Admiral: Unable to remap button Direct Connect

Similar Questions

• 1st generation ATV dead. Orange light but no screen and no resetting of distance.  I tried direct connection to Mac and iTunes open and he's not here.  Is it possible to restore to the factory without screen or remote work

  1st generation Apple TV is dead. Orange light but no screen and no resetting of distance. I tried direct connection to Mac and iTunes open and he's not here. Is it possible to restore to the factory without screen or remote workin

  I guess you tried maintained low men together for about 6 seconds - silver 1 ATV that will restart to the diagnostic partition but who would rely on the hard disk is functional and if it was ok that wouldn't work with the logic board failure.

  I guess you have not fed and attempted to restart.

  In case your AppleTV think it is paired with another remote try Menu and left arrow for 6 seconds - the light now intervenes when you press the buttons on the remote?

  Also, it could be in the video mode bad - try Menu and upward arrow together for 6 CES switch video modes, but implies that he actually started OK.

• Internet does not connect unless it is directly connected to the computer

  This problem occurred yesterday.

  Internet has suddenly stopped working. Things were going to turn power off, then on and distributed. I did check the lights on the modem and the router, but they were all working well. I have plugged on both computers. This does not solve it. I called Charter to see if there was a failure. Unfortunately, it's a message auto troubleshooting which I have materialized with. He had me hang my modem directly to my computer. This solved my problems of the internet.

  I went to sleep for the night in the hope that the internet, or what the question was, would fix itself. He did not. The internet still works only if it is directly connected to the computer.

  There are other people who need to use the internet here. (Invoices, work schedules and other) So maybe it's very much a problem. Any other computer or phone, will work in the House.

  What is a router problem or a cable, or...?

  If your connection works when you plug the modem but not through the router, this indicates a problem with the router.   This could be a hardware failure or a configuration problem.  A problem with the cable between the modem and the WAN port on the router is possible, but unlikely.  It wouldn't hurt to check if she.  Most routers have a reset button recessed.  I suggest that you reset the router and reinstall as if new.  If this fails, you probably need to replace the router.

  Depending on your technical knowledge, you can also log in to the router and check the status information.

• Smartphones from blackBerry 8350i direct connection settings

  Is it possible to directly set the connection settings to vibrate all the time.  I can set alerts to vibrate, but I can't figure out how to keep my private conversations.  When the profile is set to vibrate all the direct connect notification and appeal are private.  I want to this definition, even when the phone is set to normal.  Thank you

  Yes you can.  Or you can change the "Normal" profile or create one specifically for these parameters.  Here are the steps to not (I'll edit the profile Normal here):

  -Click the "profiles".

  -Scroll down and select "Advanced".

  -Scroll down to the "Normal" profile and press the [MENU] key

  -Select 'change '.

  -Highlight and select "Direct Connect call signal" and both the "of...". ' and ' in a case: "settings on"vibrate ".

  -Press the [ESC] key, and then choose 'save '.

  -Highlight and select "Direct Connect/GC" and again to define the parameters of "Case."... "to"vibrate ".

  -Press [ESC], then "Save".

  -Even once, press [ESC], then "Save".

  -Keep pressing [ESC] until you reach the screen saver / menu home

  -Press the button [SEND]

  -Press the [MENU] key

  -Do scroll down to 'Options' and select

  -Made scroll to "Direct Connect" and select

  -Define the scope of "Speaker" to "Off".

  -Press [ESC] and "Save".

  -Keep pressing [ESC] until you reach the screen saver

  On the right of screen saver next to the icon of your active profile at the top, there should be an icon showing the President of DC is off, indicating that all DC calls will play to the listener.

• Direct connection VMAgent: black / activity of the Client - logs show authentication error - please help

  If anyone has experience with this, I would appreciate the help.  I have tried everything I can find for three days, and it still does not.  I think I have a problem of local authentication on the Agent of the view.  The user is included in the Remote Desktop user group and the view group Agent direct connection to users.  There is no errors in the event logs, but there are errors in the logs VDM.  The suspect is the user 'WIN7B\user' unauthorized (non-local admin).  I can't find a solution to solve this error.  The firewall is disabled.

  Symptoms: Horizon View Client makes the initial connection logon sound, black screen, time-out.  User is logged on to the remote computer after failure of connection of Horizon view, then part of the logon process ends.

  Capture of logs on the Agent computer:

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (04DC-0E10) < MessageFrameWorkDispatch > [MessageFrameWork] added worker MessageFrameWork, Name = PCoIPVChan-APP (3608), Description = PCoIPVChan, channel = 0000000003F0E960

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (0E18-0A3C) < 2620 > [TPAutoConnect] pcoip_vchan_plugin_app_init2(): loan on the session 1

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (04DC - 0 C 84) < MessageChannel ReceiveThread > [MessageFrameWork] 'WIN7B\user' unauthorized (non-local admin) user, tail = PCoIPVChan-SVR (1) tip = MESSAGE_IPC

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (04DC - 0 C 84) < MessageChannel ReceiveThread > [MessageFrameWork] 'WIN7B\user' unauthorized (non-local admin) user, tail = PCoIPVChan-SVR (1) tip = MESSAGE_IPC

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (04DC - 0 C 84) < MessageChannel ReceiveThread > [MessageFrameWork] 'WIN7B\user' unauthorized (non-local admin) user, tail = PCoIPVChan-SVR (1) tip = MESSAGE_IPC

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (0E18 - 110 C) < VChanConnectionMonitor > [TPAutoConnect] VChanConnectionMonitor(): failed to get the ID of process PCoIP (err = IPC_ERROR)

  2015-12 - T 11, 14: 21:16.102 - 06:00 DEBUG (04DC - 0 C 84) < MessageChannel ReceiveThread > [MessageFrameWork] 'WIN7B\user' unauthorized (non-local admin) user, tail = PCoIPVChan-SVR (1) tip = MESSAGE_IPC

  What works:

  RDP by Horizon View Client and RDP Windows Client connections.

  Installed on the server:

  ESXi 6.0

  Windows 7 64 bit

  And the following VMWare products:

  

  Installed on the Client:

  Office Window 8.1

  

  What I'm trying to demonstrate:

  

  Portscan on Agent computer:

  PORT	STATE SERVICE

  135/tcp open msrpc

  139/tcp open netbios-ssn

  443/tcp open https

  445/tcp open microsoft-ds

  554/tcp open rtsp

  2869/tcp open icslap

  3389/tcp open ms-wbt-server

  4000/tcp open remoteanything

  5357/tcp open wsdapi

  9427/tcp open unknown

  10243/tcp open unknown

  22443/tcp open unknown

  32111/tcp open unknown

  MAC address: 00: 0C: 29:92:C9:CF (VMware)

  The full debug log file is attached.

  It certainly works in other environments, so it must be something to do with your specific configuration.

  I know that in the beginning, it has not been enough video RAM configured and certainly causes a PCoIP black screen.

  2015-12 - 10T 14: 29:07.819 - 06:00 INFO (1074-041 C) [wsnm_xmlapi] video driver name = VMware SVGA 3D

  2015-12 - 10T 14: 29:07.819 - 06:00 INFO (1074-041 C) [wsnm_xmlapi] Version of the video driver = 8.15.1.32

  2015-12 - 10T 14: 29:07.819 - 06:00 INFO (1074-041 C) [wsnm_xmlapi] video = 8 MB RAM

  It seems that this problem has been corrected, because later we see:

  2015-12 - 10T 14: 56:55.626 - 06:00 INFO (04DC - 09C 4) [wsnm_xmlapi] video = 128 MB RAM

  I also see that the modified host name:

  2015-12 - 10T 15: 03:27.050 - 06:00 WARN (04 B 0-0858) [wsnm_xmlapi] default SSL server certificate is not for this host name. The name may have changed.

  VADC itself automatically corrects the server SSL certificate, but maybe it's the other parts of the Agent posed problems that we see:

  2015-12 - 11T 09: 16:15.351 - 06:00 WARN (04EC-0CB4) authentication ticket error [MessageFrameWork]

  2015-12 - 11T 09: 16:15.351 - 06:00 WARN (04EC-0CB4) [MessageFrameWork] unable to accept the connection, authentication failed

  This does not refer to the authentication of the user customer Horizon (which is successful). This authentication is internal within the messaging system.

  Given previous problems with this Setup, I can only suggest you uninstall VADC and Agent, restart, and then reinstall the Agent and the VADC. Don't change video RAM or change the name of host/computer name.

  Let us know if that fixes it.

• View internal, external direct connection in the tunnel?

  Today we use XP virtual machines with view 4.0.1 only internal direct connect (need this to our Sun's rays). But now, we want to use our XP virtual machines to internal direct connect and externally by tunnel via the SSL protocol. What do we have to do for that?

  My idea is to install a server security in the demilitarized zone and a new second login view without direct connect server, is the right way?

  If so, we can allow the same VM XP for internal and external direct connection in tunnel?

  That's how we have our configuration of the environment.  You can configure the type of connection to the server by going to the page view Admin, configuration, servers.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• "Direct connection to the desktop" and external clients

  Hi all

  I'm doing a View 4 u1 installation with a connection to the server and a security server. I just want to confirm with the setting to view administrator, check box "direct connection on the desktop.

  I find that if I check it, then external clients of internet do not work - can see the office pools, but at launch, the customer will see appear in the taskbar, disappear. When I uncheck, all external clients work very well.

  my understanding is that this check box determines whether RDP traffic will be dug by the connection to the server or it will go straigh from the clients to view offices. I though that this setting affects only internal clients. I don't see how it affects external clients that connect through the Security server.

  When you look at 'netstat' of external clients, trying to run the office, I can see the threshold to appear when the customer view disappears, it will also disappear. Looks like when the box is check (direct connection), the client view external attempts to establish the RDP directly on desktop computers, apparently, it won't work. So, how can a direct connection for internal clients only?

  TCP 192.168.20.2:56473 winxp - 04:ms - wbt-Server SYN_SENT

  any ideas?

  Thank you

  Ming

  In our environment, we have our external users (Security Server) use a broker who has direct connect disabled while internal users use a different set of brokers that are defined to use direct connect.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Direct connection on the desktop - clients still losing access when the server goes down or rebooted service

  I set up the connection to the server with a link Direct is TICKING, I did that once the initial connection has been made for the broker and an assigned desktop computer, connect directly to the desktop and so not care about the State of the connection to the server. After restart or just restart the VMware View Server service all customers lost access until it is facing up.

  Is it right, that we use View 3.1.

  Thank you

  It's strange that I can restart my server connection without worrying about all the users.   How brokers connection you have and do you have activated all at direct connection?

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Where is the check box "Direct connection" to the pool passed in View 4

  Hi all

  I don't seem to be able to find the box of "Direct connection" who was there on view 3, in order to allow desktop computers once they have made the initial connection to the broker, for you to connect directly to the office. This has been deleted?

  I can see the "direct connection to workstations in offline mode" which is a global setting, but not one for standard pools.

  Any help / pointers greatly appreciated.

  Thank you

  Dan

  No, it has not been deleted.  It is available on a per server in the configuration on the screen from view admin tab basis.  Once in a configuration just click on servers, select the server you want to change the direct connect and change this server.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• See Security Server and direct connection

  I have a security server for my connections from the Internet. It works very well, accept when I activate "direct connection on the desktop. I found the following statement on this:

  If you bypass the secure connection, the client must establish a direct communication of RDP to the virtual machine desktop RDP (port 3389).

  That means I have to open 3389 (RDP) to the Internet if I want to use direct connections?

  If I disable the direct connections to get my security server doesn't work, I have to turn off on my login server. It is I understand that this means that if I reboot my connection to the server, all disconnected mode clients. Is there a way I can disable "Direct connections" to the Security Server, allowing access from the LAN?

  TIA.

  For a long time I had to face the problem then I hope I'm he transmit correctly.   Because you don't want to open 3389 to the internet, you must use indirect connections to the broker for users of security server connections.   This means that all connections made outside the LAN will be handled by the Security server.   If you need to restart the Security server that these connections were removed.   If you need to restart the broker to connect to security services server should not drop all connections, the external web page would become unavailable unless you also have internal customers using this broker for connections to how it would be mandated by the broker for connections and would be deleted.

  Simple solution is to have a dedicated connection, broker for the Security server that is configured in indirect mode and then have one or two brokers connection for internal users who are configured in direct connection mode.   As I have said for a long time I had to deal with this so please forgive me if I have nothing hidden.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

• Unable to get airplay to connect to my receiver to my PC.

  Unable to get airplay to connect to my receiver.

  Are both the iOS device and Apple TV on the same wireless network?

  All devices receive their network via DHCP configuration?

  Is insulation wireless disabled on the router, at least for the channel that these devices use?

  Have you tried to reboot all devices including the router first?

  TT2

• HP OfficeJet 200 series Mobile: 3 Surface Pro WIndows 10 - can't re eastablish wi - fi direct connection

  Hello

  We managed to connect our Surface Pro 3 Windows 10 running on a mobile printers HP OfficeJet 200 series using a Wi - Fi Direct connection not wireless. The problem is that whenever we turn the printer off or go to sleep Surface pro cannot re esatablish of connection with the printer again after on. In the device and printers OfficeJet 200 is still there but greyed out and has a status to be offline even if the printer has been for a while.

  The only way to connect it must make the entire process of reconnection to the Wi - Fi direct connection, for example by typing in the code and wait to see the device is connected. It should not this printer to establish a connection with the surface pro automatically after power on, yet the pro Surface shows that the printer is offline and I know that I had direct Wi - Fi together to establish the connection automatically. Is there a solution for this.

  The problem only occurs when the printer stops and he must turn it off to save battery because what get out us them for field work.

  We discovered that the Wi - Fi Direct is not fully supported in Windows 10. The only way you can reconnect to Wi - Fi direct is if you connect to the printer that you connect to an access point Wi - Fi. If you do this your Wi - Fi direct printer connection will be reset. The downside is that your Surface Pro 3 will lose the internet connection.

  For us, that our solution is not to use Wi - Fi direct and use the Wi - Fi function. We connected the mobile series HP OfficeJet 200 to our iPhone hot spot and we also connected the Surface Pro iPhone hotspot. Whenever we connect our tablet to the hotspot, we can use the printer because the printer is always connected to the HotSpot.

• Safari is unable to establish a secure connection

  More get, "Cannot open page" in Safari "...". because Safari is unable to establish a secure connection... ' Just happened with a page on the site of the City Government. All I can do to fix this. MBP3, 1, OS X 10.8.5, Safari 6.2.8

  Is the time within 5 minutes or less than the exact time? Otherwise, no secure connections.

• Hi, I am unable to see button bookmarks organized in my bookmarks menu, I need to export my favorites to HTML, could you help please?

  I want to export bookmarks o, I am unable to see button bookmarks organized in my favorites from the dropdown menu, no idea how to export bookmarks to HTML?

  The menu item bookmarks organize has been renamed to display all bookmarks in Firefox 4.0 versions +.

• H710 Bluetooth and Direct Connect?

  My H710 Bluetooth works with the direct connection on my Motorola i880 phone feature?

  It is correct. Audio in and out will work with any Bluetooth headset device and an iDEN device. However the PTT function must be done with the actual combined PTT during the use of these BT headsets. There's not a BT headset device I know for iDEN combined allowing PTT of the helmet apparatus itself.

  Captive headphones (corded) allow you to control PTT of the cord.