Have a HP Officejet Pro 8000 printer. Had magenta streaks.

Similar Questions

• OfficeJet pro 8000: Officejet pro 8000 prints the part of the document

  Have a problem with both networking Officejet pro 8000's. If you print a paginated document 4, printing two pages and stops, then 2 minutes he feeds a white sheet of paper in the printer, the printer hangs then error light on, who need to power cycle to restart. The network is in a school, unused printers for a few weeks, before now, they both work as it should.

  This problem is with a laptop with free Wi - Fi. However, even 4-page document sent to another that officejet pro 8000 prints as it should, and prints as it should when sent to a photocopier.

  The network of small schools there are ten computers wired to office, after trying to print from one of them, the same problem occurs with 2 of 4 pages printing, then a white sheet, then the printer hangs. This desktop computer will also print the same document on the photocopier without problem.

  Not very well where to go with this, help please!

  Problem solved, simply wanted the new cartridges!, but what I do not understand why the part of a document of four pages would be absolutely fine print, all the colors print as they should, then stop and hang. Power cycle printer, exactly the same result. Exactly the same on both 8000 printers?

• HP Officejet Pro 8000 printer range makes the vertical white lines

  My HP Officejet Pro 8000 printer makes white vertical lines around text and photos.  What can I do?  I use Windows 7.  As far as I can see, the print heads don't need to be changed. Cleaning them would help? If so, how can I clean them? Thank you.

  Hello

  You can try the steps listed in this document:

  Troubleshooting print quality problems

  Let me know if it helps

• HP Officejet Pro 8000 printer - A809a. Drivers not installed

  I have a wonderful printer HP Officejet Pro 8000 - A809a used exclusively as a network printer and works PERFECTLY. Yet, I have errors reported about drivers not installed in device (Windows 7, 64 bit Ultimate) Manager.

  These are:

  1] adapter Multifunction (x 1)

  -Officejet Pro 8000 a809

  The drivers for this device are not installed. (Code 28)

  There is no driver selected for the item or a set of device information.

  To find a driver for this device, click Update driver.

  AFTER DRIVER SEARCH:

  Windows could not find a driver for your device

  Try to use the drivers of "OJP8000vA809_Basic_14.exe" has been a failure.

  2 other devices (x 1)

  Same as above.

  [3] printers (3 entries)

  -HP Officejet Pro 8000 A809 Series. (This is the only good entry)

  Properties:

  The device is functioning properly.

  -b. Officejet Pro 8000 A809.

  Properties:

  The drivers for this device are not installed. (Code 28)

  There is no driver selected for the item or a set of device information.

  To find a driver for this device, click Update driver.

  AFTER DRIVER SEARCH:

  Windows could not find a driver for your device

  Try to use the drivers of "OJP8000vA809_Basic_14.exe" has been a failure.

  -c. Officejet Pro 8000 A809.

  Properties:

  As above.

  Disabling or even uninstall these additional entries have no effect on the function of network printer.

  BUT they continue to be replaced after the reboot.

  This situation will affect the perfornce of the computer.

  Any suggestions, please?

  Advance thanks.

  Thanks for the great instructions.

  Now I'm showing only a single instance of the printer asking for drivers multifunction adapter in Device Manager. Therefore, I uninstall and long and shows no return once again.

  One thing FO, this printer is not actually a multifunction type.

  The system is currently NOT error display or ask drivers.

  I'm hopping it will stay like that.

• OfficeJet Pro 8000 prints multiple pages of the same document

  Info:

  HP Officejet Pro 8000 A809a

  Windows 7 Pro 64-bit

  Last driver and firmware from HP

  When a job is sent to the printer (web, Word, Acrobat, etc.) the printer keeps printing multiple pages of the document.  Sometimes it will print the first page and a second partial page, then it reprinted again and stop at the same place on the partial page.  She does over and over again.  I ran the HP Diagnostic Utility and it was impossible to print a test page, even after turning the power on power off, then on.   Any suggestions, or is * another * bad printer?  The first was sent and replaced, so I think that this model is just a lemon.

  Thanks for the suggestion, but it didn't work.  I tried to reinstall the driver altogether package three times with no result.  I ran the utility programs that supposedly allows you to solve problems, but public services could not even to generate a test page.

  It seems that I finally found a solution, however.  I installed an older driver for MS Vista 64-bit, and that seemed to do the trick.

• inside printing with HP Officejet Pro 8000 prints pages out of order

  When you print a 3 page document with my printer HP Officejet Pro A809a print 'two-sided' setting, it prints page 1 to page 3 on the back, then page 2 on a separate sheet. How can I get the printer to print documents duplex in good condition?

  Hello

  You can check the printing preferences and duplex settings, see if you can change the order in this way.

  Set printing preferences and print

  1. In the menu file printing program, click print .

• HP OfficeJet Pro 8000: No power to my HP OfficeJet Pro 8000 printer

  I was outside for a few days and when I came home had no power light.   Our power went out briefly while I was gone.     It is not connected to a surge protector.

  Hi @Dewey43,
  
  Welcome to the Forums of HP Support! It's a good place to find the help you need, other users, HP experts and other support staff. I understand that you have a problem with the printer turns is not on. I'll be happy to help you.

  Please follow the steps of the printer is not turned on.

  Please keep me informed of the progress of things.

  If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution.
  To simply say thank you, click the Thumbs up below!

  Thank you.

• My HP Officejet Pro 8000 printer will frequently offline.

  I have an IMAC OSX Lion operating system (10.7.4).  The HP printer utility says the printer is offline and disconnected. It seems to verify that the printer itself doesn't have a light indicating power is on.  However, I checked the connections carefully to the printer and the power source and everything is properly connected.  Although the printer is wireless, I've never used this way it is connected with a USB cable.  Need help to make online...

  CONGRATULATIONS...

• OfficeJet Pro 8000 print head

  Print head cartridge and start buttons falsh button all at the same time and momentarily. Following aid online - electric disconnection for 5 minutes and turn it on again and hold the resume button when the lid is open I just can't get the cart of the printhead to move his right hand positioning in the middle to remove and clean the print head. What is the solution to this you problem? Is there another way to reset the printer?

  Hi @Steve150951,

  Welcome to the HP Forums!

  While doing some research, it is essentially the only way to get the impression transport move above. You can try to disconnect again, press on and hold the power button on the printer for at least 10 seconds (it drains any excess power it can hold) and then try again.

  If it still does not move, the transport can be taken on something or something could be taken in this regard. This stall Transport document may help in getting it to move as it will advise where to check for jams/obstructions.

  I would like to know how it goes for you

• HP OfficeJet Pro 8000 Wireless: Can I get some help here? Yellow ink will not print - HP OfficeJet Pro 8000 Wireless

  No matter what I do, ink yellow does not print, or stops at halfway printing on the page. I use genuine HP cartridges. There is a lot of ink - in fact, I just installed a new cartridge in the case where a previous (almost complete) was defective. No change. The pipe is not pinched. I flashed the firmware more recent and installed all drivers and utilities updated. I have cleaned the print heads over and over again and even took and cleaned according to the instructions.

  I think it was a sign that the printer is worn EXCEPT - just a few months ago, magenta and black stopped printing. These are the opposite printheads. When I uninstalled every bit of HP software I could find, the printer back to normal!

  The only thing I did not - it is the HP Toolbox argues that it is impossible to establish two-way communication with the printer. The patches for this involve get under the desk to play with the power cord and USB cable (even if it is a wireless printer), and my arthritic knees that make a very delicate operation. Two-way communication IS enabled.

  I'm about to start crying. I fought with this market a week, when the yellow all of a sudden went - once again, * most * of the time, but sometimes it prints to maybe an inch of the image before disappearing. Help!

  Hi @Echo2,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you use a HP Officejet Pro 8000 printer with a Windows 7 computer and all of a sudden is not printing yellow ink. I would like to help with that.

  Here is a document of support for the print quality problems - Troubleshooting print quality problems.

  Please let me know if that solves the problem, or if you need assistance.

• HP Officejet Pro 8000: HP Officejet Pro 8000 installation CD

  Hello Forum,

  I recently had to fix my printer. Since I reconnected it it I lost my ability to print network for my laptop. The printer is connected to my turn, and it prints fine from there. I tried loading installation / setup CD to join the process of network connectivity, but (I guess since many updates of Windows 7 because I bought the printer & my system) all I get is the error message. "The operating system on this computer is not supported - current operating system: 601.64.

  Does anyone know how to reconnect my network printing capability without using the CD "Setup / Install? Y at - it an update of the CD (software download) that I can use to run the option of network connectivity?

  Thank you!

  Hi @djpprint,

  Welcome to the Forums of HP Support! I see that you are interested the connection to your network without wire of your HP Officejet 8000.

  Please start here: Setup the printer to a wired or wireless network for the HP Officejet Pro 8000 Printer Series

  I will also leave the link software and driver for the 8000 Jo:

  Driver and HP Officejet Full Feature software

  I hope this helps!

  Let me know the results. If this resolves the problem please let others know to mark this message as "accept as Solution".  To simply say thank you, click the "Thumbs up" below!   If you need more assistance let me know and I will gladly do everything I can to help.

• OfficeJet Pro 8100e Printer Wizard not available

  Hello

  Have installed new Officejet Pro 8100e printer under Windows 7, 64 bit professional and it prints well, but, when I double click on the printer icon in the "Devices and printers" to bring up the window that has the HP printer Assistant inside...

  The printer HP Assistant does not at all.

  I have therefore no access to printer management tools.

  I was wondering about the software on the installation CD, so I uninstalled and reinstalled via download from the website support - same result.

  Someone else had this problem?

  Anyone who has a solution?

  Grateful for any help...

  Hello

  What happens when you click on start < programs=""> HP, select the folder for your printer, then the HP software? (Listed under the printer model)

  Any specific answer?

  If the software does not work, try to run this fix and check any changes:

  http://support.HP.com/us-en/document/c03640384

  Note: Although the details of the list of the different behaviors I belive it can also help for the problem described

• Power supply for Officejet Pro 8000

  I got HP Officejet Pro 8000 Printer - A809a (CB092A) that has no power cord supply or any adapter/power supply that would pass an electrical outlet at the rear of the printer. What do I need? Where can I buy / them? Thank you.

  power cord: 8121-0895

  power supply: 0957-2262

  order of:

  PartSurfer.HP.com

• HP Officejet Pro 8000 - guard alignment page printing

  I had trouble with black ink print does not correctly so after several cleanings I decieded to manually clean the print head. I took the printhead of the printer then whipped cream, the part where the ink comes out with a most paper towle. After that I put the print head in the printer prints a print alignment page. Ok. Now, every time I have print whatever it is that the printer will be after the print job is printing another page of alignment. Is there a way to stop? Thanks for your help.

  Hello TheDeerSlayer,

  When you clean the print heads, you should try to not clean the part where ink is coming out of it (nozzles). It is very easy to damage them and if it happened, most likely the only way to solve the problem is to replace the print head. There are two things, you might try to see if you can get the print head working properly again: first thing is to clean the sensor that checks the nozzles. It is located on the right side of the printer at the bottom of the area in which the cart moves, it looks like a strip of metal which is only visible when the transport is located on the side more to the right of the printer. Be sure to use a cloth moistened with cold water. What you might try if this does not solve the problem and the nozzles are just clogged with ink and not really damaged, is to heat water (almost boiling point) and then soak the part of the printhead whith the nozzles in the water for some time. Let the printhead to dry and then install again and see if it works now.

  This picture is of you can location of the sensor that checks the print head nozzles. The image is not so great and is an another printer, but it is located in the same place on Officejet Pro 8000.

  

• OfficeJet Pro 8000 - is no longer prints borderless print after upgrade - Tiger for the Mac Snow Leopard

  Mac OS X 10.6.8

  HP Officejet pro 8000 A809

  Wireless

  HP Photosmart Studio v. 9.7.4

  After upgrading from Tiger to Snow Leopard I lost the ability to print without MARGINS - until that time, that I had no problem.

  I use HP Photosmart Studio to print, but get the same error every time: "the selected printer supports the paperwork without borders. If you print, will serve the maximum printable area of the current paper size.

  I downloaded the most current driver after that I improved and I was able to print in general - when I try to select borderless printing it tells me that this printer does not support. I was able to print without margins using Creative Suite Indesign and printing of this app--but have lost the functionality of the HP Photosmart Studio is really a drag - since I have to do all sorts of adjustments to do workaround printing.

  Is it possible to upgrade Photosmart Studio? or re-start it? I'm lost and need help.

  Thank you

  If you always reminants of the HP software meant for 10.4, you must uninstall the software by using the "scrubber".  If you have already uninstalled, reinstall from the CD, then:

  Go to Applications/Hewlett Packard / click Uninstall HP
  Click on continue
  Highlight your device in the left pane
  Hold down the Ctrl and Opt Cmd and click on uninstall< scrubber="">
  There will be a pop up that asks if you are sure you want to uninstall all hp software. (At this point, if you continue, all HP printers you have installed will need to be reinstalled)
  Click on continue and let it finish

  Restart your Mac

  Now run a software update.

  Finally, download and install the "Full Featured" driver and software from the "Support & drivers" link at the top of this page.