error message... "error: no such partition." grub rescue

Similar Questions

• HP DL380 Gen9: HPDL380 Gen9 GRUB! error: no such device: HPEZCD240

  I have to install the operating system in a new Gen9 DL380.

  It has two SATA drives.

  After starting "Inteligent Provisioning", I get the following error message:

  "error: no such device: HPEZCD240.

  No idea how to solve this problem? Is there another way to set up the matrix of discs?

  Thanks in advance, Miguel

  I found the solution in page 10 of the manual http://www.hp.com/ctg/Manual/c04419967.pdf

  I was because I added a GPU, and I plugged the monitor the GPU video output.

  From the Manual:

  Cause all the Gen8 and Gen9 ProLiant servers provide only video F10 on the integrated video card and through the remote console of the ILO. If a GPU is installed in addition to the integrated video card, the software is unable to determine the "right" monitor at boot time, and F10 video redirects to the virtual video of the ILO or the integrated video port.

• VMware converter 5.5 failed with the error failed to partition the disk of destination

  I tried to convert the centos linux server physical to virtual. However, I received an error message at 1% as below,

  Error: Impossible to partition the disk of destination.

  FAILED: an error occurred during conversion: "CalculateGPTPartitionLocations failed!"

  
  

  Conversion of GPT partition is available vcenter converter 5.1 and higher, so the GPT partition on the source server will not be a problem.

  Tried several ways as the storage of data changing but still receive the same error message.

  Anyone encounter this before?

  Hello

  Unfortunately there is a bug with Linux P2V Converter when the destination drive is greater than 2 TB (is not whether TPG, it's size). Sorry for the inconvenience.

  The solution would be to reduce the volumes instead of destination and/or their distributed on multiple disks. Another solution would be to leave unchecked high-volume and clone them manually after the conversion.

  Another misfortune is that these workaround solutions are not possible in your case - the root volume occupies approximately 4.3 TB, and the two 'start-up' and '-' are needed to perform a conversion with the reconfiguration.

  The options I can think of are:

  -make a manual P2V, i.e. to create the destination (with partitions, logical volumes and base) computer created and formatted, clone the data (for example the converter uses tar via ssh) and manually configure the virtual machine. The final step is, fixing/etc/fstab, installation of GRUB and rebuild the initrd image

  -install new and copy data

  -Optionally divides the volume of root on the source machine if possible and then convert it. For example, to add a new drive temporarily and move some data so that all volumes become smaller than 2 TB.

  Kind regards

  Plamen

• Getting error while creating partitation on hard drive

  Getting error while creating partitation on hard drive

  Attached screenshot for warning msg

  You can have up to four primary partitions. Since you already have four of these partitions, you cannot create a fifth partition. You must do this:

  1. Delete a primary partition.
  2. Create an extended partition.
  3. Create logical partitions as you wish within the extended partition.

• Problems installing jDeveloper - launch ERROR: no such file or directory

  Hello, I am trying to install the 64-bit version of jDeveloper Windows 12 (jdev_suite_121200_win64.exe)

  At the beginning of the installation, an error window appears saying:

  Launch ERROR: no such file or directory

  Thanks a lot for any assistance!

  Figured it out.  Solution validation for other credit issue.

  Need to run as administrator by the article below. Windows 7 x 64, just right click on the exe jDeveloper and choose 'run as administrator '. »

• Grub rescue

  I deleted the partition 12.04 linux on my hard drive. Windows partition 8.1 is still there, but after the removal of the linux partition, I rebooted the pc and just a black screen with error->

  error: unknown file system.
  Grub rescue >

  I know that this problem is solved by repairing the window start but I can't do it because I don't see my selection of boot or f2 and f12 option. If the boot drive does not load .i also have disk bootable linux and windows.
  Please help solve this problem.

  Note of the moderator; published subject lines

  Finally found the solution after tring very hard. Its small with different and dangerous, but worked 1000% for those who has the bios bricked or who did not enter the bios and want to recover the bios key like f1, f2, f10, f12 etc.
  Thankx for your support and for your valuable answers.

• G500 does not start Grub Rescue problem

  Just purchased a G500 laptop and installed Win7 and ubuntu.

  Next day morning peripheral gives that ' the unknown filesystem, grub rescue > ' message.

  One key recovery button does not work. Cannot get into the bios, so cannot change the opening via USB boot sequence. Tried the F2, F10, F12, ESC, Del possibilities and with the Fn, but bios combinations shows not itself.

  I tried win7 and ubuntu cd, nothing works.

  What type of camera to buy? Every time that MBR broken, should I send this service?

  I really frustrated, this should have a tag on, "not for linux!

  Finally

  removed the battery, removed the bios battery.

  Press the button for 10 seconds.

  plugged the battery at the back.

  Press F2, F2 just not with Rem and waila here is the bios.

  It shouldn't be this hard.

  Note of the moderator; swear implicit edition rules of the Forum

• ERROR MSG - 1023040 - partition of remote site: need to understand

  Hello

  I currently have a problem with the partitions between the two cubes.

  Architecture:
  database of 80 countries (source)
  1 world database (destination)

  Process:
  -Partitions are dynamically created by maxl scripts:

  -------------------------------------------------------------
  the coil $ 1;
  Change request comment $2 ' * _batch_ *';
  Change the comment to request $4 ' * _batch_ *';
  Modify the application of the system $2 load;
  Modify the application of the system $4 load;
  Change request $2 disable start-up;
  Change request $4 disable start-up;
  Disable application $2 ALTER connects;
  ALTER request $4 disable connects;
  
  / * Create Transparant Partition between countries in the world cube cube * /.
  create or replace the replicated partition $2. $3
  AREA
  "" S_R_N",
  & curr_month,
  & local_currency, "D_EURO."
  @IDESCENDANTS ("P_Produit"),
  @LEVMBRS ("M_Marche", 1), "M_Marche,"
  @IDESCENDANTS ("B_Marque"),
  @IDESCENDANTS ("U_Sourcing"),
  @REMOVE (@DESCENDANTS ("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS ("I_Divers").
  @IDESCENDANTS ("NA_Nature"), PCS '
  for $4.5 $
  AREA
  "" S_R_N",
  & curr_month,
  "D_DEV", "D_EUR."
  @IDESCENDANTS ("P_Produit"),
  @LEVMBRS ("M_MixClient", 0), "M_MixClient,"
  @IDESCENDANTS ("B_Marque"),
  @IDESCENDANTS ("U_Sourcing"),
  @REMOVE (@DESCENDANTS ("I_Masse"), @LIST ("I_55CCOM")), @DESCENDANTS ("I_Divers").
  @IDESCENDANTS ("NA_Nature"), MCX,
  & country_name"
  mapped global (", $ 7, 'D_EURO', 'M_Marche' D_) to (W_$ 6, D_DEV, 'D_EUR', 'M_MixClient')
  ;
  
  update the replicated partition $2. $3 à $4. $5 all data;
  Drop partition replicated $2. $3 to $4.5 $;
  
  Change the application $2 start activate;
  Change the start application enable $4;
  Enable application $2 ALTER connects;
  ALTER request $4 activate connects;
  Change request comment $2 ' * _enable_ *';
  Change the comment to request $4 ' * _enable_ *';
  Change the unloading system $2 application;
  Modify the application of the unloading system $4;
  Spool off;
  Disconnection;
  "exit";
  -------------------------------------------------------

  -Cubes of defragmentation, launch country of replications successively to the cubes world sequentially.
  the order of the country is not the same from one month to another.
  Treatment is started each month.

  
  S ymptoms :
  -Partition fall into the error with the following message is displayed, but not systematically.
  Message:

  MAXL > update replicated partition PGC_ESP. Pgc_esp PGC_MOND. Pgc_mond to all data;
  
  ERROR MSG - 1023040 - remote site [[Wed Nov 29 10:21:03 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error (1023040) remote site msg [[Wed Nov 29 10:21:02 2013] hprx1302 / PGC_ESP / Pgc_esp / PGC_ADMIN / msg of error (1023040) of the remote site [[Wed Nov 29 10:21:01 2013] hprx1302/PGC_MOND/Pgc_mond/PGC_ADMIN/Error (1042012) network error [32]: can not send data]]].

  We note that the error occurs in the following cases:
  -L'errerur occurs generally when the average ratio of clustering is low. (fragmented cube) for cubes source and / or destination
  -How many other replication have been done before: in the remaining replication cube last from 10 to 15.
  -We wrong once on the environment of recipe on the first cube with average ratio of 0.96 but clustering server recipe is much less effective.

  We have noticed that when you perform a defrag cubes source and destination once the obtained error replication of treatment is more grave in error.
  Problem: world of cube of defragmentation take 10 hours.

  We also made the following observation:

  -------------------------------------------------------------------------------------
  OK/INFO - 1051034 - user [PGC_ADMIN] connection.
  Last connection OK/INFO - 1051035 - Friday, November 29, 2013 10:19:46.
  OK/INFO - 1053012 - [Pgc_esp] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053012 - [Pgc_mond] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053012 - [54116855] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053012 - [39843334] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [54116855] object.
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [39843334] object.
  WARNING - 1241137 - [target] - definition of the Partition is not valid: [cell count mismatch: area [1279464568200] for members of the unit [1] by dimension [63 1 2 1 6 26 7 245 1 37955]].
  OK/INFO - 1053012 - [25586652] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053012 - [11329970] object is locked by the user [PGC_ADMIN].
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [25586652] object.
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [11329970] object.
  WARNING - 1241137 - [Source] - definition of the Partition is not valid: [cell count mismatch: area [47895484140] for members of the unit [1] by [63 1 6 7 2173 2 17 1 245] dimension].
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [Pgc_esp] object.
  OK/INFO - 1053013 - unlocked by the user [PGC_ADMIN] [Pgc_mond] object.
  OK/INFO - 1051037 - disconnection of the [PGC_ADMIN] user, active for 0 minutes.
  OK/INFO - 1241124 - Partition replaced.
  -------------------------------------------------------------------------------------

  Following these results, we must understand what is happening.

  We would like to understand why the scores fall errors?

  why we have the "definition of the Partition is not valid" message in the logs when creating the partition?

  
  Kind regards
  Oliv.

  to eq cut may be in the definition of the partition.

  245 members in source and target to 245.

• Error deleting windows partition

  I created a 35 GB windows with bootcamp partition, but realized it wasn't enough for my needs... then decided to delete the bootcamp partition. at the end of the process, appeared an error related to the score and realized that the windows partition was still there, but I can't withdraw via bootcamp... in botcamp is not as if there are partitions.

  PLEASE I NEED HELP. I DON'T HAVE A TIME MACHINE BACKUP. I HAVE SOFTWARE VERY IMPORTANT AND CANNOT FORMAT MY MAC

  SUMMARY: REMOVE THE HD PARTITION. WITHOUT DAMAGING THE OSX AND ARCHIVES

  http://i.imgur.com/z8RnTUL.jpg

  problem solved!

  anyone having the same problem follow these steps:

  Open the "disk utility" click on your HD (usually: Apple SSD media... etc)

  Click on "Partition" select the bootcamp partition on «-»

  then click again on your hard drive and select "repair".

  the final then close disk utility and open your hd will it with the space of origin without partitions!

• error 0xC0000225, recovery partition does not start

  Hello

  I have a HP dv7 with Windows 7 Home premium 64-bit.

  A few months ago, I did a factory restore, the recovery partition start (I have no recovery disks). After that, I thought to divide my C: partition where Windows is installed, and I did it with Windows disk management.

  So my new scores were: C: D: with recovery, OS, E: HP_Tools and g.: the new partition.

  A few days ago the sistem ran very hard, so I thought I do another factory restore from the recovery partition. When I rebooted and you press F11, I got the "0xc0000225 error".

  I have a Windows 7 Home Premium 64-bit bootable drive and I tried Startup Repair tool and other repairs of sistem, checks HDD, but everything seems to be ok.

  I reinstalled the operating system, from the disk bootable on C: (OS starts and works well) and let the other partitions as they were... but it seems that the recovery partition still does not start if I can do a restore from the factory with all the drivers and utilities, as they were at the beginning.

  Any ideas on how I can do?

  Thank you!

  It seemed that it there was not much I could do about this problem. My disk is dynamic, there is no Recovery Manager from the Start Menu, there has not been any creation of HP with HP folder recovery support. I managed somehow to make a repair disk, I tried it but no results, the error kept popping out every time.

  I inserted the Windows 7 disc to try to delete all partitions, including the recovery and HP-tools and do a Windows Installer Cleanup, but the Format, New and Delete buttons are inactive.

  I did some scans disk and memory tests, everything was ok... I started with a disc of Hiren and accesed the HARD drive with a program based on linux and so I managed to delete the partitions.

  After I installed a new copy of Windows 7 to work with my SN and everything was ok. Unfortunately I lost partitions recovery and HP-tools, but at least it works well again.

  Thanks for your all your support.

• disk management errors and lost partitions

  I have reimagee a older laptop that has a 500 GB drive. In the process, I have partitioned the hard drive in three volumes: a drive T: and V: each with 100 GB and C: got balance. A day or two later, I noticed T: and V: mysteriously disappeared. Fortunately, I didn't put anything in them again, there was no loss of data. However, it seems that I have lost access to disk space. Disk management show up with this:

  

  All traces of T: and V: disappeared. The c: volume 226GB poster (including 148GB is free)... which is all what I think after I had partitioned the disk. But then underneath, the entry to disk 0 C: Watch is affected 465 GB... it is unclear where the balance of 35 GB went. If I try to reduce the volume, it presents me with the total available size 476938MB and shrink space 151834 MB. If I try to further reduce 1 MB, it fails with the error "Virtual Disk Manager: the parameter is incorrect."

  Now that I'm in this State, is it possible to recover without start from scratch?

  Use the free Partition Wizard boot CD to shrink C by as much as you like.

  Assistant Creation of partition resize Partition - video help.

  Create and format partitions of data desired logic.

  Create partition Wizard Partition - video help

• Don't get an error "no such interface taken in charge", while accessing the control panel or file

  * Original title: I get no such interface supported no matte what file I click and don't have not re install cd cant wipe f8 or how do short ifx buy new HD? Have 530 dell insperion

  I bought a computer (which group of experts online as you can see) but no matter what file I choose or accessory control pannel etc... get same error no...

  I tried to do a factory restore, but it doesn't let me do that same how can I fix that I don't have the installation cd either?

  Hello

  -Have there been recent changes made on the computer before the show?

   

  Please follow the steps below and check if that helps.

   

  Method 1:

  I suggest you run the troubleshooter of performance on the system and verify.

  Open the troubleshooter of Performance

  http://Windows.Microsoft.com/en-us/Windows7/open-the-performance-Troubleshooter

   

   

  Method 2:

  I suggest that you run SFC (System File Checker) scan on the system and check. Follow the steps in the following article.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3:

  If the problem started recently, I suggest you do a system restore to the previous point and check.

  What is system restore?

  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/system-restore-frequently-asked-questions

  Important: System Restore will return all your files non-system as documents, email, music, etc., to a previous state. These files of types are completely affected by the restoration of the system. If it was your intention with this tool to recover a deleted file to non-system, try using a file instead of system restore recovery program.

   

  Method 4: If the problem persists, try to create a new user account and check. If the problem is resolved, then fix a corrupted user profile.

   

  Account for the new user: http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  Fix a corrupted user profile:

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

   

  Let us know if it helps!

• Adobe Air for iOS - SQLError: ' #3115 error ' no such table ".

  I'm developing Adobe Air application for iOS with sqlite on that. When running on my local machine, it worked like charm (add, edit and delete). Unfortunately, when tried to run on the iPAD, it gives me the following error:

  SQLError: Details ' Error #3115',:' no such table: ' tblEmploye ", operation: 'run', detailID:"2013".

  Here is my code when opening the sqlite database: * data is saved to the directory of the current application where all the files are stored:

         
          exampleDBFile = File.documentsDirectory.resolvePath("mydb.db");
  
          if (exampleDBFile==null || !exampleDBFile.exists) {
              MovieClip(root).mcSong.visible = false;
              MovieClip(root).mcAlert.visible = true;
              MovieClip(root).mcAlert.enabled = true;
              MovieClip(root).mcAlert.txtErrorMessage.text = "Database not found";
          }
          exampleDB = new SQLConnection();
          
          exampleDB.addEventListener(SQLEvent.OPEN, onExampleDBOpened);
          exampleDB.addEventListener(SQLErrorEvent.ERROR, onExampleDBError);
          
          //exampleDB.openAsync(exampleDBFile);
          exampleDB.open(exampleDBFile);
  

  I also tried to use the following but still no luck

  exampleDBFile = File.applicationDirectory.resolvePath("mydb.db");            

  using this, I get a different error: Error: Error #3104

  And here is the code for adding new entries

          
          sqlInsert = "insert into tblLyrics (empName, empDesc) values
                      ('"+ strReplace(txtSearchMe.text, "'", "") + "','"+ strReplace(txtContent.text,"'","") +"')";
          dbStatement.text = sqlInsert;        
          dbStatement.addEventListener(SQLEvent.RESULT, onDBStatementInsertResult);        
          dbStatement.execute();
  
  

  Hoping for your advice...

  Hello

  @uxavenue

  to add something to the post of samia:

  -on iOS your application directory is in 'read only' (at least when using native application)-so resources in the application directory (in the terminology of the Air - not iOS SDK SDK) may not be changed/written/updated

  -you could ship already created database sqlite with your application files, but must be copied to the writable to the application directory - for example documents. This directory is accessible via:

  File.documentsDirectory

  -When your application starts, you could do more:

  (1) build the path to the path of database documents

  (2) check if the database in this path exists (if this file exists)

  (3) if the file does not exist yet either copy in this path of the resource directory of the application (where you consolidate during the generation of project) OR create the new empty database using all these CREATE table and then INSERT statements required to create the new new copy of database

  (4) on each next start so check if the file exists at #2 jump creation/copy of database and simply start using it.

  Kind regards

  Peter

• Trying to get back to the factory State but in error (disabled: recovery partition is deleted)

  Microsoft support Hi I feel my laptop is runing slowly and I'm trying to get to the condition of the plant, and when I try it show me recuperator (disabled: recovery partition is deleted) can help me please

  Original title: salvation to microsoft support page

  How you restore the State of the plant is a process created by the manufacturer of your PC, not MS or Win

  Visit your PC manufacturers support pages to find out how to recover.

  If the hidden restore Partition has been deleted or corrupted, and assuming that you hadn't already done your recovery disk set you need to call the PC support to request the recovery disks

• no error as such code

  I use windows xp home edition and MS office 2007, at the time where I copied a picture of my word document and pasted on my desktop all my desktop icons are highlighted how to solve this problem.

  Make sure that the shadow option is actually enabled:

  1 right click on my computer.
  2. Select Properties.
  3. click on the Advanced tab in the dialog box.
  4. click on the settings button in the Performance Panel.
  5. click on the tab Visual effects in the dialog box.
  6. check the box whose title starts shadows fall for the icon to use...
  7. click on OK, OK.

  There are also three other reasons lost Icons transparency:
  1. If your background is transparent or animated GIF image.
  2. If you placed the Web content on the desktop.
  3. If you have chosen to lock the Web content on the desktop.

  You can check and correct all three in the display properties dialog box. Right-click on the desktop and select Properties. First click on the Desktop tab, select one of the default Windows background images and click on apply. Then, click on the button customize the desktop and click on the Web tab in the desktop items dialog box. If there is no items checked in the list of Web pages, then. Also disable the lock desktop items checkbox below. Click OK, click OK again.

  I hope I could help