Guest WLAN with VLAN (Dell PC 6248)

Similar Questions

• Dell PowerConnect 6248 10 GB ports reference works do not

  Hello

  We have recently installed a module SFP + (part # c107d) in our Dell PowerConnect 6248 switch. The switch does not seem to see the module because before install us the plug-in, it showed a port xg3 xg4, and after the addition of the module, it shows that these ports.

  So I have a few questions:

  Is the SFP + above compatible with this model of switch?

  If so, how can verify us that the ports are active?

  Here is the result of the port details:

  #show interface ethernet 1/xg3 in detail

  Port Type Duplex speed Neg Admin link

  A State

  -----  ------------------------------  ------  -------  ----  -----  -----

  1/xg3 10G - level s/o unknown Auto Up Down

  Port description

  ----  --------------------------------------------------------------------------

  1/xg3

  Flow control: enabled

  Port: 1/xg3

  Belonging to a VLAN: access mode Mode

  Operating parameters:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Default priority: 0

  GVRP status: Disabled

  Protected: disabled

  -Other - or ITU (q)

  Port 1/xg3 is a member of:

  Rule of VLAN name evacuation Type

  ----    --------------------------------- -----------   --------

  1 by default not marked by default

  Static configuration:

  PVID: 1

  Capture filtering: enabled

  Acceptable frame type: no label

  Port 1/xg3 is configured statically:

  Output name rule of VLAN

  ----    --------------------------------- -----------

  Prohibition of VLAN:

  Name of VLAN

  ----    ---------------------------------

  Port 1/xg3 Enabled

  Status: Disabled role: disabled

  -Other - or ITU (q)

  Identification of the port: 128.51 shipping cost: 0

  Fast port: No. (configured: no) root Protection: No.

  Designated the bridge priority: 32768 address: 80:00:00:25:64:19:92:1 C

  Identification of the designated port: 0.0 cost of access road designated: 0

  Root regional CSE: 80:00:00:25:64:19:92:1 C CSE Port cost: 0

  BPDU: 0 sent, received 0

  Yes, this module is listed as compatible with the switch. It seems that you install in Bay 2? He may have listed these ports but they probably do not appear as active. Have you tried to make a connection with ports?

• Connection SAN Dell PowerConnect 6248

  Our switch in our network is the Dell PowerConnect 6248. This switch has a SFP module.

  I was wondering if I could use this module to connect my SAN [activeRAID 32 TB of storage active destocking] and have access to the storage as a network or NAS drive Bay.

  To be more precise I'll be plugging the controller [HBA] San to the SFP module on the 624 of Dell PC via a cable Fibre Channel LC.

  I'm new to SAN configuration and look for the best solution to access the storage on my network.

  Everyone has implemented a San with the SFP Module before; If that set up your look like?

  Fibre channel and ethernet/IP are not compatible protocols without another device that can translate. The 6248 has no support for FCoE. There are switches that support both they are called network switches convergent or unified, although generally the traffic is still separated.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• Can not activate WLAN with FN + F8 in windows Vista

  Cannot activate WLAN with FN + F8 in windows Vista.
  I installed the driver from the driver page and I installed the update to the bios but it doesn t work.

  Ty

  In a first time, you must activate WLAN using the WLAN switch (the small orange LED will be ON). Check it out!

• VMware Distributed Switch with VLAN

  Hi again,

  A lot of work with VLAN now.

  But just a quick Questions. Is there a documentation or HowTo Guides how to set up vSphare VMware Distributed Switch with several VLANS on a Switch GS724Tv4?

  

  But soon, I try to add a host or network, it is empty.

  This is probably an easy problem of VMware, but I try here first to see if someone has document guide HowTo so I can start with.

  Thank you

  Christian

  Never mind about this,

  I found the problem on my own, but perhaps a documentation would be great to have. But it's a good start to have the right license of VMware, before you start.

  * I was just out of luck when I thought *.

  / Christian

• Mac pro with monitor Dell P2414H book: how to rotate the image displayed in mode portrait when I rotate the monitor 90 degrees

  I have a mac book pro retina bought in 2014 which I use with a Dell P2414H monitor.

  I bought this monitor because it can turn up to the vertical position ('portrait'), but when I do that the image of the screen does not turn with it.

  I called Dell and they said that it is a problem to solve with Apple.

  Does anyone else have this problem? and it got fixed?

  This is the Office Mac Pro forum. I asked that your post be moved to the MacBook Pro laptop forum.

• Dell Inspiron 531 is not communicating with the Dell AIO 926 Photo printer.

  Dell Inspiron 531 is not communicating with the Dell AIO 926 Photo printer.  Maintains documents in the print queue and print them when the computer is restarted.  In addition, the computer does not recognize my Promaster digital converter when I plug it into a port.

  Hello

  Thanks for posting in the Microsoft Community Forum, please be assured that we would do our best to help you.

  Please answer the following questions that would help us provide a better solution.

  What version of Windows are you using?

  Try to follow the steps and check:

  Step 1:

  Visit the link following if you are using Windows 7.

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  If you are using Windows Vista, see the steps mentioned in the link.

  http://Windows.Microsoft.com/is-is/Windows-Vista/troubleshoot-printer-problems

  Try the steps from the link following if you are using Windows XP.

  Resources for the resolution of the printer in Windows XP problems

  http://support.Microsoft.com/kb/308028

  Step 2:

  Try to activate the devices associated with the Dell printer and disable the rest by performing the clean boot, once done try to print.

  You can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts. The following article explains how to solve problems in Windows Vista or Windows 7 by performing a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: Put the normal computer as mentioned in step 7 of section.

  Step 3:

  About the issue with Promaster digital converter try to connect to another USB device or run the fixit and check:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Please feel free to respond if you have any other questions, we would be happy to help.

• Lexmark Z705 printer does not not with my Dell XP Home Edition.

  Original title: help with printer

  I have a Lexmark Z705 printer.  He worked with my Dell XP Home Edition, but now it will not print.  It seems that I need gyo8olo maxtor.  I lost my

  Restore disk.  Where I can down load this?

  Hello
  1 did you change on your computer before this problem?
  2. you receive an error message?
  Follow the suggestions and then check out.
  Method 1

  You can install the drivers from the link below. http://support.Lexmark.com/index?locale=en&ProductCode=LEXMARK_Z705&UserLocale=en_US&segment=download&OS=WINDOWS_XP&page=downloadsList&oslocale=en_US

  Method 2
  You can follow the procedure in the article.
  Resources for the resolution of the printer in Windows XP problems
  http://support.Microsoft.com/kb/308028/en-us

  Method 3
  You can follow the procedure in the article.
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  I can't connect to the network wirelessly with my Dell INSPIRON laptop because I get the automatic Wireless Configuration error, see Article 871122

  Try this below and see if it help you.

  http://support.Microsoft.com/kb/871122

• If I can reinstall XP pro on a 'white box' PC using a disk with a Dell or HP? I have my product key. If I can't, then what?

  My 'white box' PC is all buggy after a lot of use, and I want to start with a reinstall.  I have my product key XP Pro but no media.  Can I use a disc that came with a Dell, HP or other PC manufacturer?  The steps, what are my options.

  Thanks for responding.

  No, you cannot use your support Dell/HP OEM to install XP on a generic computer built. Installation media more computers brand is locked in BIOS for motherboard of that OEM (Dells are). In addition, most HPs have just a recovery disc and not a real disk operating system. As for using the product key you have, it's from the CD that you used initially install XP on the generic construction machine? If so, will need you a corresponding version installation CD; namely the retail Home/Pro/MCE or generic OEM Home/Pro/MCE.

  If it were a copy retail:
  How to replace lost, broken, or Missing Microsoft Software or Hardware - http://support.microsoft.com/default.aspx?scid=KB;en-us;326246
  MS - MVP - Elephant Boy computers - don't panic!

• The Dell printer cannot communicate with the Dell computer.

  It seems that suddenly my Dell AIO 942 printer cannot communicate with my Dell Studio 17computer.  These devices have been the transparent connection until two days ago.  I've set up a restore point, I installed the drivers, unplugged and re plugged 110 s and USBs, used different ports and I still have the same, printer cannot communicate with the State of the computer.   Copy and scan functions are good, Windows Vista operating systems.  How can I find these devices to their previous state of communication?

  Jesse,

  Thank you very much for the detailed information. It really give us a head start trying to solve the problem.

  Please answer these questions to get more clarity-

  (1) what are the other steps in troubleshooting tried by you so far?

  (2) other changes on the computer that I should know about?

  In the meantime, I have you refer to items offered on the Dell website - troubleshooting

  http://www.Dell.com/support/home/us/en/19/product-support/product/Dell-942/research

  You can also have a look at the Microsoft article as well-

  http://Windows.Microsoft.com/en-in/Windows/printer-problems-in-Windows-help#fix-printer-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Get back to us with the results.

• Problem with the Dell Dock shortcuts

  I put a shortcut on my Dell dock some time ago, since then I deleted and added another shortcut to replace. Whenever I restart the computer, the old shortcut is back and my new must reset again. I tried the lock settings, but it always comes back to the old shortcuts on each reboot. How can I get the dock to hold its changed settings?

  Hello

  Willl you must contact Dell about this, because they provide you with the Dell Dock.

  Try asking their Support forums.

  http://en.community.Dell.com/support-forums/default.aspx

  See you soon.

• My Dell Vostro 1310 won't start. I turn it on and the black screen with the Dell logo appears and nothing more

  It was working fine and accidentally my phone fell on the keyboard and the computer froze. There was a part of the image of what was on the screen before that happened and blue and red lines/markings or whatever it is. I unplugged and took out the battery. When I turned on it again, the black screen with the Dell logo comes up and just stays there. What should I do?

  Hello

  If under warranty contact Dell

  http://support.Dell.com/

  or ask in the forums Support of Dell

  http://en.community.Dell.com/support-forums/default.aspx

  If it is under warranty, contact a reputable repairman, local computer

• I get a screen blue with the Dell logo on it and no office mouse pointer or even. __

  Remember - this

  Only, I get a screen blue with the Dell logo on it and no office mouse pointer or even.

  is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Check with Dell to see if there is a disc of diagnosis of material that you can download or order for your computer to test and see why it is not booting.  Also check the LEDs on the front that can display a code error, or for a series of beeps which may indicate an error code.

  "Arlingtonal" wrote in the new message: * e-mail address is removed from the privacy... *

  * Remember - this *.

  I get a screen blue with the Dell logo on it and no office or even the mouse pointer.*

  is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  * You have problems with programs
  * Error messages
  * These recent changes made to your computer
  * What have you tried to solve the problem