Health Plugin HCL vSAN

Similar Questions

• vSAN + health plugin = work not correctly WebClient

  Colleagues, after the installation of plugin vSAN health (VMware-vsan-health - 6.0.1.2940255) WebClient does not work missing from the interface all the shares, off virtual machines are displayed. It is useful only remove plugin et Restart vserver. Any thoughts?

  System: vServer 6.0.0 - 2800571, esxi 6.0.0 - 2809209

  I had the same problem on the Windows version of vCenter.  You must launch a prompt by right clicking and then run as administrator.  Then run Setup from the command prompt.  Right clicking on the file configuration, then on run as administrator does not work.  Thank you, Zach.

• vSAN health Plugin breaks Web Client

  I installed the Plugin health vSAN, and when I went to the web client to complete the host install; I was able to navigate the environment, but the middle part is... empty.  I uninstalled the plugin and web client works normally.  Has anyone else seen elsewhere?  I intend to open tomorrow a SR.  Thank you, Zach.

  I don't know if these help or not, but maybe you can check whether they make a difference.

  1. ensure that the user who installs the plugin from control of health has privileges to vCenter

  2. ensure that the installation is "run as Administrator". You may need to open a cmd with "run as Administrator" command prompt, then run the msi file.

• Problem with the installation of the Plugin to check the VSANS health

  Hello!

  After running - /usr/lib/vmware-vpx/vsan-health/health-rpm-post-install.sh

  I get this result:

  /usr/lib/VMware-VPX/VSAN-health/health-RPM-post-install.sh--force

  / usr/lib/VMware-vpx/Workflow/bin

  2015 05-15 T 21: 32:05.625Z development for install parameter: workflow.int.ser vice port

  2015 05-15 T 21: 32:05.633Z development for install parameter: workflow.int.jmx - port

  2015 05-15 T 21: 32:05.643Z development for install parameter: vpxd.int.sdk - por t

  2015 05-15 T 21: 32:05.650Z development for install parameter: vpxd.int.sdk tun nel-port

  2015 05-15 T 21: 32:05.658Z development for install parameter: rhttpproxy.ext.p ort1

  2015 05-15 T 21: 32:05.665Z development for install parameter: rhttpproxy.ext.p ort2

  {'vpxd_sdk_tunnel_port': ' 8089', 'rhttpproxy_https_port': '443', 'rhttpproxy_htt p_port': ' 80', 'workflow_service_port': ' 8088', 'vpxd_sdk_port': '8085', 'PASSWO RD': ", 'workflow_jmx_port': '19999'}

  2015 05-15 T 21: 32:05.673Z development for install parameter: syslog.ext.port

  2015 05-15 T 21: 32:05.682Z development for install parameter: vc.home.path

  2015 05-15 T 21: 32:05.690Z development for install parameter: vc.conf.path

  2015 05-15 T 21: 32:05.691Z health service firstboot VSAN has started

  2015 05-15 T 21: 32:05.702Z user %s already exists, creation to jump.

  2015 05-15 T 21: 32:05.710Z development for install parameter: rhttpproxy.cert

  2015 05-15 T 21: 32:05.710Z WARNING rhttpproxy.cert install parameters optimization I empty s

  Traceback (most recent call changed):

  File "/ usr/lib/vmware-vpx/firstboot/vsanhealth_firstboot.py", line 292, may n

  RES = vsanhealth_fb.get_rp_cert_info)

  File "/ usr/lib/vmware/site-packages/cis/firstboot.py", line 185, in get_rp_cer t_info

  digital footprint, ssl_trust, TCR = get_certinfo (rp_cert_file)

  File "/ usr/lib/vmware/site-packages/cis/tools.py", line 184, in get_certinfo

  f.readFile (cert_file)

  File "/ usr/lib/vmware/site-packages/cis/utils.py", line 1028 to readFile

  loErrMsg = localizedString (errMsg, file_name, e)

  TypeError: localizedString() takes at most 2 arguments (3 given)

  2015 05-15 T 21: 32:05.712Z health firstboot VSAN has failed

  Traceback (most recent call changed):

  File "/ usr/lib/vmware-vpx/firstboot/vsanhealth_firstboot.py", line 343, < mo dule >

  Main()

  File "/ usr/lib/vmware-vpx/firstboot/vsanhealth_firstboot.py", line 333, in may n

  If eInfo and eInfo.detail:

  UnboundLocalError: variable local "eInfo" referenced before assignment

  VMware-vpxd: your visit vpxd request administrative. process ID was 9301

  success

  VMware-vpxd: Certificate SSL VC does not exist, it will be generated by vpxd

  Pending database shipped to startup: success

  Running scripts before starting...

  VMware-vpxd: from vpxd of administrative request.

  success

  VMware-vpxd: waiting for vpxd to start listening to the requests on 8089

  Wait vpxd initialize: .the

  VMware-vpxd: vpxd has been initialized.

  Last login: Friday, May 15, 21:18:53 UTC 2015 on console

  Stopping VMware vSphere Web Client...

  Order of VMware vSphere Web Client.

  Last login: Friday, May 15, 21:32:20 UTC 2015 on pts/1

  From VMware vSphere Web Client...

  Waiting for VMware vSphere Web Client...

  running: PID:30348

  

  The suite - no buttons.

  As far as I understand it - there are a few problems with certificate.

  So, help me with troubleshooting, please.

  Thank you.

  Glad it worked! I managed to solve the rest of my problem get the plugin loaded as well.  Layout rhttpproxy.cert solved the problem with health-tr/min-post-install completed successfully.  But after you start the vmware-vsan-health service, health in the web client page loaded yet never buttons such as 'enable '.

  I checked /var/log/vmware/vsan-health/vmware-vsan-health-service.log and noticed it was spamming 'Could not open a session in VC, retry in 10 seconds' over and over again.  So I went digging in the python source in /usr/lib/vmware-vpx/vsan-health. I managed to understand that when you start the web service that hosts the plugin, it tries to connect to vCenter using own vCenter SSL certificate and the private key (rui.crt and rui.key) in/etc/vmware-vpx/ssl. On my VCSA, the permissions of that file looked like this:

  myvcsa: / etc/vmware-vpx/ssl # ls - la

  Total 28

  drwxr-x - 2 root cis 4096 Jul 20 05:00.

  drwxr-xr-x 14 root root 4096 21 Jul 04:05...

  -rw - 1 root root 3416 Apr 30 05:36 rui.crt

  -rw - 1 root root 1704 Apr 30 05:36 rui.key

  -rw - 1 root root 65 30 Apr 05:19 symkey.dat

  -rw - 1 root root 3343 Apr 30 05:36 vcsoluser.crt

  -rw - 1 root root 1704 Apr 30 05:36 vcsoluser.key

  Now, I knew that the health service was run as a local user called vsan-health. It so there's no way that he would be able to read these files.  Fortunately, I had a mostly vanilla VCSA I could compare with.  Here's what looked like the VCSA vanilla folder:

  myvcsa: / etc/vmware-vpx/ssl # ls - la

  Total 28

  drwxr-x - 2 root cis 4096 Jul 20 05:00.

  drwxr-xr-x 14 root root 4096 Jul 21 04:24...

  -rw - r - 1 root cis 3416 Apr 30 05:36 rui.crt

  -rw - r - 1 root cis 1704 Apr 30 05:36 rui.key

  -rw - 1 root root 65 30 Apr 05:19 symkey.dat

  -rw - r - 1 root cis 3343 Apr 30 05:36 vcsoluser.crt

  -rw - r - 1 root cis 1704 Apr 30 05:36 vcsoluser.key

  Notice the difference of the Group property on the associated files cert and change of 600 to 640 permissions.  When I saw that, I have also remembered seeing in the vsan firstboot script that the vsan-health user was added to the cis group.  As soon as I did my broken VCSA permissions corresponds to vanilla, the service has started and all this work began.  I guess the reason that my permissions were leech is a bug with the replacement of SSL scripts.  One of the first things I do on my vCenter is updating the SSL certificates with those customized PKI infrastructure.  I guess that process currently does not work quite right and live the permissions on files that is not replaced.

• SAN health service virtual VMWare

  Hello

  Any who stumbled upon this question. We are in the process of updating the vcenter 6.0 to 6.0U1. During the upgrade Setup attempted to stop vsan-health service that didn't exist, and the upgrade has been abandoned. I try to install the plugin from vsan, the installation was successful, but the windows service has not been registered. Here is the log of errors and hope that someone can help me to resume the service.

  '"D:\Program Files\VMware\vCenter Server\vpxd\scripts" ' is not recognized as internal or external, command an executable program or batch file. "= VMWare Virtual SAN Health Service installed = '.

  Thanks in advance

  Found fixed the name of the VMWARE_PYTHON_BIN variable doesn't have the full path to: \Program Files\VMware\vCenter Server\python\python.exe

• Impossible to clone virtual machines to VSAN datastore

  Hi all

  Whenever we try to clone a virtual machine using vCenter vSAN not store data to the vSAN data store fails with the following error.

  File /vmfs/volumes/540024e7-2d8bb59e-0bef-40a8f0305c2c/blr7-dhcp-1/***.vmdk not found.

  It is a cluster of vSAN 3 node with 1 * 2 SSD * magnetic disk by the configuration of the node.

  ! 0 gig uplink connected to vDS with one vlan separate tag group of ports (Distributed Switch). Multicast IGMP snooping is enabled on the VIRTUAL LAN that is used for the VTEP.

  Storage strategy is: tolerate 1, band 3, 70% cache read

  Storage strategy using 3-band

  Cluster shows also in good health

  ~ # esxcli vsan cluster get

  Cluster information

  Enabled: true

  Current local time: 2015-01 - 05 T 14: 33:05Z

  Local node UUID: 54a7b9fa-afde-3f59-1d67-40a8f0305c2c

  State of the local node: BACKUP

  Health status of local node: HEALTHY

  Cluster under master UUID: 53e07d1e-4154-1e32-1cc6-40a8f0305c68

  Cluster under backup UUID: 54a7b9fa-afde-3f59-1d67-40a8f0305c2c

  Cluster under UUID: 5276ec11-3024-d7e5-6696-cb2b47017814

  Cluster under membership entry revision: 2

  Subgroup Member UUID: 53e07d1e-4154-1e32-1cc6-40a8f0305c68, 54a7b9fa-afde-3f59-1 d 67-40a8f0305c2c, 54a6abf6-9350-0741-2815-40a8f030f494

  Under Cluster Membership UUID: 9f6eaa54-5573-d61e-d26f-40a8f0305c68

  ~ network vsan # esxcli list

  Interface

  VmkNic name: vmk3

  IP Protocol: IPv4

  Interface UUID: 1f6ca254-337e-9641-1c50-40a8f0305c68

  Agent group multicast address: 224.2.3.4

  Agent Group Multicast Port: 23451

  Multicast Address Group Master: 224.1.2.3

  Master Group Multicast Port: 12345

  Multicast TTL: 5

  ~ # esxcli network ip connection list | egrep 224

  UDP 0 0 224.1.2.3:12345 0.0.0.0:0 34586 worker spend

  UDP 0 0 224.2.3.4:23451 0.0.0.0:0 34586 worker spend

  Also the deployment of the virtual machine to vSAN datastore also very slow.

  Could you please help me understand the issue.with cloning.

  With respect,

  Aju

  This post should help determine the number of hosts.

  VSAN part 25 - hosts much-needed to tolerate failures? CormacHogan.com

  The number of disks is harder once you start adding bandwidth, because you also have to take into components witness account.

  Each band will require a disc, and you increase FTT, you will need to double the number of disks you want to mirror any of the components score. And then, of course, welcome the witnesses.

• VSAN disks required for Instalation of the host

  Hi all

  I have 2 questions on VSAN

  (1) controller HP smart array is not needed that storage is VSAN handles.

  (2) the selected material can accommodate 5-disc, so if we use a disc to install ESXi5.5, can we use the remaining disk to can be used for VSAN somehow, or we have to live with for VSAN 4 drives in my case.

  Thank you

  Kapil

  you will need to have a disk controller that supports passthrough to a minimum and one from the HCL VSAN. Judging by the HCL VSAN you need a controller to purchase anyway.

• Virtual loan SAN - recommended Configurations vs HCL

  I'm on version 1.1 of the document, it shows a R280 Dell that is not on the HCL VSAN and it includes SuperMicro which is not on the HCL.  It doesn't have the Dell R720, the R720xd and the T620 appearing in the HCL.  How to solve these two?

  [email protected] wrote:

  Correct,

  Duncan - Thanks for the reply.   I was concerned by some servers which have been listed in one place, not both.

  Wade spoke last week and he strives to address this problem in a reasonable amount of time, it is indeed not ideal.

• H730 driver from the Vmware Vsphere 6.0 site?

  I have a cluster with VSAN work, but the Virtual SAN Health plugin gives a warning under virtual health SAN HCL-> controller driver, which the driver used is slightly different from what is on the HCL.  I used ISO customized for VSAN/VMware on Dell website, and this is the only warning gives the plugin.  I would like to specifically install the correct version in the HCL.

  So, I have the found for download on the firmware version PERC H730/H730P/H830 Mini/adapter RAID controllers 25.2.1.0037 Driver Details | Reference Dell U.S., but it does not list a download for VMware, only windows and linux. I see it in the VMware HCL to http://www.vmware.com/resources/compatibility/detail.php?deviceCategory=vsanio & productid = 34853 & vcl = true, where he lists a download for Vsphere 5.5 and 6.0.  How I would deploy for my 6.0 cluster?  Do I need to use the Windows driver from the Dell website and deploy with OME?  I prefer to get it on the VMware site.   I looking in the wrong place on the vmware site?

  Not sure if this is relevant, but the Dell OEM ESXi image has been mentioned.  With VSANs, it is recommended to avoid the OEM images and use the image of VMware stock.  Thank you, Zach.

  VSAN and OEM ESXi ISO images | CormacHogan.com

• multicast performance test?

  I'm curious to know what kind of bandwidth, you get performance multicast vSAN health plugin test. Now our vSAN is on a link of 1 G (will modernize it to 10G thereafter), I get only about 80 M/s compared to the desired bandwidth 125 M/s, I was wondering what could be done to improve it. It is a facility newly vSAN and no other traffic at all the.

  We use Dell N4032 switch, the current configuration of the network's MTU 9000, with active igmp snooping and quierer address configured as the IP of the interface VLAN switch, seems she works as assumed:

  show ip igmp snooping groups

  Group VLAN journalist IIR filter address Source

  ---- ------------------ ----------------- ------- --------- ---------------

  95 224.1.2.3 192.168.51.11 exclude Te1/0/2

  95 224.2.3.4 192.168.51.11 exclude Te1/0/2

  95 239.255.255.253 192.168.51.11 exclude Te1/0/2

  95 224.2.3.4 192.168.51.12 exclude Te1/0/4

  95 239.255.255.253 192.168.51.12 exclude Te1/0/4

  95 224.1.2.3 192.168.51.13 exclude Te1/0/6

  95 224.2.3.4 192.168.51.13 exclude Te1/0/6

  95 239.255.255.253 192.168.51.13 exclude Te1/0/6

  95 224.2.3.4 192.168.51.14 exclude Te1/0/8

  95 239.255.255.253 192.168.51.14 exclude Te1/0/8

  I also tried to disable igmp monitoring on this vlan, makes no difference on the performance of multicat test.

  It's true. In fact, we put the limitation/performance target of network multicast as 1000 M/bits during the test, the desired line speed is 1000 * 1024 * 2/8 = 125 M/B. As long as bandwidth real is greater than 50 M/B, we consider the NECK.

• VSAN health check failed

  VSAN health says that my megaraid driver isn't in hcl, but the version of the driver showed in the health check is the same as the hcl on the vmware web site.

  My driver version is 6.603.55.00.1vmw.

  I also download a driver of async partner of vmware, and it still does not pass the health check.

  Where can I get the right driver?

  You can try these instructions to get the file offline of HCL

  How to download VSAN HCL of VSAN Health Check Plugin offline files? virtuallyGhetto

• vSAN mini Dell H730 after update02 health

  Hello.

  I have 3 servers based on Dell H730mini. After the upgrade to esxi update02 vSAN was broke (because they were old drivers for the RAID).

  I have excluded all the vmware cluster servers, updated RAID drivers on compatible. After I created a new server cluster and it contains. Everything works.

  However, vSAN health module indicates the error type: "correct version of installed virtual san health invalid query. Relocation of vib module on each server correctly (not work), but in the cluster, all the information indicated the same version "in ESX 0.0.

  ESXi 6.0.0 38255889

  Vserver 6.0.03339083

  Any ideas?

  Hello, it seems to me that you must update vCenter.  Who is on the last version?  Thank you, Zach.

• VSAN health is missing from the Web Client 6.0 GA

  Updated since U2 of 5.5 to 6.0 GA, vSphere and all hosts, vsanDatastore was entirely rebuilt on v2, all simply because I didn't have to update and had swing available storage. I was looking at this post and there should be a component of health listed, but I'm not on my own. Have you tried the usual nonsense to reboot the vCenter, but do not know what other direction to go.

  

  http://blogs.VMware.com/vSphere/2015/02/virtual-San-60.html

  ↑ This article has an image with health shown, do not know what happened here.

  This feature is not yet available.

  It will be released as a plugin for vCenter very soon.

  We will make announcements in several places when it becomes available.

  Sorry if the blog has been confusing.

• VSAN 6.0 HCL

  The HCL page does not seem to be updated for 6.0 VSAN. I guess that she will support a bunch of new material?

  Are there other ways to find out what it is, or is the update of the HCL page just around the corner?

  If you look at our VMware Compatibility Guide: vsan we posted this info

  wait until it is available for March 18, 2015

  Virtual SAN Compatibility Guide is currently upgraded to new hardware support (I/O controllers, hard drives and SSD) and prepared knots. Hardware and components ready in nodes supported by Virtual SAN 6.0 will be listed by 18 March 2015. In the meantime, if you have any questions of compatibility of equipment for Virtual SAN 6.0, please contact [email protected]

• vCenter 5.1U1 y health-ui plugins y cim - ui than no pull

  Buenas,

  Estoy realizando una instalacion vCenter 5.1 U1 UN cero y Peel than tras instalacion los plugins "vCenter Service status" is "vCenter material status" appears deshabilitados indicandome:

  The following error occurred during the download of the plugin script of https://vCenter:8443/health-ui/scriptConfig.xml: The client couldn't send a request to the server (Se ha terminado the conexion: error unexpected envio)

  The following error occurred during the download of the plugin script of https://vCenter:8443/cim-ui/scriptConfig.xml: The client couldn't send a request to the server (Se ha terminado the conexion: error unexpected envio)

  En the URL don't me el del FQDN vCenter, sino el corto number appears. El servidor are UN WS2008R2 x 64 y he estado UN rato en toquetear los ficheros del tomact playing y demas pero sin exito.

  A the sounds of what could ser alguien?

  Saludos thanks.

  Buenas. Finally plug-ins los no pueden ser arrancados desde a vSphere Client wont en Windows XP. ESE era el problema...

  Saludos.