Help please, conversion devices for ESXi .ovf hard

Similar Questions

• Help Setup RAID SATA for ESXi 4.1

  Hello

  It is the first time that you try to use vmware.  Any help is greatly appreciate!

  I just built a server around the Intel s5500hcvr mother. I have 6 SATA HDD I want to set up in a RAID. The integrated RAID controller seems to be very limited and does not seem to be supported by ESXi 4.1 (when I run ESXi 4.1 installation and it asks for a location for installation, all my discs are individually listed instead of virtual drives that I created with the RAID controller)

  My questions:

  (1) what is the suggested configuration of HDD (RAID levels / number of berries) for ESXi 4.1?  Can I create 1 RAID 10 array and set everything up to that?  or take one of my disks and install esxi 4.1 on it and then create a RAID with the rest of my discs and use it to store data?

  (2) anyone can provide links to some SATA RAID controllers that are known to work with ESXi 4.1 (and is the supposed to recognize virtual readers created by the RAID controller setup ESXi 4.1)

  Your motherboard has a RAID controller software which, as you have discovered, is completely not taken in charge by ESX/ESXi... You will need to get a RAID controller that is on the HCL for SAS and SATA hard drives (not one with battery backup write cache) so you can use any type of RAID configuration.

  My preference for Internal RAID configurations (on the host) are two drives mirrored for ESX/ESXi to reside (preferably being SAS 10 k or 15 k RPM, 73 GB or 146 GB in size) and then another table for the data store. You'll want to keep the data slot store table 2 TB-512 b size in order to present to ESX/ESXi as a LUN. Or you will need to get a RAID card this split of the support to the top of the table in the smaller of the virtual drives that can be presented for ESX/ESXi and LUNS.

  Search for controllers using the LSI MegaRAID chip as a good first lap. Some Adaptec cards should work, but I've seen people post questions on those recent (more recent than in the past). MANY manufacturers rebrand/efficiency the LSI MegaRAID Controllers server, such as the Dell PERC 6 series cards.

  For the use of 4 disks SATA, RAID 10 (on a BBWC, fully supported, controller) will give you the best performance. It will compare with SAS drives however. IF you do not plan on any virtual machine running with anything beyond light IOPS / s then you should be ok (or with very light loads)... If this is going to be a production server, then get the SAS drives all around.

  VMware VCP4

  Review the allocation of points for "useful" or "right" answers.

• Help, please!  Configuration of ESXi to get Cisco Surv. Multimedia for work software.

  Quick overview of what I do:

  I am running VMWare ESXi on a Dell Poweredge R710 server.  My virtual machine is Linux SuSE 10, Service Pack 1, the recommended Cisco media platform video software Surveuillance.  .  I try to get my Cisco software to run on the computer, but it requires an IP address from a remote location to access the software.  My IP address that I attributed to VMware is assigned, but when I use the same address and have the x.x.x.x/cisco.vsm.html there is a conflict with the original address assigned to the address that is using VMware to access the server itself.  I'm a newbie and it's all very confusing to me, so I apprecaite little help.

  Is this a problem IP routing or a problem of port assignment?  The Cisco software is supposed to load when I type http:/x.x.x.x/vsms.html in a browser window on the same network.

  Any suggestions?  I did research this for days trying to figure out how to get a simple program to work.

  Thanks a lot for your help!

  Try the URL localhost directly on SuSE http://127.0.0.1/vsmc.html machine if that gets refused then you have configuration problems in the software.

• Help, please! Device drivers system & basic coprocessor are missing after Win7 upgrade

  Please help with under drivers

  Model - dv9500

  (1) system base unit

  Bus 2 PCI, device 5, function 3

  Hardware - PCI/VEN_1180 & DEV_0592 & SUBSYS_30CF103C & REV_12 ID

  (2) system base unit

  Bus 2 PCI, device 5, function 2

  Hardware - PCI/VEN_1180 & DEV_0843 & SUBSYS_30CF103C & REV_12 ID

  (3) coprocessor

  PCI bus 0, device 1, function 3

  Hardware - PCI/VEN_10DE & DEV_0534 & SUBSYS_30CF103C & REV_A2 ID

  Thanks in advance!

  It is always helpful if you post the full product name or product number. You can find it by removing the battery and looking for the label that says p/n. display the string alphanumeric full here in your thread.

  Have you looked into the system of operating systems section in guides stickied for that information?

  Take a reading this post by Member Daniel_Potyrala. Read the latest pages for locations of tutorial and driver.

  #1 is a Ricoh card

  #2 is the Ricoh storage controller

  Your #3 is that a driver Intel Core 2 coprocessor not installed n not question.  Go to the driver download Intel Web page. Find the correct driver from the OS for your chipset/processor and install it.

• Help please! -Update for just the Bills and windows 7

  I have a new PC, I downloaded the update for MYOB bills comes with windows 7, everything was fine until I decided to set up windows live mail to send invoices, I was then unable to print, save or send invoices just.  I had sent banklink accountant so I'm pretty sure that the default value of the mail has been configured correctly.  I decided to uninstall Just bills and download the update only to find an error message - myob Invoicing_web Editor. (3) .exe could not be verified.  I clicked on run. The installation wizard you need to enter the name, organization, and serial number I did, come I clicked Next, it loaded and I clicked on finish.  Another error message-Sorry there is a problem with your game to the top.  MYOB bills just to reinstall, and then try again.  I tried a few times and I am extremely frustrated.  I would appreiciate advice please.

  Since MYOB JustInvoices is not updated through Windows Update, I can't help ut you could always contact the MYOB Support for assistance-online http://myob.com.au/business/customer-service-support-1258090781438

  PS: while you're at it, ask them if MYOB JustInvoices can be used with Windows Live Mail as default mail Client? [1]

  Speaking of Windows Update, is the computer currently fully patched to Windows Update?

  You experience problems printing in Internet Explorer?

  =======================================================
  [1] if MYOB JustInvoices requires a full or an e-mail client MAPI extended , it's not like Windows Live Mail is only a Simple MAPI e-mail client. [Yes, it's very confusing!]

• HELP Please - I paid for a subscription, but it is still showing as a free trial?

  Today, I decided to pay a subscription for the latest Photoshop (Creative Cloud 2015). I bought the monthly pay via Paypal but I didn't a confirmation email and it's only to allow me to use the program as a free trial for 7 days.

  Can someone please advise on this?

  Thank you

  I read that it will take as much as 24 hours for a purchase to show your Adobe account

  Your subscription to cloud shows correctly on your account page?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  If you have more than one email, you will be sure that you use the right Adobe ID?

  .

  If Yes

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  .

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• Help please... Replaced the hard drive of MBP, restored from TM, but the Windows XP virtual machine does not start

  I replaced the 250 GB hard drive in my MacBook Pro early 2009 with a 500 GB drive, it the Mac OS extended (journaled) format and restored from my Time Machine backup.

  Now when I try to start my Windows XP virtual machine (using Fusion 2.0.6... planning upgrade to 3.1.2 but wanted to validate all was well first), I get BSOD, even in safe mode.

  I have my vm separately saved on a network drive data files based on things that I had read before, I do not think that TM backup of virtual machines. However, a friend with a similar setup with more knowledge I think because I could see my Windows XP vm VMWare listed under 'Documents' in Time Machine showing its full size, it has actually saved and there restore it. Apparently he has done this successfully before.

  Should I have partitioned the hard drive? I don't think that my previous drive has been partitioned. Don't know what to do now.

  TIA!

  Katie

  To be clear: you have restored VMs from the disk or network time Machine?  And if the network drive, what backup method you use?  (i.e.: have you just copied engine off the computer virtual package or not?)  Can you copy/restore the virtual machine to the network again drive?  What is a virtual machine that has the error, or other virtual machines have problems?

  Time Machine backup correctly a virtual power off machine. But since Time Machine works automatically, you often will get not a consistent backup unless you do some tricks to make sure Time Machine backup only when you use a virtual machine.  (i.e.: turn on Time Machine only when you're done with the virtual machine.)  Thus, it is normally recommended to exclude the virtual machines from Time Machine and use another method to back up virtual machines.  Your friend is lucky or is only backup virtual machines powered off.

  Should I have partitioned the hard drive? I don't think that my previous drive has been partitioned. Don't know what to do now.

  The Mac player Paritioning is unnecessary unless you use Boot Camp or have required another for the partition.

• HELP PLEASE!  Cache for the Lightroom Preview error

  Hello

  Has anyone ever experienced the following error trying to open Lightroom:

  "" Lightroom has encountered an error when reading of he is seen hiding and need to stop smoking ".

  He said less than smaller writes:

  "Lightroom will attempt to solve this problem, the next time he throws."

  But unfortunately it didn't :-(

  I have uninstalled, reinstalled, restored etc etc...

  Anyone know anything about this?

  Any help greatly appreciated

  Thanks in advance :-)

  Remove the cache

  It is a folder whose name ends with Previews.LRDATA. Remove the entire file

  It is located in the same folder as your catalog file. Do NOT remove your catalog file.

• Need ESXi owns hard drives for the installation?

  I downloaded ESXi for assessment and have problems with the installation.

  Try to load it on a Red Hat Ent. Linux v5 server that has a logical drive 1 TB.

  During the first steps of the installation, it is said that if I keep data on this singular logical drive will be lost.

  Does this mean I need to repartition my raid at 2 logical drives and reinstall RedHat with the ESXi before you start?

  Help, please

  Chris

  ESXi is a bare metal installation. It will not coexist with another OS. Once ESXi is installed, you can install Redhat like OS as a virtual machine.

• Integration of BlackBerry Messenger SDK... Help, please!

  Hey,.

  I am trying to install the SDK of BBM on my PC.

  I followed the instructions on the start following guide: -.

  (1) first of all, I had to update my JDE and JRE of 1.6.14 to 1.6.26 versions so I uninstalled all older versions of Java and installed 1.6.26.The JRE do not settle in the folder by default (JRE 1.6.0_26) but in a folder called jre6

  (2) after I implemented the SDM as indicated in the instructions. I created the shortcut to MDS with the target as required.

  (3) after that I tried to run the MDS, but it did not work because the unlimited encryption settings are not configured. So I replaced the files in the folder "JRE6/lib/Security" with the jce policy files. After that, the MDS worked very well.

  (4) I had already installed the simulators (5.0 and 6.0) so I ran both sim1.bat and sim2.bat in the 5.0 folder. The simulators showed THAT BBM 6.0 has been installed. But after I tried the sim2 guest sim1 BBM and vice versa, it appears just as pending in the BBM and I don't get requests in the invited simulators.

  Can someone please help me solve this problem? I repeated this procedure a countless number of times, but I can't always connect the simulators to the other.

  Additional notes:

  (1) when I opened the simulators, I see some messages in the MDS. So I can assume MDS has been installed properly?

  (2) I cannot browse the internet using browsers on a simulator.

  (3) as when I go to manage connections service status BIS and BES services are indicated as not connected. This means that the installer is not done correctly?

  Help, please!

  For anyone interested, I have solved my problem.

  See pages 5 here:

  http://docs.BlackBerry.com/zh-TW/developers/deliverables/25815/BlackBerry_Messenger_SDK-Release_Note...

  You must change the links in the Simulator

• Can not see the external hard drive to my computer only in devices & Printers I tried many patches & need help please

  I do not see my external hard drive in my computer but I can't in my devices and printers.  I too see the drive in disk management.  There is a lot of data on my hard drive that I need to save. It says that I have to initialize so the computer sees the drive but it clears my data. How to recover data? The drive works and makes no noise. Help, please. I uninstalled the RPG player

  and reinstalled. I've also updated the driver and I still don't see the drive in my computer.

  Hello

  Welcome to the Microsoft community.

  I understand that you have a problem with finding printers and external hard drives in the computer. We apologize for the unhandiness caused to you and appreciate your efforts in trying to solve the problem.

  To help you better I would like to know the details.

  1. What is the brand and model of the computer?
  2. You did changes to the computer before the show?
  3. Have you tried to connect the same external hard drive on another computer?

  I ask you to run the hardware and devices Troubleshooter and check if the problem persists. It is an automated tool that checks the hardware attached to the computer for known problems and provides details on how to correct them.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  I ask you to install optional Windows, including updates updates and check if you are facing the issue.

  Reference http://answers.microsoft.com/en-us/insider/wiki/insider_wintp-insider_devices/how-to-install-and-update-drivers-in-windows-10/a97bbbd1-9973-4d66-9a5b-291300006293

  Keep us updated on the issue to help you better.

• Drive hard keeps fills, using CC Cleaner & Deffrag for a few weeks now. I do go down, & then it fills again! Help, please.

  I'm running Vista 64, SP2 and my hard drive keeps filling.

  I used CC Cleaner and Deffrag program for a few weeks now.

  (just the CC Cleaner on its own takes me awhile because I don't want to delete everything I shouldn't)

  I have moved away from home to the office and checked to see if there are "too many connections (?)" just in case it's something in the process.  Honestly, I can't say if there are too many?

  I know that I don't want to lose the ability to remote into my office... so I leave them alone.

  I wanted to delete some 'hidden' files $Recycle... but am concerned that my operation files original files are mixed in the files?

  Is there a way to return to the top... few of the restoration copies?

  AND... How can I stop this from happening?  I spent hours trying to manage it.

  It comes down, then it fills again!

  Help, please.

  Hello MetisLight,

  Here is a link to another user having the same problem.  Have you tried to try the steps listed?  Please let us know status.

  Microsoft Answers:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/harddrive-filling-up/e9b60b0c-6b9d-4e12-85d9-9a875cc1aa8a

• Please, help me to turn on my Bluetooth device for me.

  OT:

  Activate Bluetooth in Windows 8 Pro

  I had HP for laptop - 15-r264tu in which Windows 8 Pro is installed and everything seems to go well except the device Bluetooth is switch off. I tried searching how to turn on my Bluetooth device and I tried the laptop settings / PC and devices / Bluetooth, but it found only and cannot turn on but failed. Please, help me to turn on my Bluetooth device for me.

  Elvish Hello,

  Thanks for posting your question on the Microsoft community.

  Thank you for details on the question and your efforts to resolve.

  This problem can occur because of lack of permissions in Windows.

  Please make sure that you are logged on as administrator.

  If this does not help, then you can manually download the driver file, take ownership of the file and then try to install it.

  Please see this link:
  "Access denied" or other errors when you access or work with files and folders in Windows
  https://support.Microsoft.com/en-us/KB/2623670

  You can also run the hardware and devices Troubleshooter and check. Please follow these steps:

  a. press Windows + C keys and click on Search.
  b. type Troubleshooting in the search box and click on it in the search results.
  c. click 'show all' and then click 'hardware and devices'.
  d. click on 'Next' and follow the on-screen instructions.

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• I'm so frustrated!  I have CS5 Master Collection.  I want to UPGRADE to CS6 Master Collection.  I want to be on the cloud!  I can't find where to put up-to-date or any CONTACT to ask for help.  It shouldn't be this hard.  HELP Please!

  I'm so frustrated!  I have CS5 Master Collection.  I want to UPGRADE to CS6 Master Collection.  I want to be on the cloud!  I can't find where to put up-to-date or any CONTACT to ask for help.  It shouldn't be this hard.  HELP Please!

  See the link below:

  Creative Suite 6

• Reader Adobe XI updates last week. Reinstalled this morning. All previous saved pdf files are now forms of words asking the conversion? Creates problems for my business. Help, please?

  Reader Adobe XI updates last week. Reinstalled this morning. All previous saved pdf files are now forms of words asking the conversion? Creates problems for my business. Help, please?

  See http://windows.microsoft.com/en-us/windows/change-file-open-program#1TC=windows-7

  Another method: http://windows.microsoft.com/en-us/windows/change-default-programs#1TC=windows-7