Forums!

  I see that your HP Officejet pro 8610 does not connect to your Windows 8.1 with a Wi - Fi connection. I'm happy to help you with this problem of connection!

  Please see the following guides:

  1. "Can't find the printer" message appears on the computer during a Network Installation.
  2. The printer keeps Wi-Fi connection.

  I hope this solves your problem and I thank you for posting!

• Direct print from laptop computer connection

  I have a laptop HP with windows 7 32 bit and the designjet 650 c B model with an installed direct jet card, so I a usb converter cable network I want to print from a usb port or from the port of network cable. I just want to know what is called the port that I use? Help, please!

  You have a wireless router?  I have a Designjet 650 c connected to my router with a LAN cable, can I access the 650 c of my HP laptop wireless via the router.

  If you follow this path, you will get an IP address for the Designjet 650 c by selecting Prev in the menu until you get to the entrance, the top menu can go down three times for installing I/O, entry, entry (modular), entrance (network Cfg = >), down Yes, Prev, Prev, Prev, entrance, entry, down arrow twice for utilities Entry, arrow down twice for Config plot, Enter.

  That you select the jetdirect card like I/O device, get an IP address from the router and then print a configuration page that displays the IP address to halfway to the bottom of the page.

  On laptop computer click Start, devices and printers, do a right-click on the Designjet 650 c, printer, port properties, add a Port, Port TCP/IP Standard, new Port, following, then enter the IP config page printed.  For me, it comes to 192.168.1.13.  Enter the appropriate value, Next, Finish.

  If you do not have a router then consider making an inexpensive wireless router that could be wired to the Designjet and wireless for the laptop.  It would probably be a much better solution than to try to make a converter USB - lan.

• WRT320N laptop computer connection issues

  Hi all

  I decided to upgrade my router today to WRT320N. I connect 2 computers wired, wireless 3 computers and a printer of HP Network on a home network. I was able to get the wired machines and the printer goes very well with Windows Vista and the Linksys software. I could not connect wireless laptops. I used the Network Magic program, the Vista network program and the HP Wireless asst without success. I tried using auto detect it on the router, to connect directly from the computer to a wireless network and using the magic network programs, including manual connect and the parameters on a loading USB device and try this on the computer to connect. I'm at my wit's end! Ideas by steps out there on what to do? I rebooted the router and Comcast cable modem x 2 x 4 and all computers at least once. Thank you.

  Tom Brown

  Using Comcast surfboard Motorola Modem (phone, internet) Multi model SBV5220

  Network Magic 5.5.9195.0 - Pure0.LinksysRouterSetup Version

  Operating system is Windows Vista Home Premium w / SP1 32-bit

  Windows Firewall in use

  AVG 9.0 antivirus

  SuperAntiSpyware 4.29. 1004, core 4046 track 1986

  Router WRT320N, firmware 1.0.03 build 010, address Internet IP = 76.103.67.182

  I hope this helps.

  Hi, do you have Network Lock active?  If so, disable it, and then try to connect to your laptop.

• Windows Vista connected online but not shown on network and sharing Center or on the taskbar, leads to other problems

  I have a Dell Inspiron 1520 running on Windows Vista, my router modem is a Motorola SURFboard SBG901. A few months ago on this computer, I couldn't see that I was connected online either from right down icon in my taskbar (it shows just two monitors with an 'x', that when you highlight on he says "not connected, you are currently not connected to any network.")  I don't see it on my network and sharing Center which States: "not connected wireless connections are available." In terms of network it shows that my PC and then the line that has an x on him. If you click the x, or select diagnose and repair, he informs me that all is going well with my computer. If I go to connect to a wireless network, it shows that I'm connected to my network ready. I open one of my browsers and they all work very well, I can access any site without problem. I was not embarrassed with him at the time, but since then I moved into a new House and have a new service and everything, with this motorola modem cable. my new wireless network is a network unsecured, which of course, I want to fix it. I can connect to this network, but I can't access it through Windows properties to make sure. I read the manual of the modem, telling me to connect through an ethernet connection and access configuration manager using the ip address of my router on a browser, but which does not charge or the other. I have other devices (Ipod Touch and PS3) wireless I got other people come computers and they all detect the network but cannot connect to it. Thanks for any help.

  Hello
   
   
  I would like to ask you a few more things.
  1. how many network connections you have created?
  2. are there multiple NICs installed on the computer?
   
   
  Since this is a common problem and many users have solved this problem by using different methods.
   
  This can also occur if you frequently use several type of internet connections such as dial-up, Ethernet and LAN.
   
  As the article below also indicates that there could be multiple reasons for the same.
  The network adapter icon incorrectly displays a red "X" in the window management in Windows Vista network connections when the network adapter is connected
  http://support.Microsoft.com/kb/945925
   
   
  Method 1.
  I ask you to remove any network connection if you have created and then check.
   
   
  Method 2.
  For control please check in mode safe mode with Networking if the problem exists.
  Here's how:

  a. restart your computer.
  b. when the computer starts, you will see your computer hardware are listed. When you see this information begins to tap the F8 on your keyboard key repeatedly until you are presented with the screen Windows 7 Advanced Startup Options.
  c. using the arrow keys, select the desired option of Mode without failure.
  d. press the Enter key on your keyboard to boot mode safe mode of Windows 7 with networking.
  e. when Windows starts, use check and Internet explore if the problem persists.

  For more information, see the articles below.

  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

   

  Troubleshooting in safe mode
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshooting-problems-while-in-safe-mode
   
   
  I hope this helps.
   

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Display problem laptop computer connecting to the TV via HDMI

  I have a Satellite L500 - 19 X and when I connect the laptop to my Sony's Bravia TV, the screen is constantly restless.

  I tried to change the refresh rate, but that did not help. The HDMI cable should not be the problem, because it works very well with my Xbox. The problem is there for both in dual display and expand options display.

  Someone else has the same problem and found a solution?

  Thank you

  > That's the problem for both in dual display and expand options display.
  And when you see the desktop on the TV only?

• HP laptop computer 635: need driver for wireless router

  Hello. I had to replace the hard drive of my laptop computer and a new operating system, Windows 7 Pro, after which it cannot connect to the wireless router. It's a router Westell A90-750018-07. I have a Tablet Android working on this particular router and want to download the driver on it and put it on the flash drive to reinstall on my laptop. Is that going to work? Where can I download it? FairPoint is now 14.99 an extra month of me now for a Support technique Premium. They are waiting for me to borrow a laptop to try to help him to do so. They seek to use the android on the phone, but it seemed to complicated with android as a third party. Will this work? Please if someone could help would be great. Thank you.

  You need the driver for the card installed in your 635 wireless. Problem is that you will know which card you have Ralink, Realtek or Atheros. The drivers are all posted on your support page:

  http://h20564.www2.HP.com/hpsc/SWD/public/readIndex?sp4ts.Oid=5086540&swLangOid=8&swEnvOid=4059

  If you don't know what wireless card, you need to get the id of the hardware in the Device Manager. Right-click the network adapter, choose Proprietes.dans the window that opens click on the Details tab use the selector drop-down menu to choose the hardware id. After the first string of numbers - or at least the first half of the chain.