OID for PowerConnect 3548

Similar Questions

• Reference Dell PowerConnect 2848 OID for CPU time and memory

  Hi all

  This is my first post in this forum. I searched all the messages that can solve my problems, but I could not find so if there is already an existing post and I couldn't find it please guide me to it.

  My case is. We have a few Dell PowerConnect 28xx switches in our network. We want to monitor things like the CPU, the temperature, the use of the RAM usage. We use Solarwinds IpMonitor monitoring tool. I downloaded the MIB, I could find the download of Firmware from Dell drivers and downloads page. I went through the entire MIB, but I couldn't find an OID for the foregoing.

  So if anyone can help me please what OID is used for usage of CPU and RAM temperature it will really help me.

  Please let us know in case we need more information on my side.

  Thank you

  Frank Moreau

  I did use SNMP on the 28xx but here are some various sensor OID, I used for the N-series, as well as some older models Powerconnect.  I don't know if they will work for the 2xxx, but you can try one or two and see if they work.

  N - Series (FW 6.2 and later versions) temperature OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.0
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.5.1.1

  62xx (3.0.x.x firmware or later-, some may also work with 2.x firmware)
  Temperature OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.3
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.4

  Are the OID to use CPU for N-Series switches
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1 (total free memory)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2 (total memory)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3 (table for the following...)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.1 (index)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (name of the process using CPU)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (% CPU used by the corresponding process)
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.4.0 (cumulation of all the activity of the CPU)
  1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.9 (CPU utilization shows 5 s, 60 s and 300s).

  OIDs memory
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2
  Power supply OID
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.7.1.3
  OIDs of fan
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.2
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.3
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.4
  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.6.1.5

  35xx (2.0.x.x or later firmware)
  Temperature OID
  . 1.3.6.1.4.1.89.53.15.1.9
  . 1.3.6.1.4.1.89.53.15.1.10
  OIDs of CPU
  . 1.3.6.1.4.1.89.1.6
  . 1.3.6.1.4.1.89.1.7
  . 1.3.6.1.4.1.89.1.8
  . 1.3.6.1.4.1.89.1.9
  OIDs memory
  . 1.3.6.1.4.1.89.29.11.1
  . 1.3.6.1.4.1.89.29.11.2
  P.S. The OID
  . 1.3.6.1.4.1.89.35.5.1.1.2
  . 1.3.6.1.4.1.89.83.1.2.1.2
  . 1.3.6.1.4.1.89.83.1.2.1.3
  . 1.3.6.1.4.1.89.83.1.2.1.4
  . 1.3.6.1.4.1.89.53.15.1.3
  . 1.3.6.1.4.1.89.53.15.1.3
  OIDs of fan
  . 1.3.6.1.4.1.89.83.1.1.1.2
  . 1.3.6.1.4.1.89.83.1.1.1.3
  . 1.3.6.1.4.1.89.53.15.1.4
  . 1.3.6.1.4.1.89.53.15.1.5
  . 1.3.6.1.4.1.89.53.15.1.6
  . 1.3.6.1.4.1.89.53.15.1.7
  . 1.3.6.1.4.1.89.53.15.1.8

  for old firmware - if the 35xx above does not work:
  Temperature
  1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.9 (Celsius)
  1.3.6.1.4.1.674.10895.5000.2.89.53.15.1.10

  I hope this helps.

  B

• Y at - it any OID for Windows XP?

  I want to follow my windows XP via SNMP client, is there any MIB file where I can find some OID for Windows XP?

  Hello

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows XP Networking forum.
   
  http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads

  Mau also consult you the following links for more information:

  http://support.Microsoft.com/kb/287547

  http://TechNet.Microsoft.com/en-us/library/cc776379 (WS.10) .aspx

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_snmptopnode.mspx?mfr=true

• RPS-600/700 for PowerConnect 5224/5424 installation procedure

  Hi all

  I bought a unit of RPS-600 and 700 - RPS for the redundancy of the power supply for PowerConnect 5224 unit and 5424 respectively.

  Two questions/doubts came into my mind and I hope that some experts here could specify:
  1. What is the step by step connection rps-600/700 (new procedure) to PowerConnect 5524/5424 (live system) - e.g.: power first rps-600, then rps on rps-600 cable then cable rps on 5524 etc.?
  2. with the step defined above, there is no downtime?

  Thank you!

  See you soon,.
  Elvin

  Here is the link to the user on the RPS700 guide

  http://bit.LY/17YiiCA

  You can plug the switch first RPS, then the RPS to the electric network. There should be no interruption of service.

• need to download OAM/OID for integration of R12

  Hello
  
  
  I'm confused about what to download(OAM/OID) for integration in an environment of R12.
  
  
  Identity management:
  
  http://www.Oracle.com/technetwork/middleware/downloads/OID-11g-161194.html
  
  Identity (11.1.1.2.0) x 86: 1.4 GB Disk1
  
  Then the game patches of the OID 11060980
  
  Jrocket:
  -------
  http://www.Oracle.com/technetwork/middleware/JRockit/downloads/index.html
  
  Download Linux x 86
  
  
  My question is where can I download link below software install OAM 11.1.1.3
  
  
  http://www.Oracle.com/technetwork/middleware/downloads/OID-11g-161194.html

  My question is where can I download link below software install OAM 11.1.1.3

  http://www.Oracle.com/technetwork/middleware/downloads/OID-11g-161194.html

  It is in the same link, under 'Oracle Access Manager WebGates (11.1.1.3.0)'.

  Thank you
  Hussein

• PowerConnect 3548 - change port access mode?

  I'm having a problem with our 3548 P PowerConnect switches.  I guess it's just a procedure, I'm not aware, so I hope I can get help.

  It was necessary to temporarily move several ports to general mode to add access to a VLAN individual.  Right now, I would like to remove this VLAN and only have ports of the switch in question on VLAN 1.  I get a (not unexpected) error when trying to add ports to VLAN 1 (because it is not created by the user, the default VLAN), I tried to simply remove the VLAN ports and switch back them to General.  When I do, I get the following message:

  EXX port: Port does not belong to VLAN PVID as not tagged.

  What command sequence should I return the ports to access the mode and just make sure they're on the VLAN 1?  I guess I should do something about port traffic to not tagged or delete the PVID before returning to the access mode.

  I think I fixed the problem.  If I set the VLAN existing as non-tagged, i.e.:

  "switchport vlan allowed general access Add VLAN unidentified".

  This removes the image of marking and allows me to go back to access the mode on the switchport.   Yet to get used to the command structure; Thank you for putting up with my questions.

• SNMP MIB for PowerConnect X 1000 series

  Hello

  Where can I download SNMP MIB for Dell PowerConnect X 1000 Series switch? I would like to use MIBs updated rather than generic Dell PowerConnect MIBs.

  Thank you!

  Firmware download includes MIB.

  http://Dell.to/1KADEsz

  See you soon

• Good method to restore running, boot and Firmware for PowerConnect 6224 switch

  Hi all

  I have a switch PowerConnect 6224 of production that is configured exactly as I want.  I have a new PowerConnect 6224 switch I want to restore the config is possible?  My goal is to not have to manually enter settings for each single switch.

  I tried a few methods, but they do not seem to work.  If anyone can tell me the correct procedure or point me in the right direction would be great!

  Here's a document on some older switches which explains the process.

  www.Dell.com/.../app_note_12.pdf

  It is different for the 6248 somewhat, but the concept is still the same.

  Copy of the file Image of a server to Flash memory

  Use the command copy of the image - the url of the source to copy an image from a Flash memory server file, use the boot system command to activate the new image.

  Copy of a Configuration file from one server to the running Configuration

  Use the running-config command to copy the url of the source to load a configuration file to a network server for the device running configuration. The configuration is added to the running configuration, as if the commands were typed in the command line interface (CLI). The resulting configuration file is the combination of the running configuration and the loaded configuration file, with the configuration file with priority.

  Copy of a Configuration file from one server to the Startup Configuration

  Use the command copy startup-config - the url of the source to copy a configuration of a network server file in the startup of the device configuration. These commands replace the configuration file starting with the copied configuration file.

  Store the Configuration of starting or running on a server

  Use the command copy running-config destination url to copy the current configuration file to a network server by using TFTP. Use the copy destination-url startupconfig command to copy the configuration file to start on a network server. The copy of the configuration file can be used as a backup copy.

  firmware download also includes step by step instructions on how to upgrade the firmware.

  www.Dell.com/.../drivers

• VLANs for PowerConnect 6224

  Hello

  I bought Dell PowerConnect 6224 & I'm newbie for VLAN management. To put it simply, how can I create two VLANs (vlan 10 - 192.168.10.x/24 & vlan 20 - 192.168.20.x/24) that can communicate with each other without defining the point of gateway for the network servers and workstations to the ip address of vlan?

  Thank you.

  Here is a link to the manuals available for the Dell PowerConnect 62xx:

  support.Dell.com/.../index.htm

  Creation of VLANS

  Console > activate

  Console # config

  Console (config) # vlan database

  VLAN console(config-VLAN) # 10

  output console(config-VLAN) #.

  Console (config) # interface vlan 10

  # Ip address 255.255.255.0 192.168.10.x console

  Console # name Marketing

  Console # end

  console # show vlan

  Creating Ports for PC to connect as a ignorant guest VLAN.

  Console > activate

  Console # config

  Console (config) # interface ethernet 1/e1

  Console # switchport mode access

  Console # switchport access vlan 10

  Console # end

  Enable routing

  To globally enable IPv4 routing on the router, use the command "ip Routing".

  in Global Configuration mode.

  Console (config) #ip Routing

  You will need to create the VLAN as described above.  Then, set the access mode for a port VLAN particular then set the PC with an IP address in the range of the subnet for the VLAN and the gateway as the IP address of the address that you provided for the VLAN on the port.

  Then once the routing is enabled in the world it should allow communication between VLANs and configured different subnets.

  Hope this helps,

• 11g OID for Unix startup script

  Someone at - it script to start and stop the entire stack of OID (11g) that I can use in init.d scripts?

  Is this the bottom?

  ./startWebLogic.sh-Dweblogic.management.username=[insert username] - Dweblogic.management.password = [insert password]

• Configure the IP address for PowerConnect 2724 on existing network

  I tried access the switch using the default IP 192.168.2.1 and can't find it.

  I was literally out of available ports before the purchase/installation of the 2724.

  Our network is 192.168.0.x with a subnet of 255.255.255.0.

  Currently, the managed Mode light is turned off.

  I can access the network/web prior to the switch.

  Can someone tell me where I am / have gone bad?

  How to configure the switch before adding it to the existing network?

  Switches used:

  Reference Dell 2024, 2608, 2724

  NETGEAR FS516

  Thanks in advance.

  
  

• VLAN real PowerConnect base for beginner who does not understand the trunks etc.

  I have several switches Dell powerconnect 3548 and 5548 deployed on my network to install multi that I'm managing their individual DNS names.  now, I've added a voip phone system that works on my network, but to a range of ip addresses completely different to another server.  So, I want all my switches divided into 2 VLANS.  The basic vlan 1 will always manage the switches and all ports and the vlan voip will have its own set of ports on the second VLAN.

  There is no visibility between the VLAN, just different IP addresses different server DHCPd, s so if your clogged in the vlan 1 are you a PC/printer/etc with your own default gateways defined by the field.  If you are connected to one vlan 10 you are a phone and you will get your information from an edgemark server somewhere else.

  so step by step (if you want to give me even better orders) I have actually need it to configure to create a vlan separate and independent who will seek dhcp by an existing voip to its home network device to, while I can still manage my management ip switches.  I understand not all the vocabulary of trunking and I don't know if it needs anything else including marking, because are is all autonomous.  I guess I need a guid for Dummies at vlanning powerconnects.

  VLAN datbase
  VLAN 10
  end

  Interface vlan 10
  name voip
  end

  e1 serial interface, e14
  switchport mode private vlan community?

  Here is an example:

  Console (config) # data vlan

  VLAN console(config-VLAN) # 10

  Output console(config-VLAN) #.

  Console (config) # id vlan 10 voice

  Console (config) # voice vlan Yes add XX

  Console (config) # int 1/0/1 gi

  Console switchport mode trunk #.

  Switchport trunk console # permit vlan remove 10

  Activate console # vlan VoIP

  Console # end

  Here is a white paper for configuration Dell PowerConnect 55xx series switch voice VLAN:

  en.Community.Dell.com/.../Configuring-Dell-PowerConnect-55xx-Series-Switch-Voice-VLAN.aspx

  Page 557 of the CLI Guide begins the discussion for orders of VLAN on the switch 5500 voice.

  http://downloads.Dell.com/pages/manuals/PowerConnect-5548.html

• OID need to run SNMP queries for the CPU usage, etc. in Win XP

  Hello

  I am unable to get the details (CPU Util, Util Swap) of windows using SNMP (SNMP4j.jar) machine. The SNMP service is running on the Windows XP system target. Where can I find the correct OID for windows XP to retrieve these settings?

  Join the code below:

  Import org.snmp4j.CommunityTarget;
  Import org.snmp4j.PDU;
  Import org.snmp4j.Snmp;
  Import org.snmp4j.event.ResponseEvent;
  Import org.snmp4j.mp.SnmpConstants;
  Import org.snmp4j.smi.OID;
  Import org.snmp4j.smi.OctetString;
  Import org.snmp4j.smi.UdpAddress;
  Import org.snmp4j.smi.VariableBinding;
  Import org.snmp4j.transport.DefaultUdpTransportMapping;

  Configure the Snmp object
  private Snmp snmp = null;
  private UdpAddress targetAddress = null;
  private CommunityTarget target = null;
  ResponseEvent responseEvent = null;

  targetAddress = new UdpAddress (10.101.210.127 + ' /' + 161);

  target = new CommunityTarget();
  target.setCommunity (new OctetString ("public"));
  target.setAddress (targetAddress);
  target.setRetries (2);
  target.setTimeout (60000);
  target.setVersion (SnmpConstants.version2c);
         
  SNMP = Snmp new (new DefaultUdpTransportMapping());
              
         
  SNMP. Listen();

  CPU usage code
     
  Command PDU = new PDU();
  command.setType (PDU. (GET);
  Command.Add (new VariableBinding (new OID(".1.3.6.1.2.1.25.2.3.1.4"))); / / percentage of CPU Idle time//.1.3.6.1.4.1.311.1.7.3.1.6.0
  try {}
  responseEvent = snmp.send (command, target);//.1.3.6.1.4.1.2021.11.11.0
  } catch (Exception e) {}
  System.out.println ("Exception:" + e); e.printStackTrace ();
  }
  If (responseEvent.getResponse () == null) {}
  request timed out
  Returns a null value.
  } else {}
  Response PDU dump
  PDU pdu = (responseEvent.getResponse ());
  Output vector = new Vector();
  Output = pdu.getVariableBindings ();
  int val1 = 0;
  Double CPUMemUtil = 0;
  Dim str As String = null;
  Str = Output.get (0) m:System.NET.SocketAddress.ToString ();
  String [] Spstr = str.split("=");
  Spstr [1] = Spstr [1] .trim ();
  try {}
  val1 = Integer.parseInt(Spstr[1]);
  } catch (Exception e) {}
  System.out.println ("An Exception occurred" + e); e.printStackTrace ();
  }
  CPUMemUtil = (100 - val1);
  String OutputMemUtil = Double.toString (CPUMemUtil);
  System.out.println ("CPU usage" + OutputMemUtil);

  Thanks in advance,

  Souto

  Hello

  Questions like these are much better handled in the TechNet IT Pro Forums.

  My moderator tools cannot transfer messages on Windows forums, please re - ask you question there.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Follow-up of the CPU of a Dell N2024P OID

  Hello

  Is it possible the workload monitor CPU on this model?

  If this is the case, what OID would give me information?

  Thank you.

  I think that all the CPU utilization OID for N-Series switches are de.1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.   Here are some examples...

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.1 (total free memory)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.2 (total memory)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3 (table for the following...)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.1 (index)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (name of the process using CPU)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.3.1.2 (% CPU used by the corresponding process)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.4.0 (accumulation of CPU)

  . 1.3.6.1.4.1.674.10895.5000.2.6132.1.1.1.1.4.9 (CPU)

  B

• PS6510 and Volume of OID

  We use a third party to monitor the disk space and been application is trying to get our 6 volumes monitored using SNMP. I managed to identify the Volume OID (1.3.6.1.4.1.12740.5.1.7.1.1.8.), which gives us the total size using eqliscsiModule.mib

  But can't seem to identify the correct OID to read Volume disk used/free space.

  Can anyone help?

  Thank you.

  If I'm not mistaken this is caused by the fact that the EqualLogic provides block systems and does not know what is actually being used on your file system so it doesn't have an OID for the use of the file system.

  We had the same wish for our VMware volumes for which I had followed their statistics hollow vCenter because she doesn't know how much is actually being used.