Failure to supply MD3200i

Similar Questions

• Failure to supply ink message Officejet Pro 8500 has

  I have a 8500 has only a few months, on an iMac.  I have frequent printing problems where the print queue shows the message "failure of ink.  When I power cycle the printer, it almost always clears the error and the print job goes by, and I can print multiple jobs immediately without problem.  So next time rather than later, I need to turn it and turn it on again.

  Any idea what's going on?  Is it a faulty print head, as some research suggests?  If so, I guess I need a warranty replacement...

  Oh, oops, I thought the 8500.  Too many models .

  Here are a few ideas:

  1. remove all the ink cartridges.  Raise the lever on the right side of the cart and remove the printhead.  Make sure that the electrical contacts are clean on the print head and transport.  All reinsert and try again.

  2. soft reset of the printer: turn off the power.  Turn off the power at the back of the printer for 2 minutes.  Plug in and turn on.

• IPMI error code 2900:0221 Power supply failure detected on PE R710

  My VMware ESXi host recently took itself offline. When I was looking for the root cause, I ran a diagnostic test on my R710 EP and the following error is generated:

  Error code: 2900:0221.
  MSG: IPMI - : power supply: sensor power supply (status) failure detected 'PS 2 '.

  The given error code and message can serve as Support to help diagnose the problem.
  Want to continue his tests?

  -end of the error message-

  I saw a post online to update the BIOS and firmware, I did. We are now running BIOS version 6.4.0. I restarted the test with the same results. Any ideas on what I can do to fix this? If the problem is indeed a power supply failure or a sensor on a feed, how do I know which one is bad? Lights on both power supplies are similar to the rear of the server. This unit is no longer under warranty.

  Andoven,

  Error Code: 2900:XXXX is historical, referring to recent system errors. It is usually good to clear the logs of equipment before running the system diagnostics. Included update for your firmware firmware on the power?  I guess that your two power supply status LEDs are both green.  If installed, clear the logs in the OMSA and then reconnect the power supply on the right (2 PSU) and see what OMSA reports.

  Let us know the status of the block of POWER 2 in OMSA and the current version of the firmware.

• Qosmio X 870 - alleged supply failure

  Hello

  I bought a Qosmio x 870 about 10 months or so there, and about 2 months ago he completely closed and did everything at stake. She had known some of these prior events, I tabled overheating, but since the last of them, I assumed it was a motherboard problem.

  I guess I'm still under warranty, but I was not willing to pay the price "advanced problem" of the suspected motherboard issue but now that I had a family friend of the test with a multimeter voltage, he thinks that maybe it's food like any testing Cordon Bleu, they seemed very well up until the adapter is connected when reading came through that the blue of the adapter cord may have something wrong.

  I'm curious to know, what I have to return the pc just to get a replacement Toshiba power?

  > I'm curious to know, what I have to return the pc just to get a replacement Toshiba power?
  Unfortunately I can't provide the answer to your question but I would recommend to call the nearest service, explain the situation and they will explain what you can do about it.

  Addresses and phone numbers, you can find on http://www.toshiba.eu/innovation/generic/ASP_SUPPORT/

• Satellite A100-TA9: failure of the power supply cord - where to get a new

  Recently my power cord has stopped working on my Satellite A100-TA9 system.
  My system warranty has expired and passes through 'Authorized support vendors' Toshiba was useless.

  Anyone know where I can get a replacement power cord?
  I live in Toronto, Canada.

  Thank you

  Hello

  > My system warranty has expired and passes through 'Authorized support vendors' Toshiba was useless
  I n think so.

  First of all, you know that a disassembly of the laptop is very delicate and not easy. ASP technicians have sufficient experience to perform this replacement with touch course. I mean you have no risk something would be accidentally damaged during disassembly procedure.

  Second, you must contact the local ASP to get a compatible power cord.
  I think you'd need a power cord which has been designed especially for the A100 series.
  Guys could order directly from Toshiba.

  See you soon

• Error 1074135030 and hyper-Terminal failure while communicating with the power supply

  Hello

  I use the serial port to communicate with power XG XG 8-100 (series) by Xantrex (Sorensen).

  I could not find the driver in IDNE, but I found one on the site of the company that is http://www.programmablepower.com/products/XTR/XTR_Downloads.htm , when I run the example that I get the below error:

  Error 1074135030 has occurred to be initialized with Options.vi of DC850W

  Driver status: (Hex 0xBFFA000A) check that the name of the library (C:\DC850W\DC850W_32.dll) and (DC850W) prefix are correct.

  I don't know what the problem is with the name of the library that makes such a problem.

  FYI, I tried to communicate with the device using the hyper terminal, but there is no answer. When I check the MAX, it seems that everything is OK, that the State is: the device works properly!

  Do you have any suggestions for me?

  Any help or suggestions appreciated because I'm messed up with this and I don't know how to go further.

  ELA

  
  

• Pavilion 15 p 146: HP Pavilion notebook - failure of power supply or a laptop?

  My Pavilion laptop is 4 weeks old. This morning, it worked, but I noticed that it doesn't seem to be load - the remaining battery indicator was stuck at 11 percent and there was no indication that he was in charge. Finally the laptop has stopped working.

  Now I am unable to return to power.

  I tried to remove the battery completely and using alternating current only, but it will not turn on. When the AC is attached no lights don't appear next to the power socket. However if I press and hold the power button, the LED next to the power jack on the laptop flashes 3 times. Release the power button then hold again produced the same results - the LED flashes 3 times.

  Note that if I turn off the AC altogether the does not blink at all, which suggest that some powers gets through.

  How can I determine if the problem is with the AC adapter and not an internal problem with the laptop?

  Thank you

  When an AC adapter is plugged in and OK it will be a weirdo directed. If the power led does not illuminate, then this is a diagnosis that lets you know that it doesn't have the power adapter.

  The power adapter is a unit that can be replaced under warranty without charge to you.

  Contact HP for warranty repair.

• PowerEdge 2950 - p.supply failure [MS]

  Buongiorno,

  Ho due Server PowerEdge2950 ()
  As con UN guasto alimentatore CIASCUNO.

  Come posso di ricambio party puzzle

  Grazie
  Mario Mussatti

  Inviati QUOTES.

  Buona day

  Manual

• Supply in host failure detection

  I have written a test for feeds on my 5.5 ESX hosts. It tests whether the power is reduced to zero watts.

  I will use it, then fire a stop appropriate if raw power is lost.

  Harware: HP Proliant DL360p Gen8

  ESXi Build: 5.5.0 2456374

  # Script to detect if a diet does not have any juice.

  # Normally DL360p Gen 8 sensors 0.53 or 0.54

  # Tim 15/04/2015

  # Version 1.0

  SENSOR = $1

  POWER_IN = "/ bin/esxcli material ipmi sdr list |" grep ' ^ $SENSOR ' | Cut - c65 - 67'

  POWER_OUT = "/ bin/esxcli material ipmi sdr list |" grep ' ^ $SENSOR ' | Cut - c96 - 98'

  If [$POWER_OUT - eq 0]

  then

  echo ZERO POWER OUT

  Output 1

  FI

  output

  Is there a better way to this script?

  I thought that this, but then why stop the host? -If anything, I think it would be better to replace the mode of vMotion & maintenance PSU or trigger failed before anything else?

  That said, the script seems correct, I'd be looking in the porter to PowerCLi however

• Metal nu supply - failure to 'BONES to prepare for the installation of network.

  Hi all
  
  We have successfully up to 12 c, registered a management of LMOS server - but I would now get the bare metal, provision of work.
  
  Company > Provisioning & patching > Bare Metal Provisioning > Infrastructure tab, we have implemented the server of the scene, DHCP server, boot server & deposit RPM - all (according to us!) properly.
  
  The server RPM in a box of OEL 5 on LSN and defined as server YUM, subscription channels OEL5 & LMO. These were then downloaded into/var/www/yum by YUM script. We can browse the repo on HTTP - everything looks OK.
  
  Under the tab "Mutations", we then available to a LMO server, fill in all the necessary fields, nothing special. We check the boxes to perform the prerequisite check on stage and boot servers - these pass.
  
  That we completed, submit work and to monitor progress - go us beyond "activities preliminary staging.
  
  However, the job fails to 'run OS Staging Directive"- specifically the task of"Preparing the OS for network installation".
  
  The log file shows the following error: that we are mistaken:
  
  wget http://yum.yumserver.local/yum/OracleVM/OVM3/3.0.2/base/x86_64/isolinux/vmlinuz vmlinuz - O
  Connection to yum.yumserver.local | 192.168.252.53 |: 80... connected.
  Query HTTP sent, awaiting response... 404 not found
  
  Our basic URL yum repository has been defined as http://yum.yumserver.local/yum/OracleVM/OVM3/3.0.2/base/x86_64 on the Infrastructure tab - that we think is correct?
  
  We can connect to the fine BASE URL at the same time the Enterprise Manager server and staging server.
  
  Any ideas?
  
  Jeff

  Hi Jeff,

  I listed down an example of configuration to the tftp Protocol & dhcp server as well as the values of flow that we expect in the infrastructure tab:

  TFTP root directory (in etc/xinetd.d/tftp): / tftpboot
  Input file name in the dhcp file (/ etc/dhcpd.conf): "linux-install/pxelinux.0".
  located pxelinux.0 to the: / tftpboot/linux-install

  Values of infrastructure tab:
  Startup directory: / tftpboot/linux-install
  file DHCP: /etc/dhcpd.conf

  Thank you
  Sachin.

• Hardware failure if I open Adobe apps or iTunes

  I'm having a horrible time, sorting by a hardware failure in a 3.5 GHz 6-Core MacPro problem. After that he crashed during his sleep, I am not able to launch Adobe applications or iTunes without another immediate material failure. I trashed every imaginable preference and reinstalled the new software system to no effect. Can someone look at the panic report and make some sense? Thank you...

  Anonymous UUID: C1EFD5AA-D9A3-3AD8-D9AC-86E6088D3498

  Fri Sep 23 08:21:34 2016

  Panic report *.

  panic (cpu 0 0xffffff7f8c09f9ce appellant): "ACPI \"PWRD\ "with zero power failure: < rdar://problem/15746463 > ' @/Library/Caches/com.apple.xbs/Sources/AppleGraphicsC ontrol/AppleGraphicsControl-3.12.8/src/AppleMGPUPowerControl/kext/AMPCPowerManag, .cpp: 511»»»

  Backtrace (CPU 0), frame: return address

  0xffffff93ebcf3db0: 0xffffff80098dab52

  0xffffff93ebcf3e30: 0xffffff7f8c09f9ce

  0xffffff93ebcf3e80: 0xffffff7f8c09eed2

  0xffffff93ebcf3ec0: 0xffffff7f8c09d6b9

  0xffffff93ebcf3f10: 0xffffff7f8c09dc0f

  0xffffff93ebcf3f40: 0xffffff8009eb3111

  0xffffff93ebcf3f80: 0xffffff8009eb330c

  0xffffff93ebcf3fb0: 0xffffff80099c9117

  Extensions of core in backtrace:

  com.apple.driver.AppleMGPUPowerControl (3.12.8) [CB4BA03A-3AA5-34F1-B951-4A2F8352 8E48]@0xffffff7f8c097000-> 0xffffff7f8c0a3fff]

  dependency: com.apple.driver.AppleBacklightExpert (1.1.0) [C49819CE - 729A - 36B 2 - 9AC1 - 744A43DC23 6F]@0xffffff7f8c08f000

  dependency: com.apple.iokit.IOPCIFamily (2.9) [5447B943-A94D-3BD4-A60F-98B24D19CE93] @ 7f8a12c000 0xffffff

  dependency: com.apple.driver.AppleGraphicsControl (3.12.8) [C57F5F56-2229-365F-9765-F24AA4687 584]@0xffffff7f8c094000

  dependency: com.apple.iokit.IOACPIFamily (1.4) [5D7574C3-8E90-3873-BAEB-D979FC215A7D] @0xfffff f7f8a91e000

  dependency: ffff7f8ad65000 @0xff com.apple.iokit.IONDRVSupport (2.4.1) [4EB2843C-C821-3AD0-B333-575FD6ED6FB1]

  dependency: com.apple.iokit.IOGraphicsFamily (2.4.1) [A360453D-2050-3C49-A549-AC0DD5E87917] @0 xffffff7f8a2d1000

  Corresponding to the current thread BSD process name: kernel_task

  Mac OS version:

  15 1004

  Kernel version:

  15.6.0 Darwin kernel version: Mon Aug 29 20:21:34 PDT 2016; root:XNU-3248.60.11~1/RELEASE_X86_64

  Kernel UUID: E349749B-3303-3DDF-959C-B5885A0E1F6E

  Slide kernel: 0 x 0000000009600000

  Text of core base: 0xffffff8009800000

  Text __HIB base: 0xffffff8009700000

  Name of system model: MacPro6, 1 (Mac-F60DEB81FF30ACF6)

  Availability of the system in nanoseconds: 337233042670

  last load kext to 166512757592: com.apple.driver.AppleFireWireStorage 3.7.1 (addr 0xffffff7f8bba8000 size 20480)

  kexts responsible:

  com.paceap.kext.pacesupport.snowleopard 5.8

  com.shinywhitebox.iShowU - Audio-Capture 1.0.2

  com Blackmagic - design.desktopvideo.iokit.framebufferdriver 10.4.3

  com.apple.driver.AppleFireWireStorage 3.7.1

  com.apple.driver.initioFWBridge 3.7.1

  com.apple.driver.IOFireWireSerialBusProtocolSansPhysicalUnit 3.7.1

  com.apple.driver.LSI_FW_500 3.7.1

  com.apple.driver.Oxford_Semi 3.7.1

  com.apple.driver.StorageLynx 3.7.1

  com.apple.driver.AGPM 110.22.0

  com.apple.driver.ApplePlatformEnabler 2.6.0d0

  com.apple.driver.X86PlatformShim 1.0.0

  com.apple.driver.AppleOSXWatchdog 1

  com Apple.filesystems.autofs 3.0

  com.apple.driver.AppleHDAHardwareConfigDriver 274.12

  com.apple.driver.AudioAUUC 1.70

  3.12.7 com.apple.driver.AppleGraphicsDevicePolicy

  com.apple.driver.AppleHDA 274.12

  com.apple.driver.AppleUpstreamUserClient 3.6.1

  com.apple.driver.AppleMCCSControl 1.2.13

  com Apple.Driver.pmtelemetry 1

  com.apple.kext.AMDFramebuffer 1.4.2

  com.apple.iokit.IOUserEthernet 1.0.1

  com.apple.iokit.IOBluetoothSerialManager 4.4.6f1

  com.apple.AMDRadeonX4000 1.4.2

  com.apple.Dont_Steal_Mac_OS_X 7.0.0

  com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0

  com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.4.6f1

  com.apple.driver.AppleHV 1

  com.apple.driver.AppleLPC 3.1

  com.apple.driver.AppleThunderboltIP 3.0.8

  com.apple.kext.AMD7000Controller 1.4.2

  3.12.8 com.apple.driver.AppleMGPUPowerControl

  com.apple.driver.AppleIntelSlowAdaptiveClocking 4.0.0

  com.apple.driver.AppleFIVRDriver 4.1.0

  com.apple.driver.AppleIntelMCEReporter 107

  com.apple.driver.AppleUSBDisplays 378

  com.apple.iokit.IOBluetoothUSBDFU 4.4.6f1

  com.apple.iokit.SCSITaskUserClient 3.7.7

  com.apple.driver.CoreStorageFsck 517.50.1

  com.apple.driver.AppleFileSystemDriver 3.0.1

  com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1

  com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0

  com.apple.BootCache 38

  com.apple.driver.AppleUSBODD 3.7.1

  com.apple.driver.AppleUSBStorageCoexistentDriver 3.7.1

  com.apple.driver.AppleFWOHCI 5.5.4

  2.8.5 com.apple.iokit.IOAHCIBlockStorage

  com.apple.iokit.AppleBCM5701Ethernet 10.2.0

  com.apple.driver.AirPort.Brcm4360 1040.1.1a6

  com.apple.driver.usb.AppleUSBEHCIPCI 1.0.1

  com.apple.driver.AppleAHCIPort 3.1.8

  com.apple.driver.AppleACPIButtons 4.0

  com.apple.driver.AppleACPIEC 4.0

  com.apple.driver.AppleRTC 2.0

  com.apple.driver.AppleHPET 1.8

  com.apple.driver.AppleSMBIOS 2.1

  com.apple.driver.AppleAPIC 1.7

  com.apple.driver.AppleIntelCPUPowerManagementClient 218.0.0

  com Apple.NKE.applicationfirewall 163

  com Apple.Security.Quarantine 3

  com.apple.security.TMSafetyNet 8

  com.apple.driver.AppleIntelCPUPowerManagement 218.0.0

  com.apple.iokit.IOFireWireSerialBusProtocolTransport 2.5.1

  com.apple.iokit.IOFireWireSBP2 4.2.7

  com Apple.kext.Triggers 1.0

  com.apple.driver.DspFuncLib 274.12

  com.apple.kext.OSvKernDSPLib 525

  com.apple.driver.AppleSMBusController 1.0.14d1

  com.apple.iokit.IOSurface 108.2.3

  com.apple.iokit.IOSerialFamily 11

  com.apple.iokit.IOAcceleratorFamily2 205.11

  com.apple.driver.CoreCaptureResponder 1

  com.apple.driver.IOPlatformPluginLegacy 1.0.0

  com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.4.6f1

  com.apple.iokit.IOBluetoothFamily 4.4.6f1

  com.apple.driver.AppleHDAController 274.12

  com.apple.iokit.IOHDAFamily 274.12

  com.apple.iokit.IOAudioFamily 204.4

  com.apple.vecLib.kext 1.2.0

  com.apple.driver.AppleSMBusPCI 1.0.14d1

  com.apple.kext.AMDSupport 1.4.2

  3.12.8 com.apple.AppleGraphicsDeviceControl

  com.apple.iokit.IOFireWireIP 2.2.6

  3.12.8 com.apple.driver.AppleGraphicsControl

  com.apple.driver.AppleBacklightExpert 1.1.0

  com.apple.iokit.IONDRVSupport 2.4.1

  com.apple.iokit.IOGraphicsFamily 2.4.1

  com.apple.driver.X86PlatformPlugin 1.0.0

  com.apple.driver.AppleSMC 3.1.9

  com.apple.driver.IOPlatformPluginFamily 6.0.0d7

  com.apple.iokit.IOSlowAdaptiveClockingFamily 1.0.0

  com.apple.driver.AppleThunderboltEDMSink 4.1.1

  com.apple.driver.AppleThunderboltDPOutAdapter 4.1.3

  com.apple.driver.AppleUSBComposite 900.4.1

  com.apple.iokit.IOUSBHIDDriverPM 900.4.1

  com.apple.driver.AppleUSBHIDMouse 185,3

  com.apple.iokit.IOUSBHIDDriver 900.4.1

  com.apple.driver.AppleHIDMouse 185,3

  com.apple.driver.AppleHIDKeyboard 181

  com.apple.driver.usb.IOUSBHostHIDDevice 1.0.1

  com.apple.driver.AppleThunderboltPCIUpAdapter 2.0.2

  com.apple.driver.CoreStorage 517.50.1

  com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.7.7

  com.apple.iokit.IOBDStorageFamily 1.8

  com.apple.iokit.IODVDStorageFamily 1.8

  com.apple.iokit.IOCDStorageFamily 1.8

  com.apple.iokit.IOSCSIBlockCommandsDevice 3.7.7

  com.apple.iokit.IOUSBMassStorageClass 4.0.2

  com.apple.iokit.IOUSBMassStorageDriver 1.0.0

  com.apple.iokit.IOSCSIArchitectureModelFamily 3.7.7

  com Apple.Driver.USB.cdc 5.0.0

  com.Apple.Driver.USB.Networking 5.0.0

  com.apple.driver.usb.AppleUSBHostCompositeDevice 1.0.1

  com.apple.driver.usb.AppleUSBHub 1.0.1

  com.apple.driver.AppleThunderboltDPInAdapter 4.1.3

  com.apple.driver.AppleThunderboltDPAdapterFamily 4.1.3

  com.apple.driver.AppleThunderboltPCIDownAdapter 2.0.2

  4.6.1 com.apple.iokit.IOFireWireFamily

  com.apple.driver.AppleThunderboltNHI 4.0.4

  com.apple.iokit.IOThunderboltFamily 6.0.2

  com.apple.driver.AppleXsanScheme 3

  com.apple.driver.usb.AppleUSBXHCIPCI 1.0.1

  com.apple.driver.usb.AppleUSBXHCI 1.0.1

  com.apple.driver.AppleUSBMergeNub 900.4.1

  com.apple.iokit.IOEthernetAVBController 1.0.3b3

  com.apple.iokit.IO80211Family 1110.26

  com.apple.driver.mDNSOffloadUserClient 1.0.1b8

  com.apple.iokit.IONetworkingFamily 3.2

  com Apple.Driver.corecapture 1.0.4

  com.apple.driver.usb.AppleUSBEHCI 1.0.1

  com.apple.iokit.IOAHCIFamily 2.8.1

  com.apple.iokit.IOUSBFamily 900.4.1

  com.apple.iokit.IOUSBHostFamily 1.0.1

  com.apple.driver.AppleUSBHostMergeProperties 1.0.1

  com.apple.driver.AppleEFINVRAM 2.0

  com.apple.iokit.IOHIDFamily 2.0.0

  com.apple.driver.AppleEFIRuntime 2.0

  com.apple.iokit.IOSMBusFamily 1.1

  com Apple.Security.sandbox 300.0

  com.apple.kext.AppleMatch 1.0.0d1

  com.apple.driver.AppleKeyStore 2

  com.apple.driver.AppleMobileFileIntegrity 1.0.5

  com.apple.driver.AppleCredentialManager 1.0

  com.apple.driver.DiskImages 417,4

  com.apple.iokit.IOStorageFamily 2.1

  com.apple.iokit.IOReportFamily 31

  com.apple.driver.AppleFDEKeyStore 28.30

  com.apple.driver.AppleACPIPlatform 4.0

  com.apple.iokit.IOPCIFamily 2.9

  com.apple.iokit.IOACPIFamily 1.4

  com Apple.KEC.pthread 1

  com Apple.KEC.corecrypto 1.0

  com.apple.kec.Libm 1

  I have similar problems, but do not have a definitive answer to Apple. They replaced my D500 cards, graphics & the power supply but the plant still Mac Pro. According to the Apple phone support, looks like my logic board is bad. You will need to visit the Apple Store again to see what happens.

• Beats studio 2.0 Wireless pairing is a failure.

  Beats studio 2.0 Wireless pairing is a failure. They will not go into the pairing mode and the supply remains white Uni light. After pressing the button "b" for 2 seconds, nothing happens. I have devices are not as available to connect to. Does anyone else have this problem?

  Contact Beats.

  Barry

• Power supply selection guide

  This MOD can make a post-IT.

  Here is a general guide on how to select a power supply for your HP desktop computer.  The majority of the standard ATX power supply (PSU) must fit in an envelope of HP.  The exception would be a slim casing or the esoteric Merle.

  Looking for a certification 80 + on the PSU to save electricity.  A PC is normally idle or operate at low load 75% of the time.  Therefore, to find a power supply which is more effective in the range 50 - 90W.  A power supply 80 + 350W reaches the level of efficiency of 80% at the exit of 70W (20% of rated output).  The output must be greater than 140W to achieve the same level of efficiency of a PSU of 700W 80 + equivalent.  So choose a power supply that is rated at 25% more than the maximum load of the ACTUAL spending of the rig you will save more of $ on electricity.

  A modern PSU is designed to achieve maximum efficiency between 20 and 80% of the nominal power.  Running a power supply above 80% charge level will result in excessive heat, noise and premature failure.

  A platform Nvidia GeForce GTX 280 (1024 MB of RAM) will rely on 350W max to the wall.  Taking into account the effectiveness of a block of power SUPPLY 80 +, the actual load on the power supply is only 280W (350 x 0.80).  To calculate the required power supply, multiply the actual load by 1.25 (25% margin).  In this case we only need a PSU 350W (280 x 1.25) to run this GPU.

  Let's apply what we know of a rigging of Radeon HD 4870 (512 MB RAM).  290W max to the wall.  Actual load is 290W x 0.80 or 230W.  Now, apply the 25% margin rule and we come to a requirement of 290W PSU (230W x 1.25).  Even if we apply a safety margin of 50%, the power required is always under 350W (230W x 1.50).

  There are no overspec need the power supply by 50%, unless you run your PC up 24/7.  Don't forget that there is a huge variation in the quality of the PSU and side.  Maybe a good 500W PSU is not able to provide as much energy as a quality 350W.  Antec Earthwatts/NeoPower/TruePower and Corsair Seasonic are widely available at several American retailers of quality units.

  High-end power supplies number will need additional power supply PSU in the form of one or two 6/8 pin plug GPU.  You can buy an adapter to convert a molex 4pin to plug 6-pin power of GPUS.

  http://www.TomsHardware.com/reviews/GeForce-Radeon-power, 2122 - 3.html

  Hi Nautsj,

  You need to open your PC and measure the physical dimensions of your diet. Here is a list of the things to consider:

  1. technical characteristics
  2. the total power - important
  3. amperage 12 + v - important
  4 modular - is not required, but I like the flexibility
  5. guarantee
  6 i7 and SLI ready
  7. energy efficiency
  8 cost
  9. size - standard ATX PSU is 5.5 "by 5.9" by 3.4 "give or take a few tenths
  10. a single + 12 volt rail is a better choice.

  www.Newegg.com has many choices of power supplies. Corsair, OCZ, Rosewill, Thermaltake...

  The typical EVGA GTX 570 in 9 "long.  The adjacent slot on the PCI-E x 16 slot must be vacant.  Open your PC and do some measures so that you know for sure if the card fits.  According to me, it will fit.

  For what is a PSU, Corsair CX600has very little growth, but the Corsair HX650gives you plenty of space to grow.

  I use the HX650 in two PC.  It is a modular model in order to have better options with the selection of cable.

  "How-to" HP articles should be useful.

  TIP: When installing the power supply, unlock the scanner and slide it forward to facilitate the removal and installation of the new power supply.

• Corsair POWER supply update does not post, powers of the powers of 5 seconds down and loops...

  Have the HP Pavilion Elite m9650f with motherboard replaced in April 2012 class good to go.

  Replaced the stock GPU Nvidia GeForce 9800 GT with a Zotac GTX 560 Ti GPU and

  the stock HP 460 Watt power supply with a W0388RU Thermaltake TR2 600 Watt PSU in may 2012.

  All goes well until October 2012.

  PC randomly starts shutting itself off the coast and not feed until I have unplug the power cord and wait 5-10 minutes.

  Finally, he stopped turning on all together.  Reinstall all power PSU connectors, etc.  same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstall the stock HP 460 Watt PSU, now everything works fine.

  Thought it was a premature failure of Thermaltake PSU.

  Bought and installed a Corsair CMPSU - 850TXV2 850 Watt power supply for a few days but still not good to go.

  Lights, fans spin, but no MESSAGE, no video, tracks for all

  5 seconds, stops, turns on itself over and over again.

  Reinstall all power PSU connectors, etc. same result.

  Removed all cards, etc, same result.  Cards reinstalled one by one, etc., same result.

  Reinstalled the HP PSU stock, now everything works perfectly again.  ?

  Spends hours reading the forums...

  Some say that the RAM may not report correct voltage for power supply.

  If so, what can I change RAM voltage in the BIOS?

  Others say reset CMOS I did, same result.

  And someone on this forum HP thought that perhaps the Pegatron IPMTB-TK

  Card mother Truckee can only accommodate up to 750 Watts POWER supply.

  Any ideas?

  Can I get away with just using my HP 460 Watt power supply after all stock?

  Thank you.

  I have an additive to add to this topic.

  To refresh, my questions focus on a possible shift of the power supply and card mother specs:

  What is an ATX 12 v 2.0 and above technical problem or a power CAP problem?

  I posted my questions on the Forum of power SUPPLY Corsair PSU

  at the same time and I paste it here now, a response

  to GUY of RAM.

  "Hey RAM GUY."
  
  Sorry I couldn't answer until now.
  
  Please specify the difference between the ATX 2.0 specification and 2.01
  
  Spec that the negative - 5 v Rail is not present in the 2.01 spec and
  
  beyond.  As I mentioned previously, the Thermaltake PSU that has been
  
  running in my 2009, HP i7 tour for 7 last month said 12 volt ATX 2.2
  
  on the case and even if the power supply HP OEM said 12 volt ATX
  
  2.0 in the technical literature, that I found on Google, the real PSU I have does not work
  
  have any note on the case ATX specification.  So I think it's safe to say, my
  
  motherboard does not have the negative Rail v-5 at which he played
  
  nicely with 12 volt ATX 2.2 spec, until recently.
  
  Although theoretically it is supposed to be no limit on the amount of
  
  Absorbed power, you can use to power your motherboard, the motherboard because
  
  is supposed to use only what suits him and cap the rest, it seems that the OEM
  
  can dial up limitations of power if they deem necessary.
  
  Could be as simple HP, without wanting to compete with some of his HPs
  
  Professional workstations, caps so power on some Pavilion Elite
  
  Series models to prevent them from becoming a much cheaper
  
  solution.
  
  In any case, I think that all the available information, digested, he does not speak
  
  Specification of the ATX, but rather my motherboard HP has a limit of 650 Watts of power
  
  If I think that I read that someone else got the same motherboard goes with
  
  750 watts, but I do not remember where to find this announcement. »
  
  I'm back and Yes!
  
  Thanks again Lasvegaswireman!

• Failure of disk hard A10 and replacement - using recovery disks?

  I have a Satellite Pro A10, who suffered a hard disk failure. I replaced the hard drive (with a non-toshiba drive) but cannot load the OS etc. from the recovery disks provided with the computer when new. When you start the computer upwards with recovery No. 1 disc in the CD drive I get the message "system no valid disk, replace the disk and then press any key" any suggestion as to the repair would be welcome.

  Hello

  Well, it's not easy to say why it doesn t work. Have you tried to start the recovery with the second disc? Have you checked whether the CD 1 is a scratch?
  If it is not possible to recover the operating system with the supplied restore CD, I suggest to ask ASP for a new recovery CD.

  Good bye