Equium M50 connect to the WLan router only when security is disabled

Similar Questions

• Satellite A110-195 unable to connect to the WLan router

  Hello

  I have a wifi router and I have connected my laptop and it worked wery well but on low there is I could not conect to router but woudn't ip address pop up. Internet access was not.
  I am connected to the same router another device and it worked...

  Hello

  Believe me, there is no general solution, you must check all the settings of your operating system

  First of all that I recommend to check the parameters of the TCP/IP protocol if everything is settled automatically on.
  Then check if you are using encryption parameters right as standard (WEP, WPA, WPA2) encryption and the encryption key.

  It s also advised to reinstall or update the Wlan card driver

  If you used the windows own WLan configuration, I would recommend testing as Atheros Client utility or Intel ProSet Wlan client configuration utility. But it depends on the WLan card what client WLan configuration utility can be used

  concerning

• Satellite L40 - 14N does not connect to the WLan router

  Bought two portable Satellite L40 - 14N as Christmas gifts and one of them does not connect to the wireless router.
  Is the error that says "error message unknown" try please login again.

  The wireless network appears in the list of networks available with a strong signal. Notepad attempts to connect but the error 'wireless link failed for an unknown reason. " Made a comparison with the other laptop that works very well and the configurations appear to be identical!

  Tried it on wireless network from a friend with the same result. All suggestions, am pulling out my hair at this point.

  Seems to be a Vista issue.

  I found this article Ms knowledge base:
  http://support.Microsoft.com/kb/928233/en-us

  You need to add a value in the Windows registry.

  1. Click Start, type regedit in the search box, and then click regedit
  list programs.

  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE es\Tcpip\Parameters\Interfaces\ {GUID}
  This registry path, click the (GUID) subkey that corresponds to the
  Network adapter that is connected to the network.

  3. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  4 new value #1, enter DhcpConnEnableBcastFlagToggle, then
  Press ENTER.

  5. right click on DhcpConnEnableBcastFlagToggle, then click on modify.

  6. in the value data box, type 1 and then click OK.

  7. close the registry editor.

  concerning

• Equium L10-200 - unable to connect to the WLan router

  I have a 200 L10
  When I tried to connect WiFi my suburb does not connect with the router at all. Looks like it was trying to access the Internet.
  Then window took to replace my IP address. But as I can not connect on it cannot be a substitute.

  How can I get them back.
  Cable and work for laptop computer to my wife on the same router work ok.

  I am running XP and connect to the sky

  Hey mate,

  Why you can t replace your IP address?
  First to connect properly, check if you need a static IP address or if you get an IP address from your router (DHCP).

  If you use encryption, make sure you typed the correct password. Disable filtering of MAC addresses in the router to connect properly.

  Last but not least, make sure that you have installed the new firmware on your router.

• Unable to connect to the WLAN router satellite P300

  Hello everyone,

  I hope you can help me with my problem.

  I bought a Satellite P300. Now, I'll have some connection problems to my fritzboxfonwlan over a wlan network.

  When I connect my laptop via a cable, all right. Only with wlan i´m problems.
  My router ssid is displayed correctly. I can also type the key. But then the router is not to be found.

  I use as wpa2 encryption.
  I think that Vista has problems with it. Vista has also the most recent updates and my wireless (intel agn5100) card.
  I tried all the three drivers on the side of toshiba. I Don t know what I can do next.

  If you have any ideas, I'll be happy to hear it.

  Hello

  Have you checked if the address Mac filtering settings can affect the WLan functionality?
  If the MAC address filtering enabled your WLan card mac address has been inserted, then your laptop wouldn't connect.

  Also I recommend you check the settings of the WLan card TCP/IP.
  In the TCP/IP properties, you must set options for automatically

  PS: have you checked whether your P300 is the latest BIOS?

• Qosmio X 300-13 G - unable to connect to the WLan router using Project N

  Hello
  I purchased a Qosmio X 300-13 g (the only one available in Portugal :/) and I tried to connect it to a network wirelles N, but I always get an error message):
  Windows could not connect because the defenitions of the router are different from your...

  Well you know why? I tried with several routers, and it is always the same...

  TKS

  Concerning

  Is your WLan router supports 802.11 N draft standard?

  Did you choose N draft standard on your WLan router?

• Satellite Pro 6100 - unable to connect to the WLAN router

  Hello

  I brought a 2nd hand Satellite Pro, model version SP6100 (PS610E-029ZV-EN), P4 1.7 Ghz, 512 MB, 30 GB, with Windows 2000 Pro loaded.

  I can't connect to my wireless router. The switch is in the correct position.

  I want to change to XP using the key provided with the new laptop (dual OS) however I can't reformat using a XP disc at the start up or if I use the recovery cd (start with holding C and let go when he works up) it starts but displays 'specification drive not valid' three times and charges Win2000.

  Can someone advise how (or if!) Can I reformat I want?

  Any help will be greatly appreciated.
  See you soon.

  Are you sure that the wireless network adapter has been installed in the laptop?
  Check in Device Manager

  On some series WLan is optional. This means that the WLan card is not installed, but it is possible to install an and, consequently, the laptop contains the WLan switch.

• Desktop connects to the local wifi only, when the netbook to connect to internet

  Hello. My netbook and phone connect to wireless internet, no problem with my wifi network. And until recently my desktop computer connected ok too, using a usb adapter. However, I now have a problem. my pc connects to the wireless network, but only locally. Can anyone help please? There must be a setting that I or someone has changed?

  Hello

  You did changes to the computer before the show?

  Method 1: I suggest you temporarily disable the antivirus software or firewall and check if it helps:

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  Warning: turn off Windows Firewall/antivirus can make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.

  Method 2: reset the default router and check if this solves the problem:

  Next to the electric power plug, there is a pinhole reset button. Remove all the cables from your router except the power cord. Press reset button with a PIN for 10 seconds. Wait 10 seconds then unplug the router. Router will be at default values, reinstall using the software that came with the router. You may need to reinstall the software of NIC as well. Then write your password on a piece of tape and stick it to your router.

  Method 3: Try the steps in the link and see if it helps:

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Reference: Wired and wireless in Windows network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 4: Try the steps from the link and see if it makes a difference:

  Of network connectivity status incorrectly as 'Local' only on a Windows Server 2008 or Windows Vista-based computer that has multiple network cards

  http://support.Microsoft.com/kb/947041

• Satellite P200 - unable to connect to the WLAN router

  I have a Satellite P200 and that you have upgraded from Vista to Windows 7.

  The wireless is working and to see available networks, but trying to connect it does not ask the WEP key, it just says: he has a connection problem and (possibly) says that it cannot connect.

  Someone at - it clues on this?

  Thank you.

  Hello!

  It's really strange Mavourneen. I also have Windows 7 on my Toshiba laptop, but I put t have problems to connect to my router WLAN. Everything works fine on it.

  Can I ask you if you tried to update the driver WLAN? You can download the latest version here:
  http://APS2.toshiba-tro.de/WLAN/

  Have you tried to update the BIOS?

• Satellite L500D - unable to connect to the WLAN router

  Hey all,.

  Hoping that someone here will be more help. For some reason, my laptop won't connect to a wireless network today and it was working fine yesterday.
  When I troubleshoot I get: there might be a problem with the wireless network connection card

  I called belkin and the Lady reset our wireless under a new name which we I = didn t need that my roommate who has vista had no problems with his internet. When I connect the cable through my laptop, I have internet

  Now that I see there no button on my phone to activate the wireless it connected always automatically and the led is on.

  Hi Ren,

  In the wireless issues forum, you can find hundreds of discussions on different WLAN problems.
  Did you check that?
  I think that you will find your answer.

  According to your assignment on resets the router I think that it s properly configured. Check the router security options if the SSID is visible and then encryption and password. Also, make sure that the MAC address filtering is not enabled.

• Satellite Pro A40 can't connect to the WLan using the Win XP

  Hi all

  Newbie on your site so thank you in advance for your answers ;-)

  Picked up a Toshiba Satellite Pro A40, completely formatted and installed a legal XP Pro.

  Trying to connect to the internet using a Netgear wg511 card works on my other laptop, it will not connect even though I installed the driver for it?

  It comes up with 'limited or no connectivity problem occurred because the network has not assigned a network address of the computer.

  Any ideas please?

  Thanks Mike

  Hello

  First of all, you must update the WLan driver.
  I put t know what wireless network card has been installed, but you can find WLan card details in Device Manager-> network adapters.

  In addition, I recommend to disable all the security settings on the router and then try to connect to the wireless network.
  If you will be able to connect to the Wlan, you can enable security settings (Wlan encryption, mac address filtering, firewall, etc.) again.

  Last but not least, you can try to use this command in a DOS (CMD)
  Ipconfig / renew

  Big names

• Satellite M70: I can't connect to the WLan access point

  I have several wireless laptops, all work fine - except my M70.
  I use Intel Proset, and he sees the access point, but says "unable to connect" when I try.
  The signal is high (2 meters distance).

  I tried with WEP, WPA and without security. I am absolutely convinced that I entered the right keys.
  The access point is a Belkin Pre - N-, but I tried with a point of access 3Com, with the same problem - my Ipaq, my other PC, and all guests can connect,- but not my Toshiba!
  The wireless card is the standard Intel, with the latest driver from October 2006 intalled.

  Getting desperate...

  Hello

  If you get a signal strong, so I guess that the laptop is already connected to the access point. Or am I wrong?
  On my laptop, the computer WLan small icon appears only if I connected to the Wlan and then I can see the State of the signal.

  However, you suggested to use the Intel Proset utility to configure the WiFi network but on the clean Windows configuration. Have you tested it?

  This question seems very strange to me.
  Sometimes it of not possible to connect the WiFi network because of poor compatibility between the router and wireless network card.
  My router supports Wlan AB mode and my second card for computer laptop support BG.
  That's why I m not able to connect to the Wlan. Maybe it s also your case.

  On my router, I can also put the MAC address filtering. You should check this option on your router.
  But generally it is not easy to say why it happens. You know you should check every single option and if it s not possible so I guess that it s a compatibility issue.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• S70 - A satellite fails to connect to the WLan

  Hi all

  Here I am having big problems with my connection Wireless on my S70 - A

  The connection continues to be cut off unexpectedly (like a reset of the network card) to find an internet connection that I have to turn off the wifi and re-connect manually...
  Of + WIFI signal LOW everything which is my distance with my box.

  The PC detects my wifi signal (it seems to be the most), I click on it to connect and then I fall directly on the 2 bars of reception! of course my wifi settings and keys are configured correctly...
  The PC is new, dating back to June 2014.

  Here's the conf:

  S70 - A SATELLITE
  WINDOWS 8.1 6.3.9600
  BIOS VERSION: 1.60
  processor Intel core 2.4 GHZ CPU I7-4700MQ

  Microsoft Virtual wifi adapter Direct
  Adapter type: IEEE 802.11 wireless
  Qualcomm-Atheros AR956x Wireless Network adapt
  Adapter type: IEEE 802.11 wireless
  Qualcomm-Atheros AR8161 PCI - E Gigabit Ethernet Controller (NDIS 6.30)
  Adapter type: Ethernet
  Software Loopback Interface 1
  Adapter type: Loopback
  DRIVER DATE: 11/2013

  If someone had an idea, should I a fair gift NIC? or something to change...

  Thank you in advance for your help, regards

  The weak WiFi signal could be related to parameters that are in energy saving Windows power management.

  It of possible to change the power to save the settings for different portable devices and generally depends on the use of the laptop. In case you use the battery mode, you can change the setting to increase the battery working time. But generally, this affects the performance of the device.

  Here's a nice technical document how to manage these settings (it of currently for Win 7 but very similar to Win 8 or 8.1 Win)
  http://APS2.toshiba-tro.de/KB0/HTD12017W0001R01.htm

  I recommend you to choose the most efficient setting of PCI Express wireless adapter settings
  By the way: in many cases its helpful to change the configuration of the WLan router. Try to use different channels (1-11) and different encryption (WPA / WPA2 TKIP AES)

• MacMini don't auto connect to the preferred wireless network when the router reboots

  My MacMini is located to join my favorite wifi network. Where I stay, there is usually a power failure close to a minute or two during the day.

  My setup is such that my MacMini running 24 x 7 with a backup uninterruptible but my router (AirPort Express) turns off during the power outage. When the router goes off, my Mac disconnects from the network which should, but now when my router turns, the MacMini reconnect to the preferred network.

  It shows the network preferred list, and when I manually click on this subject, it reconnects immediately without asking for password. But this will not happen automatically.

  If I restart my MacMini it reconnects very well. The problem occurs only when my MacMini is but my router restarts.

  To reproduce this problem on your side, just turn off your router and once your Mac disconnects from the network back on the router. See if your mac reconnects to your wifi fine.

  Any solution or advice for this problem?

  Thank you.

  Please test after taking each of the steps that you have not already tried it. Stop when the problem is resolved. Back up all data before making any changes.

  1. If possible, test at another network, such as a public access point or hotspot created by a mobile phone. Some Wi - Fi routers are not fully compatible with Apple devices. More specifically, the security mode for the network, as shown in the network preferences window, should be 2 personal WPA or WPA 2 Enterprise. If the router doesn't support either of these modes, it should be replaced with another.

  2. make sure that the network is on the list of favorites by following these instructions. It is important to read the article, as it is the starting point for further efforts to solve the problem. If you skip any step, the problem cannot be resolved. Make sure that the box marked

  Remember this computer has joined the network

  is checked.

  3 follow the instructions in this article to support.

  4. reset the PRAM.

  5. take note of all your parameters of connection Wi - Fi in the network preferences pane, then remove the connection in the connection list and re-create it with the same settings. This by clicking on the icon of the lowest sign from the list of connection, select Wi - Fi as the interface in the form that opens. Select join the other network in the network name menu, then select your network. Enter the password when you are prompted, and then save it in the keychain.

  6. in the menu location at the top of the network preferences window, select Edit locations. A sheet will fall. Click on the plus sign to create a new location. Give it the name of your choice. In the new location, set up the Wi - Fi service with the same settings that you used before. Click on apply and test.

  7. run the Keychain Access application. Find and remove all the network password AirPort elements that refer to the network. Make a note of the password first.

  8 turn off the Bluetoothand the test.

  9. reset the system management controller.

  10. This step should not be necessary, but he has been advised by the Apple Support in some cases, apparently as a solution for a bug. Open the energy saving pane in system preferences. If necessary, click the lock icon in the lower left corner to unlock the settings. When prompted, enter your administrator login password.

  Select the Power Adapter tab and uncheck the boxes marked

  Continued access to the Wi - Fi network

  and

  Enable the NAP...

  If it is present. Then, if the computer is a MacBook, select the stack tab and uncheck the box

  Enable the NAP...

  11. reinstall OS X.