error material-05

Similar Questions

• Stop error material unknown c0000415 Help!

  I need help my thinkpad r40 gives me the blue screen of death all that I've done is ibm recovery and reformatted the hard drive, it starts in the large windows installed drivers then automatically restarted when he went in windows it is sitting there and then gives me the blue screen and the error code which is c0000415 please help.

  Welcome to the forum!

  You have an ATI graphics card? Your problem could be related to video drivers that you have installed on your R40. Read this page for more details.

  Thank you

• situation error material vSphere

  Hai

  cant see hardware condition in the vsphere host for 1 only host remaining hosts are very good

  pls be screenshots

  Thank yoy

  Vandenplas

  Remove and re-add the host to vCenter - that will sort them.

  Dan

• Video hardware error, occurring over and over again.

  I'm been a problem with the error material video and bluescreens (doesn't show bluescreen, display just shuts off and I have to force close it down) on my laptop Fujitsu SH560 running with Nvidia Geforce 310 M (support drivers for computer laptop fujitsu last was 309,8).

  I used to have face this problem also, windows update installed a newer version (which is not compatible) but after fixed 309,8 reinstalling several times. However this keeps happening right now even with the correct driver and even after a clean and all installation version. Need some help here?

  Hello

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the question and your efforts to solve.

  This problem may occur because of the corrupt RAM or incompatible drivers.

  I suggest you uninstall and reinstall a previous version of the display driver and check.

  To uninstall the driver, please follow these steps:

  a. press Windows + R keys, type devmgmt.msc in the run window and press ENTER.

  b. Click to enlarge graphic cards, right-click on the map and click Uninstall.

  c. restart the computer.

  Now, reinstall a previous version of the driver to display this link:
  http://www.Fujitsu.com/downloads/COMP/fpcap/Drivers/Driver/VideoN/Nvidia11/v259.04_W7-64/VideoN_NvidiaN11_v259.04_W7-64.exe

  Please also run 'Windows memory diagnostic tool' to correct any error in memory (RAM).
  Refer to this article:
  Diagnosing memory problems on your computer
  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-memory-problems-on-your-computer

  It may take several minutes for the tool finished check the memory of your computer. Once the test is completed, Windows will restart automatically. If the tool detects errors, contact your computer manufacturer for more information on setting, because the errors indicate memory usually only a problem with the memory chips in your computer or other hardware problem.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Install W2K on Tecra 8100

  Hi all

  I am trying to install W2K on a Tecra 8100, but I think I'm doing something wrong, because it keeps failing.

  If I just insert the CD it starts to start a load several files at a time when the Setup starts Windows 2000 (present at the bottom of the screen) and the installation crashes with a blue screen and the c0000221 error material unknown error \systemRoot\System32\ntdll.dll
  I read that, during installation, you will need to press F5 (in the screen where you can load a SCSI or raid driver) and then choose Advanced Configuration and Power Interface (ACPI) PC, but after doing this I get the same error.
  I have no additional material attached, it's original configuration.

  Any thoughts on how to solve this problem and get W2K on my laptop?

  Hello

  I think that this question has nothing to do with the Advanced Configuration and Power Interface (ACPI) or similar.

  I read about the error systemRoot\System32\ntdll.dll message, and there is no particular reason for this error.
  Sometimes some service packs missing cause this problem and sometimes hardware malfunction (RAM or HARD drive) could be responsible for a BSOD.

  You are able to install Win XP?

• "ITS creation failed" problem for IPSec VPN

  An ASA 5100 is used to provide VPN access for my business. The configuration was made by a permeable man who has been missing for some time, and the configuration used to be OK until this morning. This morning, some users reported that their VPN would have fallen once got connected. I checked the ASA and ASDM, I see every time when user deletes, it IPSec tunnel is always action. Furthermore, I faked the problem and got the newspaper of errors such as:

  1 11:14:45.898 12/06/07 Sev = WARNING/3 IKE/0xE3000065 could not find an IKE SA for 10.2.1.8. Abandoned KEY_REQ.

  2 11:14:45.898 12/06/07 Sev = WARNING/2 IKE/0xE3000099 could not open the P2 generate a new key: error detected(Initiate:176)

  3 11:14:45.898 12/06/07 Sev = WARNING/2 IKE/0xE3000099 cannot open the QM (IKE_MAIN:458)

  On the side of the AS I did "debug crypto isakmp" and 'debug crypto ipsec' and I got the following errors:

  iscoasa # ERROR IPSEC: expiration of the timer of the asynchronous operation, SPI: 0x114CA5B6, user: roeladmin, peer: 202.x.x.70, time: 2 seconds, ctm_ipsec_create_sa:856

  IPSEC ERROR: Material outside ITS create command failed, SPI: 0x114CA5B6, error code: 0 x 17

  IPSEC ERROR: Asynchronous Operation timeout expired, SPI: 0x61BE2022, user: roeladmin, peer: 202.x.x.70, time: 2 seconds, ctm_ipsec_create_sa:856

  IPSEC ERROR: Cannot add a user auth, SPI input: 0x61BE2022, user: roeladmin, peer: 202.172.62.70

  IPSEC ERROR: Cannot create an inbound SA SPI: 0x61BE2022 document

  IPSEC ERROR: Unable to complete the command of IKE UPDATE

  12 June at 14:25:13 [IKEv1]: Group = LANWORKS, Username = roeladmin, IP = 202.172.62.70, error QM WSF (P2 struct & 0 x 4699058, mess id 0xf37ec6f4).

  12 June at 14:25:13 [IKEv1]: Group = LANWORKS, Username = roeladmin, IP = 202.172.62.70, peer table correlator Removing failed, no match!

  IPSEC ERROR: Material Inbound ITS create command failed, SPI: 0x61BE2022, error code: 0 x 17

  It shows that ITS creation has failed. But I can't find the problem with the configuration. Can someone help me on this? Thank you

  Outgoing material ITS create command failed, SPI: 0x114CA5B6, error code: 0 x 17

  It is a hardware problem, reset the firewall and it will work, I saw 4 times in different ASAs

  Please hate the post if help.

• How can I replace a ntdll.dll in Windows 7 Home Basic

  I have Dell Inspiron 15R installed with Windows 7 Home Basic with SP1, ntdll.dll has become corrupt. But if I check with sfc/scannow, it shows no problem. I tried to replace the ntdll.dll from another system of windows 7 by the boot of Ubuntu, but the system crashed, therefore, I have to replace the old file back.

  Therefore, please suggest how to replace the ntdll.dll corrupt without installing the OS from scratch.

  @ FantaSS

  =============================================================================
  There are different ways that ntdll.dll errors can appear on your computer.
  Ntdll.dll errors can be caused by a number of different things that translate into many different error messages, but some of the more common ones are listed below:

  • "STOP: 0xC0000221 unknown hard error C:\Winnt\System32\Ntdll.dll.
  • "STOP: C0000221 error material unknown \SystemRoot\System32\ntdll.dll.
  • "AppName: [NAME OF PROGRAM] ModName: ntdll.dll.
  • "[PROGRAM NAME] has caused an error in module NTDLL. DLL at [FULL ADDRESS]"
  • "Crash caused in ntdll.dll!
  • "NTDLL. DLL error! »
  • «Unhandled exception address [ANY] (NTDLL.» (DLL).

  Ntdll.dll error messages can appear before or after a program is used, while a program is ongoing, when Windows is started or stopped, or even during a Windows installation.

  Cause of Ntdll.dll errors
  The causes of ntdll.dll error messages can vary considerably. However, most of the ntdll.dll errors result from a corrupted or damaged file ntdll.dll version itself, corrupt hardware drivers, or issues between Windows and other programs.
  Ntdll.dll errors can sometimes mean that a piece of hardware in your computer is faulty, but this is rare.

  How to fix Ntdll.dll errors:

  1. Restart your computer: the ntdll.dll error you receive may be due to a one-time, temporary issue and a simple reboot may solve the problem completely.
  2. Reinstall the program if the ntdll.dll error only when you use a program.

     If the software updates or service packs available, install them too. Software programmers may have identified an issue with the program that caused the ntdll.dll error and then issues a patch.

  Note: Software of third party that have been installed on your computer are almost always the cause of errors in ntdll.dll. The rest of these troubleshooting steps to solve the problems of ntdll.dll that rarely.

• Check the windows service pack level you use, and consult the Microsoft support site to see if there is a service available for installing the newest pack. Some of the issues that caused the ntdll.dll errors have been corrected in these service packs from Microsoft.
• Disable Add-ons from Internet Explorer selectively: If your ntdll.dll error appears when you start, run or close Internet Explorer, an add-on may be causing the problem. Deactivation of each module, one by one, will determine what add-on is the culprit (if any).

  Note: As a solution, assuming that the ntdll.dll error is really Internet Explorer related, install and use a competing browser like Firefox.

• Rename the NLSPATH system variable: If your Windows system does not have this environment variable, skip this step.

  Note: It is a step of troubleshooting for this issue only. Don't forget to put this way its original name, if this does not solve the problem of ntdll.dll.

• Turn off the Data Execution Prevention for Explorer.exe: as in the previous step, this is for troubleshooting only the question of ntdll.dll. If this does not resolve the problem, return the Data Execution Prevention settings to their previous settings.
• Update the drivers for any hardware in your computer where the updated drivers are available. Out-of-date drivers sometimes cause errors of ntdll.dll.
• Test your memory for damage: If you receive messages from ntdll.dll, one possible cause could be a memory module in your system. Test your memory will be either identify a problem or clear your RAM from liability.

  Replace your memory in the event of failure of your tests.

• Ntdll.dll errors may occur if you have an Iomega Zip drive on the same IDE cable as the hard drive inside your computer. If so, move the Zip drive to a dedicated IDE controller.
• Replace the IDE cable connect the hard drive to the motherboard. If this cable is damaged or defective, one of the symptoms could be the ntdll.dll error you see.
• Repair your Windows installation: If the resettlement of individual software fail to solve the problem, a Windows repair installation overwrites the ntdll.dll file.
• Perform a new installation of Windows: a new installation will completely remove Windows from your PC and reinstall from scratch. I do not recommend this option unless you have exhausted all the previous troubleshooting ideas and you are comfortable that the ntdll.dll error is not caused by a single program (step 2).

  Note: If a single program or plugin causes the ntdll.dll, reinstalling Windows and then reinstall all the software even can lead you right to the same ntdll.dll error.

• Although extremely rare, if everything else failed, including the facility clean at the last step, you might be dealing with a hardware problem with your hard drive.

  If so, replace the hard disk and then perform a new installation of Windows.

=============================================================================

I hope you this help.
BillyRazOr

• ESXi 5.1.0.799733 GROUP

  Hello

  There's an ESXi server installation was performed for more than three months, suddenly appeared the week last after the error screen, which is caused by a hardware problem or software?

  

  Looks like an error material, but hard to tell. Mind tell us what kind of hardware you are using and if it's on the HCL?

  Also make sure that the firmware/BIOS is up to date and you may want to run memtest overnight to eliminate the flaws of memory.

• MPE problem with gtx 580

  Hi, I have a weird problem with my first. I the maximum permissible error material value, but it doesn't seem to be something, and the gpu left unused too.

  I don't think its something to do with the parties, but my pc is:
  I7 970 4.3 GHz

  12 GB of ddr3 memory

  GTX 580 3 GB

  128ssd 500mbps r/w with enough space

  I can't understand why its been nothing. can anyone help? Thank you.

  When you use two monitors Windows Aero can perform playback in real time. I think that there is a message or a thread about tweaking your system to use the PP but I do not know the url of a link. Could someone post the link for you.

• Errors/problems with my brand-new Equium A200 15I (including video material)

  Hello

  I am treated to a new computer laptop last Saturday and only had for about 3 and a half days so far but I noticed a few things that I wasn't sure were errors/defects or if it was simply because its news, like the fact that sometimes I type with the keyboard and some letters do not appear on the screen , I think it's probably more to do with me not type or support pretty strongly on the keys rather than anything else, his is not so much now... the touchpad becomes a bit sticky too and he thinks I want to scroll up and down when I move the cursor does not scroll sometimes but I managed to make it work I think that most laptops have glitches like that and no doubt I could help fix it in calibrating the pad (?) touch I did have time to consider the issue and yet if... There are a few other things well and more disturbing than this morning I got an error of video material, so now im a little just worried or suspicious that it may be a real fault with him and would like to know if it is the case, if its something I can fix eventually (im no expert especially with the material, but I can always try to download and installation of updates / corrections and this kind of thing so she could solve the problems).

  The main thing that concerns me more, is that this morning a message suddenly come to the screen, warning me that there was an error in video material, last night, I clicked on a button, I think for load more information. and I took this perforated cap of it: -.

  http://img528.imageshack.us/img528/724/errorscreencapcw1.jpg

  I thought it may be useful to view the actual complete message rather try everything and paste the info., ok to be honest I've not noticed it allow you to copy to the Clipboard, but good (oops lol).

  I know there is a topic on a similar error, but I didn't want end-to-end on this discussion because I assume that it should be for this mistake of people who will be discussed, mine may be slightly different, I don't know... I followed the instructions given in this discussion and I checked the Device Manager and no material defects are appearing, btw it is said in the Manager of peripheral devices, graphics cards, it's a Mobile Intel 945 GM Express Chipset Family, I'm sure that all laptops A200 15I have the same card, but I thought I would just make it clear that. Incase that wasn't the right thing to check I also checked under "Audio, video and game controllers" (as the error says it was a video hardware error) where it lists the only as being "Realtek High Definition" Audio and I checked the properties, both under properties it says that the device works properly, without signs of defects...

  The thing is, I had read somewhere online that there is a problem with the graphics or video cards. I had read that they can be glitchy and sometimes break after a year. I also asked my father about it and we looked at it as a graphics card Intel that came with this laptop, which it is, and we counted that the Intel chips is as reliable as any other brand really... so I don't think there should be a problem, well that is there I have until September next for repair prior to the expiration of the warranty!

  What surprises or sort of worry, however, is that the error message was only introduced to me this morning. It dates from error, as having occurred at 19:53. I use it at night last, and infact, I went to take a shower and I put the laptop down before you go take a shower at around 19:35, I assumed that its ok just close the lid and it would automatically go into hibernate mode or something similar (?) im wondering if that had something to do with it as I 19:53 would have been about when I came back and lifted the lid/screen again to use the laptop again... I can only assume, given the time, he cites, is what caused the failure?

  It gives me the option to "update driver software" and "hardware change analysis" in the Device Manager, can I run both, or one of those who maybe? is this a common problem? should I worry at all etc...

  Any help is very appreciated, if more info. Please let me know and ill clarify what I can. Also in terms of whats installed, I have quite a few programs, for graphics, I have an old version of Paint Shop Pro, which I installed it yesterday morning, it seems to install fine, it is Jasc Paint Shop Pro 7, I have also some programs of converter (for files vid, 3GP and other things), scan antivirus AVG, Spybot Search & Destory DBPowerAmp, FTP Commander, Quicktime and Real Player, pretty basic stuff like that, nothing, just my old photos and vid files I transferred from my old laptop XP to it, in my documents... I don't have all the Senior Games motorized or complicated or anything else like that installed. Also at that time, indicates the video hardware error message, everything that was in progress when I got the cover down (or before putting the lid down) would have been Windows Live Messenger (although I'm pretty sure that I registered before putting the lid down) and an IE window , im pretty sure that's it, I was not working on anything just check the ' net...

  There are other things I noticed as I thought that maybe I should mention (?), something I've noticed he's doing is the screen goes blank and then back very quickly, a lot. I already asked about it a day or so there at that time, I realized he was only doing that before loading the "Windows needs your permission to continue" window/message, who apparently its supposed to do and something to with the computer to switch to display the normal desktop to the secure desktop, I kind of understand lol.
  So I think that's not something to worry about but I noticed during the lastday, that the screen seems to do it more, goes blank then back again, even if the authorization message does not appear.

  For example, this morning, when I first put on and am went to check out my home page, I clicked on a link at the bottom of the page or anywhere where to load another page into the site and display deleted for a while before coming back a second later with the requested page. Is this normal too? or an associated Vista glitch, or is it possible that there may be a small problem with the monitor? Incase of im guessing it can be more than one thing in Vista, but I thought I would ask here, I decided to not pay for any extra insurance/warranty extension because I am very careful with my items and take care of them and so I'm being careful to try to spot defects early, while they may be repairable under the basic warranty and what-not...

  Another thing I noticed is that start with, when I pressed on and kept the 'FN' key, a variety of icons, black and white appeared on the screen that told me what F button (s) to use to make certain adjustments, there still is that when I try right now, but at other times, it does not show icons , no matter how long I hold down the "fn". That didn't matter because I can tell by the symbols on the keyboard press what buttons but its just inconsistent, is there a reason why sometimes the row of icons on the screen will appear when I press and hold the "FN" key and other times it doesn't show at all?

  Also sometimes if I move the slider to the right to the top of the screen, these icons loading as they always seem to be located at the top of the screen, but sometimes it's a problem, if im trying to click on something else and one of these icons rises instead... I'm sure that you can disable this option in sort , but I'd be worried that the icons do not always show when I press and hold the right Button (?) just try to be careful!

  I think that this post is long enough and I don't see what else I could possibly add to help, so I'll leave this here. I don't want to sound too paranoid, but thought it is better to talk about this kind of things incase someone recognizes these defects/errors and can recommend a way fast to resolve potential problems before they can develop into what whether it is worse... Thank you very much in advance for any help on any of these issues!

  (mods let me know if im wrong to include so many things in a subject, I fact kind of this quickly and I apologize if im breaking any rules, I don't want to, if possible please break this into a few different themes or I can do it, although ill be at work frm 2-21:00 today so maybe not back and able to check here until Thursday morning (October 4))

  Hey Isla

  Your message is really very, very long. I think it's too long to read twice ;) s

  . Regarding your questions on this laptop well. Looks like you have installed many applications and 3 third party programs. In such cases, it s not easy to say if these problems are software or hardware related. But I guess that its software.

  I checked your screenshot pic, but I've never seen this error message. But it looks like something wrong with the graphics driver. The message says something, live events of kernel
  The core services are required by other parts of the operating system as for example graphics card driver.

  In this case I recommend updating the graphics driver. According to you, this message an Intel GPU. So you can see the Intel page for the driver for the graphics chip compatible.

  With regard to the key issue of the FN;
  The Toshiba FlashCard utility controls the key features of the FN. I read in this forum that this application does not smoothly run and in some cases it causes some issues. The new update should solve the problems. You should check the Toshiba driver page. The utility of FlashCard is a part of the Toshiba value added package.

  So finally a tip more:
  You should always check the updates of Vista on the Microsoft page. This operating system is not perfect and Microsoft releases hotfixes and patches very often

  I hope that it would help a little.

  If necessary just ask for more information :)

  Concerning

• What material test error 4MEM/62/40000000: average 0x831efd18?

  I have an Intel Core i5 to 2.3 GHz early 2011 MacBook Pro.  I just upgraded my 4 GB of RAM on a single chip of 8 GB of RAM DDR3 PC3-12800 PNY (3 days ago).  The system has been working very well, without boot errors, not gel, just normal race.  I ran the test material as a preemptive measure to be sure everything was cool, and the above error is reported.  I don't know what this means, and I don't know if it's something I need to worry.  He could have made with my old 'stock' RAM, but I've never run the hardware test with 4 GB of RAM installed.  As I said, everything seems fine, only just a little concerned with the error.

  I will say that since the addition of the unique chip I read some places that it is recommended that you run 2 identical boards, so I have a second PNY 8 GB RAM to come in the mail, and pop that in too.  I really need the 16 GB but I want to place as little stress on the system as possible and the two fill ports seems to be recommended.

  Thank you for any help or advice you can give to this error report.

  This error code indicates a problem with RAM.  Remove the module, clean the contacts and replace it ensuring that it is properly installed.

  Also, try adding one of the older modules and rerun the AHT.

  Also with just the old modules only and test with the AHT.

  Note that an error free AHT is inconclusive.

  Ciao.

• CAN grasp the material master Timebase rate returns an error with new hardware OR XNET

  Hi all

  I have a project that communicates on a CAN bus. It has always worked well with a PCI-CAN/2 card, but when I tried to use it in combination with an NI PCI-8512 (NOR-XNET) newly purchased card, it returns the following error:

  "1074388560 error has occurred CAN set material master Timebase Rate.vi

  NI-CAN: (Hex0xBFF621B0) the specified feature has a drawing or model under the NI_CAN which can be made compatible with the hardware, NI - XNET CAN. »

  Yes, I have installed the NOR-XNET for NI-CAN compatibility library.

  The error occurs during the initialization of the RTSI connections for synchronization, that VI is attached.

  I guess that this code is based on an example found in LabView.

  When I remove the BOX: block Set (material master time base rate) property, there is no error and the rest of the application seems to work very well.

  Can someone explain what is / was some timebase setting the internal clock of 10 MHz before connecting a RTSI line for her?

  Are there side effects caused by the elimination of this step?

  Should I still include if I run the application in combination with the old card PCI-CAN/2?

  Thanks in advance.

  Hello Pianne,

  Based on our discussion in class, it seems indeed as part of your existing code is written in a very specific way which is not entirely compatible with the XNET approach.

  Indeed, it would be useful to have 2 separate versions of this init VI (and other CAN-code) of your code and allow you to decide which one to run your top-level application, depending on the setting used.
  A HAL as approach could still be used in this case.

• Error while trying to initialize the session of material

  I get an error when you try to initialize a session of material so that I can control my cards PXI-4110.  I've attached a screenshot of the code that I am running with the error message that appears.  I used this code before on a separate system yet identical and received no error.  I'm trying to deploy this code on a real-time system running Pharlap or whatever it's called now.  The real-time system is hung across a MXI map in a PXI chassis containing power cards.  I'm under LabVIEW 2012.

  In fact, I just got on the phone with a representative OR today, and he asked me to set my target to the local host rather than my machine in real time and for some reason that seems to have solved the problem.  Even the rep was not really sure why that would fix it, but he did.  Thanks a lot for your great answers.

• Material up to date Assistant, MTP device an error occurred during the installation of the device

  I have a problem installing the driver for my mp3 player. I get this message after I try and install "" there was a problem installing this device: MTP device, is an error occurred during the installation of the device the specified service does not exist as an installed service. "" Even if I uninstall and re install the driver, I still get the same message. What could be the cause of this error message?

  My operating system is Windows XP home

  Original title: update Hardwre Assistant

  Hi D.L.B1,

  • What is the brand and the model number of the MP3 player?
  • Other USB devices are connected to the computer works well?

  You try to manually add the MP3 player to the computer and check if it can help solve you the problem and if the MP3 player is detected.

  You can access the link below and follow the steps in the article to manually add the material to the computer.  When adding the verification of the material if it appears two devices one by one for device MTP and other USB Mass Storage Device. If it shows both, select the USB mass storage device from the list and try to install it and check if that helps.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/app_start_hardware_wizard.mspx?mfr=true

  If the problem persists and you cannot install the MP3 player, you can contact the manufacturer of MP3 and check if you need to make changes to install it and if they have the latest drivers to install.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• DVD player does not appear error - the driver may be corrupted or missing. Code 39, fix the driver installation fails, virtual drives don't work - same results if the material under tension

  Original title: drive does not appear, difficulty he pilot installation fails, virtual drives don't work - same results if the material under tension

  A few weeks ago, as my two DVD players (the two Samsung Lightscribe SH-S223Q of) disappeared after a repair installed, I did for the other problems (not sure if it was directly after installation because I don't notice it right away, but it was no doubt). In Device Manager, it gives the message:

  "Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39) »

  I tried the Microsoft Fix It tool (Mats_Run.dvd.exe) that detects the problem and says "Install device driver" in a popup, but then he says "software device driver failed to installed. At the end it says under the issue, the "CD/DVD drive is not detected" and the status of Fix 'not set '. Note that, when I boot from another hard drive (with Vista 64 on it installed from the same DVD, just a new installation) disks appear very well. Also I can boot from the drive as well.

  I can't do a repair installation, since it must initiate Windows, and I can't load the disc. I tried to update my BIOS but that has no effect.

  Recently I actually moved this hard drive to another one, with another brand of hard drive and all the rest. Just like before, if I boot from another hard drive (this one with Windows 7), the drive unit-a Optiarc AD-7230 s - looks and works, and I can also boot from the drive at startup. But since the drive hard as I want to use, the drive does not appear. Fix it, etc. Device Manager gives the same messages as before.

  I tried virtual drives - Daemon Tools Lite and Virtual Clonedrive. When I try to add virtual devices to help, nothing happens. The new drive will be displayed in the Manager of devices, but with the same error Code 39 as the real drive.

  What are my options at this point? How can I get the drive to appear or to fix my copy of Windows?

  I could solve this problem. I started in Ubuntu and deleted the existing cdrom.sys, cdrom.inf etc. files (as in Windows, they were protected and I couldn't delete them), then I copied the files from another installation of Vista I had on another hard drive. After having done that, I updated the drivers in device, disabled/enabled readers and readers management that presented themselves.