help! on the backup of data

Similar Questions

• accelerate the backup of data received through series

  Hello

  I hope you can give me some advice. So far, I have not found a solution.

  I have a sensor connected by USB-serial converter to the computer (COM 2). After the beginning of the measure, the sensor sends continuously data as a string. The sensor is able to operate at different speeds and it is controlled through strings sent to the device.

  Now, I have programmed a small piece of code to read and evaluate the data from the sensor. There is no problem while looking at live data in several locations. But as soon as I try to save the data, I have speed issues. The loop is not fast enough to receive the data, because it is provided by the sensor. Temporarily remove the plots and so on, don't help not, therefore the problem is data backup. As far as I know, I should use the tables that I did and I don't think that editing bays should be the bottleneck, because they should be able to manage data in general much faster.

  In the Hyperterminal with windows, the unit works fine.

  I use VISA series with a timeout of 2 s and a buffer of 128. Baud rate is set to 460800.
  The real VISA read command is set to read 50 bytes max or stop a tank of termination (line break).
  After initialization, and sending the command start for the sensor, the device starts to send its data...
  The different speeds are:
  1 - 4 strings per second
  2 - 10 per second
  3 - 100 per second
  4 - 500 per second

  Each line gets cut, evaluated and plotted. Each value is also stored in a table (which could be saved after the program stops).

  In the photo, I deleted several commands sent to the probe, because they are not relevant and it doesn't matter (of failure) if I remove them in the program or not. It goes the same for plots. After setting the device at the higher speed, the program fails, because there is more data than labview bed. (I have already said, that without the tables it works very well, I do not have it?).

  So, what can I do? I'm doing something completely stupid? Is there a faster way to collect data with labview? I mean, 500 HZ, which must be nothing.

  Thanks for your help.

  Kind regards

  HD

  PS I'm continues LabVIEW 8.6

  Computer: Intel Core2 Duo E8500 3.16 GHz with 3 GB of RAM

  SW: Windows XP SP3

  You use insert into table with each iteration and forcing LabVIEW to keep reallocation memory for the berries. It is not very effective. Instead, I advise you to use the architecture of producer/consumer and transmit data back to the consumer loop where you write the data. Shift registers and who would skip all the functions to insert it in the table. You also use local variables and property nodes. Neither one of those who are very fast either. Can't tell from the picture why those are used. Also, consider using a structure of the event for these Booleans wired for the structures of the case. Do you really need those who questioned all the time and run the code with each iteration, or do you just need them to run once when the Boolean value changes?

• Help restore the backup catalog

  Hello

  PSE made a mess on the dates of my video clips in the Organizer (who is the subject of another thread). Before you perform a full restore of my backup months old, I want to restore ONLY the catalog it (not the image files) and do coexist with my current messed up catalog. This way I can see if the problem is in the database or in files of video clips.

  I would like to know what files I have to leave my set to my catalog restored backup to work. To prepare for this post, I looked at help | Info by the system to search for the location of the folder that contains the current catalog. Inside this folder there are some subfolers and some files as follows:

  Subfolders:

  breezeData

  CAXMPFiles

  Style

  SyncDB

  Files:

  backupCt.dat

  Catalog.pse8db

  collstatus.dat

  Thumb.5.cache

  Watch.2.cache

  ((1) which files I have to restore and 2) where should I place them so that the restored catalog works properly?

  Because the restored catalog will have the same name as my current, how can I open it in the Organizer without deleting the current?

  It seems that the catalog file is not the name of the catalog itself, as it was a few versions ago. For example, my catalogue is called "My catalog", but the database file is named "catalog.pse8db".

  Remember I want to ONLY restore the catalog database; not the actual image files.

  Thank you for your help

  The entire folder containing the "catalog.pse8db" represents the appropriate catalog.  The name of the folder gives the name of the catalog. You can restore this folder anywhere you want, but it can be convenient to restore in the same parent folder containing your current catalog file (help > System Info to find this place).

  A shortcut that is convenient to open any catalog is double-click on "catalog.pse8db" of Windows Explorer.

  If you are synchronizing with Photoshop.com, remember to turn off sync from the opening of the restored catalog.  Otherwise confusion might ensue.

• Help on the passage of data between vi when built in exe

  Hello

  I have this problem and grateful if someone can give me a heads up the right direction.

  I'm trying to write a program for acquisition of data and control of two instruments simultaneously.

  An instruments is a rotating stage that I control the movement and data read using activex controls. I do this in a vi that I have two distinct time of lines, one for updating the Rotary floor continuous data and other while loop for the handles of event structure.

  The second instrument is a detector that follows the rotation of scene. For this, I have an another vi with two loops for example, for data acquisition hollow rs232 and another while the loop is to the structure of the event.

  I use globals to pass data between the vi and it works very well in a labview project environment. However when I Isaiah to compile these exe files. I can no longer spend data.

  Is there a programming method when you communicate with more than one instrument. What I want to ask is, say I have a function, oscilloscope etc engine generator How can I control them in windows separated (for example, separate programs) and pass data to the other?

  I would be grateful for any help.

  Hello

  Global variables are not accessible to separate executables because their areas of memory are not shared. This can be found in the following document: If I can use a Global Variable to share data between two executable LabVIEW? The only way to have it working would be to use a main VI that launches your two separate applications like subVIs. This would allow you to share a global variable between the two. Your other option would be to use the method described in the article, or to use shared Variables: How to communicate between several executable LabVIEW using shared Variables?

  -Zach

• need help with the backup of the copy of the OS

  Hi team,

  I bought the new Presario CQ40 and I need help regarding the opertaing and activation office 2007 system backup, please respond as soon as POSSIBLE.

  Thank you and best regards,

  Nancy (Julien).

  Are you needing information to create the recovery disk set? HERE

  As for activation Office 2007-if you paid for a license extend the 60-day trial version, simply enter your key when asked to activate. If you have not purchased a full license, you should be the link for the purchase of Ms. You can also buy Office 2007 locally(probably cheaper) and just use him license key to activate your preinstalled version.

• Windows Backup & restore leaves gaps in the backup period date ranges

  I noticed that backup & restore leaves gaps in the date ranges displayed on the screen of backup periods under the function to manage the space.  This means that files change during the interval periods have not been saved?  For example, the screen shows currently backups and the following periods:

  Jan 26: 12-18 Mar, 12 GB 10.40

  Apr 04, 12-13 Apr, 12 GB 19.62

  27 April, 12-27 Apr, 12 GB 05.16

  May 06,12 - May 06,12 02.41 GB

  May 27.12 - 17 Jun, 12 GB 03.41

  What is the importance of gaps?

  How can I tell that B & R is fully backup all files that changed since the last backup run?

  How can I varify the 1st backup is a backup full?

  How can I varify that the system image backup is up-to-date?

  I save approximately once a week to a USB external hard drive. I use options "Include a system image" and "Let me choose" to select the files and have selected the option 'keep only the last frame system & minimize the space used '.

  Hello

  Backups are created in sets called backup periods. To maximize your disk space, Windows backup backup all folders selected, the first time it's run and then it only backs up files that are new or have been modified since the last backup was made. Periodically, Windows creates a new, full backup. Each full backup is called in a backup. When you view your backups of files, you can see all the backup periods with date ranges. If you decide to delete backups of files, you should always keep the most recent backup of the file.

  Reference:

  Should what backup settings I use to maximize my disk space? http://Windows.Microsoft.com/en-us/Windows7/what-backup-settings-should-I-use-to-maximize-my-disk-space

  Back up and restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/products/features/backup-and-restore

• Help in the merging of data and create mailing labels

  I have a CSV file with three field ("name, envelope" "" = address"and"City ST Zip") and 245 records.

  I have the labels that correspond to seven on a page.

  I have the designed document. I am able to get the fields inserted, but... when I merge, I get the first page with seven the first record labels, the second page with seven second record labels, page 3 with seven third record labels. You get the photos. I want seven different addresses on each page. So... instead of having more to 35 245 pages.

  Is this possible or should I find a way to make my drawing in Word? * sigh *.

  Everyone made the same mistake; you set seven (records) to your InDesign document, are not.

  Create the first instance (upper-left)

  Go to control panel to merge the data and choose multiple records per page.

  It helps to have put guidelines in place for the Visual presentation and I try to keep the total area of my equal fields the number of hole - exactly 2 inches of width, for example.

  Data merge multiple records per page will need the values for spacing from room to room. Integers and guides make easier.

• Help with the problem of data type...

  Hi friends,
  
  I have a requirement. I have a warrant 2 guests (from and to). The data contained in the guests are like "Fall 2006", "spring 2006", "full of 2006", "Academic 2006"for a given year. " I have data from the year 2000 to 2008. The data type of the column duration in varchar. I have a report corresponding to this prompt. This report works well if it is not linked with the guests. If I have this tie with guests, its giving me results because in the report I gave filter as term is greater than or equal to ' fisrt_pv "(où first_pv est la variable de présentation j'ai utilisé pour mon d'invite de terme... comme second_pv sage est pour à terme rapide) and the term is less than or equal to"second_pv"."» So, if I put my guest (and) fall 2007 and (spring 2008 to) and run the report, its sends a fall 2007, Full 2000... Full2008, spring 2000... Spring 2008. It is because it is comparing the term based on letter of departure with all the other term. We know that the fall 2007 and spring 2008 are next to next semesters, is expected to see just a 2-column output. How do oracle know that?
  
  I have a term_number associated with this table numbered 1 to the spring of 2000, 2 Full, 3 for autumn 2000 2000, 4 for academic 2000... all the way up to academic 2008. I used this area to the command prompt to order because I want the guest to show as the spring of 2000, Full 2000, fall 2000 etc. instead of 2000 academic, University 2001... hope this field will be useful for you to analyze... I need your help to do this... If you need other info let me know... Thanks for your time n help...
  
  Kind regards...

  Yes. The problem is that your guests are CHAR, so the calculation "superior to" is done alphabetically rather than numerically. This digital keys.

  Create two columns to contain the term_number that match the values selected in your guests. Then the BETWEEN operator do not filter on numeric values. You can still view the CHAR values in your report, but now they will be in the range that you would expect.

• RMAN change the backup of data files directory

  Hi all!

  I have question for RMAN. My backups keep in fast_recovery_area (/ opt/oracle/fast_recovery_area). I want to change the path of my fast_recovery_area to another location. I've changed that through SQL more command: ALTER SYSTEM SET DB_RECOVERY_FILE_DEST = ' / opt/oracle/backup ' SCOPE = BOTH SID ='* ';

  Now, my fast_recovery_area is in this path/opt/oracle/backup. In the fast_recovery_area, I have 4 folders (archivelog, autobackup, backupset datafile). All folder is created in the new location and RMAN write successfully the file on the new location except a single file (datafile). How can I change this option for this folder that writes to the new location. P.S datafile directroy have * dbf files backed up nightly.

  Thank you!

  You use an incremental update strategy of backup.  The level 1 backup is always aware of the 'previous' 0 level backup in the old location, so it is not a fee L0 backup in the new location.  You can remove the old backup, run a BACKUP DUPLICATION and OVERLAPPING COPY OF DATABASE for Oracle to be aware that the L0 backup no longer exists.  Then, run a fresh backup for Oracle create a new backup of L0.

  Hemant K Collette

• Help on the manipulation of data

  I hope I can explain it properly, go here
  
  I do a program help desk for a conversion on an old program help desk, in each case, there is evidence, but instead of putting this info a clob, the former program
  a pointer to the column as C:\Documents and Settings\burnetde\Desktop\Daarel has ' done s\Remedy\Ms closing Requests.msg DR
  and as
  C:\Documents and Settings\dburnette\My Documents\SCRs & DRs\Z Cooper Notice_Jun 05.Marco doc update
  
  so not all the same.
  
  then the old program comes all the docs support real in a directory so that just the names are in there as
  MS made DR closing Requests.msg
  Doc 05.Marco Z Cooper update Notice_Jun
  
  hope that can I do correspond to the top and put them in a clob in my new program.
  
  Thanks for you help,
  Doug

  more a question of sql or pl/sql to an apex question actually :)
  Select substr ( , instr ( , '-',-1) + 1) twice;

  something like this should do the trick.

• Windows running in the backup drive D: after system reboot

  I rebooted my system yesterday and discovered that it had been done in the backup drive D which has only 1 g backup space. I can't do another reboot because there is no space in the drive.

  My question is: A) how to get the operating system to run on the main C drive

  (B) I'll be able to remove the old operating system to drive D

  Dell XPS 1530

  Vista 32 bit

  Any help is greatly appreciated, thank you

  Delete older backups and free up space on the D drive.

  To remove old backup files, under the backup of data files, click View backups.

  You can then select the backups of files that you want to delete, which will free up disk space. Remove an entry in the list will not affect the other backups. If you think that you don't need one version of your files from a certain backup period, you can delete that backup. We recommend that you always keep the most recent backup.

  For more information, take a look here: http://windows.microsoft.com/en-US/windows-vista/Back-up-and-restore-frequently-asked-questions

  The man likes to play chess; Let's get him some rocks

• Time machine sees the backup, but not connecting to new machine

  Just did a transfer from MAC to MAC using Thunderbolt cable - everything is good!  Then, I wanted to make sure that the new Mac can access Time Machine backup file on the network file server.

  Old MAC - running El Capitan 10.11.3 - TM full backup to the network Central of Seagate drive is successful.

  New Mounting successful MAC - running El Capitan 10.11.4 - Time machine disk Seagate file

  . Name of the new Mac is slightly different because of the collision of network host names

  Various attempts to select the reader appear to succeed but the backup information (Date of last backup) are not displayed.

  Entering Time Machine will display the finders stacked, but it will timeout to 30 seconds, saying: he cannot connect to the backup file.

  UNIX command 'mount' shows the machinery once mounted via afp: in /Volumes

  (From old Mac - should be present)

  Rich@SeagateHomeDisk._afpovertcp._tcp.local./SeagateHomeDisk%20TM%20Backup on the Volumes/SeagateHomeDisk TM Backup (afpfs, nobrowse)

  (But on the new Mac - mounts like this)

  [email protected]/SeagateHomeDisk%20TM%20Backup on the Volumes/SeagateHomeDisk TM Backup (afpfs, nodev, nosuid, ridden by rickenne)

  To verify access to the backup file, I started the old Mac and accessed fine.

  Note that I try to not to have the two machine upwards at the same time.

  Should I clean server Seagate Keychain Access permissions for the file mounted correctly?

  How is the drive connected to the network?

• Need help with the MapPoint 60-day trial versiio

  I installed the free trial 60 days of MapPoint and need the following help.

  I was able to create a map from an Excel spreadsheet and now map shows the 61 locations as landmarks. How can I change the Pushpins to look more like a data label. I want that every location mapped to display the name of place. The name of the place is a column in my spreadsheet. I already went through the help on the labels of data and pushpints, but I don't know what to do.

  It would be great if someone could call me.

  Thank you

  Vickie Johnson |

  Program Manager, q.. |

  MapPoint forum seems to be:

  http://social.Microsoft.com/forums/en-us/streetsandtrips/threads

  Please ask your question there. The site of answers doesn't have a forum for MapPoint.

• Easy way to monitor the Backup Exec 12.5 +.

  Someone at - he found a way to do this? We had to work at 11, but when we went, it seems that syamntec has changed the way it reports in its database.

  Can you give us more information about the way you are / have been followed by Backup Exec 11? As what extension of BB are / were you helps monitor the Backup Exec 11? In addition, details of the power failure; execution of the extension will fail at all, at some point, no matter what STDERR? And what version of BB you running now?

• How to decrypt the backup file

  Hi all

  I need to know how to decipher the backup file (ACS 5.3) on the desktop. Below is relevant for once you import the file to restore. However, my problem is to extract the file to your desktop

  ============================================================

  GBA backup encryption

  Backup of the ACS is now encrypted using a password of dynamic encryption. The user is prompted for an encryption password when executing a backup operation. ACS encrypts only the ACS data by using a dynamic encryption key. CARS and the ACS view data is encrypted using a static key. That is why ACS invites to enter a password for encryption when you perform a backup that contains the data of the ACS. The user is prompted for a password for decryption while restoring a backup that contains the data of the ACS.

  When you run a backup in ACS, ACS uses the static to encrypt key the CARS and the ACS data and actually a file of .gpg while GBA backup data is saved inside this file as file separate .gpg .gpg using the dynamic encryption password. When you restore the full backup, ACS invites for the decryption password decrypt the backup ACS data. ACS decrypts the data from CARS and display ACS data using the static key.

  The encryption password must have:

  • a minimum of 8 characters
  • no more than 32 characters
  • letter at least one capital letter.
  • at least a tiny.

  «Special characters are allowed except "'", "$", "(" et "") "» ACS displays the password strategy if the entered password does not meet password requirements.

  ===========================================================

  for people who would ask "Why I want to do this": it's policies related audit password standards

  Hello

  I can't think about a way to recover your files, it's to restore the file to a temp ACS server can generate a backup that is not encrypted.

  I would say we can decrypt the file on your desktop if we know the method that was used to encrypt it. I think that this information is not provided anywhere in the doc of cisco.

  Kind regards

  Amjad