Health status power warning...

Similar Questions

• Receive optical power warning - above threshold

  As we know,

  We cannot set up the optical transmit power of the SFP. However, we can check the power level of reception received by the peer through the command:

  View details transceiver interface

  However, newspapers have been showing:

  20 August 06:45:14.434: % SFF8472-5-THRESHOLD_VIOLATION: item in gi1/0/25: high power warning Rx; Running value:-1.7 dBm, threshold value:-3,0 dBm.

  Check:

  Optical alarm warn high low warn low alarm
  Receive the power threshold threshold threshold threshold
  Port (dBm) (dBm) (dBm) (dBm) (dBm)
  -------    -----------------  ----------  ---------  ---------  ---------
  Gi1/0/25-1 article, 7 + 1.0 - 3, 0 - 19.0 - 23.0

  This will have a big impact on my switch? In particular the SFP

  Factors such as damage, etc.

  In addition, how will this affect the performance network, health and functioning of my devices

  Your ideas are much appreciated (and if you can back it up with docs, it would be useful also! ^_^)

  It seems that your remote line is the sending of a relatively high output power and/or you have a connection very short fiber with very little loss. Since you are only at the beach 'warning', you are not likely to damage any of the SFP receiver or adversely affect the operation of the network.  You don't have the possibility to add an Optical Attenuator on the link to make the action more within the specification range.

• ? Primary Master Hard Disk S.M.A.R.T. Bad Status. WARNING: Return immediately-up your data and replace your hard drive.

  When I start my computer, an error page appears. At the bottom of the page it says, "Primary Master Hard Disk S.M.A.R.T. Status Bad." WARNING: Return immediately-up your data and replace your hard drive. Press F1 for Setup, F2 to continue"I was just pressing F2 and then it starts normally, but whenever I start my computer, the same page comes up.

  Is this serious or it could be something minor? Do you have any suggestions? What does that mean? What should I do? I followed some information in the forums of someone who has had the same problem and finally, they fixed them, they said that when they made a prior microsoft update what they where missing a Parcer.

  Note: I tried to save my data before, but something goes wrong and the backup will not be completed.

  You can download the program for diagnotics HUtil Samsung http://www.samsung.com/global/business/hdd/support/downloads/Hutil210_iso_for_CDROM_drive.zip

  It's an ISO image then unzip the file and write the ISO image to a CD.

  Then restart the PC and booting with the CD. To do this, you must change the priority/boot order in the BIOS to boot from the CD first.

  Once you have started the program HUtil it will detect your hard drive Samsung. Select the hard disk.

  Enter the main Menu on the tool. Go into the menu of the tool and enter Auto diagnosis. Enable diagnostics to run, once done it will ask you if you want to perform a surface analysis - enter Yes. The analysis of surface will take some time to complete. If errors are found, it reported.

  Once more I recommend you backup your data as soon as possible, preferably before executing HUtil program.

  For more information on the program of HUtil you can go here: http://www.samsung.com/global/business/hdd/support/utilities/Support_HUTIL.html

  Write when the cache is enabled: when data are written back to the hard drive, it is written in the cache that is much faster to actually write to the hard drive. An acknowledgement of receipt is then sent by saying that the data has been written on the hard disk, when in fact it does not. In this way so that the data is actually being written to the hard drive to the rest of the system can continue to work. However memory cache is volatile, if the power goes off, the data in the cache is destroyed and if it has not been written to disk hard and yet he's lost.

  If your settings are correct. Usually the drives are configured for performance and the write cache is enabled. While flash drives and memory cards are configured for the fast-moving and write cache is disabled.

  If you want to learn more about this: http://www.pcguide.com/ref/hdd/op/cacheWrite-c.html

• Modified files HP Health Check and WARNING event ID 11 Wininit Event Viewer

  Desktop HP Pavilion p6 - 2220t - Windows 7 Home Premium 64 - bit Service Pack 1 - Microsoft Security Essentials - Windows Firewall

  I got this computer in December 2012.

  I started getting the following warning in the event viewer on the 16/09/2014:

  Log name: System

  Source: Microsoft-Windows-Wininit

  Date: 16/09/2014 14:37:12

  Event ID: 11

  Task category: no

  Level: WARNING

  Keywords:

  User: SYSTEM

  Computer: PC - 1

  Description:

  Custom dynamic link libraries are loaded for each application. The system administrator should review the list of libraries to ensure that they are linked to trusted applications.

  The event XML:

  11

  0

  3

  0

  0

  0 x 4000000000000000

  310078

  System

  PC-1

  0

  *****

  Just to be sure, I ran a full scan with Malwarebytes, SuperAntiSpyware (free version) and Microsoft Security Essentials. All had own scans with no problems found.

  *****

  Some sites on the internet suggest to get rid of this warning by setting these two keys, the default value 0, but they already are.

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Windows\AppInit_DLLs HKLM\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\Windows\AppInit_DLL

  There is nothing in the 'Data' column for these two registry keys. And there is no list of DLLS.  The string in the warning count is 0, so I don't really know what is the cause.

  *****

  I searched my drive C: for what any change to the date and time that this warning for the first time. All have been linked to HP Health Check.

  There are two components in C:\Program Files (86) \Hewlet-Packard\HP Health Check\Active Check\objects that have been modified on 16/09/2014 05:31. One was named issuelist.xml and the other XML file Config.INI.

  There are 494 items modified on 16/09/2014 14:19, all the in C:\Program Files (86) \Hewlet-Packard\HP Health Check\Guid

  The first Wininit WARNING event ID 11 logged at 16/09/2014 14:37:12. And it records now whenever I start my computer.

  *****

  These changes do not come with HP Support Assistant. Was not asked to download and install updates.  These files have been changed without my knowledge.  I did know about this until I picked up everything that has changed which could hold account of the warning I get now.

  *****

  Anyone know how to stop this warning event ID 11 registered Wininit whenever I start my computer? Someone else had changes in the HP health check recently?  Has anyone else noticed this warning of Wininit event ID 11 their recent event viewer?

  Thanks for any help and information,

  Department of public works

  Old_geekster,

  I know that this is your best advice but I really don't want to go there. Up is simple, get the programs and files on the computer; not so much.  And then there of all the bloatware to get rid again.

  Several sites indicate that this is not a problem, even if there is a list of libraries, as it has to do with the code and can be ignored as long as are listed in the DLL acknowledged regarding confidence of applications.

  At the end of my Wininit he says the warning message string is 0 and it lists all the libraries. One source suggests that it is a false alarm since no DLL is actually loaded.

  I looked for someone who had a warning Wininit where string = 0 and no list. I found this conversation: http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/custom-dynamic-link-libraries-are-being-loaded-for/80497a24-1b98-4705-93cc-32d67b5947d1

  On the second page, there is this suggestion of No.Compromise on May 24, 2010:

  "In the registry, change the value from HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Windows\LoadAppInit_DLLs from 1 to 0, restart and check if the event in question is still connected."

  (Also would check if HKLM\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\Windows\LoadAppInit_DLLs has been set to 1 and if so, change it to 0).

  Note the value to check is LoadAppInit_DLLs of type REG_DWORD, rather than LoadAppInit_DLLs of type REG_SZ. »

  May 25, 2010, he adds:

  "For the moment, it won't affect anything else, if AppInit_Dlls is empty.  LoadAppInit_Dlls is an indicator that tells Windows to "respect" (load the dll in the AppInint_DLLs) the AppInit_DLLs value.

  Older, pre-Vista apps will not know to LoadAppInit_DLLs a value of 1, so the dll they would add to this place could not be loaded.  It can be considered a good thing, because it is a quick way to get the (good and bad) code loaded into the address space of each loaded process user32.dll (practically everything), which deals with the AppInit_DLLs.

  New apps are common sense for LoadAppInit_DLLs setting so they put 1 and also add components to AppInit_DLLs.

  In your case, it seems that some program added DLLS to AppInit_DLLs, LoadAppInit_DLLs set to 1, and then the dll have been removed (manually? program cleaning? uninstall program?) AppInit_DLLs, but LoadAppInit_DLLs was restored to the default of 0 (or not being is not present at all).

  "So, our exploration indicates that Windows based the decision to record the event on"Custom Dynamic Link Libraries loading for all applications"for the LoadAppInit_DLLs parameter, regardless of the content of the AppInit_DLLs value" (it was marked as a solution but the instructions are in the post on May 24, 2010).

  I did this and the warning of Wininit disappeared.

  It worked after I changed HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Windows\LoadAppInit_DLLs, but I went ahead and changed HKLM\SOFTWARE\Wow6432Node\Microsoft\Windows NT\CurrentVersion\Windows\LoadAppInit_DLLs .

  I never changed anything in the registry before; big no no. But this person instructions and reasoning were clear enough even I could understand and it worked.

  Thank you

  Department of public works

   

• OMSE - no health status on SNMP

  I recently started an OMSE server configuration and adding OMSA servers in the environment, where I am able to create a beach discovery and set up the beach to learn about SNMP. OMSE is version 2.1.0.2635 and OMSA version 8.2. I followed the tutorial in open manage essentials to set up SNMP on 3 of 18 servers that I added to the beaches of discovery, but so far only one of them reports the status of health. 2 are on the same subnet, but in different geographic locations and a third is in another country and on a different subnet. All sites are connected by the SPLM. If I run the troubleshooting tool, 2 on the same subnet will report more information on the server with the reporting health ukd OMSE, but Dr device which is in reports from different subnet than the name of the device. Can someone help me?

  

  Hi, the DRA is the server you mentioned in your first post.

  I think it's something to do with your installation of OMSA.  I ask you to open a support on 800-945-3355 ticket. This will help our engineer to take a deeper look and possibly to fix your problem.

• 5.1 ESXI health status: unknown

  Hello

  I have a HP PL DL380p G8 and ESXI 5.1 with essential kit. Everything was ok, but after months, I got in the health configuration tab: unknown.

  Bit is all ok, server is running, and I don't find any hw problem.

  Why is-status unknown health?

  Thank you.

  Hello

  Restart management agents.

  How? Look here:

  Management for the restart ESXi (ESX 3i) agents

• vCenter 5.1 Health Status Changed alarm

  I have a vCenter server that occationally get an alarm status health (pass from green to red) changed, but I can't understand what it refers.  I've looked through the vms, hosts and plugins and can't find any other alarm that could have triggered it could cause.

  Nobody knows what he is referring?

  Thank you

  Matt

  Go-> vCenter Home-> Select health of vCenter status and see if there is anything in red or yellow

• Status of clustering and failover rises as warning - NO IP Hash offset

  Hi all

  In my lab at the House, I created a distributed switch and activated the health check. I checked and found that the grouping and health status was as unknown. Screen attached.

  

  After 3 minutes, I had an alert in the VI client to the host stating vds teaming situation of incompatibility. Attached snapshot.

  

  As I turned off the alarm that teaming and health goes unknown status to the warning. NO IP Hash mismatch. Attached snapshot.

  

  I checked all the port groups and I'm not under IP Hash on any group of ports. I rebooted services.sh but no go. I did check the vmkernel.log file, but did not find something informative. I'm under esxi 5.5 U1 and VC 5.5

  I'm running my VMware Workstation 11 environment

  Any suggestion how to solve the NO IP Hash mismatch error.

  Thank you

  Vaibhav

  Thank you for your question on my blog, sorry for the late reply.  Health check is sometimes a little weird.  VMware recommends to use to identify the problem and not constantly.  Health check is not supported with virtual load on any type of network interface cards on the platform, see:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2034795

  This includes FlexFab HP or UCS.   I assume that the virtual network adapter in my computer can also be throwing it for a loop.   I consider the following options:

  -Check your political grouping switch

  -Check to each political grouping port group

  -Ensure that none are set to the hash of the IP (for mac source based laboratory at home is your best bet or charge based on grouping)

  -If everything's not hash IP then I would turn off and on again you might find new results

  -At the end of the day the fact that you are using workstation can be the cause of the problem because ESXi hosts see a virtual network card.

  Notes on the screenshots:

  -First shot is normal, that's the message while it is still testing

  -Second and third are related to a real incompatibility or the grant in the above KB

  It's my best guess... the truth is that I've seen all kinds of crazy what with virtual cards.   I saw a situation where the health check was running a CAM table off entries (500,000) with health check the UCS... it's really bad on UCS do not use.

  It will be useful.

  Thank you

  Joseph

  blog.jgriffiths.org

• Status of disk hard not Visible in the State of health - ESX3.5i

  Hello

  Please find the attached screenshot.

  We are not able to view the status of the hard drive in the Configuration > State of health. Any comments?

  Version ESX - 3.5i

  HP Proliant DL 585 G1 - Server

  Berries - Smart Array 5i controller

  (We really are installing BMC monitoring tool and this tool does not identify hard drives).

  Concerning

  HMS

  To see the State of health of the disks and RAID configurations on a HP host, you must install CIM HP (aka offline Bundle) providers for the specific ESXi version on the host. However, I checked the HP support web site, and there's no CIM providers for the server model you are using.

  I have a HP DL380G5 and G7 host running with installed CIM providers and health status occurs when connect directly to vCenter as well as for the host.

  André

• status alert health vCenter 4.1

  Hello

  Since I've updated my high 4.0 vCenter 4.1 every time I start the server vCenter service I get this alert:

  VCENTER

  Draw the attention of

  Monitoring of health status

  This object

  2010-11-30 10:03:33

  Anyone with this problem too?

  just in case

  http://KB.VMware.com/kb/1025010

• 2.2 - ESXi - no State health of OME

  I try to get OpenManage Essentials 2.2 health of ESXi.

  A server ESXi 5.1 and OMSA 7.4 Health Watch
  Servers with 6 ESXi and 8.3 of the OMSA only show a grey question mark.

  I can find no documentation indicating which versions of ESXi and OMSA is compatible with 2.2 OME.

  I found that something was off with the OMSA package deployed via the Update Manager. It showed as being in line with the base line, but I re-uploaded VIB in the Nativity update repository, created a new base line and attached hosts. The hosts showed now also fort and OMSA installed OK.

  OME now see the health status.

  But, under Data Sources in the display of the device, the administrator of the server (storage management) and VMware ESXi have a triangle of yellow warning next to them. How will I know what is the reason for these warnings?
  

• Firefox 36.0.4 health report does not

  Report the health of Firefox does not. Does not show the start date time. This portion of the screen is empty with just a green dot.

  Please upgrade to the latest version of Firefox:

  • Update to the latest version of Firefox

  Please make sure that Firefox can establish connections to the dns names that are needed. If you open the console Web are there errors on the health status of Firefox page?

• iMac 2010 freezes, restart by only the power button

  My iMac 21 "early 2010 has been a faithful workaholic but has seen better days of course. The last six months, it was completely freeze but with the ability to move the mouse - seems to be getting more frequent. It must be restarted by pressing the power button. Usually, it's when Safari is open and above (in the current window usage), but not always. My Console is reading the following:

  Diagnostic reports to the user (at the time of the freeze)

  21/03/16 1:29:59.772 Safari [330] PM: KeychainGetICDPStatus: key :-25300

  21/03/16 1:29:59.772 Safari [330] PM: KeychainGetICDPStatus: status: power off

  21/03/16 1:30:00.583 PM WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x14a window is not attached to the window 0x14c

  21/03/16 1:30:06.301 PM Safari [330]: making closing tcp_connection_destination_handle_tls_close_notify 602 due to the TLS CLOSE_NOTIFY alert

  21/03/16 1:30:10.696 PM WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x14a window is not attached to the window 0x14c

  21/03/16 com.apple.WebKit.WebContent [365 1:30:13.570 PM]: CoreAnimation: rendering Error 502

  21/03/16 1:30:16.561 PM sandboxd [146]: com.apple.WebKit (365) ([365]) deny mach-search ATS Query Port 477 (by-pid)

  21/03/16 1:30:16.577 PM sandboxd [146]: com.apple.WebKit (365) ([365]) deny mach-search ATS Query Port 477 (by-pid)

  21/03/16 1:30:17.483 Safari [330] PM: KeychainGetICDPStatus: key :-25300

  21/03/16 1:30:17.483 Safari [330] PM: KeychainGetICDPStatus: status: power off

  Diagnostic System (at the time of the freeze) reports

  WindowServer_2016-03-21-133137_Gazzerks - iMac.userspace_watchdog_timeout.spin

  WindowServer_2016-03-21-133145_Gazzerks - iMac.userspace_watchdog_timeout.spin

  WindowServer_2016-03-21-134800_Gazzerks - iMac.wakeups_resource.diag

  The above system diagnostics are always consistent with the gel, with the exception of the following line which appears sometimes (on a former gel):

  VTEncoderXPCService_2016-03-10-075028_Gazzerks - iMac.cpu_resource.diag

  Any help in locating the problem would be greatly appreciated.

  Thank you

  Gazzerk

  If you can post a report EtreCheckon your system. We then look for obvious problems. Please click on the link, download the application and run the report. Once you have the report, please copy and paste into your response to this post.

  If you would like more information on what is EtreCheck, just click on the link and you will find a description of the application.

• Hello, I receive a message telling me that my AC power adapter type cannot be accepted.

  A few days ago, I started having a power warning message when I turn on my laptop. It is said that the AC power adapter type cannot be determined. Beacause it my battery will not charge. But it's the power adapter that came with it and I have used for so long that I got the machine. Do not know what is happening.

  I guess that the laptop works on AC power only but always?

  If you remove the battery from the laptop work?   If yes then I suspect the battery does not have rather than the power adapter.
  If it will not work without the battery then I would suspect that the adapter is faulty/defective.
  Don't let not the battery-even if it is the problem.

• The State of health critical vCenter 5.5 follow-up

  Hello

  I have a new alarm 'Critical Health Status Monitoring' and in the description, it says see vCenter Service Health in the request of the Administration, but when I go to the Administration (logged as administrator) there is no section of Health Service of vCenter . I do not see a vCenter Service Health section even being logged in as the admin. root

  Found a few suggestions to check services, but they're all on the vcenter server.

  
  

  Form what I found, seems to be on a compatible web browser and have installed the plugin for integration of customer, although it includes the same way on Google Chrome and IE 11.

  I have no way to see what is about this error, any thoughts?

  Thank you!

  Hello

  you have two options to check for this.

  1. connect to your vSphere Client and goto vCenter Service status.

  2 log in to your vSphere Web Client, open your vCenter and goto followed and Service status

  We could see if a Service is not working as it should.

  Frank