FCoE storage direct connect in 1.4?

Similar Questions

• storage direct connect

  Hello

  Once we have the new version 2.1 (1) for UCS Manager I would like to know the following when using the interconnections of fabric FC Switch Mode:

  (1) is it possible to connect a storage array supported directly on the fabric of interconnections at the same time to have a Nexus/SDM connected as an uplink switch?

  2) that will make the zoning in the second case (MDS/Nexus or fabric interconnects)?

  (3) is it possible to implement the zoning between two bays of storage attached to the interconnection fabric so that it is possible to replicate storage of a table to another?

  (4) if the storage array 1 is connected directly on the fabric of interconnections Bay storage 2 is connected to the uplink of Nexus/MDS, is it still possible to the zone and perform a replication between the two tables?

  Thank you

  Hi Dani,

  Answers to your questions below.

  (1) is it possible to connect a storage array supported directly on the fabric of interconnections at the same time to have a Nexus/SDM connected as an uplink switch?

  [ANSWER] Yes, you can connect a storage array directly to the INSTITUTION, but make sure that you put it in a different VSAN that connected to MDS/N5K. You can activate zoning on this new VSAN and zoning in FI.

  2) that will make the zoning in the second case (MDS/Nexus or fabric interconnects)?

  [ANSWER] Your existing zoning will remain the same and the zoning will be in MDS/N5K. This VSAN is not enabled in UCS of zoning.

  (3) is it possible to implement the zoning between two bays of storage attached to the interconnection fabric so that it is possible to replicate storage of a table to another?

  [ANSWER] Replication is not possible through FI. If you have additional ports in the new storage, you can connect the ports to MDS/N5K and manage replication through them.

  (4) if the storage array 1 is connected directly on the fabric of interconnections Bay storage 2 is connected to the uplink of Nexus/MDS, is it still possible to the zone and perform a replication between the two tables?

  [ANSWER] No, you wouldn't be able to do this because they will be in different VSANS. Again, this can be managed as described in point 3 above.

• FCoE directly connect to VNX5300 with no switch zoning

  I was wondering if anyone has any experience with this unit or a similar facility. I find no decent documentation to help us decide if it is a legitimate set upward for a production of about 16 servers 3 chassis environment. Our expert Cisco has ever put up a UCS environment with a direct connection to the San via FCoE and intuitively is against it, as we do not expect to use a switch to zoning.  Is there a real risk in the present? It will support in the future?

  Hi Henry,.

  If you look at the following document:

  http://www.Cisco.com/en/us/docs/switches/Datacenter/MDS9000/interoperability/matrix/Matrix8.html

  See point number 3, the direct model to support tethering still requires a SDM or N5k upstream to provide this information.

  . / Afonso

• EqualLogic PS6100X: direct connections (double) iscsi to 3 vmware ESX host

  Hello

  Due to the reduction of costs, we integrate

  1 x ps6100x Dell Equallogic (2 controllers to each 4 ports)

  3 x dell poweredge r720 (each have 2 ports dedicated for trafficking SAN storage)

  vSphere 5.5 (shared storage on the San)

  Without the use of SAN switches. Each host has dual direct connection (1 to each SAN controller) with the initiator iscsi software.

  We did before with Dell MD3200i, who has also 2 controllers and 8 ports, so we expect no problems.

  But now that I have read on the Equallogic, I'm starting to become uncertain if this Setup will work?

  I know that this is not recommended, but at this point, my only concern is that it will work (even with less performance).

  Can you please give me some advice on this?

  Best regards

  Joris

  P.S. If this is probably NOT possible, what would be the best/low average cost to make this possible?

  I've seen this failure at work, as in the connections dropped, BSOD was virtual machines with a single host with no switch.  iSCSI traffic tends to be very burst, which is having when the right switch pays you back.

  Re: 3750 X are those good switches, there is some adjustment settings that need to be addressed.  Also to solve a flowcontrol problem download the most current IOS firmware.

  For such a small group / number of servers, the stacked 2960 would be OK.  Perhaps to problems later if you need to scale this environment.  lack of 2960 allocate buffer, then you want to start without Jumbo frames, all enter into stable and of good practices.  So maybe later try enabling it.  3750 X works very well with Jumbo and Flowcontrol active BTW.

  These choices are better than no switch miles.  3750 x were pretty expensive last time I looked.  Unless you have a little already.  If you share them with the rest of the traffic that is not optimal, but at least put all ISCSI traffic on its own VIRTUAL local network.

  4948 are the right choice.  Some high-end HP switches.  Step away from the elders, like 2810 or 2824/48.  They seem to be there for cheap $$ but are designed for GbE Office not GbE iSCSI.

  Kind regards

• HP OfficeJet 200 series Mobile: 3 Surface Pro WIndows 10 - can't re eastablish wi - fi direct connection

  Hello

  We managed to connect our Surface Pro 3 Windows 10 running on a mobile printers HP OfficeJet 200 series using a Wi - Fi Direct connection not wireless. The problem is that whenever we turn the printer off or go to sleep Surface pro cannot re esatablish of connection with the printer again after on. In the device and printers OfficeJet 200 is still there but greyed out and has a status to be offline even if the printer has been for a while.

  The only way to connect it must make the entire process of reconnection to the Wi - Fi direct connection, for example by typing in the code and wait to see the device is connected. It should not this printer to establish a connection with the surface pro automatically after power on, yet the pro Surface shows that the printer is offline and I know that I had direct Wi - Fi together to establish the connection automatically. Is there a solution for this.

  The problem only occurs when the printer stops and he must turn it off to save battery because what get out us them for field work.

  We discovered that the Wi - Fi Direct is not fully supported in Windows 10. The only way you can reconnect to Wi - Fi direct is if you connect to the printer that you connect to an access point Wi - Fi. If you do this your Wi - Fi direct printer connection will be reset. The downside is that your Surface Pro 3 will lose the internet connection.

  For us, that our solution is not to use Wi - Fi direct and use the Wi - Fi function. We connected the mobile series HP OfficeJet 200 to our iPhone hot spot and we also connected the Surface Pro iPhone hotspot. Whenever we connect our tablet to the hotspot, we can use the printer because the printer is always connected to the HotSpot.

• 1st generation ATV dead. Orange light but no screen and no resetting of distance.  I tried direct connection to Mac and iTunes open and he's not here.  Is it possible to restore to the factory without screen or remote work

  1st generation Apple TV is dead. Orange light but no screen and no resetting of distance. I tried direct connection to Mac and iTunes open and he's not here. Is it possible to restore to the factory without screen or remote workin

  I guess you tried maintained low men together for about 6 seconds - silver 1 ATV that will restart to the diagnostic partition but who would rely on the hard disk is functional and if it was ok that wouldn't work with the logic board failure.

  I guess you have not fed and attempted to restart.

  In case your AppleTV think it is paired with another remote try Menu and left arrow for 6 seconds - the light now intervenes when you press the buttons on the remote?

  Also, it could be in the video mode bad - try Menu and upward arrow together for 6 CES switch video modes, but implies that he actually started OK.

• H710 Bluetooth and Direct Connect?

  My H710 Bluetooth works with the direct connection on my Motorola i880 phone feature?

  It is correct. Audio in and out will work with any Bluetooth headset device and an iDEN device. However the PTT function must be done with the actual combined PTT during the use of these BT headsets. There's not a BT headset device I know for iDEN combined allowing PTT of the helmet apparatus itself.

  Captive headphones (corded) allow you to control PTT of the cord.

• Admiral: Unable to remap button Direct Connect

  Hey there!

  I am unable to remap my Direct Connect button for an app or something like the calendar. When I go to the menu > settings > applications > Quick Launch, I have no option to remap the side button, all I see are shortcuts for the letters a - z. Am I the only one having this problem = D?

  If you have active with Sprint DC you won't be able to remap the DC button on the side, because you will need to use the option of DC.

  If you do not DC active with Sprint you 'll be able to remap the DC button on the side that you wouldn't be able to use it to DC and are able to remap it to something more useful.

  For the DC remapping button when the domain controller is not active on your Admiral goto: settings-> Applications-> quick launch.

  Thank you

  J

• Direct Connect with GPS or other active data

  I'm testing the possibility of using the functionality of direct connection to and from a phone while accessing other critical mission for my work tasks. We require the use of a tracking application that captures and sends GPS coordinates to a server via a data connection and also to connect to work through tasks via a web browser application. Direct connection cannot be launched on the phone while the user has any running application that uses data, it seems. It will work when the tracking application is closed and that the browser is slow and not loading pages, but doesn't if the browser will load a new page, the GPS application is running or even just Google maps. Can you get it someone please let me know if the i1 should be able to use Direct Connect when using other services that use data? I have been informed by Sprint that it is possible (two other applications can run on the data at the same time). The phone lacks a voice, only data plan.

  No, you can't. If something is using data on an iDEN connection, that's all. That's all it will do. It's just the nature of identity. If you want a phone that will have voice and data communications at the same time, you need to use CDMA or GSM.

• Update Windows using the two direct connection to proxy nd

  Use the two nd direct net connection by proxy, more time via proxy, is there a way I can configure update without changing the settings?

  am on windows 7 Home premium

  Please correct me if wrong, using "netsh winhttp import proxy IE" it says you can update via proxy, passing 'autamatically detected settings' proxy servers, will be here all the problems and errors in its conclusion/search for updates (does not search for updates error codeWindowsUpdate_80072EE2""WindowsUpdate_dt000")?

  Asked me to do this update of proxy (windows security essentials)

  The open command prompt window. [In Vista and Windows 7 you need to open the prompt as Administrator]

  2. type of this syntax: NETSH WINHTTP PROXY DEFINED (Insert here the number and proxy server) and press ENTER.

  Example: NETSH WINHTTP SET PROXY 1.1.1.1:8080
                         OR: NETSH WINHTTP SET MYPROXY .NET PROXY: 8080

  If his point is it normal that windows update as well as the WSE update fails with direct connection?

  happened with me with error msg error codeWindowsUpdate_80072EE2""WindowsUpdate_dt000"

  If the details of my proxy are 192.168.0.1 port 3128, which is the entrance to the command line...

  I had to reset the connection parameters using winhttp reset to retrieve the update in direct connection to the network

  Please give me a good solution with this

  Help us help you: start by reading this post 'sticky '...

  What information to post in the Windows Update forum
  http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/1467f44b-ee27-4F7D-98d7-f1c4b35b3395

  =======================

  You can encounter errors related to connect temporary [e.g. 0x80072EFF 0x80072EFE 0x80072EFD; 0x80072EEF; 0x80072ee20x80072EE7; 0xC80003FA 0X8024402F] when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  How to reset the Windows Update components?
  -Online skip the section to APPLY to if Win7; Access KB971058 via Internet Explorer (32-bit) only. Run the difficulty in DEFAULT and AGGRESSIVE modes, then restart [1]
  http://support.Microsoft.com/kb/971058

  ~~~~~~~~~~~~~~~~~~~~~~
  [1] full Disclosure: the difficulty operating in AGGRESSIVE mode will remove your update history but not list the updates installed in Add/Remove Programs (Windows XP) or updates installed (Vista & Win7).

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• is it possible to establish a direct connection between two computers, one running on windows xp sp2 and other running on windows xp sp3?

  Hello
  I connected two computers, one running on windows xp sp2 and others running on windows xp sp3 via com using RS232 port via link Modem DFM-562E ++.
  I am able to dial numbers from a PC successfully.
  But when I do a direct link between them (one as a host, the other guest) through the com port, I get error 777.
  Is this because the two PC's using different service packs?
  Help, please.
  Thank you & best regards
  Ravi

  It is not the service pack - although you should have installed sp3 now.

  Your message is not clear: have you been able to connect successfully computers using your modem D-Link?  How did you do that?  Will there be a modem in the second computer?

  What cable are you using to establish a direct connection between the com ports on both computers?  If you have purchased this cable online, please provide a link to the site where you bought it.

  Please describe the physical connection between the two computers.  For example, this is how you connect to the Internet by dial-up services:

  computer 1-{(9 broches) RS-232 serial port}-{RS-232 cable supplied with the modem}-{modem}-{phone cord (RJ-11 modular plugs at each end)}-{telephone wall jack}

• LaserJet 2100 direct connect network assistance

  Hello techies.  I need help please.

  I have a HP Laserjet 2100 printer with a Jetdirect 600n (J3110A) card I am using with my plug for laptop Compaq V2615US as a direct connection.  It is without a server between the computer and the printer.

  Has been fighting for more than a week. Time for me to reach and ask for help.

  It is not recognized.

  Print a page of Cofiguration Jetdirect info I get the following information:

  LAN HW address: 001083F3A247

  External Loopback 03 error is NOT READY i/o card

  TCP/IP STATUS: 55 CURRENT BOOTP/DHCP

  HOST NAME: NPIF3A247

  IP address: 0.0.0.0

  IPX/SPX STAUUS: impossible to 29 net number of senses

  NAME OF THE NŒUD: NPIF3A247

  I was able to CLEAR the error of closure by doing a loopback plug.

  Using the network printer wizard I tried individually enter either the host name, IP address, LAN HW or name of the node above the address in the appropriate box.  NONE of them worked.

  Somewhere, I saw a reference to a supposed "default" IP address of the 192.0.0.192.  Tried it as an IP address, nothing helps. Received a message on the screen indicating that it was a 'default' address and suggesting that it was not fair.

  My computer's network card is a Realtek 8139/810 x Family card that is declared as working correctly by my computer and has already been used in the past in this way with a different printer.

  Key questions are:

  1 what I'm missing or doing wrong?

  2 - is a dead Jetdirect card?

  I can access a Jetdirect 620n card, but the application list I've seen doesn't have the list of the 2100 as a printer there.

  It would be worth to try myself to a substitution of the 620n for my 600n card?

  Thanks in advance for your help.

  John

  "LittleJohn1969" wrote in message News: * e-mail address is removed from the privacy * .com...

  Hello techies.  I need help please.

  I have a HP Laserjet 2100 printer with a Jetdirect 600n (J3110A) card I am using with my plug for laptop Compaq V2615US as a direct connection.  It is without a server between the computer and the printer.

  Has been fighting for more than a week. Time for me to reach and ask for help.

  It is not recognized.

  Print a page of Cofiguration Jetdirect info I get the following information:

  LAN HW address: 001083F3A247

  External Loopback 03 error is NOT READY i/o card

  TCP/IP STATUS: 55 CURRENT BOOTP/DHCP

  HOST NAME: NPIF3A247

  IP address: 0.0.0.0

  IPX/SPX STAUUS: impossible to 29 net number of senses

  NAME OF THE NŒUD: NPIF3A247

  I was able to CLEAR the error of closure by doing a loopback plug.

  Using the network printer wizard I tried individually enter either the host name, IP address, LAN HW or name of the node above the address in the appropriate box.  NONE of them worked.

  Somewhere, I saw a reference to a supposed "default" IP address of the 192.0.0.192.  Tried it as an IP address, nothing helps. Received a message on the screen indicating that it was a 'default' address and suggesting that it was not fair.

  My computer's network card is a Realtek 8139/810 x Family card that is declared as working correctly by my computer and has already been used in the past in this way with a different printer.

  Key questions are:

  1 what I'm missing or doing wrong?

  2 - is a dead Jetdirect card?

  I can access a Jetdirect 620n card, but the application list I've seen doesn't have the list of the 2100 as a printer there.

  It would be worth to try myself to a substitution of the 620n for my 600n card?

  Thanks in advance for your help.

  John

  Without any kind of switch between the printer and the computer, you absolutely have a cable modem Simulator for your connection "ethernet".  You will NOT be able to use a standard ethernet cable.
   
  Once you find this crossover cable and that you ran a test on the printer print to the default IP address (read the printer or jet direct instructions on the card to print or otherwise find the Jetdirect card settings) then you can create a new "printer port" using the IP address of the card direct jet to join the two.    192.0.0.192 isn't usually an IP address by any device (I've never seen anywhere.)  It would more likely be something like 192.168.1.xxx.
   
  Also, you should be able to buy a switch 4 ports and do the same thing with standard ethernet cables.  Plug the computer and jet direct card printer on the switch.

• Discover device directly connected to the cisco ASA

  How do I know which is directly connected to an ASA interface? I'm looking for some commands that can be executed on the SAA to find the directly connected Cisco device.

  Thank you

  Boudou

  Unfortunately it is not available on SAA for you tell what device is directly connected to it, there is no 'see the neighboring cdp' on SAA unfortunately.

  You can check the ARP table and see which is the next hop, but who would only give the layer 3 device, such that there could be a switch between the two institutions.

• PlayBook storage and connectivity options

  I had a few qns on storage and connectivity options:

  1 - is anyone know how to 16 GB (32 GB) would be really available to the end user? In other words the quantity memory is used by the operating system, preload and how much is free for the user downloaded applications?

  2 PB seems to have sdcard support... at least that have USB host capabilities so I can reach the key USB etc?

  3. I've heard tethering via another Blackberry is possible via the bluetooth connection. It will also support tethering with a non-Blackberry phone or which is a proprietary protocol?

  4 has a GPS? I have not heard of anyone who... If this is not the case, how to use a location based service?

  tags07 wrote:

  1 - is anyone know how to 16 GB (32 GB) would be really available to the end user? In other words the quantity memory is used by the operating system, preload and how much is free for the user downloaded applications?

  2 PB seems to have sdcard support... at least that have USB host capabilities so I can reach the key USB etc?

  3. I've heard tethering via another Blackberry is possible via the bluetooth connection. It will also support tethering with a non-Blackberry phone or which is a proprietary protocol?

  4 has a GPS? I have not heard of anyone who... If this is not the case, how to use a location based service?

  1. nobody said.  You could probably guess, after understand how the BONE back in the Simulator, as well as an estimate of 'normal' size app time 10-20 that apps could be preloaded.  I hope that you will be able to remove some of the preinstalled too stuff.

  2. it is extremely unlikely that the original will have the capacity to any host, as they more or less indicated that it will act as a slave only, at the beginning.  Later, they suggested that it is actually USB OTG (On The Go) that would use as a host, but on the only clue that Lazaridis, has been saying that they have the ability (read "could, if never set free us") to support Ethernet-over-USB.

  3. jump who

  4. I guess no..  One positive aspect of the statements on the issue have been in the 5th webcast, but I still think that they have kept their options open and these statements are not official.  Because they are good in the production of material and still did not mention of the GPS in the marketing of the statements or plug in anywhere, I tend to think that he has been left out.  Saddens me... but at least this way I'll be pleasantly surprised if it stops there, rather disappointed.  I'm pretty sure that they have a task they could put a GPS module, so maybe that will be in a later model but not the first... just a guess on my part.

• Internet does not connect unless it is directly connected to the computer

  This problem occurred yesterday.

  Internet has suddenly stopped working. Things were going to turn power off, then on and distributed. I did check the lights on the modem and the router, but they were all working well. I have plugged on both computers. This does not solve it. I called Charter to see if there was a failure. Unfortunately, it's a message auto troubleshooting which I have materialized with. He had me hang my modem directly to my computer. This solved my problems of the internet.

  I went to sleep for the night in the hope that the internet, or what the question was, would fix itself. He did not. The internet still works only if it is directly connected to the computer.

  There are other people who need to use the internet here. (Invoices, work schedules and other) So maybe it's very much a problem. Any other computer or phone, will work in the House.

  What is a router problem or a cable, or...?

  If your connection works when you plug the modem but not through the router, this indicates a problem with the router.   This could be a hardware failure or a configuration problem.  A problem with the cable between the modem and the WAN port on the router is possible, but unlikely.  It wouldn't hurt to check if she.  Most routers have a reset button recessed.  I suggest that you reset the router and reinstall as if new.  If this fails, you probably need to replace the router.

  Depending on your technical knowledge, you can also log in to the router and check the status information.