Help out me... On my PowerEdge R710

Similar Questions

• Connect a Powervault MD1200 to a PowerEdge R710 5.1 running esx using SAS cables

  Hello

  I bought a Powervault md1200 and a perc h800 controller.

  I'll install the perc controller in my PowerEdge r710 5.1 running esx server.

  Then connect the md1200 to the r710 via sas cables. The powervault is no NIC.

  My question is, how to configure the RAID while booting the r710? I understand that if I were on Windows, I could use open manage but I'm not familiar with how to do this from a 5.1 esx server.

  I'd appreciate any help.

  Thank you

  Flynn

  Hello Flynn,

  What you need to do is to go into the Bios of your H800 controller and you can then configure your virtual disk MD1200.  Once you have the virtual disk created, then you will be able to do a scan in ESX & he should see the virtual disk that are created.  To access the boot controller bios you need to hit Ctrl + C to enter the bios.

  Please let us know if you have any other questions.

• Adding disks RAID PowerEdge R710

  We have a PowerEdge R710 running a RAID1/RAID5 configuration.

  • PERC 6 / i SAS Raid Controller with 2 x 4 internal connectors.
  • RAID1 is composed of (2) 146GB 15K drives 2.5 "SAS.
  • RAID5 is composed of (3) 500GB 7.2 K Nearline 2.5 "SAS drives.
  • (3) empty bays are available.

  The server running VMware ESXi v5.0.0. We have almost maxed out storage so I need to add storage. I don't know what are the options I have to do this. These are the options that are possible, I hope.

  • Add 500 GB (3) discs the same as installed readers and expand the RAID5.
  • Add 500 GB (3) discs the same as installed readers and create a 2nd RAID5.
  • Add (3) 1 or 2 to 7.2 K near-Line SAS 2.5 "drives and create a 2nd RAID5.

  Can the PERC6 / i controller supports an another RAID5?

  bhartung

  • Add 500 GB (3) discs the same as installed readers and expand the RAID5.
  • Add 500 GB (3) discs the same as installed readers and create a 2nd RAID5.
  • Add (3) 1 or 2 to 7.2 K near-Line SAS 2.5 "drives and create a 2nd RAID5.

  These are possible.

• Documentation on the establishment of a PowerEdge R710 from scratch

  I got a PowerEdge R710 with no hard drives (and out of warranty). I added 6 WD RE3 1 TB disks. I'm new on PERC controllers and don't know how to start the implementation of this table. The only documentation I found was Dell PowerEdge RAID Controller cards H700 and H800 Technical Guide but it says nothing about the configuration of the table I can find. Is there documentation for a complete reconstruction of this server?

  I'm probably not the first person to do

  

  There are more than 1 way to get discs into the caddy. One of them will result in the data connection and feeding only reaching no not the player no matter how hard push you into the slot. I still have problems later, but I see you pushing me now.

• Hard drive by PowerEdge R710 [MS]

  Good afternoon,

  It ns. Server DELL PowerEdge R710 (service tag ) ha UN disco che da problemi.

  The machine went up quattro "500 GB near line SAS 6 GB/s, 7.2 k 3.5"disco board hot-plug".»

  Ho tried a ' dare in the giro, my seems to che gli occhiata hard disk the da near Line SAS esistano più non 3.5 ".

  Could by help favore disco UN find by auswechseln quello che sta guastando if?

  Grazie thousand. Silvia (T.E.S.I. S.r.l.)

  Buongiorno,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi come message privato di seguito required information?

  By the spedizione (intervento o):
  1. company name:
  2 address:
  3 City:
  4 Provincia:
  5 cap:
  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione
  1 nome società (is it client code):
  Address 2:
  3 City:
  4 Provincia:
  Heading 5:
  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:
  7 partita IVA

  Speaking saluti

  Manual

• Problem updating iDRAC and LC on Poweredge R710

  Hello

  I am facing problems updating one of our Poweredge R710 (all others worked like a charm). Using OME I could install almost all day, but iDRAC (Firmware 1.10--> 1.95) updates and controller of lifecycle (application 0--> 1.6.0.73) will not be successfully completed.

  OME to ESM_Firmware_CMDN0_WN32_1.95_A00 error message. EXE: "performance operation exceeded a specified time-out period. The update has not completed; You must restart your system and try again. "(even after several server restarts the message is always the same).

  Error message in OME for lifecycle - Controller_Application_GFFFC_WN32_1.6.0.73_A00. EXE: "update failed: failed to secure copy - the secure copy function has failed.

  When starting the server "Update Services system requirements" is shown in the upper right of the bootscreen. I've tried ressetting iDRAC (Ctrl + E at the start), turn off the server for 30 minutes (cable unplugged, replugged, waited 5 minutes, powered by the server) update system Build & Update Utility thorugh with SUU 7.3.1 and finally using the CentOS OM 7.3 Live DVD. None of this has worked successfully and I have no more ideas. Maybe someone has a?

  Here are the necessary links. Fires within the OS.

  DRAC - http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=63KCR&osCode=WS8R2&fileId=3287900761&languageCode=en&categoryId=ES#

  Then run this, it is a set of lifecycle controller repair. http://www.Dell.com/support/drivers/us/en/19/DriverDetails/product/PowerEdge-R710?driverId=8F07J&osCode=WS8R2&FILEID=2731110409&LanguageCode=en&CategoryID=SV

  Then update the LC with this - http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-r710?driverId=F0D50&osCode=WS8R2&fileId=2984894513&languageCode=en&categoryId=SV#

• PowerEdge R710 and perc h700, disc not visible in OS

  Hey,.

  We have PowerEdge R710 with perc h700 raid 5 controller physical drives under raid6 running. We have recently added a sixth of the road which is much smaller (512 against 4 TBS) we want to just format and use it as a normal drive in the OS (Ubuntu 12.04.5).

  However, the drive is not visible in the operating system. When you enter the settings of the RAID controller that it says that the drive is READY but not configured and all the options to the title of operations are grayed out. How can we make this hard drive is visible in the operating system?

  See you soon

  The H700 does NOT support non RAID, so all records first must be configured on the controller, before its presentation to the BONE. You must configure (initialize) as a single drive RAID 0.

• New SATA HDD are not detected on PowerEdge R710

  Hi guys,.

  I have a PowerEdge R710 with the reference number below

  Service number: ADMIN NOTE: maintain the label removed by privacy policy > | Express service code:

  ADMIN NOTE: kidnapped by the Express service code privacy policy >

  I have 2 x 750 GB SATA HDD that are not detected at boot of the server. Obviously, the installation of Windows Server 2012 is not possible because it does not find any drive installed in the system

  Please help as I am new to the hardware configuration.

  Thank you in advance.

  You must configure RAID first. If you use the RAID S100 controller on board, it is not compatible with 2012.

• Adding additional disk to ESXi 4.1 Datastore on Dell PowerEdge R710

  Greetings,

  We currently have a Dell PowerEdge R710 with 6 SAS das drives configured in a RAID-1/RAID-5 configuration. A drive is configured as a global hot spare. I would add this spare drive in the RAID-5 table, where some virtual machines live, to recover additional space. Has someone managed to do this? Is the only way via the PERC BIOS management utility?

  Thank you!

  I'm not part "raid-1/raid-5.  But assuming that the table is raid-5, then yes it is possible and yes the BIOS utility is necessary.  The hot spare is currently set should be removed from this role, then added to the existing Bay raid-5, but without the ability to select increase.  This will create free space on the raid-5 array on which then a new logical volume can be created, which will be then seen by ESX as a new drive and therefore another data store can be added to this (or it can be added to the first as a measure).  HTH

  http://blog.peacon.co.UK

  Please give points for any helpful answer.

  Unofficial list of transfer USB devices work

• PowerEdge R710 24GO of RAM 40 GB upgrade

  Hello

  Our PowerEdge R710 has 2 processor E5620 and 24 GB of RAM (6 x 4GB Dual Rank registered synchronous DDR3 1333 MHz). The memory is set to optimizer mode and uses the memory following media:

  • A1
  • A2
  • A3
  • B1
  • B2
  • B3

  In the next 12 hours we want to add 4 x 4 GB of additional RAM (modules) so that we have 40 GB of RAM instead of 24 GB. The owner's manual gives only configurations for 32 or 48 GB RAM. What should be used? The following configuration is correct?

  • A1
  • A2
  • A3
  • A4
  • A5
  • B1
  • B2
  • B3
  • B4
  • B5

  M., accommodation,

  With the configuration of the CPU, as well as the existing configuration, you would not be able to add 4 DIMMS to 4 GB. Either you need to add 6 2 DIMM 4 GB or 4 GB DIMMS. It will be because of the rule of memory you must also complete 3 memory channels. With this said beening DIMMs would be met as one of the following values;

  Addition of 6 4 GB DIMMS (two results in 48 GB)

  A1, A4, A7, A2, A5 and A8 / B1, B4, B7, B2, B5 and B8

  or

  A1, A4, A2, A5, A3 and A6 / B1, B4, B2, B5, B3 and B6

  Addition of 2 4 GB DIMM

  A1, A2 and A4, A5 / B5, B2, B1 and B4

  Let me know if this helps to clarify.

• Dell PowerEdge R710 memory upgrade 16 GB (4x4Go) for 72GO with more than 64 GB (8x8Go)

  Hi all

  My Dell PowerEdge R710 is seen 16 GB (4x4Go) now and would like to add 64 GB (8x8Go), it will be total 72GB. Please help me add memory into the slot on the right. Can I do the following as below

  A1/B1 > 8 GB

  A2/B2 > 8 GB

  A3/B3 > 8 GB

  A4/B4 > 8 GB

  A5/B5 > 4 GB

  A6/B6 > 4 GB

  Thanks Robert, I already bought 64 GB (8x8Go) and would like to add to my current server which is running 16 GB (4x4Go). So, please show me how.

  Thank you

  Binh Kien

• DELL PowerEdge R710 and PERC H700 RAID driver for WIn 2008 Std

  Hi all

  I have a DELL PowerEdge R710 with a controller RAID PERC H700.

  I try to install Windows 2008 Std 64 bit, but I can't find the driver. Even for the site web at support.dell.com. Can someone help me.

  THX in advance

  Even if you use a driver of 2008, it should at least recognize it, then you must be using the wrong driver or something wrong :)

  If you are installing 2008 R2, make sure that you use this file:

  If you install 2008 x 64, make sure that you use this file:

  With one, you must first unlock the .exe (right click on the .exe, properties, unlock), unzip / extract the files (run it and make a note of the default location), and then copy the 4 files on a CD, USB, etc., then when Windows tells you that he is not all hard disks, click on the link drivers load below to load the drivers from the media you have chosen.

• I would like to contact the former owner of the iphone I have, but have no way can help out me?

  I would like to contact the former owner of the iphone I have, but have no way can help out me?

  < personal information under the direction of the host >

  We can not. We are just other users like you.

  Apple is. For reasons of confidentiality and security, they are not allowed to share this information.

• Dell PowerEdge R710 - power Ricambio

  Buongiorno,
  Ho need di one ' offer by United Nations alimentatore per PowerEdge R710 con serial number FCL5WN1, dal supporto telephone Dell mi hanno detto di inoltrare the request that.
  Grazie. Saluti.
  Honeywell
  G.Casale

  buongionro, sto contattando via e-mail.

• Request alimentatore per PowerEdge R710 [CF]

  Buongiorno,

  avrei need di UN alimentatore per PowerEdge R710 take it cui service TAG e F4FRN4J, my dal supporto Dell mi hanno detto di write that. He codice che ho letto sull'alimentatore e n870p-s0, my come posso fare per sapere e thing i prices?

  In hoist foto dell'alimentatore.

  Buongiorno, the sto contattando by mail.

• [EC] PowerEdge R710 error: 5 E1810 HDD failure

  Buongiorno, di abbiamo UN UN PowerEdge R710 con TAG H1S5S4J che presenta error disco in oggetto. Chiedo UN preventivo como Logserv S.r.l. by the sostituzione nao.

  In attesa di a vostro riscontro, lascio Reed he mio personale interno. 0371-763973.

  Dear client,

  Con passing it mouse sopra identifier c Supporto Dell'e the voce "private message", it could mandarmi UN message privato.

  Nel caso in cui as aver need di assistenza telefonica is Pagaré a ticket di Assistenza.

  SE if need di una delle quotazione left in sostituzione can rates UN preventivo senza Pagaré the assistenza.

  By request, we have our o di need any it client codice di vecchia quotazione o.

  Nel caso in cui non his di queste information times need che compilasse i seguenti campi:

  -SERVICE TAG-

  By the spedizione:

  1. company name:

  2 address:

  3 City:

  4 Provincia:

  5 cap:

  6 name/last name/number phone/e-mail del referent in loco:

  With the fatturazione (is different)

  1 nome società (is it client code):

  2 via:

  3 City:

  4 Provincia:

  Heading 5:

  Name/last name/number 6 telephone/e-mail del referent by the fatturazione:

  7 partita IVA

  Speaking saluti

  EC