G5x - loading via the USB cord and a powerbank?

Similar Questions

• connect a laptop computer people visit to my desktop via the USB cord

  If I connect my laptop to friends to my computer via the USB cord so that she can get on the internet, if there is nothing wrong on my computer like a virus or something bad, he can go on to the laptop? And if I have a wireless router & it connects to the internet in this way, can get the same bad things in his laptop? I know that sounds pretty lame, but I don't have a laptop.

  First of all, it is doubtful that you could find a USB bridge cable to connect two computers, and even if you did, it would be difficult to configure things to enable the second computer to access the Internet.  (But see http://www.hardwaresecrets.com/article/Connecting-Two-PCs-Using-a-USB-USB-Cable/248)

  The good way to share your Internet connection is using a router (wired or wireless, any - except convenience).  But it is certainly possible for the virus to spread on a network, it is unlikely as long as each computer has an antivirus application to update and Windows Firewall (or a good third party firewall) is enabled.

  If you don't want to buy a router (and note that a router is very good for you security protection even if you only have one computer), you can connect the two computers with a cable 'cross-over' (a special type of cable Ethernet) and of XP Internet connection sharing.

  If you wish, you can disable 'file and printer sharing' on computers or both to further isolate them from each other.  Details vary for different versions of Windows.  Here's how in XP: http://compnetworking.about.com/od/windowsfilesharing/ht/enable_disable.htm

• I am running Vista Business SP2 and my machine don't allow / recognizes any device that I attached via the USB port such as card readers digital camera, IPOD, etc.

  These devices appear in Device Manager under "other devices" and I am invited to the drivers that I don't have to install. Microsoft fix it detects that there is a problem but does give some answers. I checked with device manufacturers and there is no driver available for download (supposed to be plug-and-play). This seems to be a common problem... What is the answer?

  Canon has attempted to address the problem and they came to the conclusion that it is a Vista operating system problem. I've seen several postings of similar problems - is there a solution?

  Hello

  1 did you change on your computer before this problem?

  You can follow the methods below and see if it works.

  Method 1

  You can check out the article below and see if it works very well.

  Tips for solving problems of USB devices

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Method 2

  If the problem persists, you can uninstall and reinstall the drivers of USB controllers.

  un) Click start.

  (b) in the search box type Device Manager.

  (c) go to the USB controllers and expand the chevron.

  (d) right-click and go to Properties.

  (e) select the tab drivers , and then click Uninstall

• Passport for blackBerry I can attach Blackberry passport for HP laptop using the USB cord?

  If I buy the new passport of BB I can attach by using the USB cable to the laptop HP?

  I currently have a BB Torch, and I connect via BB Desktop using my AT & T data plan to access the Internet when I'm out and about. I like to use the USB cord to attach the unit to the HP laptop. I think I get a strong signal in this way. I'm not a big fan of wifi.

  I want to buy the new passport, but if I can't attach it so I don't know if I'm ready to change devices.

  Yes it is supported, it is here in the manual

  http://BTSC.webapps.BlackBerry.com/BTSC/ViewDocument.do?noCount=true&externalID=en65987BlackBerry_Pa...

• iPhone 7 will not play audio via the USB port on the car.

  When I plug my iPhone USB port 7 more in my car (15 Jeep Grand Cherokee), the artist/song/podcast information appears on the screen, but the sound plays through the speakers of the phone.  I have confirmed that my settings are all the same as they were on my 6s, who played without any problems via the USB connection.  Bluetooth streaming works fine - no problems at all.  Any ideas, or is this a problem similar to that people have with CarPlay?

  Welcome to Apple Support communities, kevo.mac!

  Congratulations on your new iPhone 7 more! I see that you connect with your Jeep Grand Cherokee using the USB port. Everything seems to work fine, except that the music plays through the phone instead. I'll be happy to help you to get this working.

  Help to connect your iPhone, iPad or iPod touch with your car radio

  If you are using USB playback

  Restart your iOS device and your car.
  Connect your iOS device to another stereo USB port (if you have one).
  Try another USB cable.
  Update your iOS device.
  Install the updates to the firmware of your car radio.
  Test of audio playback from a different application. If you can not play audio from a specific third party application, contact the developer of the app for help.
  If you can not play audio from an app Apple, contact Apple technical support.

  Enjoy your weekend!

• Is it possible to plug a USB to my new iPad Pro, to transfer PDF files and some Jpeg files from the USB key with an adapter of lightning? If there is NO adapter, how can I get these files on the USB key and my iPad pro?

  Is it possible to plug a USB to my new iPad Pro, to transfer PDF files and some Jpeg files from the USB key with an adapter of lightning? If there is NO adapter, how can I get these files on the USB key and my iPad pro? I need these PDF files transferred my I touch pro. Any suggestions?  Please

  Thank you

  Mike Tingey

  The iPad does not support USB keys. There are some wireless flash drives that can be used, but not the classical records. I suggest you transfer files to a computer and their synchronization then back to the iPad via iTunes.

• My HP 14 laptop is not recognizing the usb ports and wifi at startup.

  During the last few days I been dealing with the issue that my laptop does not recognize the usb ports and wifi. After several reboots, it works fine. My drivers are up to date, so I don't know why, I'll have this terrible problem.

  Welcome @hildergarn,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you have a problem with your Wi - Fi and USB ports on your laptop from HP.

  My first suggestion would be to use the wireless network troubleshooting and Internet tool. At the bottom it will ask you questions to help you diagnose the problem.

  Please take a look at this great Charter called troubleshooting wireless network and Internet. This document will help you to solve the problem of Wi - Fi.

  Have you tried to restore the BIOS?

  Have you tried to connect directly to the Modem/Router?

  You have uninstalled the driver in Device Manager?

  Please try to uninstall the driver in Device Manager by using the following steps:

  • Go to the Device Manager.
  • Expand network adapters.
  • Right-click on all NICs individually.
  • Click on uninstall.
  • Restart the laptop twice.

  How many devices you try to connect?

  What you are trying to connect via USB?

  Are - what you happened to try to use the HP Support Assistant?

  Here is a link to the HP Support Assistant, if you not him have not yet tried. Simply download and run the application and it will help with the software and drivers on your system that need updated.

  Here are other troubleshooting steps that may help too. If the USB device does not appear in Device Manager, then it might be a question of power requirement. Unplug the machine and perform the following steps until the device is detected:

  • Reboot the laptop

  • Plug in and wait five seconds.

  • If the device does not appear, try connecting to another USB port.

  • If the USB device is displayed in Device Manager after you connect the cable to a different port, then uninstall and reinstall the software of USB device driver.

  If the device is not recognized in any port, unplug it and go to the next step.

  • Open the Device Manager.

  • Double-click Bus USB controllers,

  • Double-click on a USB root hub,

  • Click the Power tab

  • Click on properties of power supply (if it is displayed).

  Devices need that are connected to the hub are shown, as well as the power they have. If the total displayed power is more than 500 mA, remove the devices and use a hub powered.

  • Continue looking at the properties of the power of each USB hub. If the total power required exceeds the total available power for the hub, then remove a device on this hub to a decrease in the number of consumption.

  • Plug in and wait five seconds. If the device is not recognized, unplug and go to the next step.

  Please note; Remove USB cables at high speed that are more than 3 m (9.8 ft) in length and use cables at high speed that are shorter than 3 m.

  Source: troubleshooting USB connections - please look at this document and follow all the steps in it.

  When we came to a resolution, please share what has worked for you with others by marking this post as an acceptable Solution. If you do not want to show your appreciation for my efforts today, please take a second to click the Thumbs Up button below.

  If please re-post and let me know the detailed results of all the troubleshooting steps in this post. Could you please provide me with your model number (How can I find my model number or product number?) also.

  Can't wait to hear from you!

  Have a great day!

• PC does not recognize the ipod when I plug in the USB cord.

  I have an ipod touch, and it will replace my old ipod.  When I plug the USB cord, nothing is recognized by the computer.  It is also not recognize my old ipod when I plug it now.  I have other devices that use a USB cord, and they work as they should.

  Apple told me to check with Security Essentials to see if they are blocking a pilot... I am quite at a loss.  It's the ipod or it is safety, or is it the computer?

  I tried everything on separate computers, and they don't always work.

  Any help is appreciated!

  It is not MSE-you get a warning if it were.  Try another cable or try on another PC.  It sounds like the cable might be the problem if all of a sudden or iPod works.

• Trying to install a new installation of win xp on a dell insp 700 m. all is well until you are ready to hit enter to select where to load windows. the keyboard freezes and crashes.

  win xp install

  Im trying to install a new install of win xp on a dell insp 700 m. all is well until you are ready to hit enter to select where to load windows. the keyboard freezes and crashes. It worked early, when I hit enter to launch the cd? any ideas? TX marty

  Thank you! I tried what you mentioned, nothing has worked... I plugged a usb keyboard and it works, so I'm starting to believe it could be a motherboard problem. I finally got windows xp pro installed, no conflicts in Device Manager, all the drivers are installed and now running smooth. I removed the keyboard, and re-set, all connections look good, but still not good. the synaptics keyboard works fine and both rt & lft click the buttons. I pulled the ram to inspect it, it's the right speed, ddr2700, and after running for an hour, it was cold to the touch! I'll try to get a new keyboard and replace it, their pretty good work, if still not good it becomes pieces on ebay... lol tx again... Marty

• Photosmart 7960 installed via the USB port on the PC under Win XP Pro acting as a print server

  I have a PC running Windows XP Pro, which acts as the home network file and print server.   The Photosmart 7960 is connected to this computer via a USB cable and configured to be "shared".   When I go to "Add a printer" on another PC, in Windows 7, which is also part of the same network, I can navigate to the 7960 correct, but the installation wizard is unable to find the driver for Win 7.  I still have what in the HP see basic documents that tells me how to add this shared printer on my Win 7 PC.  Looking at the support page drivers I saw that Windows 7 already has the driver.  True, but the only way, it seems that I can get to it is to connect the printer directly to Win 7 PC via a USB cable.   Any suggestions?

  Apparently, the solution is as follows.  First connect the photosmart 7960 directly to the PC running Windows 7 via USB cable network.  It will be auto-install drivers.  Reconnect the printer to the PC under XP pro server.   From the PC running Windows 7 where you have installed the printer via USB, you can go ahead and remove the photosmart 7960 from the list of printers; This will not remove the just downloaded drivers.  Next, select Add a printer, and then select 'Add a local printer' (no network).  Select 'Create New Port' and click Next.  In the next dialog box, type the name of the host server and the name of the printer.  In my case, it's \\mainserver\HP photosmart 7960. Click Next.   In the "Install the printer driver" dialog, click "Hewlett Packard" and find the 7960 in the printer list and click Next.  I was able to successfully install the printer this way.

• Problem syncing cell to pc "when I plug the USB cord nothing happens."

  Original title: Cell synchronization to pc problems.

  I have Windows Vista and I downloaded the pantech link (p7040) pc suite to synchronize my phone to the pc and when I plug the USB cord nothing happens. The toolbar does not show that something is plugged. What should I do?

  Hello

  Thanks for choosing Microsoft Community.

  Please answer these questions:

  1. have you already tried it with different USB ports / cables?

  2 have you tried it on another computer?

  Let us try these steps and see if that helps:

   

  Method 1: Try again with different USB ports and if it recognizes the phone.

   

  Method 2: Run the following fix - it:

   

  Hardware devices do not work or are not detected in Windows:

  http://support.Microsoft.com/mats/hardware_device_problems/en-us?WA=wsignin1.0

   

  Method 2: Delete all the USB controllers and see if that helps:

  See the following steps:

   

  a. Click Start, type run, select run, type sysdm.cpl in the Open box, and then click OK.

  b. click on the Hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  f. restart the computer and wait for windows to reinstall the USB controllers.

  g. plug in the removable USB storage device and perform a test to ensure that the problem is solved.

  Hope the helps of information. If you need help, please reply. We will be happy to help you.

• When I try to connect to the internet via the usb cricket modem thing, I get an error entry ras error creat/change also error 1068

  Original title: new laptop user

  I recently got a laptop EEE. When I try to connect to the internet via the usb cricket modem thing, I get an error ras entry creat/change. I tried to set the automatic start, but when I click the button start I get an error 1068. Any help?

  Hello

  I suggest you follow the troubleshooting steps form the article and check if it helps.

  "Error 1058" error message appears when a service stops unexpectedly

  http://support.Microsoft.com/kb/241584

  Also refer to this article and check if it helps:

  "Error 1068" error message when you try to enable Internet connection sharing

  http://support.Microsoft.com/kb/827328

  Note: Also valid for Windows Vista

• Menu to transfer the photos on my memory card does not appear, is there another way I can do?... Without using the usb cord...

  Menu to transfer the photos on my memory card does not appear, is there another way I can do?... Without using the usb cord... He lost. :/

  The following steps may be worth a try:

  Insert your memory card into your Media Player...

  Reach... Start / computer...

  What is the memory card show as a drive letter? (if your Media Player)
  has several slots, there will be several "hard drives" listed... the
  SD card will be one of them)

  If_Yes_right click on the drive letter correct and in the menu... Choose...
  Open... now you should see the directory of the memory card or to explore.

  From there you should be able to drag and drop or copy and paste the
  files in a folder on your hard drive.

  Also... the following items may be worth a visit:

  Windows Vista-
  Troubleshoot AutoPlay
  http://Windows.Microsoft.com/en-us/Windows-Vista/Troubleshoot-AutoPlay-problems

  Windows Vista-
  How to change the auto run settings
  http://Windows.Microsoft.com/en-us/Windows-Vista/Change-AutoPlay-settings

  Windows Vista-
  AutoPlay: Frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows-Vista/AutoPlay-frequently-asked-questions

• How to disable the USB port and change DVD drive to read-only?

  I have upgraded my Vista Home Premium from window to window 7 Ultimatum. I tried to disable the USB port and and change the configuration of DVD room to read only via the bios, but I wasn't able to do. The bios always the same, whether it was when I had vista.

  I wonder if the operating system upgrade from Vista home premium to Windows 7 ultimate trigger necessarily upgrading the bios in order to take full advantage of the Windows 7?

  Thank you

  * original title - upgrade from Vista home premium to Windows 7 ultimate necessarily triggers upgrading the bios in order to take full advantage of window 7? *

  rThen your question isn't specific to Windows 7, you must consult the manufacturer. You should be able to disable the USB via the BIOS ports. Also, why do you want to set the optical drive as read only? If it is shared? If so, the advanced sharing disk properties, from there, you can set permissions on the drive. If you releasing It Easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• Error 17-Windows will not load past the splash screen, and system repair has no effect...

  Hi all, my problem is the following. Off my laptop the night before, an upgrade has been installed as usual. However, when I tried to start my computer the next day, I was meeting with a choice of operating systems, one was vista and one was something called "openSUSE 11.2 installer (NET).» Of course I wanted to choose vista, but when selected has been sent to a screen that read (sorry for the amount of the entry).

  Start "openSUSE 11.2 installer (NET)".

  (hd, 1)

  Specifien type is ntfs, partition type 0 x 7

  /openSUSe/ kernel linux devfs = mount, dall ramdisk_size = 65536 = ftp install: //ftp4.g wdg.de/pub/opensuse/distribution/SL-OSS-factory/inst-source/ server = ftp4.gwdg.de lang = en splash silent vga = 0x31A

  Error 17: File not found

  I don't know much about this sort of thing, so he thought better to include everything I could. At first, I tried to reload Vista, but it just opened the same screen, so found the vista disc that came with the laptop and it is stuck in. I ran sytem repair and system restore and both have had no effect.

  I'd appreciate any help is sorting this point, but if I have to reinstall vista (what I hear the hard disk wipes), is it possible to backup all my files to be reintergrated later.

  Thanks for any help!

  "Off my laptop the night before, an upgrade has been installed as usual."

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost, please include Error Codes, including what you have already posted, andexactly what happens after you tried to update.

  In this way, you will receive the best help.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner