Help configuration VPN 5505
I am new to the use of Cisco devices and I need a little help with some configurations on an ASA5505 with 8.4.
I want to connect 2 ASA5505 with a site-to-site.
Site 1
is where I want to connect to. Site 1 we have access to 192.168.40.x and 192.168.42.x networks. This ip is: 192.168.40.254
Site 2
I want to connect to site 1 and see the 40.x and 42.x networks. I am able to connect to the network 40.x and can see devices on it, but I can't go to the 42.x network. This ip device is: 192.168.50.1
The sites are not in the same place, just in case someone asks about it.
Hello
Seems to me that you do not have good rules configured on Site1 and Site2 ASA on the VPN
You must add the following configurations
Site1
access extensive list ip 192.168.42.0 inside_nat0_outbound allow 255.255.255.0 192.168.50.0 255.255.255.0
access extensive list ip 192.168.42.0 outside_cryptomap allow 255.255.255.0 192.168.50.0
-It would add both traffic between networks for VPN configurations and unnated traffic through to the remote end
Site2
outside_cryptomap to access extended list ip 192.168.50.0 allow 255.255.255.0 192.168.42.0 255.255.255.0
This would add the traffic between networks for VPN configurations
Seems that you already have the NAT0 configurations in place for networks, but not above the line for the VPN itself.
Please rate if it helped
Tags: Cisco Security
Similar Questions
-
Newbie configuration VPN 5505 for client Win7
I have a client who has an installed 5505. They want VPN with their laptop Win7 but they don't want to shell out $1000 for customer VPN Cisco 10pcs.
I have correctly set up the VPN without customer and through a browser, they can get to their files, but they would map network drives is just as if they were in the office.
I tried to configure the IP Sec on 5505 and then using the built-in VPN Win7 network connection, but no go.
I do also everything through the ASDM, but I know that certain things cannot be done. I prefer to use the ASDM!
Anyone else get this set up? 99% of what I see here is how to connect the 5505 for VPN site to site.
Thank you!
Hello
To my knowledge all ASA5505 should have the ability to have 2 VPN SSL connections with the Base license. To my knowledge, this also includes using the AnyConnect SSL VPN Client (which replaces the old VPN IPsec Client software) and the VPN without customer via the Web browser.
The AnyConnect VPN Client should be available on the Flash of the ASA and is set when you configure the Client AnyConnect SSL VPN for the first time.
On the ASDM, you should be able to configure the client AnyConnect SSL VPN with the "Wizard" as any other type of VPN configuration.
The AnyConnect VPN Client is a better choice to use the old client IPsec, especially when it comes to new operating systems. The AnyConnect VPN Client can be installed in the ASA at the users computer when he or she first attempts to connect to the ASA via Web browser and connects with his credentials.
-Jouni
-
Need help to configure VPN NAT traffic to ip address external pool ASA
Hello
I need to configure vpn NAT ip address traffic external pool ASA
For example.
Apart from the ip address is 1.1.1.10
VPN traffic must be nat to 1.1.1.11
If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask.
Please, help me to solve this problem.
Thank you best regards &,.
Ramanantsoa
Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end.
Here is the configuration of NAT:
access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0
NAT (inside) 5 access list nat - vpn
Overall 5 1.1.1.11 (outside)
In addition, the ACL crypto for the tunnel from site to site should be as follows:
access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0
Hope that helps.
-
Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router
Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device.
Someone please please suggest me something as soon as POSSIBLE.
Thank you
CLI version:
ASDM and SDM Version:
-
I am interested in establishing a VPN for my computer. I looked at some of the information to help Ms. I'm missing something in the way of understanding how do or end the connection.
You can configure VPN regardless of static or dynamic IP, both are possible. You can refer to:
-
LT2P configuration vpn cisco asa with the internet machine windows/mac issue
Dear all,
I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS.
My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy
It does not work. only the resources behind the firewall, I can access. I use the extended access list
I tried also with the standard access list.
Please please suggest what error might be.
Thank you
JV
Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article:
-
Need help configuration IOS IPsec to enable communication between the VPN client
Hi, I need help with the configuration of IPsec VPN router 2811. I want to allow communication between VPN clients, is that possible? I know that ASA, you can do this by using the command "permit same-security-traffic intra-interface".
The fact is that each Client IP communicator installed, but when they tried to call each other, he failed. I guess that's because the connectivity between them is not permitted because of the VPN connection.
Thanks in advance...
Hello
Try this: -.
local pool IP 192.168.1.1 ippool 192.168.1.5
access-list 1 permit host 192.168.1.2< vpn="" ip="" addr="" of="" client="">
access-list 1 permit host 192.168.1.3< vpn="" ip="" addr="" of="" client="">
access-list 1 permit 10.10.10.0 0.0.0.255
< lan="" behind="" the="">
ISAKMP crypto client configuration group vpnclient
key cisco123
ACL 1< binding="" the="" acl="">
!
--------Done-------------
If you do NAT on the router then you might want to exempt your VPN traffic to be NAt had
Assuming that the NAT of your router is
overload of IP nat inside source list 111 interface FastEthernet1/0
!
! - The access list is used to specify which traffic
! - must be translated to the outside Internet.
access-list 111 deny ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255
Above two statements are exempt from nat traffic.
access-list 111 allow ip 10.10.10.0 0.0.0.255 any<, permits="">,>
I would like to know if it worked for you.
Concerning
M
-
Help please - configuration VPN AnyConnect crossed
Hi there, forgive me if I missed all the protocols forum because this is my first post.
I am trying to configure an AnyConnect VPN and I think it's nearly there, but not enough yet. When I connect from an outside network, it gives me the following error '... No address is available for an SVC connection. I checked the pools of addresses and what I see, they are assigned to the profile. I'm doing it also crossed, I all VPN traffic through this router... traffic LAN and remote Internet sometimes when I'm on the unfamiliar wifi hotspots. I tried to get this to work for more than 1 week with a lot of different forums to scouring. I have included my config running for anyone to help me with. I appreciate a lot of the answers to get me on the right track. Thank you.
Update 15 minutes later: I posted my SSLVPN IP pool to the DefaultWebVPNGroup and it connected but I was unable to browse the web or ping network resources. I would like to disable the "DefaultWebVPNGroup" without any consequences for the installation program. What I still have to disable?
-------------------------------------------------------------------------------
Output from the command: 'show running-config '.
: Saved
:
ASA Version 8.4 (2)
!
ciscoasa hostname
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
192.168.123.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
boot system Disk0: / asa842 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
Server name 208.67.220.220
name-server 208.67.222.222
permit same-security-traffic intra-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
object-group service DM_INLINE_SERVICE_1
the purpose of the ip service
the purpose of the tcp destination eq https service
the purpose of the tcp destination eq pptp service
the purpose of the service tcp destination eq www
object-group service DM_INLINE_SERVICE_2
the purpose of the ip service
the purpose of the tcp destination eq https service
the purpose of the tcp destination eq pptp service
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_1 all 192.168.123.0 255.255.255.0
inside_access_in list extended access allow the object-group 192.168.123.0 DM_INLINE_SERVICE_2 255.255.255.0 any
allow a standard ACL1 access list
ACL1 list standard access allowed 192.168.123.0 255.255.255.0
access-list nat0 extended 192.168.123.0 allowed any ip 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.132.50 - 192.168.132.60 255.255.255.0 IP local pool SSLVPNpool
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
NAT (exterior, Interior) source Dynamics one interface
NAT (inside, outside) source Dynamics one interface
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 76.x.x.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.168.123.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
interface ID client DHCP-client to the outside
dhcpd dns 208.67.220.220 208.67.222.222
dhcpd outside auto_config
!
dhcpd address 192.168.123.150 - 192.168.123.181 inside
dhcpd allow inside
!
a basic threat threat detection
host of statistical threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow inside
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.3054-k9.pkg 1
AnyConnect image disk0:/anyconnect-macosx-i386-2.5.3054-k9.pkg 2
AnyConnect enable
internal group SSLVPN strategy
SSLVPN group policy attributes
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
by default no
the address value SSLVPNpool pools
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect ask flawless anyconnect
attributes of Group Policy DfltGrpPolicy
value of server DNS 208.67.220.220 208.67.222.222
client ssl-VPN-tunnel-Protocol
username Vxxxxx ZyAw6vc2r45CIuoa encrypted password
username Vxxxxx attributes
VPN-group-policy SSLVPN
client ssl-VPN-tunnel-Protocol
admin password 61Ltj5qI0f4Xy3Xwe26sgA user name is nt encrypted privilege 15
username Sxxxxx qvauk1QVzYCihs3c encrypted password privilege 15
Sxxxxx attributes username
VPN-group-policy SSLVPN
client ssl-VPN-tunnel-Protocol
tunnel-group SSLVPN type remote access
tunnel-group SSLVPN General attributes
address (inside) SSLVPNpool pool
address pool SSLVPNpool
Group Policy - by default-SSLVPN
tunnel-group SSLVPN webvpn-attributes
allow group-alias SSLVPN_users
!
!
!
World-Policy policy-map
class class by default
Statistical accounting of user
!
service-policy-international policy global
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:989735d558c9b1f3a3a8d7cca928c046
: end
----------------------------------------------------------------------------------------------------
Thanks again to all.
To access the internal resources of VPN, here's what needs to be configured for NAT:
obj-SSL-pool of network objects
192.168.132.0 subnet 255.255.255.0
object obj-Interior-LAN network
192.168.123.0 subnet 255.255.255.0
Static NAT obj-Interior-LAN obj-Interior-LAN destination source (indoor, outdoor) obj-SSL-pool static obj-SSL-pool
I also advise you to remove the following statement of the NAT:
NAT (exterior, Interior) source Dynamics one interface
If you want all traffic internet VPN to be routed to the tunnel, then here's the NAT config:
object obj-SSL-internet network
192.168.132.0 subnet 255.255.255.0
dynamic NAT interface (outdoors, outdoor)
And finally, you cannot disable the group policy by default 'DefaultWebVPNGroup '. So that when you log-in, you chose
SSLVPN_users group of tunnel, which will apply SSLVPN automatically group policy that you have configured explicitly that.
I hope this helps.
-
Help! Configuration VPN Pix535 does not
Hello
We are trying to implement a remote vpn to allow clients to our private lan and then be able to use outgoing https. Don't break the tunnel, according to the needs of the client to look like they come from our area. Any help would be greatly appreciated. We can connect to the vpn with the customer, and we can ping within the network, but have problems trying to use HTTPS coming out through the client. Please find my current config attached. Thanks in advance.
permit same-security-traffic intra-interface
NAT (outside) 101 172.21.200.0 netmask 255.255.255.240
I would also add...
ISAKMP nat-traversal crypto
-
Cisco ASA 5505 - Configuration VPN
I'm trying to configure a VPN connection to allow customers access to the internal network. I have tried to use time Wizard VPN & repeatedly but customer connect but can get out to the internet and communicate with any host on the network. I tried to use a vpn in the 192.x.x.x or 10.10.1.X network dhcp pool but no luck.
Comments or suggestions appreciated.
What is the reason for these commands?
NAT (outside) 0-list of access policyPAT
NAT (outside) 5 10.10.1.0 255.255.255.0
If this isn't spicific reason remove
and put the following command:
Permitted connection ipsec sysopt
in global configuration mode to enable the VPN traffic to work around interface access lists
Good luck
If useful rates
-
Configuration VPN error easy need help
using CCP 2.1 I tried to assign the IP to the new loopback interface, when I did a show ip interface br he showed the unordered interface
Virtual-Network1 unassigned YES unset down down
Loopback1 unassigned YES TFTP upward upwards
Virtual-Template2 unassigned No. TFTP low low
Here is the code that the ccp created
interface Loopback1
no downtime
IP 10.69.241.0 255.255.255.0
output
So I tried to add the IP through the console
MyRouter (config) #interface loopback1
MyRouter(config-if) #no shutdown
MyRouter(config-if) #ip address 10.69.241.0 255.255.255.0
Bad 24 for address 10.69.241.0 mask
MyRouter(config-if) #.
What I am doing wrong?
Thank you
Tom
Connection using the Cisco VPN client (binary version 5.0.07.0440 on Windows 7 Ultimate 64 bit) gets one for your password invite after initially specifying your 72.88.223.20 IP public and the TGCSVPN group with password tgcsvpn01 group. Validates a user name and password would be required to successfully complete the authentication of login and validate your VPN configuration.
-
WRT1900AC cannot configure VPN
I CURRENTLY HAVE 2 WIRELESS ROUTERS AN ASUS RT-N56U WHICH WAS EASY to set UP WITH ExpressVPN. COMING TO EXPAND MY NETWORK & IMPROVE USING A LINKSIS WRT1900AC. UNABLE TO SET TO THE TOP OF THE SAME. BOTH ROUTERS ARE HARD CABLES TO THE ISP ROUTER & WILL BE POSITIONED AT DIFFERENT AREAS OF THE HOUSE FOR COVER. I HAVE THE ExpressVPN PAST & DETAILS USER password, LIST OF GLOBAL SERVER ADDRESSES & THEIR ADDRESSES IP CONCERNED.
CAN SOMEONE HELP ME IN THE BASIC CONFIGURATION. I AM NOT AN IT WIZZ BUT YOU CAN FOLLOW THE INSTRUCTIONS ESPECIALLY WITH SCREENSHOTS SUPPORTED. HELP IS GREATLY APPRECIATED.
OK gents,
Answers very well. It gives me a lot to think so thank you very much.
Temporarily, I currently have 2 routers connected switch wired to asus to linksys with the linksys being connected on the local network of the asus through the cable network. The asus is configured as L2TP that allows the details of user, password & VPN server. Use them in this way gives me the IP addresses associated with the address of the server used. This IP address is provided if connected to a router. Probably not the fastest or the best way but will suffice until I have work on your tech talk. I have an ASUS RT - 68U (which has the VPN Client) available to replace the Asus RT - 56U to come. I can use the 56U on the edge of the property similar to the linksys. Trial & error prototyping will I hope make me it in the absence of knowledge or understanding.
Can someone advise on potential pitfalls with the current configuration or plans for the future?
Thanks again.
-
Cisco 1921 - how to configure VPN multiple Tunnels to AWS
I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps.
C1921 #sh run
Building configuration...Current configuration: 2720 bytes
!
! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
!
version 15.5
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname C1921
!
boot-start-marker
boot-end-marker
!
!
logging buffered 52000
enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
!
No aaa new-model
Ethernet lmi this
!
!
!
!
!
!
!
!
!
!
!
!
Research of IP source-interface GigabitEthernet0/1 domain
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
license udi pid CISCO1921/K9 sn FTX1845F03F
!
!
username admin privilege 15 password 7 121A0C041104
paul privilege 0 7 password username 14141B180F0B
!
redundancy
!
!
!
!
!
!
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
lifetime 28800
ISAKMP crypto keys secret1 address 52.35.42.787
ISAKMP crypto keys secret2 address 52.36.15.787
!
!
Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
tunnel mode
!
!
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel 1 to 52.35.42.787
defined by peer 52.35.42.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
map SDM_CMAP_1 2 ipsec-isakmp crypto
Description 2 to 52.36.15.787 Tunnel
defined by peer 52.36.15.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
Description connection Wan WAN - ETH$
IP address 192.168.1.252 255.255.255.0
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
interface GigabitEthernet0/1
Description of the connection to the local network
IP 192.168.0.252 255.255.255.0
automatic duplex
automatic speed
!
IP forward-Protocol ND
!
IP http server
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent!
recording of debug trap
host 192.168.0.3 record
host 192.168.0.47 record
!
!
Note access-list 100 permit to AWS Tunnel 1
Access-list 100 CCP_ACL category = 20 note
access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
Note access-list 101 permit to AWS Tunnel 2
Note access-list 101 category CCP_ACL = 4
access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
!
control plan
!
!
alias con exec conf t
SIB exec show int short ip alias
alias exec srb see the race | b
sri alias exec show run int
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
line 2
no activation-character
No exec
preferred no transport
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
local connection
transport of entry all
transportation out all
!
Scheduler allocate 20000 1000
!
endThere should be no second tunnel.
I use either a peer or the other, but not both at the same time.
To display both at the same time, you need to use the Tunnel interfaces. Amazon would have you sent pretty much the exact commands to copy and paste into.
-
Need help with VPN (Cisco831 + ASA5510)
Hello
We are trying to set up a VPN site-to site between a Cisco831 and an ASA5510.
I have attached two units configuration files and file of the SAA.
on the 831, we get:
KED1CSPSVPNr01 #.
* 19 Mar 22:17:48.743: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode failed with the peer to 8.10.15.130
I can't figure out where the problem. Could someone help please?
Thank you.
try to add to the ASA...
card crypto outside_map 1 set pfs
-
I have a wrvs4400n intending to allow VPN access to my computer at home instead of simple RDP using port forwarding. However, I can not understand how to configure the VPN wrvs4400n. I don't think that I need a tunnel as the connection from my laptop will be different locations depending on where I'm travelling to. My home network has a dynamic IP address, but I set it up with dyndns.org, so I know the IP address all the time. I hope that this will be a simple task, but it turns out that I'm dead in the water... All advice and support would be greatly appreciated.
The joint should help you get started using the QuickVPN Client, which can connect to your WRVS4400N at home from the internet.
Maybe you are looking for
-
iPhone ring 3 times then direct to voicemail
My wife 6 IPhone stopped accepting all incoming calls. Upon receipt of the call, it rings three times (aloud) and goes directly to voicemail. I tried all the usual redefinitions and re - started. Any thoughts on what I'm missing? Thank you Toby
-
Re: Unable to run P0056v200.exe (BIOS update) on Tecra S5 with Vista Ultimate
When I run the utility of the P0056v200.exe of Windows bios update I get the message "Toshiba BIOS package Ver.3.2.8: this computer is not supported."I have found no 'traditional' for the Tecra S5 update procedure.Anyone have any idea how can I updat
-
Activation of the Games Big Fish Games-
I tried to activate a game from Big Fish Games, but I get this: "Microsoft Windows has stopped working, a problem caused blocking the program works correctly." Windows will close the program and notify you if a solution is available. » I tried to ac
-
How can I get rid of the error oxc0000135 status? It does not my pc start.
Under XP Home edition, I get the error message status oxc0000135. Even when I try to reboot from the windows CD.
-
I use my HP G72 laptop around the House and always plug into a wall outlet (be careful to first connect to the laptop and only then in the socket). I don't keep it turned on all the time, but use it only about one or two hours a day. Since he does no