Folder "devices OR-imaqdx" not appearing is not in the NOT-MAX/USB cameras not recognized

Similar Questions

• HL-DT-ST DVDRAM GSA - T40N ATA Device Driver is not recognized

  Hi, I have an Acer Aspire 5920 and the HL-DT-ST DVDRAM GSA-T40N ATA device driver is not recognized.  I've uninstalled and restarted, without success.  I don't want to pay for a product fix cela, but can't find anything that I have confidence on the net - can anyone help please?

  Hello

  Try this:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/kb/982116

  See also: http://support.microsoft.com/kb/929461

• Sony Walkman device is suddenly not recognized in Windows 7

  Windows 7 has stopped recognizing my Sony Walkman NWZ - E438F Media Player since the last update. Do you have a system restore, and it did not help. Restored the walkman to the factory settings, and that did not help either.

  The walkman works fine on another computer. I tried all my usb ports - and ports all work with other devices, but do not recognize that there is an external device connected, when I try the walkman. I get power from the usb connection, however.

  Hello

  Download and install the latest firmware for your drive and check if this solves the software.

  See this link:
  http://eSupport.Sony.com/CA/Perl/support-info.pl?info_id=569&MDL=NWZE438F

  Also, download the latest version of the software from the below link:
  http://eSupport.Sony.com/CA/Perl/SWU-list.pl?MDL=NWZE438F&SelectOS=44

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• Gamepad Xbox 360 as seen in "Device Manager", but not recognized as "Game controller" and will not be installed all the drivers

  My problem is very similar to the one raised here:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_other-gaming/Xbox-360-controller-seen-in-Device-Manager-but-not/fcf52151-604e-4BF3-BF55-2fa4930bc415
  However, the OP in this question unfortunately never had answer to his question.
  When I plug my Xbox 360 controller on my laptop, my computer recognizes it as a device, but does not recognize it as a game controller. Instead, my device is listed under a category called "Other devices", and the drivers are not installed (he gets the little warning sign yellow after the icon).
  I tried to install the correct 'Microsoft Xbox 360 accessories' (http://www.microsoft.com/hardware/en-us/d/xbox-360-controller-for-windows (Windows 7 64-bit)) and direct the machine to install its drivers from there, but nothing helps.
  I've tried right-clicking on the device, by clicking 'Uninstall', out in him plugging, uninstalling and reinstalling Microsoft Xbox 360 accessories, restarted my computer and each unique combination of these things.
  I tried to talk to an Ambassador of Microsoft, who told me to update the driver and manually make a 'human interaction device', but unfortunately it did not work.
  I called Support of Windows games, who gave me information from these links:
  support.Microsoft.com/kb/908888
  support.Microsoft.com/kb/906347
  Outside of download the drivers manually in the form of 'Microsoft Xbox 360 accessories' (which I already have), I wasn't able to try all of the hotfixes listed in the guides, because my camera is not listed as a joypad or human interface device. It is simply listed as "Xbox 360 Joypad" and it is listed under the heading "other devices."
  It seems that there is just something wrong with my USB and it's just is not installing drivers properly, but this isn't the case. I plugged many other devices, including an iPod, a mouse and an external HARD drive, which all had their drivers properly installed and works great.
  I also know that it is not a problem with the xbox controller, that I plugged into another laptop (also Windows 7 64-bit), as well as pilots very well on the other laptop.
  I'm really puzzled by this situation. Any help would be greatly appreciated, but please do not repeat the information or links I listed here, or who was in the last question which I quoted above. Thank you for your help.

  UPDATE: I finally got to work. Everything is beautifully detailed in this video from Youtube:

  http://www.YouTube.com/watch?v=kxa5CJsDzwQ
  Here's what you do:
  1. plug your device and go to Device Manager
  2 right click on everything that your computer recognizes your device as (for me, it was listed under 'Other devices' and had a yellow warning sign on this subject) and click on "Uninstall".
  3. disconnect your device
  4. If you have not already done so, download and install the appropriate for your device 'Microsoft Xbox 360 accessories' program
  5. plug your device back on and go back to Device Manager
  6 right-click on everything that your computer recognizes your device as (for me, it was listed under 'Other devices' and had a yellow warning sign on this subject), but this time click on "update driver software".
  7. click on "browse computer driver software.
  8. click on "Let Me pick from a list of drivers for devices on my computer.
  9. Select "Microsoft Common Controller" and then select your device. Have it install this driver. From there on, it should work on.
  If you have any questions, my email is * address email is removed from the privacy *.

• gamepad Xbox 360 as seen in "Device Manager", but not recognized as "game controller": does not work in the game

  I connected my xbox 360 controller to my pc with the usb cable and downloaded the driver (I run XP Pro 32).  His does not work in-game.  I can see the controller in Device Manager (under the new group called xbox 360 devices) but it does not appear under "game controllers" in the control panel.  Im trying to use it with the Flight Simulator x.

  Hi Absolutemar,

  Welcome to the Microsoft Answers Community Forum site!

  In order to resolve your problem, please visit the below mentioned link.

  http://www.xbox360forum.com/Forum/

  Please perform the following steps also suggests:

  First we suggest you to download the Xbox 360 controller from the below mentioned link:

  http://www.Microsoft.com/hardware/gaming/ProductDetails.aspx

  Then install the Xbox 360 on your computer:

  Note You must install the software on your computer before you connect the gamepad Xbox 360 for Windows on your computer.

  To install the software, follow these steps:

  1. open the software that you downloaded from the Microsoft Windows gaming website or insert the Xbox 360 Controller for Windows installation disc in your computer's DVD or CD drive.

  If the screen does not appear automatically, click Start, click run, type the following command in the Open box and then click OK:

  DriveLetter : Setup

  For example, if the CD-ROM or DVD drive is drive E, type type, and then click OK.

  2. on the configuration screen, click install.

  3. follow the instructions in the Installation Wizard to complete the installation.

  Note You may be prompted to restart the computer.

  For more information about the Xbox 360 installation on your computer, visit the below mentioned link:

  http://support.Microsoft.com/kb/906347

  In this case, you need more information, you can visit the link below.

  http://www.Microsoft.com/games/en-us/community/pages/forums.aspx

  I hope this helps!

  Thank you best regards &,.

  Calogero - Microsoft technical support.
  Visit our Microsoft answers feedback Forum
  http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ and tell us what you think

• USB device not recognized (Nothing plugged and the mouse does not)

  My mouse (microsoft) wireless worked well until what within hours.
  then I said to unrecognized USB device
  The port works, but for some reason any
  the mouse is not, went bought another mouse and still getting the same message.
  Plus I get the USB device not recognized pop up, same
  Tho, nothing is plugged into one of the USB ports.
  Any suggestions on how to solve this problem

  Computer brand and model?  Windows OS?

  Open the Device Manager

  Click on the + sign next to USB controllers

  Do you not see that unknown device listed?

  Right click on the playlists of USB root hub

  Select uninstall

  Close Device Manager

  Restart the computer to Windows reload the drivers

  USB is now recognized?

  If failed, shutdown computer.  Unplug it from the electrical outlet.  Leave unplugged for 1 to 2 minutes.  Plug the unit in and restart the computer.

  USB is now recognized?

  How to troubleshoot USB device problems that can occur after a laptop computer that is running Windows Vista recovery from sleep or standby extended

  http://support.Microsoft.com/kb/953367

  Windows Vista does not recognize a USB external optical disc drive when you reconnect the USB optical drive to the computer drive

  http://support.Microsoft.com/kb/944292

  Run the System File Checker

  Right-click on command prompt and select run as administrator

  Type sfc/scannow

  Press enter

  Note: there is a space between sfc and / scannow

  How to analyze the log generated by the SFC Scan file:
  http://support.Microsoft.com/kb/928228

• W7 Device Manager does not recognize the Intel AMT devices

  Please help: where can I find - how to install the latest drivers Intel AMT for Windows 7.

  Hello

  Thank you for the question to Microsoft Community. I'll give my best to help you.

  From your problem description, I understand that the Device Manager does not recognize the Intel AMT devices

  What is the brand and model of the computer?

  Check out these links and see if they help.

  Computers that use Intel's vPro technology can have devices that are not recognized in Windows 7 Device Manager

  http://support.Microsoft.com/kb/976728

  Clean installation WARNING: Back up your files before you begin reinstalling Windows, even if you're reinstalling Windows on a hard disk partition. A clean installation replaces the current version of Windows and all personal files.

  If your motherboard supports AMT technology, you can download, install the drivers from this link.

  AMT: Intel® AMT Driver for Intel® motherboards

  http://Downloadcenter.Intel.com/Detail_Desc.aspx?&DwnldID=16936

  Note: This download is valid for the products listed below.

  Intel® card mother DB43LD

  Intel® card mother DQ43AP

  Intel® card mother DQ45CB

  Intel® card mother DQ45EK

  If the problem persists, I suggest you to contact Intel support. http://communities.Intel.com/Community/Tech

• NB200 - Webcam not recognized

  Hi, hope someone can help with this!

  Webcam is not working. Under Windows XP. Does not appear in the devices in Control Panel > system > device

  For a while, I kept getting the error message "USB device not recognized" when I start the computer, and then whenever I adjusted the screen, so those who were probably related. ?:|

  Updated the driver and USB issue went, but when I try to open the Camera Assistant Software, it says "Webcam is either disabled or failed.» Please check your webcam settings. »

  (X-)

  Thoughts?

  Hello

  I recommend first load default settings in the BIOS. Save these settings, exit the BIOS and restart your laptop.

  Then, make sure that the latest driver for the Toshiba webcam is installed. You can download it on the Toshiba site.
  In addition, it would be advisable to install the latest version of the BIOS. Visit the Toshiba page!

  In the worst case if you have the same problem after reinstalling the Toshiba Recovery disk it associated material s. This means that you should contact an authorized service provider. Guys can check the mobile and exchange equipment (webcam, cable or something else). Just get in touch with the guys and ask for help. From my own experience, I can say that they always try to help you as best we can.

  Good luck! :)

• HP LaserJet P1102: USB not recognized during installation of HP LaserJet P1102

  I have a Sony Vaio VPCEH computer laptop with Windows 7 and when I run the disk I got with the printer on my laptop, that the installation procedure works in what concerns the section "Install printer Software". When you are prompted to turn on the printer and connect the cable USB to the laptop it says 'USB not recognized '.  I tried all 4 slots USB into my laptop but the USB still appears as an unknown device with an exclamation point in a yellow triangle. I searched internet solutions and tried to uninstall the unknown device in Device Manager and restart the installation with the disc, I also tried clicking on the unknown device driver software update but it says the software driver is up to date and still, it shows as an unknown device and is not recognized. I also tried to uninstall the HP software from the disc on my laptop and that reinstall but nothing has worked. I felt for over 2 weeks now and have not been able to use it because of this problem and I really need for University, so I would be very happy if someone could please give me a solution to this problem

  Hi @Janemaguire,

  Have you tried another USB cable?

  Because the printer is not detected on the Mac, it may be the USB port of the printer.

  What happened when you tried to install the printer on Mac?

  Error messages?

  What is the model Laserjet P1102w?

  Let me know. Thank you.

• pilot iPhone is not recognized by Windows 7 (64-bit) Enterprise

  When I plug my iPhone the device driver is not recognized and can not install.  The iPhone will appear as Apple Mobile Device Driver but cannot install the driver.  I can't use my iPhone as a drive hard as if I was on Windows XP.

  Usually, as with most of the iPads, iPods and iPhones, iTunes is usually required.

• PC not recognizing external hard drive

  Hello

  I have a HP Pavilion P6635UK (using windows 7 home) that I have used with an external drive WD successfully for several months.  Now, he does not appear to recognize the external hard drive.

  When I connect via USB and then go to 'Start/computer' it does not appear. If I go on "Devices and printers" it appears and indicates that the device is functioning properly. If I open "Devices and printers", it will allow me to "safely remove hardware & eject media. What gives the beep when I do. I tried to use different ports USB (the Pavilion) but the result is the same.

  He also appeared in the "Device Manager" as working properly. Using the "convenience store" it is said "Troubleshooting couldn't identify the problem." Other devices using the same all the USB ports work correctly

  I also have a Compaq Presario notebook in which the WD external HD works fine.

  Any help would be appreciated

  Cyprien

  I think I can solved this problem by myself (with a little research in the WD support forum)

  Go to start, right click on computer, select manage, select disk management. The next column on the left will show all readers with their corresponding letter. My external hard drive doesn't show any letter entrusted to him. Right-click on where the drive letter should appear and select the path and change the drive letter. Select any letter you wish to call, and then click OK.

  Now admittedly. But why it happened in the first place when he was working very well before I have no idea.

• Equium A60 - Generic not recognized USB Hub

  Equium A60, XP Home Edition SP3.

  My Tevion USB 2.0 combo card reader is reported as being a USB device fails, is not recognized and implemented in the device as an unknown device manager.

  Here's the riddle:
  When I plug it into the same old PC under XP Pro SP3, it is recognized and works.
  When I plug it into a new PC running Vista Home Premium, it is recognized and works

  And finally, and especially:
  When I plug a USB 1 Hub 4 ports on the A60 Equium and then plug the Tevion USB2.0 card reader this Tevion card is recognized and works. There are a lot of bleating like a lost sheep on the run faster if connected to a USB 2 port, but if I plug it directly into the port from Toshiba it does not at all.

  Any ideas to solve this problem or similar experiences?

  Wizzer

  Is the gap of 4-port hub powered by the USB port of your satellite or is it a KVM?

  If self-powered it s then it s obviously needs a lot of power combo card reader which can be provided by all of your computers, but not the satellite.

  It is a theory that might make sense... :)

  Welcome them

• Connected to the Portege 3500 USB DVD burner is not recognized correctly

  I am trying to connect a burner DVD HP DVDv 940th my 3500.When Portege I plug in the device, it is not recognized and the Device Manager list as a storage of unknown mass without a driver. Where can I get this driver?

  Hello

  Try to check the assumption of the manufacturer or the download page. Manufacturers of portable gift use support external devices t produced by other companies.

• Creative Sound Blaster Audigy 2 not recognized ZS running Win 7 Ultimate - 64-bit

  Friends,

  I have a situation where I ask for a help. It's as follows:

  1. the old desktop that PC is equipped with a device for Creative Sound Blaster USB based - Audigy 2 ZS attached, it was purchased in August 2008 and since then, initially worked with Win XP (32-bit) - August 2008 to Oct 2012, then Oct. 2012 (when I upgraded the operating system to Win 7 Ultimate 64 bit) until last week when I upgraded the PC hardware.

  2. However, after the upgrade, the PC does not recognize this device shows at all - a yellow exclamation mark with a label "unknown device" in Device Manager, when I connect the device to the USB port.

  3. the last time (in 2012) when I upgraded the OS on the old XP PC to Win 7 hardware, the operating system recognizes the device even without installing the drivers (i.e. for Audigy 2 ZS of Creative) and he has been active (usable), as soon as I plugged the same. However, later I applied Win 7 64 bit drivers from the Creative support site. Now, even though I applied the drivers for Win 7 64 bit for the device, it is not recognized under Windows.

  At the config of my old PC: Intel Core 2 Duo CPU E6540, card mother Intel graphics card Nvidia GT 220, some hard drives SATA 2 x 250 GB, 8 GB of RAM.

  At the config of my new PC: Intel Core i3 (3rd generation), card mother Gigabyte, graphics card Nvidia GTX 650, SATA 1 x 1 TB hard drives & 1 x 250 GB, 8 GB of RAM.

  I understand that this question, referring to the Creative device, should not fall directly under the responsibility of Microsoft, however, I looking for entries from anyone who may have any suggestions or is faced with identical situations / similar. Thanks for the patience to read this long query.

  -Milind

  BossDweebe,

  Thanks for the suggestions. The origin of difficulties - the PC also has graphics card Nvidia GTX 650 and as part of the package of drivers for this graphics card, HD Audio driver (Nvidia) also was installing. This HD audio driver not allow Creative Audigy 2 ZS on USB to be recognized as an audio device. So I had to remove the HD from Nvidia audio driver and then install (an update) Creative driver for the device. It worked.

  Thanks for your suggestions.

  -Milind

• ("My CD or DVD drive is missing or is not recognized by Windows (Code 39)")

  My CD / DVD is missing or is not recognized by Windows. My driver Version: 6.1.7601.17514, OS is windows 7.

  I received the following message:

  • Windows encountered a problem installing the software driver for your device
  • Windows raise driver software for your device but encountered an error trying to install it.
  • Windows cannot load the driver for this hardware device. The driver may be corrupted or missing. (Code 39)

  I tried several ways to follow the steps that says on the website of Microsoft, as with the help of the hardware and peripheral troubleshooting tool, but it didn't work.  I also used a new external device and was not recognized by windows as well. By the way

  Can you still collect my DVD player?  How can I solve this problem? Thank you

  Run these set the then restart.

  http://support.Microsoft.com/kb/982116

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  http://support.Microsoft.com/kb/316529/

  http://support.Microsoft.com/kb/314060