Equium L10-200 - unable to connect to the WLan router

Similar Questions

• Satellite A110-195 unable to connect to the WLan router

  Hello

  I have a wifi router and I have connected my laptop and it worked wery well but on low there is I could not conect to router but woudn't ip address pop up. Internet access was not.
  I am connected to the same router another device and it worked...

  Hello

  Believe me, there is no general solution, you must check all the settings of your operating system

  First of all that I recommend to check the parameters of the TCP/IP protocol if everything is settled automatically on.
  Then check if you are using encryption parameters right as standard (WEP, WPA, WPA2) encryption and the encryption key.

  It s also advised to reinstall or update the Wlan card driver

  If you used the windows own WLan configuration, I would recommend testing as Atheros Client utility or Intel ProSet Wlan client configuration utility. But it depends on the WLan card what client WLan configuration utility can be used

  concerning

• Equium L10-142 - unable to connect to the Internet

  Laptop does not connect to the internet. Have tried 3 ways:

  (i) WIFI - WIFI is clicked. Laptop also can't see other my neighbours networks (my network is OK because may fix another pc WIFI-where this post on the forum!).
  (ii) by network cable - can sometimes become to attach to the wired network (although couldn't this morning) but it will bring up all of the Web pages.
  (iii) external wired modem broadband provided by the ISP. This will not work either. It will recognize the modem, but doesn't bring to the top of the Web pages when I go into Internet Explorer.

  Also cannot access Belkin Modem/Router to administer, even by simply putting in the IP address in the bar using everything above Internet address.
  Laptop running Windows XP with SP2. Have not done everything I can think of to wear this. Laptop works very well to recover documents Word etc and make a backup.

  Help please! Thank you.

  Hello

  Have you updated the WLAN and LAN driver on your laptop? Check the Toshiba site for an update:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  In addition, you should check the TCP/IP for LAN and WLAN settings. If your router supports DHCP, you must set this in the TCP/IP settings.

  You should try to update the firmware of the router you can find on the site of the factory.
  If you go to the menu of the router, you see if the router has an internet connection to the ISP?

  Good bye

• Unable to connect to the WLAN router satellite P300

  Hello everyone,

  I hope you can help me with my problem.

  I bought a Satellite P300. Now, I'll have some connection problems to my fritzboxfonwlan over a wlan network.

  When I connect my laptop via a cable, all right. Only with wlan i´m problems.
  My router ssid is displayed correctly. I can also type the key. But then the router is not to be found.

  I use as wpa2 encryption.
  I think that Vista has problems with it. Vista has also the most recent updates and my wireless (intel agn5100) card.
  I tried all the three drivers on the side of toshiba. I Don t know what I can do next.

  If you have any ideas, I'll be happy to hear it.

  Hello

  Have you checked if the address Mac filtering settings can affect the WLan functionality?
  If the MAC address filtering enabled your WLan card mac address has been inserted, then your laptop wouldn't connect.

  Also I recommend you check the settings of the WLan card TCP/IP.
  In the TCP/IP properties, you must set options for automatically

  PS: have you checked whether your P300 is the latest BIOS?

• Qosmio X 300-13 G - unable to connect to the WLan router using Project N

  Hello
  I purchased a Qosmio X 300-13 g (the only one available in Portugal :/) and I tried to connect it to a network wirelles N, but I always get an error message):
  Windows could not connect because the defenitions of the router are different from your...

  Well you know why? I tried with several routers, and it is always the same...

  TKS

  Concerning

  Is your WLan router supports 802.11 N draft standard?

  Did you choose N draft standard on your WLan router?

• Satellite Pro 6100 - unable to connect to the WLAN router

  Hello

  I brought a 2nd hand Satellite Pro, model version SP6100 (PS610E-029ZV-EN), P4 1.7 Ghz, 512 MB, 30 GB, with Windows 2000 Pro loaded.

  I can't connect to my wireless router. The switch is in the correct position.

  I want to change to XP using the key provided with the new laptop (dual OS) however I can't reformat using a XP disc at the start up or if I use the recovery cd (start with holding C and let go when he works up) it starts but displays 'specification drive not valid' three times and charges Win2000.

  Can someone advise how (or if!) Can I reformat I want?

  Any help will be greatly appreciated.
  See you soon.

  Are you sure that the wireless network adapter has been installed in the laptop?
  Check in Device Manager

  On some series WLan is optional. This means that the WLan card is not installed, but it is possible to install an and, consequently, the laptop contains the WLan switch.

• Satellite P200 - unable to connect to the WLAN router

  I have a Satellite P200 and that you have upgraded from Vista to Windows 7.

  The wireless is working and to see available networks, but trying to connect it does not ask the WEP key, it just says: he has a connection problem and (possibly) says that it cannot connect.

  Someone at - it clues on this?

  Thank you.

  Hello!

  It's really strange Mavourneen. I also have Windows 7 on my Toshiba laptop, but I put t have problems to connect to my router WLAN. Everything works fine on it.

  Can I ask you if you tried to update the driver WLAN? You can download the latest version here:
  http://APS2.toshiba-tro.de/WLAN/

  Have you tried to update the BIOS?

• Satellite L500D - unable to connect to the WLAN router

  Hey all,.

  Hoping that someone here will be more help. For some reason, my laptop won't connect to a wireless network today and it was working fine yesterday.
  When I troubleshoot I get: there might be a problem with the wireless network connection card

  I called belkin and the Lady reset our wireless under a new name which we I = didn t need that my roommate who has vista had no problems with his internet. When I connect the cable through my laptop, I have internet

  Now that I see there no button on my phone to activate the wireless it connected always automatically and the led is on.

  Hi Ren,

  In the wireless issues forum, you can find hundreds of discussions on different WLAN problems.
  Did you check that?
  I think that you will find your answer.

  According to your assignment on resets the router I think that it s properly configured. Check the router security options if the SSID is visible and then encryption and password. Also, make sure that the MAC address filtering is not enabled.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• Equium M50 connect to the WLan router only when security is disabled

  MY Equium M50 will connect to my ROUTER BELKIN g only MIMO when security is disabled.

  What is the reason for this please?

  Blonde bimbo!

  Hello

  Did you mean WiFi encryption that blocks the entrance to the local wireless network?
  I suppose that you have set the encryption (WPA, WEP, etc...) on your router WLan but didn't configure the wireless network adapter.

  Well, in my opinion, you should check out what WLan encryption makes the card holder and then choose it on the WLan router. The encryption key must be set to the router and the laptop!

• Unable to connect with the modem router e2500

  I have an old Speedstream 5100 modem hooked to my router e2500. Everything works well except if for any reason any my modem disconnects from the ISP I can not log in via the route to reconnect it. I need to connect a cable modem to computer direct run connect script then modem plug in router all is well again.

  Any ideas why the connection to the modem router is blocked?

  Thnaks,

  Al

  al_mathews wrote:

  My Speedstream has only an Ethernet connection so I did not know that he resembled a router for the local network. I changed the mode of bridge on the PPoE configuration on e2500 / Speedstream and reconnected to the ISP on the e2500 configuration screen. Who can solve the problem of reconnecting from now, it is run on the e2500.

  One thing I see now is since I left the modem IP set to 192.168.0.X can't do it all through the e2500. Is it because my DHCP in e2500 is configured with 192.168.1.X range IP modem is not covered in my network? If I directly connect Speedstream and place you IP 192.168.1.X will become visible on LAN?

  You are unable to access the modem even if you have a PPPoE connection. For PPPoE the E2500 will not need an IP address from the modem so it does not have DHCP on WAN port and so we never see. When you try to access the address of 192.168.0. * the E2500 it will route through the tunnel PPP to the ISP.

  If you connect your computer directly to the SpeedStream it should automatically get a DHCP address (assuming that the computer is still ongoing on the DHCP protocol and not with a static IP address and the SpeedStream does not automatically neutralize the DHCP server in Bridge mode). If you have configured a static IP address on the computer, you must change the IP address to an address of 192.168.0. *.

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• Satellite L40 - 14N does not connect to the WLan router

  Bought two portable Satellite L40 - 14N as Christmas gifts and one of them does not connect to the wireless router.
  Is the error that says "error message unknown" try please login again.

  The wireless network appears in the list of networks available with a strong signal. Notepad attempts to connect but the error 'wireless link failed for an unknown reason. " Made a comparison with the other laptop that works very well and the configurations appear to be identical!

  Tried it on wireless network from a friend with the same result. All suggestions, am pulling out my hair at this point.

  Seems to be a Vista issue.

  I found this article Ms knowledge base:
  http://support.Microsoft.com/kb/928233/en-us

  You need to add a value in the Windows registry.

  1. Click Start, type regedit in the search box, and then click regedit
  list programs.

  2. Locate and then click the following registry subkey:
  HKEY_LOCAL_MACHINE es\Tcpip\Parameters\Interfaces\ {GUID}
  This registry path, click the (GUID) subkey that corresponds to the
  Network adapter that is connected to the network.

  3. on the Edit menu, point to new, and then click DWORD (32-bit) value.

  4 new value #1, enter DhcpConnEnableBcastFlagToggle, then
  Press ENTER.

  5. right click on DhcpConnEnableBcastFlagToggle, then click on modify.

  6. in the value data box, type 1 and then click OK.

  7. close the registry editor.

  concerning

• Equium A200: Unable to connect to the Wlan - no IP address of the router

  Dear readers

  I have a laptop Equium A200 Toshiba.
  I TI a year, a little more of it and it did work under Vista perfectly, no problem.

  First of a sudded 4 weeks ago my wife told me that she can no longer connect to the internet.
  I thought that it was something less serious, until I couldn't solve the problem.

  The laptop is not receiving an IP address wireless or cable modem.
  I type cmd and I get an IP starting with 169 in wireless and wireed cases.
  I also tried to reset the NETWORK card, but it does not work.

  It's frustrating seriously because we don't change anything on the other machine, then let updates automatically, this is obviously some update that triggered connect to stop the local distribution of load and internet access now it shows only local access.

  Appreciate any help out there on root causes.
  So far not much dad worked. R/Paulcou

  Hello

  In your case, I would first check the settings of the router.
  I put t know what settings of your router is compatible, but you should go thought the simple options (such as when the first router configuration) and should check if everything is set correctly.

  In addition, you should check the settings of WLan connection. In the properties of WLan connection, you would find the TCP/IP protocol. Check the properties of the TCP/IP Protocol and set all parameters (IP address, getaway, etc.) to get automatically.

  If all of these settings are set correctly, then start the console (CMD) and use the command:
  ipconfig / renew

  This should refresh the IP address and in most cases, it helps.

  Last but not least, you should check if you can update the WLan driver!

• Satellite A500 - 03P: unable to connect to the WLan using Win 7 + event message

  Hi all

  I recently bought the Satellite A500 with the offer included Windows7 while he was available late October 09.

  So I had the Toshibe DVD for the upgrade and followed the steps and Visa home premium upgrade to Windows 7. Now I have two questions.

  (1) I get a system event Notification after start, talk to me about the system event log. The full message is below.

  Unable to connect to a windows service
  Windows could not connect to the System Event Notification service. This problem prevents limited users to logon to the system. As an administrator, you can view the system event log to see why the service failed

  (2) I was able to use this laptop for the internet before the upgrade, both via a USB wireless drive as well to the office via a DSL modem.
  Now I can't access the internet after the upgarde of Windows 7!

  For example the Optus dial-up box pop up appears commandeLorsque I click on 'connect', it does not connect.

  Can anyone help please?

  Thank you
  C I

  Hey Buddy,

  (1) did you check the Configuration of the Service for this service? The Boot System Event Notification Service type must always be set to automatic. This service is absolutely necessary for Windows and shouldn't t be disabled or set to manual startup type.
  Check it!

  (2) to be honest I never heard on the internet BEFORE, but normally, it should also be possible to access the Internet with Windows 7.
  Make sure that the WLAN or LAN card is installed properly and check the TCP/IP settings. If you are missing some driver you can get on the page of Toshiba.