Error reading disc after HD upgrade

Similar Questions

• Error reading disc after reinstalling xp

  I've seen similar positions but with no solution to this. Hope you can help. I updated my laptop drive and installed XP using the recovery disk. Formatted in NTFS ok. The installation was flawless. After restarting, I got a message "disc error". Reboot gives the same message. Thinking that I had a disk problem I used the soft Western Digital drive to check the drive and it is 100% OK. I used the low soft format the disk (write all zeros on the disk) and then again checked with the WD application. All tested OK. Then I used the XP Reinstall disk to format to ntfs and reinstall the operating system. I had the same installation without flaw and the same error at the end I repeated 2 times more tempting to quick format, slow format, etc but still the same error. The disc reads perfectly with a number of different applications until I have reinstall the OS. The laptop works very well with the old drive.

  Format.exe said it almost nothing about the condition of the disk. Chkdsk.exe /R tells you much more and diagnostic program by the disk manufacturer (which you can download) tells you more.

• Error "Cannot read disc" after nc4200 replacement hard drive

  Hi all

  I read through the postings but did not see an exact match for the issue I'm having.

  My 5 year old needed nc4200 finally a replacement hard drive.  I bought a new 120 GB ATA-6 WD Scorpio Blue 40 GB ATA-7 Toshiba plant.  I was able to clean up a few errors on the old disk and the Partition Magic 8.0 successfully used to copy all the data in a single primary partition on the new 120 GB drive using all available space.

  I started with success the drive on the Windows desktop using a separate post of full PC.  When I inserted the new, WD drive in my nc4200 however I got an error "cannot read disc" immediately after the MESSAGE.  The BIOS is a short wee on tests of diagnostic and other information on the hard drive, but I ran with success a test drive in the menu of the BIOS with the net results.

  I have advanced and updated the BIOS to version F.0F thinking there may be some 1024 cylinders deliver or other incompatibility big disk, but this new version also shows the error of reading.  At this point, I'm stumped.  Why this new boot in my desktop PC drive but fail in my nc4200?  What do I have to use some tools HP blessed to make this readable disk?

  Thanks in advance!

  Well, I guess you can call this one resolved.  I sent the WD Scorpio Blue 120 GB drive (model WD1200BEVE) and ordered a WD Scorpio Blue 80 GB (model WD800BEVE) instead.  I cloned my old Toshiba 50 GB 5400 RPM (model MK6026GAX) with Acronis True Image WD Edition.  I installed the new drive in my nc4200 and pulled upward on the first try!

  I'm still not sure why the 120 GB didn't work.  The only thing I noticed is that the done 120 GB one noise rattling and the 80 GB is not then maybe the drive was defective.  I'll never know however, if it was the drive or the size of the drive, that was the question, but I hope that this info will be useful to someone else looking to exchange a HD of aging in a nc4200.

• SlimType BD E DS4E1S will not read discs after windows update

  My laptop has a Slimtype BD E DS4E1S drive.  After doing upgrades with windows 7, it can now read all disks.  All MS suggests tried, but nothing has worked.  Don't ask, discs have been read in the same drive, before this problem started.  The computer is only a couple of months.  This utility shows no problem with the drive.  It just keeps telling me to insert a disc, such that no disk is detected.  Already tried changes to the registry (MS) and uninstall, reinstall the driver with no result.  Any suggestions?

  Hello

  I suggest you to wait for the manufacturer of your computer, ASUS responds again to you. It's a hardware problem and I suggest you contact the manufacturer of your computer for assistance.

  Kind regards.

• Error App 4950, after the upgrade to 11XE (Windows) of Apex 4.0 to 4.2.4

  Hi all

  After you upgrade a newly installed (Windows) 11XE of the Apex preinstalled (4.0) to 4.2.4

  http://127.0.0.1:8080/apex/f? p = 4950 no longer works.

  It gives me:

  	Error	Error processing request.
  		ORA-01403: no data found

  I can hardly imagine it is designed by design - at least I hope so.

  Is it possible to make it work again?

  Thanks and greetings

  André

  Mickael Pavan wrote:

  You must define a port other than 8080 after upgrade.

  Incorrect answer. There is no need to do it at all.

• THROWABLE-WAS-NULL error the connection after the upgrade to version 4.0.3

  I get a Java exception when I connect to Hyperic.  This started after I upgraded my server version Hyperic 3.2.4 to 4.0.3.  Everything else seems to work after I get the Java error, I would like to know how to solve this problem but it happens every time I log in.  Complete the below error and here is my server information.
  
  OS: RHEL 5, 64 - bit
  The Hyperic Version: HQ 4.0.3 build 953
  
  ===============================
  Exception:
  THROWABLE-WAS-NULL (to java.lang.Exception at org.hyperic.util.StringUtil.getStackTrace(StringUtil.java:409) at org.apache.jsp.common.GenericError_jsp._jspService (unknown Source) at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:97) at javax.servlet.http.HttpServlet.service(HttpServlet.java:810) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:252) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:173) at org.apache.catalina.core.ApplicationDispatcher.invoke(ApplicationDispatcher.java:672) at org.apache.catalina.core.ApplicationDispatcher.processRequest(ApplicationDispatcher.java:465) at org.apache.catalina.core.ApplicationDispatcher.doForward(ApplicationDispatcher.java:398) at) org.apache.catalina.core.ApplicationDispatcher.forward(ApplicationDispatcher.java:301) at org.apache.catalina.core.StandardHostValve.custom(StandardHostValve.java:362) at org.apache.catalina.core.StandardHostValve.status(StandardHostValve.java:283) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:136) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:105) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:107) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:148) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:856) at org.apache.coyote.http11.Http11Protocol$ Http11ConnectionHandler.processConnection (Http11Protocol.java:744) at org.apache.tomcat.util.net.PoolTcpEndpoint.processSocket) PoolTcpEndpoint.java:527) at org.apache.tomcat.util.net.MasterSlaveWorkerThread.run(MasterSlaveWorkerThread.java:112) at java.lang.Thread.run (Unknown Source))

  It is not a problem with the upgrade, there is a problem with the URL you probably have in your bookmark or browser history of 3.2. See:

  http://JIRA.Hyperic.com/browse/HHQ-2858

  In short, no access http://server/Login.do because SignIn.html redirection causes the stacktrace. Access / or SignIn.html to avoid the error.

• Satellite L300 - error reading disc so I can't start Vista

  Please can you help me?

  Have a Toshiba Satellite L300. All I get is disc read error has occurred, please press Ctrl Alt + Delete.
  How can I get to start again. I have no idea what it takes then just keep pressing Ctrl Alt + Delete and it says a disk read error has occurred.

  I'm going along in circles in. Running Windows Vista Premium.

  Hello!

  You can access the advanced boot menu if you press F8 after starting the laptop? Then you can start to the recovery Toshiba HDD option (select Repair my computer).

  If you can access the advanced boot menu, you must reinstall Windows Vista from the t. Therefore, you can use the Toshiba Recovery disk if you start from it.

  Good bye

• Error reading disc Y560d

  Last night, suddenly my laptop crashes and I decided to restart it but after the BIOS menu, there the "Disc Read Error - restart CTRL + ALT + DEL" Message and I cannot go further from here.

  What I've read I need to replace my HARD drive?

  If so, should I buy a new, or would it be better to call technical support in an attempt to replace.

  I am still under warranty.

  You should communicate with warranty, let them do it for you.

• ASR1004 - error of IPSec after ROMMON & Upgrade IOS - XE

  Hi all

  After updating the router ASR1004 S ROMMON 15.2 (1r) and IOS - XE 03.06.02.S, I get the following error messages:

  % IOSXE-3-PLATFORM: F0: cpp_cp: QFP:0.0 wire: 101% TS:00000059590688361391 IPSEC-3-HMAC_ERROR: IPSec Security Association receives an error HMAC, DP manage 5449

  Does anyone know, what is the problem with this error?

  Thanks in advance,

  Norbert

  Norbert,

  This means package was recived that has no verification of HMAC.

  If you upgrade to a version that contains this hotfix:

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtw69096

  you will get more information on packages like this.

  Marcin

• This connection is untrusted with error code error code: mozilla_pkix_error_v1_cert_used_as_ca) after the upgrade to Version 38 for my Web site.

  My site works fine with Firefox 35 version without any problems. but when I upgraded to version 38 I started getting the error code: mozilla_pkix_error_v1_cert_used_as_ca). I checked my certificate and is valid until the end of the year

  There are hundreds of variations within each major version of Firefox, so the cause of the problem might be hard to guess without more information.

  You want to post the URL of your site?

  If not, you could generate a report using this test page: https://www.ssllabs.com/ssltest/. Which often will identify the problem that Firefox has with the certificate.

• Notification of 'Syntax error' constant JavaScript after the upgrade to 17.0

  Almost on every page, I opened appears after notification ' error: error of syntax "JavaScript application. Even on this page where I fill in the form.
  I have to click 'OK' several times to clear.

  Same problem with the last update. In Safe Mode deleted SocialFixer. Which corrects the problem.

• HP Pavilion Notebook 15-p050ca: graphics driver error message started after the upgrade of Windows 10 model installed on #: G6U13UA #ABL

  I have recently upgraded to Windows 10 and since then, I received the following message through a game: "display Intel HD Graphics driver Driver for Windows 8 (R) stopped responding and has successfully recovered."

  I checked my graphics driver and it says that it is up-to-date.  I tried installing the latest drivers for my laptop model (according to the HP drivers page), December 15, 2015, installed without a problem, but no version has not fixed the problem.  An error message appears when I try to install the March and April, 2016 versions of graphics drivers, claiming that they are not compatible with my computer.

  I also tried the Intel and HP driver update utility and told me that my drivers are up to date.  However, when I look at the properties of my Intel(r) HD Graphics Family in Device Manager, I noticed that information on the events tab says: "peripheral PCI VEN_8086 & DEV_0A16 & SUBSYS_227E103C & REV_0B\3 & 11583659 & 1 & 10 still requires the installation."

  I don't know what needs update on my computer or if this driver is incompatible with Windows 10 and there is not yet an upgrade?  Advice or opinions would be appreciated!

  My computer model is the 15-p050ca HP Pavilion Notebook PC (ENERGY STAR) model #: G6U13UA #ABL and the graphics driver is version #: 10.18.15.4279

  I went back to 8.1 for Windows and ran the store several times and then reinstalled Windows 10.

  I watched the graphic version installed and version 20.19.15.4331 dated dated 18 November 2015, but he still claimed there was an update of the graphics driver.  I tried the update and it was version 10.18.15.4279 dated August 2015, which was the same version that was installed when I had problems (and the same version on the HP website), then I went back to the 20.19.15.4331 version.

  I tried all the graphics drivers listed for my computer on the HP support page and again, I had the same problems with them as I had before (either claim that my computer has no minimum requirements or my graphics driver crashing).

  With the current version (20.19.15.4331), my graphics driver has stopped at least for now crashing, but I assume that this is not a specific driver HP and is only based Intel?  If so, I recommend HP glance on the issue, I've had if they claim that these drivers are supposed to work for my computer when my computer is, in fact, not accept them.

• Driver video error Code 10 after the upgrade to Windows 7

  Upgrading to Windows 7 & have the following error messages:

  Standard VGA graphic card work not only can not start (Code 10)

  Converter USB - LAN has no driver

  SMA 851 X USB to Fast Ethernet Adapter

  During the initial installation of Windows 7 the monitor works but when Windows upadates are applied it gives the messages described above. Everything worked then on Vista... but also Vista would work!

  Dell does not have a driver for a monitor solution - 2 years. I was running as an extended desktop on a Dell Inspiron 6400 with 2 GB of RAM, new 500GIG Hitachi hard drives.

  Also cannot load the Office Small Business 2007 Business Contact Manager.

  Hi remaxguy,

  See the following article on setting error Code 10:

  http://support.Microsoft.com/kb/943104#appliesTo

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• ReadyNAS 104 does not start. Out_of_memory error 354. After the upgrade to 6.4.1 #26323717

  6.4.1 installed from 6.2.5 yesterday. Everything went well. Did all the "computation". has worked well.

  No not from one day to the next with 354 out_of_memory error. now, does not start.

  I tried reinstallOS. No luck.

  totally stuck and he needs for businesses!

  You could try RO mode, see https://community.netgear.com/t5/Using-your-ReadyNAS/Readynas-104-won-t-boot-Error-354-out-of-memory...

• Help! 100% reading disc after starting about 5 minutes windows 8

  I was not able to get your comand work, he said something error with '-start the trace "command

  I did it with the program Windows Recorder PErformance with Performance scenario set on Boot.

  My pc automatically rebooted 3 times and the recorder ran 3 times with a timer that makes my pc restarts when it ended. Here are the files.

  1st round

  2nd round

  3rd run

  ARE

  The only successful even partially.  Race 2 & 3 had no useful information

  It seems that your connection to Facebook is the question (the modern UI app or someother Facebook app?).  I have no idea what app or how you are connected but that connection pinned the HD 100 & 180 seconds.

  All that 'sync', is the cause of the collapse of the HD.