Gateway RV320 ping RV320 VPN question
Hi all
I have 3 x RV320 with the latest firmware to all configure to use VPN from gateway to gateway in a configuration of spokes and hub.
On all RV320, I can see the connected state of the VPN tunnels. However, I can't do a ping to gateway to gateway or computer connected to each RV320. Firewall has been disabled on all RV320.
Any help will be appreciated.
concerning
J
Try the ping of the diagnosis of each rv320 page. Recreational vehicles cannot ping between them? If so, your tunnel is up, but something wrong with the subnet configs.
Tags: Cisco Support
Similar Questions
-
3 RV320 VPN with a local IP address
Hello..
I have 3 RV320 routers, I try to connect by VPN all routers together, the problem is I have a server on a single router 192.168.1.200 and I need to connect the terminals to the other routers on the internet...
any suggestion?
Connect VPN tunnels between all 3 units. Please keep in mind that subnets are different. Get close to the tunnel. Ping 192.168.1.200 at two remote sites to verify connectivity. Try the terminals.
-
RV320 VPN cannot access peripheral LAN using iPad
With the help of RV320, firmware 1.1.1.06
LAN 192.168.1.x 255.255.255.0
VPN 192.168.09.100 to 192.168.09.150
I need to access a device on the local network using this VPN connection from iPad. The Unit received address DHCP on LAN, broadcasts its presence every second on the Port 4992.
When it is on the LAN, the iPAD sees the presence of broadcasting and accesses the device without problem. When I VPN in, easy VPN works well. I configured the firewall of the router as the rules:
Allow All traffic [1] LAN 192.168.9.100 ~ 192.168.9.150 192.168.1.1 ~ 192.168.1.255 Always
Allow All traffic [1] LAN 192.168.1.1 ~ 192.168.1.255 192.168.9.100 ~ 192.168.9.150 Alway
If I first connect to the device when the iPad is on the local network, I turn off WiFi and connect through the VPN, I can continue to control the device. However, if I'm not connected to the device locally first, I see the presence broadcast on port 4992 when it connects first via the VPN. Broadcasting does not reach the iPad from a 192.168.1.x device connected 192.168.9.x.
What is the correct way for the iPad on the 192.168.9.x, see the dissemination of 192.168.1.x?
Hello
Broadcasts will not be sent on the VPN tunnel. The only traffic that will pass from the LAN to your customer's traffic specifically aimed at it, otherwise the router send him outside. Looks like your presence Pack is a show, so all VPN clients won't be able to see.
I think that when you connect locally you are picking up on the broadcast and then when you go to the VPN that has not passed yet, so why does it work if you connect locally first.
Hope that helps a little,
Christopher Ebert - Advanced Network Support Engineer
Cisco Small Business Support Center
* Please note the useful messages *.
-
I am ASA 5505 that I am of is running correctly by using the AnyConnect client. The question is, can I connect to the fine external interface, but cannot ping or attach them to any host on the inside. When I connect, it accepts the user name and password, and I can run the ASDM or SSH to the firewall very well, but not further. In the control, after I log in, I get an IP address inside, of the order of 10.7.30.x as expected.
Following configuration:
: Saved
:
ASA Version 8.2 (5)
!
asa5505 hostname
domain BLA
activate the password * encrypted
passwd * encrypted
no names!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 150
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 10.7.30.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP EXTERNAL IP 255.255.255.128
!
interface Vlan150
nameif WLAN_GUESTS
security-level 50
IP 10.7.150.1 255.255.255.0
!
boot system Disk0: / asa825 - k8.bin
config to boot Disk0: / running-config
passive FTP mode
clock timezone STD - 7
DNS server-group DefaultDNS
domain BLA
permit same-security-traffic intra-interface
object-group service tcp Webaccess
port-object eq www
EQ object of the https port
object-group network McAfee
network-object 208.65.144.0 255.255.248.0
network-object 208.81.64.0 255.255.248.0
access extensive list ip 10.7.30.0 outside_1_cryptomap allow 255.255.255.0 192.168.24.0 255.255.252.0
access extensive list ip 10.7.30.0 inside_nat0_outbound allow 255.255.255.0 192.168.24.0 255.255.252.0
access extensive list ip 10.7.30.0 inside_nat0_outbound allow 255.255.255.0 172.16.10.0 255.255.255.0
outside_access_in list extended access permit tcp any host 159.87.30.252 eq smtp
outside_access_in list extended access permit tcp any host 159.87.30.136 Webaccess object-group
outside_access_in list extended access permit tcp any host 159.87.30.243 Webaccess object-group
access-list extended outside_access_in permit tcp host 159.87.70.66 host 159.87.30.251 eq lpd
outside_access_in list extended access permit tcp any host 159.87.30.252 Webaccess object-group
outside_access_in list extended access permit tcp any host 159.87.30.245 Webaccess object-group
outside_access_in list extended access permitted tcp object-group McAfee any eq smtp
permit access list extended ip 172.16.10.0 outside_access_in 255.255.255.0 10.7.30.0 255.255.255.0
outside_access_in list extended access permit ip host 159.87.64.30 all
standard access list vpn_users_splitTunnelAcl allow 10.7.30.0 255.255.255.0
IPS_TRAFFIC of access allowed any ip an extended list
access extensive list ip 10.7.30.0 outside_nat0_outbound allow 255.255.255.0 any
inside_access_in list extended access permit udp 10.7.30.0 255.255.255.0 any eq snmp
access extensive list ip 10.7.30.0 outside_cryptomap allow 255.255.255.0 172.16.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
host of logging inside the 10.7.30.37
Debugging trace record
Within 1500 MTU
Outside 1500 MTU
MTU 1500 WLAN_GUESTS
local pool VPN_POOL 10.7.30.190 - 10.7.30.200 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-645 - 206.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 0-list of access outside_nat0_outbound
NAT (WLAN_GUESTS) 1 0.0.0.0 0.0.0.0
public static 159.87.30.251 (Interior, exterior) 10.7.30.50 netmask 255.255.255.255
public static 159.87.30.245 (Interior, exterior) 10.7.30.53 netmask 255.255.255.255
public static 159.87.30.252 (Interior, exterior) 10.7.30.30 netmask 255.255.255.255
public static 159.87.30.243 (Interior, exterior) 10.7.30.19 netmask 255.255.255.255
public static 159.87.30.136 (Interior, exterior) 10.7.30.43 netmask 255.255.255.255
Access-group inside_access_in in interface inside the control plan
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 159.87.30.254 1
Route inside 172.16.1.0 255.255.255.0 10.7.30.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server ADWM-FPS-02 nt Protocol
AAA-server ADWM-FPS-02 (inside) host 10.7.30.32
Timeout 5
auth-domain NT ADWM-FPS-02 controller
AAA-server ADWM-FPS-02 (inside) host 10.7.30.49
auth-DC NT ADWM-DC02
AAA authentication http LOCAL console
AAA authentication LOCAL telnet console
the ssh LOCAL console AAA authentication
Enable http server
http 206.169.55.66 255.255.255.255 outside
http 206.169.50.171 255.255.255.255 outside
http 10.7.30.0 255.255.255.0 inside
http 206.169.51.32 255.255.255.240 outside
http 159.87.35.84 255.255.255.255 outside
SNMP-server host within the 10.7.30.37 community * version 2 c
location of the SNMP server *.
contact SNMP Server
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
card crypto outside_map 1 match address outside_1_cryptomap
peer set card crypto outside_map 1 206.169.55.66
map outside_map 1 set of transformation-ESP-3DES-MD5 crypto
card crypto outside_map 2 match address outside_cryptomap
peer set card crypto outside_map 2 159.87.64.30
card crypto outside_map 2 game of transformation-ESP-AES-192-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
Crypto ca trustpoint *.
Terminal registration
full domain name *.
name of the object *.
MYKEY keypairs
Configure CRL
Crypto ca trustpoint A1
Terminal registration
fqdn ***************
name of the object *.
MYKEY keypairs
Configure CRL
Crypto ca trustpoint INTERMEDIARY
Terminal registration
no client-type
Configure CRL
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint0
Configure CRL
Crypto ca trustpoint ASDM_TrustPoint1
Configure CRL
ca encryption certificate chain *.
certificate ca 0301
BUNCH OF STUFF
quit smoking
A1 crypto ca certificate chain
OTHER LOTS of certificate
quit smoking
encryption ca INTERMEDIATE certificate chain
YET ANOTHER certificate
quit smoking
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca LAST BOUQUET
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet 10.7.30.0 255.255.255.0 inside
Telnet timeout 30
SSH 206.169.55.66 255.255.255.255 outsideSSH timeout 5
Console timeout 0
management-access inside
dhcpd 4.2.2.2 dns 8.8.8.8
!
dhcpd address 10.7.150.10 - 10.7.150.30 WLAN_GUESTS
enable WLAN_GUESTS dhcpd
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
SSL encryption rc4 - md5 of sha1
SSL-trust A1 out point
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-dart-win-2.5.2019-k9.pkg 1 image
enable SVC
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
internal VPNUsers group strategy
Group Policy VPNUsers attributes
value of server DNS 10.7.30.20
Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_users_splitTunnelAcl
dwm2000.WM.State.AZ.us value by default-field
Split-dns value dwm2000.wm.state.az.us
username HCadmin password * encrypted privilege 15
attributes global-tunnel-group DefaultWEBVPNGroup
address VPN_POOL pool
authentication-server-group ADWM-FPS-02
strategy - by default-VPNUsers group
tunnel-group 206.169.55.66 type ipsec-l2l
IPSec-attributes tunnel-group 206.169.55.66
pre-shared key *.
tunnel-group 159.87.64.30 type ipsec-l2l
IPSec-attributes tunnel-group 159.87.64.30
pre-shared key *.
!
class-map IPS_TRAFFIC
corresponds to the IPS_TRAFFIC access list
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the icmp
Review the ip options
class IPS_TRAFFIC
IPS inline help
!
global service-policy global_policy
field of context fast hostname
anonymous reporting remote call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:e70de424cf976e0a62b5668dc2284587
: end
ASDM image disk0: / asdm-645 - 206.bin
ASDM location 159.87.70.66 255.255.255.255 inside
ASDM location 208.65.144.0 255.255.248.0 inside
ASDM location 208.81.64.0 255.255.248.0 inside
ASDM location 172.16.10.0 255.255.255.0 inside
ASDM location 159.87.64.30 255.255.255.255 inside
don't allow no asdm historyAnyone have any ideas?
Hello
Please, add this line in your configuration and let me know if it works:
access extensive list ip 10.7.30.0 inside_nat0_outbound allow 255.255.255.0 10.7.30.0 255.255.255.0
I ask you to add that it is because you have not specified any exceptions for the return shipping. Once you add to it, will allow you to go through the tunnel VPN, packets back. When this command is not there, you will be able to access everything on the SAA but nothing behind it.
Let me know if it helps.
Thank you
Vishnu
-
Cannot ping internal VPN network.
I'm trying to understand why my VPN client can't ping my internal network of 192.168.0.X. For example, I can access my server via a \\192.168.0.14\Drive network drive mapping but I can't ping. I am trying to troubleshoot some phones Avaya VPN and want to ensure that I can ping the machines needed.
Thank you
Manny
Here is my config
ASA5505-xxxx # sh run
: Saved
:
ASA Version 8.0 (4)
!
hostname xxxxxx
domain xxxx.com
activate the xxxxxxxx password
passwd xxxxxx
names of
name Roosevelt 192.168.2.0
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 173.x.x.x 255.255.255.240.
!
interface Ethernet0/0
Description link to xx.x.x. Router
switchport access vlan 2
!
interface Ethernet0/1
Description LINK to Linksys SR2024
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa804 - k8.bin
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS server-group DefaultDNS
xxxxx.com domain name
permit same-security-traffic intra-interface
access-list 110 extended permit tcp any host 173.le eq xxxx 3389
access-list 110 extended permit tcp any host 173.le eq www xxxx
access-list 110 extended permit tcp any host 173.le eq smtp xxxx
access-list 110 extended permit tcp any host 173.le eq xxxx area
access-list 110 extended permit tcp any host 173.le eq https xxxx
access-list 110 extended permit tcp any host 173.le eq ftp xxxx
access-list 110 extended allow icmp a whole
access-list 110 extended permit tcp any host 173.le eq xxxx 3389
access-list 110 extended permit tcp any host 173.165.93.164 eq www
access-list 110 extended permit tcp any host 173.165.93.164 eq smtp
access-list 110 extended allow tcp no matter what field of host 173.165.93.164 eq
access-list 110 extended permit tcp any host 173.165.93.164 eq https
access-list 110 extended permit tcp any host 173.165.93.164 eq ftp
access-list 110 extended permit tcp any host 173.165.93.163 eq 3389
access-list 110 extended permit tcp any host 173.165.93.163 eq www
permit access ip 192.168.0.0 scope list Inside_nat0_outbound 255.255.255.0 255.255.255.0 Roosevelt
Inside_nat0_outbound list of allowed ip extended access any 10.10.1.0 255.255.255.0
permit access ip 192.168.0.0 scope list outside_1_cryptomap 255.255.255.0 255.255.255.0 Roosevelt
Standard access list CSC_splitTunnelAcl allow a
pager lines 24
Enable logging
exploitation forest-size of the buffer of 1000000
debug logging in buffered memory
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 10.10.1.1 - 10.10.1.10 255.255.255.0 IP local pool VPNPool
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 613.bin
don't allow no asdm history
ARP timeout 14400
Global interface 5 (external)
NAT (inside) 0-list of access Inside_nat0_outbound
NAT (inside) 5 0.0.0.0 0.0.0.0
public static 173.le (Interior, exterior) xxxx 192.168.0.14 netmask 255.255.255.255
public static 173.le (Interior, exterior) xxxx 192.168.0.17 netmask 255.255.255.255
public static 173.le (Interior, exterior) xxxx 192.168.0.12 netmask 255.255.255.255
public static 173.le (Interior, exterior) xxxx 192.168.0.11 netmask 255.255.255.255
public static 173.le (Interior, exterior) xxxx 192.168.0.13 netmask 255.255.255.255
Access-group 110 in external interface
Route outside 0.0.0.0 0.0.0.0 173.le xxxx 1
Timeout xlate 03:00
Timeout conn 0 half-closed 10:00:10: 00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.0.0 255.255.255.0 inside
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-AES-128-SHA ESP ESP-AES-128-MD5 ESP-AES-192-SHA-AES-192-MD5
ESP-AES-256-SHA SHA-ESP-3DES ESP-AES-256-MD5 ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define security association lifetime 28800 seconds
cryptographic kilobytes 4608000 life of the set - the association of security of the 65535 SYSTEM_DEFAULT_CRYPTO_MAP of the dynamic-map
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set counterpart 99 xxxxx
card crypto outside_map 1 set of transformation-ESP-DES-SHA
outside_map map 1 lifetime of security association set seconds 28800 crypto
card crypto outside_map 1 set security-association life kilobytes 4608000
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 10
preshared authentication
the Encryption
sha hash
Group 2
life 86400
ISAKMP nat-traversal crypto
Telnet timeout 5
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 10
Console timeout 0
dhcpd 192.168.0.14 dns 68.87.77.130
dhcpd wins 192.168.0.14
dhcpd domain xxxx.com
!
dhcpd address 192.168.0.50 - 192.168.0.150 inside
dhcpd allow inside
!a basic threat threat detection
host of statistical threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal group CSC policy
attributes of group CSC policy
value of 192.168.0.14 WINS server
VPN-idle-timeout no
Protocol-tunnel-VPN IPSec svc
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list CSC_splitTunnelAcl
username lrodriguez password xxxxxx
username lrodriguez attributes
VPN - 10 concurrent connections
username password xxxxx jthomas
username mramirez password xxxxx
tunnel-group 99 xxxx type ipsec-l2l
tunnel-group 99 xxxx ipsec-attributes
pre-shared-key *.
tunnel-group CSC type remote access
attributes global-tunnel-group CSC
address pool VPNPool
Group Policy - by default-CSC
tunnel-group CSC ipsec-attributes
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
!
global service-policy global_policy
Server SMTP 192.168.0.xx
context of prompt hostnameOn the VPN Client PC, see if there is any firewall is activated. Tried to disable the firewall, if it's on.
I suppose also that the Avaya server default gateway is 192.168.0.1?
-
VPN question: ISP assigned a private ip address
Hi all
Internet-online-online headquarters VPN 3015 concentrator
Users remote VPN Client connected to the internet using a private ip address provided by the ISP (cable) is to establish a VPN tunnel, but they can not ping our private network.
The only way to get the VPN works is when remote users use a public ip.
It is a question of Cisco VPN Client? Or it has a solution...
Thanks in advance,
Kind regards
Carlos Welhous
Network engineer
Hi Carlos,
If your ISP gave you a private address, they must use NAT - in which case you will have to enable NAT - T on the VPN concentrator.
To configure the NAT - T in the world, go to Configuration | System | Tunnelling protocols. IPSec | Screen of transparent NAT and check on NAT - T IPSec case.
-
VPN - question of General design for a ut of a router tunnel more
Hello
We have a router that has VPN connections with different partners of our company. VPN remote access were used on computers that are connecting to the different partners of our company.
There has been problems of this kind, that is to say put on both a watchdog and a customer vpn cisco router led to blue-screens on the PC.
The current idea is to put different tunnels from site to site on the router (default gateway of PC clients that connect to the partners). My question is... How our PC to get DHCP addresses on networks of visitors, once the tunnels are up? I guess I'm alittle confused about the address for the PC on our side how will work.
Thanks for your help.
Divide the pool of ip from the internal network, you're going to visit. for example the document below will be exaplain the same configuration in user mode.
-
Try to find what happened. I had the remote end raise the tunnel, as they can ping resources on my side. I am unable to ping 10.90.238.148 through this tunnel. I used to be able to until the interface of K_Inc has been added. The network behind this interface is 10/8.
I asked a question earlier in another post and advises him to play opposite road of Cryptography. And who did it. I was able to ping 10.90.238.148 of 192.168.141.10, with the config below.
I am at a loss to why I can't all of a sudden. A bit of history, given routes have not changed. By adding the command set opposite road to cryptography, I find myself with a static entry for the 10.90.238.0 network is what fixed it initially so I don't think it's a problem of route. The remote end had an overlap with the 192.168.141.0/24 that is why my side is natted on the 10.40.27.0. None of the nats have changed so if adding the reverse route worked for a day, it should still work. Any thoughts?
interface GigabitEthernet0/3.10
VLAN 10
nameif K_Inc
security-level 100
IP address 192.168.10.254 255.255.255.0
interface GigabitEthernet0/3.141
VLAN 141
cold nameif
security-level 100
IP 192.168.141.254 255.255.255.0
(Cold) NAT 0 access-list sheep
NAT (cold) 1 192.168.141.0 255.255.255.0
Access extensive list ip 192.168.141.0 CSVPNOFFSITE allow 255.255.255.0 10.90.238.0 255.255.255.0
Access extensive list ip 10.40.27.0 CSVPNOFFSITE allow 255.255.255.0 10.90.238.0 255.255.255.0
Access extensive list ip 192.168.141.0 CSVPNNAT allow 255.255.255.0 10.90.238.0 255.255.255.0
IP 10.40.27.0 allow Access-list extended sheep 255.255.255.0 10.90.238.0 255.255.255.0
static 10.40.27.0 (cold, outside) - CSVPNNAT access list
card crypto Outside_map 5 corresponds to the address CSVPNOFFSITE
card crypto Outside_map 5 the value reverse-road
card crypto Outside_map 5 set pfs
card crypto Outside_map 5 set peer 20.x.x.3
Outside_map 5 transform-set ESP-3DES-MD5 crypto card game
card crypto Outside_map 5 defined security-association life seconds 28800
card crypto Outside_map 5 set security-association kilobytes of life 4608000
tunnel-group 20.x.x.3 type ipsec-l2l
20.x.x.3 Group of tunnel ipsec-attributes
pre-shared-key *.
Route outside 0.0.0.0 0.0.0.0 7.x.x.1 1
Route 10.0.0.0 K_Inc 255.192.0.0 192.168.10.252 1
Route K_Inc 10.64.0.0 255.224.0.0 192.168.10.252 1
Route K_Inc 10.100.100.0 255.255.255.0 192.168.10.252 1
Route K_Inc 10.128.0.0 255.128.0.0 192.168.10.252 1
Tunnel is up:
14 peer IKE: 20.x.x.243
Type: L2L role: answering machine
Generate a new key: no State: MM_ACTIVE
EDIT:
I just noticed when tracer packet i run I don't get a phase VPN or encrypt:
Packet-trace entry cold tcp 192.168.141.10 80 80 10.90.238.148 det
Phase: 1
Type: FLOW-SEARCH
Subtype:
Result: ALLOW
Config:
Additional information:
Not found no corresponding stream, creating a new stream
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 10.90.238.0 255.255.255.0 outside
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xad048d08, priority = 0, sector = option-ip-enabled, deny = true
hits = 2954624, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 4
Type: QOS
Subtype:
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xb2ed4b80, priority = 72, domain = qos by class, deny = false
hits = 2954687, user_data = 0xb2ed49d8, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 5
Type: FOVER
Subtype: Eve-updated
Result: ALLOW
Config:
Additional information:
Direct flow from returns search rule:
ID = 0xad090180, priority = 20, area = read, deny = false
hits = 618776, user_data = 0 x 0, cs_id = 0 x 0, flags = 0 x 0, Protocol = 6
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
static (ColdSpring, external) 74.x.x.50 192.168.141.10 netmask 255.255.255.255
match ip host 192.168.141.10 ColdSpring outside of any
static translation at 74.x.x.50
translate_hits = 610710, untranslate_hits = 188039
Additional information:
Definition of static 192.168.141.10/0 to 74.112.122.50/0 using subnet mask 255.255.255.255
Direct flow from returns search rule:
ID = 0xac541e50, priority = 5, area = nat, deny = false
hits = 610742, user_data = 0xac541c08, cs_id = 0 x 0, flags = 0 x 0 = 0 protocol
SRC ip = 192.168.141.10, mask is 255.255.255.255, port = 0
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 7
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (ColdSpring, dmz) 192.168.141.0 192.168.141.0 netmask 255.255.255.0
match ip ColdSpring 192.168.141.0 255.255.255.0 dmz all
static translation at 192.168.141.0
translate_hits = 4194, untranslate_hits = 20032
Additional information:
Direct flow from returns search rule:
ID = 0xace2c1a0, priority = 5, area = host, deny = false
hits = 2954683, user_data = 0xace2ce68, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 192.168.141.0, mask is 255.255.255.0, port = 0
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Reverse flow from returns search rule:
ID = 0xaacbcb90, priority = 0, sector = option-ip-enabled, deny = true
hits = 282827537, user_data = 0 x 0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 9
Type: QOS
Subtype:
Result: ALLOW
Config:
Additional information:
Reverse flow from returns search rule:
ID = 0xb2ed5c78, priority = 72, domain = qos by class, deny = false
hits = 4749562, user_data = 0xb2ed5ad0, cs_id = 0 x 0, reverse, flags = 0 x 0 = 0 protocol
SRC ip = 0.0.0.0 mask 0.0.0.0, port = 0 =
DST ip = 0.0.0.0 mask = 0.0.0.0, port = 0, dscp = 0 x 0
Phase: 10
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 339487904 id, package sent to the next module
Information module for forward flow...
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_fp_tracer_drop
snp_ifc_stat
Information for reverse flow...
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_fp_tracer_drop
snp_ifc_stat
Phase: 11
Type:-ROUTE SEARCH
Subtype: output and contiguity
Result: ALLOW
Config:
Additional information:
found 7.x.x.1 of next hop using ifc of evacuation outside
contiguity Active
0007.B400.1402 address of stretch following mac typo 51982146
Result:
input interface: cold
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
What version are you running to ASA?
My guess is that your two static NAT is configured above policy nat you have configured for the VPN? If this is the case, move your above these static NAT NAT policy and you should see the traffic start to flow properly.
--
Please note all useful posts
-
Cisco ASA 5520 cannot ping between VPN Tunnels
I have the main site and sites A and B. A to connect to the hand and B connects to the main. I can ping from A hand and has for main. I can ping from main to B and B to main. However, I can not ping from A to B. A and B are sonicwall 2040 and main is a 5520. The question should not be with the 5520 none allowing traffic between the two VPN Tunnels, but I can't understand why it does not work. Can someone give an idea on that? Thanks in advance.
Hello
I see that you use ASDM. Always makes my eyes bleed when I need to look at the DM_INLINE of named objects and try to make sense the CLI format
Seems to me that there are problems with the NAT.
If you don't mind a small break between the main Site and remote locations, I'd say changing some follows the NAT configuration
Remove old
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_9 DM_INLINE_NETWORK_10 DM_INLINE_NETWORK_10 non-proxy-arp-search of route static destination
no nat source (indoor, outdoor) public static DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_11 DM_INLINE_NETWORK_12 DM_INLINE_NETWORK_12 non-proxy-arp-search of route static destination
Add a new
object-group network NETWORK-2790
object-network 10.217.0.0 255.255.255.0
object-network 10.217.1.0 255.255.255.0
object-group network NETWORK-3820
object-network 10.216.0.0 255.255.255.0
object-network 10.216.1.0 255.255.255.0
object-group network NETWORK-COLO
object-net 10.8.0.0 255.255.255.0
destination of NETWORK of NETWORK-2790-2790 static NAT (outside, outside) static source NETWORK - 3820 - 3820
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 2790 - 2790
NAT static destination of NETWORK of NETWORK-COLO-COLO (indoor, outdoor) static source NETWORK - 3820 - 3820
The first new line of configuring NAT manages the NAT0 configuration for traffic between SiteA and SiteB. The following configurations of NAT 2 manage the NAT0 for traffic between the main Site - hand Site SiteA - SiteB
-Jouni
-
Hi, I use the windows Server 2003 and. When I access my server at home I connect the VPN but I not have access to the shared private folder when I try to open the system crashes but the other file I can open without blocking. Please help me solve this problem...
Hi Patchamuthu,
Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for support on Windows server. Please post your question in the below link:http://social.technet.microsoft.com/Forums/en/itproxpsp/threads
With regard to:
Samhrutha G S - Microsoft technical support.
Visit our Microsoft answers feedback Forum and let us know what you think.
-
I have two questions that regarding ACL is used in the instructions on the Card Crypto:
1. the two devices VPN should have the same ACE in the ACL? I know that without the second ACE site B below will not see as interesting udp traffic, but the will of the vpn tunnel fails because the ACL is not the same ACE?
That is to say...
Site has
Access-list 110 permit tcp 10.0.1.0 255.255.255.0 10.0.2.0 255.255.255.0
Access-list 110 permit udp 10.0.1.0 255.255.255.0 10.0.2.0 255.255.255.0
Site B
Access-list 110 permit tcp 10.0.2.0 255.255.255.0 10.0.1.0 255.255.255.0
2. once a tunnel is established it will send ANY/ALL traffic destined to the remote network through this tunnel. If the first ACE in the ACL 110 to Site A list is used to bring up the tunnel, only tcp from to 10.0.2.0/24 10.0.1.0/24 traffic will use the tunnel or all traffic from 10.0.1.0/24 intended for the remote network to cross the tunnel?
I guess my thought is this. The ACL is only used to determine valuable traffic and once the tunnel is up it is a free for all. Or the ACL only allows traffic that meets the criteria specified in the ACL list to flow once the tunnel is established?
Thank you
Brian
Brian,
Your statement
'Or the ACL allows only traffic that meets the criteria specified in the ACL list to flow after the tunnel is established'
Is correct, only the traffic that meets the ACL crypto will go through the vpn tunnel and all other traffic will be denied. If you need UDP traffic to travel through the tunnel, you need crypto ACL on both sides and not only on one side, that is, SITE A.
Hope this helps,
Jay
-
Hello
I created a vpn between two routers in two different sites. The VPN works well, but I noticed something that I can ping from peer1 at peer2 however the tunnel although the ACL of the interesting traffic allows no icmp between two counterparts, it is configured as follows:
access-list 120 allow ip 10.10.10.0 255.255.255.0 192.168.2.0 255.255.255.0
access-list 120 allow ip 1.1.1.1 host 2.2.2.2
No icmp is allowed, but the icmp traffic is encapsulated, encrypted, and through the tunnel, why?
Hello moahmed1981,
When you configure access-list for IPs, so it includes ICMP, TCP, and UDP, therefore, it is expected that you will be able to ping across the tunnel.
If you want to change this, please configure the VPN filter to prevent the ping to the vpn tunnel.
Here's a doc for your reference:-
https://popravak.WordPress.com/2011/11/07/Cisco-IOS-VPN-filter/Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Hello world
The vendor name is implemented server in our environment.
We implement VPN site-to-site.
Subnet it is interesting traffic 192.168.50.x
Server IP 192.168.50.1 - Switch1 - ASA - Site to site VPN - provider ASA.
Gateway server is on switch1 if this server requires access to the internet I need to know what config I need on ASA on my site?
I want the server to access the internet through the provider network
Concerning
Mahesh
Hello
Your crypto ACL would be:
ip access-list VPN-TO-VENDOR permit ip 192.168.50.0 255.255.255.0 any
Cryptography providers ACL would be:ip acces-list VPN-TO-COMPANY permit ip any 192.168.50.0 255.255.255.0
All traffic from 192.168.50.0/24 out of the application interface map encryption for any destination would be sent to the seller through the VPN. It will be useful. -
Inside the server can't ping remote vpn client
My simple vpn client can accumulate the tunnel vpn with my Office ASA5510 success and my vpn client can ping the internal server. But my internal server cannot ping the remote vpn client. Even the firewall vpn client windows is disable.
1. in-house server can ping Internet through ASA.
2 internal server cannot ping vpn client.
3 Vpn client can ping the internal server.
Why interal Server ping vpn client? ASA only does support vpn in direction to go?
Thank you.
Hello
Enable inspect ICMP, this should work for you.
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the icmp
inspect the icmp errorinspect the icmp
To configure the ICMP inspection engine, use the command of icmp inspection in class configuration mode. Class configuration mode is accessible from policy map configuration mode.
inspect the icmp
HTH
Sandy
-
VPN question, can connect, but can, t go anywhere
Hello
I have my house 2621xm router and I have configured my router as a vpn server and I can connect using vpn client, but that's all I can do. I can't ping or go anywhere. I can't find all the documents on cisco or google that can help me here, so here I am.
Basically, I give the client vpn ip 192.168.6.X then I want the customer to be able to go anywhere in the 192.168.1.X range 5.X and 10.X.
any help would be appreciated to greately!
Try,
crypto dynamic-map VTELDYNAMAP 10
market arriere-route
Kind regards
Prem
Maybe you are looking for
-
problems with ipod touch ios 9.3.2 and gen 6
I own an iPod Touch generation 6 with 32 GB. My PC is a Windows 7 PC. My iTouch is looking forward to start a SOFTWARE iOS 9.3.2 UPDATE. I heard that there are "problems" with iOS 9.3.2. I have not read that they affect the iPod Touch. But who re
-
Mail rules 'no mailbox not selected' madness
I used a set of rules to mail in Mail.app 50 for about ten years now. He has always been a struggle. Mysteriously disabled mail rules and many other problems. But now the whole system is just crazy completely. Desperately, I ask someone to help me, p
-
Portege M100 runs at 600 MHz after the BIOS/FRIMWARE upgrade
Hello I received a Portege M100, this week, installed Debian GNU/Linux (Sid) on it and almost everything was fine.Then I upgraded to the latest BIOS/FIRMWARE (from V1.10 to V1.50) and now my Pentium M 1200 MHz running at half speed.I can not load als
-
Flight Simulator gold an extension?
Hello! I have Flight Simulator X standard, and I want to use FSX Gold, with the luxury and acceleration. What is an extension to the standard kit? Thank you
-
If I have windows vista 32 bit, how can I update it and make it run faster is now runinng to 2.1?
I have windows vista using 32 bit how I up date and rotate faster is it running at 2.1? my desktop and laptop are running on the same why so my office so slow?