GETVPN Configuration Tips

Similar Questions

• VMware configuration tips

  Hello guys,.

  Want just confim if these configuration would work on VMWARE ESXi 3.5

  AMD AM3 CPU QUAD CORE 7850 ADX2400CGQ +.

  KINGSTON 2 GB PC 667 / 800 DDR 2 RAM CL6

  BIOSTAR MOTHERBOARD INTEGRATED AM2 MCP6P

  160 GB SATA HARD DRIVE

  Please let me know if it will work...

  Thank you

  Ashvin

  This should work for you... and you should be able to install ESXi on the following hardware or are looking for the following link for the hardware compatibility.

  FYI > ESXi 3.5 have limited support for SATA

  http://www.VMware.com/resources/compatibility/search.php?source=HP&q=HCL%20For%20vmware&meta=&AQ=f&OQ=

  Please keep posting, if you face any problem during the installation.

• Security Configuration Tips

  I'm looking for the feedback & advice on the attached config (1801 fixed router) to see if I can improve my ACL / CBAC and general implementation of security. Any advice would be most appreciated.

  Concerning

  Hi mike,.

  Looks like a good Setup. But a few ratings points are

  (1) you have no aaa accounting enabled.

  (2) your password encryption is low class 7. You can improve by using username mike secret privilege 15

  Rate if helps.

  Naveen B

• Lack of Configuration section in VAMI, vCenter active watch is not Accessible after upgrade from 5.5 to 5.8

  Hi all!  I'm having a bit of a problem that I can't find a solution for anywhere.

  I have a lab with two boxes of vcsa under 5.5 U2d, and wanted to move to 5.8 SRM.  I started the VRA 5.5.1 (I do not remember, real version number which was with MRS 5.5.1), mount the ISO 5.8 on both sides, restarted both, took the update of the CD (following the official update steps), but after the restart, the two vCenters show "enabled (not available)" and still list it as 5.5.1.

  I have validated the RV service is running.  I have been following this thread, regenerated certificates for the TWO vCenters & TWO VRAs: vsphere upgrade from 5.5 to 5.8 Server replication enabled (not accessible) has yet no joy.

  I checked the CROWD and the IP address is correct.  I tried to check /opt/vmware/hms/conf/extension.xml for the thumbprint and the file does not exist on each box, the only thing it is extension - template.xml.

  On the one hand, I have reset the vCenter database (/ usr/sbin/vpxd - d of VMware KB: reset the vCenter Server repository embedded for vCenter Server Appliance 5.x ), deployed a new VRA 5.8, and he had to register very well.  It's then it dawned on me what missed me: almost all the Startup Configuration where you specify the vCenter (see attachment)

  For grins, I recorded the VRA 5.8 of the 'old' vcsa work and tried to save it to the 'new' vcsa, which he could not with a lot of what looked like errors, assuming that because of 'new' vcsa already having a recorded SOAP VRA.  I re-recorded it back to the 'old' vcsa and is happy.  Installed SRM 5.8 (uninstalled 5.5 because I started with a clean database in the vcsa) and all is well on the side of the 'old '.

  I'm trying not to go this route on the 'new' side, as I a VDS, vSAN and twice as many hosts, so I won't recreate the vDC, cluster, add guests, etc.  I copied to /opt/vmware/hms/conf/extension-template.xml /opt/vmware/hms/conf/extension.xml and restarted.  Footprint arises, but still no configuration tips.

  Anyone have any ideas?

  Thanks for your reply. You said that the VRA is on a cluster, East of thatcluster HA-enabled? Because where HA must restart the VRA on another host, it does so through the ESX host and this could have emptied the OVF environment. And to even you'll always a working configuration until you start the upgrade or you try to perform any operation through VAMI configuration page. To be on the safe side, I think before upgrade, you can power off and then turn the unit on (simple restart is not enough) to make sure that the EPS of the FVO is recreated.

• How to back up the configuration of weblogic

  I determined experimentally that it is possible to lose the weblogic configuration, the stuff that sets WLS_FORMS
  and WLS_REPORTS, etc. Because we don't know how it happened, I would like to know if I can save this configuration
  Tips and say put it back if it happens again? Where is that going?

  It is important for you the backup configuration + applications for the safer side.

  Please see the document below. It says how to

  http://www.Oracle.com/technetwork/database/features/availability/MAA-WP-WLS-BR-scenarios-128715.PDF

• B2B 11 g - how to configure AS2?

  Hello
  
  We must set up a channel AS2 for exchanging documents with our TP. I find the steps that we need to do. I went through the link: http://www.b2bgurus.com/2009/01/security-configuration-in-oracle-as.html. Things are pretty clear here. I'm not able to understand the steps 2 and 3, which are:
  
  Step 2: Import the certificate to host in the Oracle Wallet as well as the root certificate.
  
  Step 3: Make sure that you specify the location of portfolio properly (folder name) in the ip/configuration/tip.properties file.
  
  For example oracle.tip.adapter.b2b.WalletLocation = c: / tmp/soa/b2b
  
  I use 11g and unable to understand what is Oracle Wallet and to configure the oracle.tip.adapter.b2b.WalletLocation location since I'm did not find the file tip.properties. Or I could find this property in Administration-> Configuration page.
  
  Help, please.
  
  Thank you
  Sanjay
  
  Published by: Sanjay Bharatiya December 6, 2010 09:31

  Hello Sanjay

  If you want to enable SSL on B2B of Oracle 11g (if you wish to send documents over HTTPS using AS2), then please refer-

  http://Anuj-Dwivedi.blogspot.com/2010/10/enabling-SSL-on-Oracle-B2B-11g.html

  The link you are talking about is for Oracle 10g B2B.

  Kind regards
  Anuj

• Modes of failure in TCP WRITE?

  I need help to diagnose a problem where TCP communication breaks down between my host (Windows) and a PXI (LabVIEW RT 2010).

  The key issues are:

  1... are there cases where to WRITE TCP, a string of say 10 characters, write more than zero and less than 10 characters for the connection? If so, what are those circumstances?

  2... is it risky to use a 1ms timeout value?  A reflection seems to say that I won't get a timeout in uSec 1000 if we use a database of time 1-ms, but I don't know if this is true in PXI.

  Background:

  On the PXI system, I use a loop of PID-100 Hz, controlling an engine.  I measure the speed and torque and control the speed and the throttle.  Along the way, I am in a position 200 channels of various things (analog, CAN, instruments of TCP) at 10 Hz and sending masses of info to the host (200 chans * 8 = 1600 bytes every 0.1 sec)

  The host sends commands, responds the PXI.

  The message protocol is a type of variable to fixed header, payload: a message is a fixed 3-byte header, consisting of a U8 OpCode and a USEFUL of U16 load SIZE field. I flattened a chain structure, measuring its size and add the header and send it as a TCP WRITE.  I get two TCP reads: one for the header, then I have the heading unflatten, read the SIZE of the payload and then another read for that many more bytes.

  The payload can be zero byte: a READING of TCP with a byte count of zero is legal and will succeed without error.

  A test begins by establishing a connection, configuration tips, and then sampling. The stream of 10 Hz is shown on the home screen for 2 Hz as digital indicators, or maybe some channels in a chart.

  At some point the user starts RECORDING, and 10 Hz data go into a queue for later write to a file. It is while the motor is powered through a cycle prescribed target speed/torque points.

  The registration lasts for 20 or in some cases for 40 minutes (24000 samples) and then recording stops, but sampling does not.  Data are still coming and mapped. The user can then do some special operations, associated with audits of calibration and leaks, and these results are stored.  Finally, they hit the DONE button and the mess is written to a file.

  This has worked well for several years, but that the system is growing (more devices, more channels, more code), a problem arose: the two ends are sometimes get out of sync.

  The test itself and all the stuff before configuration, works perfectly. The measure immediately after the test is good.  At some point after that, he goes to the South.  The log shows the PXI, sending the results for operations that were not opposed. These outcome data are garbage; 1.92648920e - 299 and these numbers, resulting from the interpretation of random stuff like a DBL.

  Because I wrote the file, the connection is broken, the next test he reestablished and all is well again.

  By hunting all of this, I triple-checked all my shipments are MEASURES of the size of the payload before send it.  Two possibilities have been raised:

  1... There is a message with a payload of 64 k.  If my sender was presented with a string of length 65537, it would only convert a value U16 1 and the receiver would expect 1 byte. The receiver would then expect another heading, but these data come instead, and we are off the rails.

  I don't think what is happening. Most messages are less payload of 20 bytes, the data block is 1600 or so, I see no indication of such a thing to happen.

  2... the PXI is a failure, in certain circumstances, to send the entire message given to WRITE of TCP.  If she sends a header promising more than 20 bytes, but only delivered 10, then the receiver see the header and wait more than 20. 10 would come immediately, but whatever the message FOLLOWING, it's header would be interpreted as part of the payload of the first message, and we are off the rails.

  Unfortunately, I'm not checking the back of writing TCP error, because she's never not in my test here (I know, twenty lashes for me).

  It occurs to me as I was him giving a value of timeout 1-mSec, since I am in a loop of 100 Hz. Maybe I should have separated the TCP stuff in a separate thread.  In any case, maybe I do not get a full 1000 uSec, due to problems of resolution clock.

  This means that TCP WRITE failed to get the data written before the time-out expires, but he wrote the part of it.

  I suspect, but newspapers do not prove, that the point of failure is when they hit the DONE button.  The General CPU on PXI is 2 to 5%, at that time there are 12 to 15 DAQ field managers to be close, so the instant the CPU load is high.  If this happens to coincide with an outgoing message, well, perhaps that the problem popped up.  It doesn't happen every time.

  So I repeat two questions:

  1... are there cases where to WRITE TCP, a string of say 10 characters, write more than zero and less than 10 characters for the connection? If so, what are those circumstances?

  2... is it risky to use a 1ms timeout value?  A reflection seems to say that I won't get a timeout in uSec 1000 if we use a database of time 1-ms, but I don't know if this is true in PXI.

  Thank you

  If a TCP write operation times out, it is possible that some data did in fact get placed in the buffer, and it will be read by the other side. This is why there is an output bytes written on TCP Write function, to determine what was actually put in the buffer.

  To account for this, you can proceed as follows:

  1. do an another TCP write and send only the subset of the first package that does not get completely passed. Use bytes written to Get String subset for the remaining data.

  2. start with greater delays.

  3. in the case of a timeout, the close link and force a reconnection so that the data of the partially filled buffer not get transformed by the other side.

• Problem to run Agilent GPIB with NI-VISA card: recurring at Agilent VISA 32 report of open conflict that all things set correctly...

  Hi developers OR,.

  I have a recurring problem to correct my installation using a labview and Agilent GPIB card.

  Of course, the well-known configuration tips are generally defined:

  -Agilent VISA a VISA secondary (by-side mode)

  -the passport for tulip is enabled in NOR-MAX

  -OR-488 support active in Agilent librabry suite 16.1

  I uninstalled and reinstalled any component twice, but still get the same error message when I want to talk to a Keithley 2400 EMS:

  -Firstly, the agilent GPIB interface is correctly recognized expert Agilent connection and NOR-MAX

  -Then the instrument of 2400 keitjley initially works correctly in Agilent connection Expert and NOR-MAX

  BUT: when I try to send a command to the device (whether through the wizard or VISA using the Labview instrument driver), the tool returns an error (error "Application incomplete" punch followed immediately by a second "Invalid while in the local" error code)

  At the same time, the Manager (32 open report VISA) conflict in expert Agilent connection says "NI-VISA has returned an error. "There is a conflict of interface between NI-VISA and VISA Agilent". He suggested that the conflict occurs when different interfaces receive the same number of interface in the two VISA.

  Therefore, aware of the conflict that can occurs in a side-by-side installation, I tried to change the ID of Interface CLCL's Board of Directors in the Agilent connection Expert (from gpib0 to gpib9) and restart, but it did not help.

  So can you help me solve this recurring problem?

  Is it necessary to also change the VISA interface ID, or address of the GPIB Board Agilent GPIB in connection Expert? Wouldn't be the same address (9 for example)?

  I really do not understand.

  Sorry for this new message on the configuration of this topics, but I found no useful advice in the forums.

  See you soon,.

  Yoyo87.

  Finally, I got my system running after several tests, although I couldn't use NI-VISA as first VISA (allowing the tulip passport) with agilent VISA (permit for programs OR-488) at the same time.

  I uninstalled it all components of NOR and the agilent and re - install in the correct order (OR first, followed by agilent): nothing has changed.

  I check for updates of agilent and NOR and use several different versions of VISA at the same time: nothing has changed and I still communication errors when you try to send the order through NI-VISA Interactive control or labview (although it worked well by expert agilent of connection).

  I don't really know why, but I solved my problem by installing Agilent VISA primary visa. In this way, even if I do not see the Council of Agilent in NOR-MAX, I can always send control of GPIB instruments by labview using their VISA address or aliases defined in connection expert Agilent...

  I am always interested to understand why I was not able to run the two VISAs on my system with agiulent only one card PCI GPIB... so if one of you sees a clear reason for this...

  Thanks in any case, even if I don't have a lot of response on this topic...

  Yoyo87

• Cisco 1941: no risk in "ip Routing" or "ip cef" for NetFlow when bypass

  Hello

  It's on a router Cisco 1941.  version 15.1 ipv4 only.

  I would like to enable Netflow v9 for use with PRTG bandwidth monitoring.

  I tried the instructions at http://kb.paessler.com/en/topic/563-do-you-have-any-configuration-tips-for-cisco-routers-and-prtg and the first step fails because I

  no ip Routing
  No cef

  in my running-config.  More precisely, this

   interface GigabitEthernet 0/1 ip route-cache flow exit 

  fails with the error message "ip Routing not enabled."

  I have read conflicting information on the question if I need to change one or both of these lines.  And I have enough to http://www.cisco.com/c/en/us/td/docs/ios/15_1/release/notes/15_1m_and_t/151-4MCAVS.html afraid to try just scanned.

  I hope that's enough of my config for someone to give some useful information.  Note the BYPASS.

  interface GigabitEthernet0/0
 no ip address
 no ip redirects
 no ip unreachables
 no ip route-cache
 load-interval 30
 duplex auto
 speed auto
 no cdp enable
 no mop enabled
 bridge-group 1
 bridge-group 1 spanning-disabled
!
interface GigabitEthernet0/1
 bandwidth 10000
 ip address 201.201.201.51 255.255.255.0
 ip access-group 110 in
 ip access-group 120 out
 no ip redirects
 no ip unreachables
 no ip route-cache
 load-interval 30
 duplex auto
 speed 10
 no cdp enable
 bridge-group 1
 bridge-group 1 spanning-disabled
!
ip default-gateway 201.201.201.1
ip forward-protocol nd
!
no ip http server
no ip http secure-server
ip flow-export version 9
ip flow-export destination 201.201.201.89 9991

  Looking forward to comments from a person with experience, do something similar.

  Thank you.

  We do not know anything about your environment or why you decided to activate ip Routing and fill. But there is probably a reason why you did that.

  The importance of this is that NetFlow data are generated as part of the routing decisions. And you prevent your router to make routing decisions as you have disabled ip Routing. So I don't see anyway that you can get this router NetFlow, as long you have disabled ip Routing.

  HTH

  Rick

• Best editing for Adobe Premiere Pro using laptop and external drive

  I'll confess that I'm not a particularly technical person. But I am learning!

  So I want to ask a simple question and hopefully get some good advice.

  I'm editing a feature-length documentary on Adobe Premiere Pro. I have a lot of HD footage, and I want to optimize my drives to optimize performance. To that end, I recently bought a StudioRAID 4 to glyph.

  I currently work for a Mac Book Pro. I use Mac OS 10.9.5.

  Processor: 2.66 Ghz Interl Core i7

  Memory: 4 GB 1067 Mhz DDR3 (2 GB 2 benches)

  I searched a bit on how to better implement my discs, getting some useful infor here: https://forums.adobe.com/thread/662972 and here: https://www.video2brain.com/en/lessons/optimizing-hard-disks

  But there is a little too much information - and I'm getting lost. Use a 2 disk configuration tips? Or should I partition my drive of new glyph and use the 3 disc mounting configuration.

  I'd appreciate certainly all of the tips!

  Thank you

  Rebecca

  partition the disks will not help and will not change readership by this ranking. better performance would use raid-0 on the StudioRaid of glyph and 2 disk configuration in the table. Make sure that there is a backup of the raid, in case something happens.

  also 4 GB of ram is dangerously low, you can upgrade to 16 gb.

• Connection to a SQL database with Windows authentication in a workflow?

  So far, I had a lot of chance to connect to and reading SQL DBS of workflows using SQL authentication (MS SQL). What I'm trying to do now is to connect to the databases same by using Windows authentication and I'm coming up with nothing.

  Someone at - it examples of correct connection URL and or the configuration tips to make this work? Can the vCO to connect using JDBC and Windows Auth at all in a workflow?

  Thank you!

  Colin J.

  Certainly, the best thing to do is to use the URL JDBC workflow Builder.

  It may take a little trial and error:

  If your stand-alone SQL Server, is not in the field, use the server for the Domain domain name.

  Field, use the domain for the domain domain

  If you have an instance, specify it, otherwise leave this field blank.

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.

• Tips on configuring firewall for MBP 2015

  I need advice on configuring firewall MBP2015... I am not sure on the best settings for this computer at home.  There is wifi connected to an AirPort Extreme router that is secure.

  Thanks in advance for any help

  GBL

  Your router has it's own built in firewall.  Airport utility > network > router Mode: DHCP and NAT are enabled, NAT firewall is enabled

  Therefore, you need not Mac Firewall is enabled in your network.

• JOINT-2: Tips for the initial configuration of the network?

  Hello team:

  I was asked to do a very basic configuration of a whole new JOINT-2 on a CAT6500. According to the documentation, once in the Supervisor´s CLI, I run a 'session' command to the location where the METHOD.

  Once, I follow the wizard to add the IP, mask and gateway. Having this configured, the management interface of module´s should be visible from the rest of the network, but I do not see how this happens, because the module must use one of VLAN switch´s and I haven´t found how it is configured.

  Question: how will this link JOINT itself for layer 3 engine switch´s? I don't see how its layer 2 will correspond to any VLAN available in the host LAN switch...

  Any help will be greatly appreciated

  Rogelio Alvez

  Argentina

  I think what you need to add a command on the 6500 that puts management of JOINT-2 port in a vlan individual.  For example:

  intrusion detection module 9 management access port - vlan 101

  This places the management for the joint-2 card port 9 slot vlan 101.  The host IP that you set on the map of JOINT-2 itself then be valid for that vlan.

  Steve

• I'm looking for 'best practices' tips for a configuration of a project (first CS5.5, Windows 7 Pro)

  I was instructed to update an old corporate video with narration, sounds, graphics and new music.

  Video camera ONLY material that I've had a DVD corporate (NTSC) - the original source material is simply not available. .

  I can rip the DVD in MPEG 2 and import it into first without problem, but I would like to be able to use resolutions higher the updated graphics.

  I intend to export it to Youtube (HD) but can export to DVD or BluRay as well.

  My question really reduced management of sequences.   I tell myself that my sequence settings must be the highest resolution, I expect to work with (Youtube HD or Bluray) which allows you to easily export to lower quality, but I don't really know if it's as simple as that.  Is there a standard method in the industry?  Am I close?

  First may actually use the DVD .vob files, just copy DVDs to hard disk, and then import in first.

  What is the DVD existing video in a 4:3 or 16:9 format? If 4:3, think about how you will work in a program of 16:9. Rather than having the black terminal on the side bars, many publishers will some sort of background to fill this space. A popular solution is to reproduce a bass track, stretch 4:3 video to fill the screen and add Gaussian blur effects. Because the colors/content of the sidebars will correspond to the main video, it's a little disguises the fact that the video is 4:3.

  If you put SD images in a HD program, it will look 'soft' compared to the HD images. As a compromise, you can consider the new edition as 720 p instead of 1080 p program, so that the SD resolution is not to be tense. All the computer video/video YouTube is not interlaced, meaning to sequences and exports should be done as Progressive.

  Flow problem of potential work - if you take the images existing SD from the DVD and it high end in a HD sequence, then export to DVD (SD resolution), the video turned into mush. She was raised, and then again once, dowscaled really kill the quality. May be required to copy the HD sequence in a sequence of SD, difficulty of the problems of size / scale of graphics and titles and DVD for the export of the sequence of SD to avoid the top of range/reduce images SD. Note that the DVD-video is highly compressed, so you already work with a weak source material, recompress again will be a hit in quality in all cases, but certainly avoid the top of range/cut again.

  I don't have Adobe apps in front of me at the moment, but I think that Blu - ray 720 p export options are limited, perhaps 720 p at 59.94 only, not sure. Which may affect your decision to 1080 p and 720 p.

  Hope these tips help you

  Thank you

  Jeff Pulera

  Safe Harbor computers