Hosting devices USB with my STOR problem. E TV

Similar Questions

• Device USB-6009, not found problem

  Hi all

  So my VI and USB-6009 worked fine until recently.  I noticed the VI was read or graphing correctly the analog input channel information.  My firmware is up to date, but I noticed a problem.  In Isdaq, he will recognize the USB-6009 case is connected, then when I start my VI and to stop it, I double check Isdaq for my device and it doesn't recognize any device.  I have to unplug the daq and reconnect to Isdaq to recognize the usb-6009 case again.  But whenever I start my VI, it does not collect all the data and makes the unrecognizable device.  Do you know what could be the problem?  Is attached the VI I ran in case you want to watch.  Its working fine so far.

  BTW, I'm under Labview on Mac OS X

  Thanks for the help!

  Hello Solis,

  I recommend you to make changes to the parallel tasks to use the cluster of the error to force the order of execution, given that NEITHER-DAQmx Base is not multi-thread safe (review NOR-DAQmx Readme). Please check if this alleviates the problem.

  Best regards

  M Ali

  Technical sales engineer

  National Instruments

  www.NI.com/support

• Apple Mobile Device USB Driver has not passed Logo testing for compatibility with Windows XP, I ran the suggestion to "fix" 925196 that it still does not work. What can I do else?

  Bought the iPhone 3 g (not 4) trying to run the material but get the following error: Apple Mobile Device USB Driver no has not passed Windows Logo testing to verify compatibility with Windows XP continues the installation of this software may impair or destabilize the functioning of your system.

  Windows XP Service Pack 3 is running.

  I ran the 'Fix - It' 925196 solution, but the problem could not be solved. What is a malware problem?

  Hi deanie3,

  We will check if the following is useful.

  Method 1: Run the next Fixit and check the issue.

  Hardware devices do not work or are not detected in Windows

  Method 2: Follow the steps in the below article mentioned to see if it helps.

  You cannot install some programs or updates

• Windows has stopped the device because it has reported problems. Code 43 with generic bluetooth adapter.

  Windows has stopped the device because it has reported problems. Code 43. Something with the generic bluetooth adapter. What should do?

  Original title: Please help

  Hi JovanaNesic,

  One of the motors controlling the unit notified the operating system that the device has failed in some way.

  Try to run the hardware troubleshooter and check what the problem is and fix it accordingly.

  Follow the link below a convenience store opened.

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  If you have already run the Troubleshooting Wizard, you can view the documentation for the hardware for more information about diagnosing the problem.

• Windows has stopped this device (USB 2.0 Flash Disk) because it has reported problems. (Code 43)

  I have USB 2.0 Flash Disk of Orchid do. This device worked perfectly until I downloaded from MS Download Center "Microsoft USB Flash Drive Manager" and tried to install this. Although the program has not installed message stating that "this program is not applicable for the Version of Windows installed on your computer", but it made my flash drive stop working after the installation fails. Now, I always get error message this device driver was not successfully installed (USB device not recognized) and your USB device has malfunctioned or Windows has stopped this device because it has reported problems (Code 43). In the Device Manager under USB controllers, the device is listed as "unknown device". I tried most of the methods described in the forum, but so far none of them has proved to be successful. I will ask members of the forum of good want to let me know if my device itself has developed some defect (hardware failure) or is - having something to do with driver has been corrupted (software compatibility problem) and if so what is the corrective treatment / necessary rectification. Furthermore, I must say here that I am running Windows 7 RC OS version on my computer. Thank you best regards &.

  Hi ALOK CHANDRA SINGH,.
  If none of these solutions will not help you check this thread.

  If you want to say thanks to someone just click on Vote as useful (i.e. under each avatar of the user).

  If your issue is resolved, please indicate then your wire is with solution.

• Error "Windows has stopped this device because it has reported problems. (Code 43) "when I try to plug my mouse optical usb into the USB port.

  Original title:

  First here is my card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02479651&cc=ca&dlc=en&lang=en&lc=en&product=4299342 desktop pc
  and my mobo card http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02560084&tmp_task=prodinfoCategory&cc=ca&dlc=en&lang=en&lc=en&product=4299342
  (running windows 7 x 64 and not changed all my pc hardware so everything on the Web page is true)

  in any case, when I try to plug my mouse optical usb in the port of e/s (usb port) on the front panel (which supports usb 2.0) a notification pops up saying
  "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it. Help to solve this problem, click this message. "
  so I click it and and called up pop-up windows
  "the usb device not recognize."
  display 1 unknown device. Link to the image: http://img38.imageshack.us/img38/3579/usbdevicenotrecognizewi.jpg
  Then I double click on it, next pop up another window called "unknown device properties" and under "device status", he said:
  "Windows has stopped this device because it has reported problems. (Code 43) »
  Link to the image: http://img204.imageshack.us/img204/8597/unknowndeviceproperties.jpg

  Also the same things happen when I plug in usb, keyboard , but not when I plug a flashdrive usb 2.0 without notification or anything pop up.

  Here's what I'm trying to fix it but ended up with saying it was installing the device, installation failed and getting the error failed and unrecognized again...

  • Plug my optical mouse on my other ports and it works perfectly fine (to see if its working)
  • Plug the mouse (in the wrong port), went to Device Manager and uninstall the unknown device, reboot with usb plug in and have the connection to the internet (not decided)
  • Uninstall all devices under USB bus controllers in the Manager device and rebooted with mouse in internet connection (not decided)
  • Went to device manager expanded bus controllers USB right-click on power management all the device label "usb root hub" click and uncheck the box "allow the computer to turn off this device to save power" and reboot (do not set)
  • Open the normal startup in msconfig (system configuration) selected and restarted (did not set)
  • Shut down the computer, disconnect the plug, unplug all the devices connected to all IO ports (usb port specifically) and my desktop pc has left alone for an hour and a half and start it to the top after with everything back plug (mouse in the wrong port) (has not set)

  Note: when the mouse is connected to the usb port it is light on substance, but its does not (not flashing do not and when you move, mouse is frozen on the monitor)

  Hello

  The results highlight the drivers. It is best you contact HP support and get all the latest device drivers.

  http://WWW8.HP.com/ca/en/support-drivers.html

• Windows has stopped this device because it has reported problems. (Code 43) A request for the USB device descriptor has failed.

  Separated from this thread.

  Hello

  I'm faced with the same question. I went to settings of your laptop and ran the recovery, but it did not help. I went to Device Manager and I noticed an error: Windows has stopped this device because it has reported problems. (Code 43) A request for the USB device descriptor has failed. Tried to fix that with an alternative of Microsoft Community (http://support.microsoft.com/mats/hardware_device_problems/?wa=wsignin1.0), but the issue could not be resolved. I don't know if they are related, but I think so. Spent so much time trying to solve this problem and would be really grateful for the help. Have had the computer for less than 3 weeks...

  Ewa

  Hi Ewa,

  Thanks for the reply.

  I suggest you to update the drivers for the chipset of your computer and check if it helps. You can use the link below. Select the appropriate component and the operating system from the list. The link given below is for Lenovo 11 2 yoga, if you have any other device then please provide us with the exact model number or select the correct model number.

  http://support.Lenovo.com/us/en/products/laptops-and-netbooks/Yoga-series/Yoga-2-11-notebook-Lenovo?c=1

  As you mentioned that the other two USB ports work correctly, according to me is not a problem with the driver. It seems to be a hardware problem.

  Let us know the status.

• Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  Kev2012 wrote:

  Someone at - he had problems with 9.2.1 and pairing Bluetooth devices?  My iPhone will not be connected or pair of devices.  Devices to recognize the iPhone 6, but the will of the iPhone 6 does not recognize the device.  Is there a problem with 9.2.1?

  It would depend on what you're trying to link to?

  Here are the supported Bluetooth profiles an Apple device can connect to iOS: Bluetooth profiles supported - Apple Support

• My 4 GB USB shows this error "Windows has stopped this device because it has reported problems. (Code 43) ». How do slove this problem pls tell me

  My 4 GB USB shows this error "Windows has stopped this device because it has reported problems. (Code 43) ». How do slove this problem pls tell me

  Try the USB device on another computer.  If you get the same error in another computer, then the unit has probably missed and the files that it contains are lost.

• USB key. Out without button to safely remove. Windows has stopped this device because it has reported problems. (Code 43)

  I need help to be able to reuse the disk.  The drive is not displayed when inserted or displayed in Device Manager.  Problem started when it was deleted without being stopped properly first.  Arrive in a Vista machine.   Windows has stopped this device because it has reported problems. (Code 43).  I download programs to repair files and other things with Microsoft Partners do not anything to solve this problem.  Any help will be appreciated.  I've caused the problem, but is the difficulty of it.

  Try to put the device in another computer.  If you get the same message, then it looks like you have destroyed it by unplugging it wrong.  It doesn't happen often, but you would not be the first person that I heard what is happening to.

• XP host block when Xp on device USB Connect to VM

  Hello

  When I "Connect (disconnect from the host)" a USB (usb Ultrapro of the Rainbow):

  (1) key light off ("it was disconnect from the host")

  (2) light button on (it is connect to VM)

  (3) after a few seconds a host with a blu screen crash

  Host config: XP - PRO SP3 with AMD Athlon 64

  VM Config: XP - PRO SP3

  Virtual MACHINE created with VMWARE WORKSTATION 6.5.3.

  VM was played with WMPLAYER 3.0.0 - 203739, aprΦs the dΘmarrage of (1) I have updated VMTOOLS (ver 8.1.3)

  Thanks in advance to anyone who can help me.

  Concerning

  DCUBE

  read the usb-related things here http://sanbarrow.com/workstation-faq.html

  ___________________________________

  VMX-settings- VMware-liveCD - VM-infirmary

• measurement of input frequency TTL with sheet metal entered on a device USB 6363

  Hi all

  Is there a simple LabView vi to measure the frequency of entry TTL cable for the entrance/s, four counters available on a device USB 6363?  I have LabView 2014 FDS installed. I guess using 2 4 meters would be better than 1 for 32-bit resolution, correct?

  Thank you

  John

  Hi jac2015,

  There is an example of a measure of frequency located in LabVIEW help-> find examples-> material-> DAQmx entry and exit-> entrance of counter-> meter - reading pulse width and frequency (continuous) .vi

  Take a look at it and see if that helps. There is also a very useful white paper on considerations to make when measuring frequency, you can find here:

  «Measures of frequency: practical Guide»

  http://www.NI.com/Tutorial/7111/en/

  The main considerations is how often should the signal you want to measure?

  I hope this helps!

• State of the device, Windows stopped the device because it has reported problems (Code 43)

  A usb driver for microsoft

  Windows has stopped the device because it has reported problems (Code 43) Standard USB HOST Controller, location of port #0002 Hub_ #0005

  Right click on desktop, select Properties.  On the next page, top left click on Device Manager.

  Scroll down the page until you come to the Universal Serial Bus Controllers and double click on this.

  Uninstall ALL USB host controllers. (Remember that when you have finished the last of them, your keyboard and mouse may not work!)  Restart the PC.  Windows should then pick up the controllers & install the correct drivers.  The only time where it will not install the drivers is when the USB host controllers are physically damaged.  In this case, the fastest and cheapest method is to buy a USB PCI card which fits directly into a PCI slot on your motherboard and will come with three or four USB 2.0 ports.

• I think Windows has stopped this device because it has reported problems. (Code 43) when connecting iPod to the PC.

  Original title: Code 43 problem

  iPod is no longer detected when plugged to the USB port.  Instead, I get the following error message: "Windows has stopped this device because it has reported problems. (Code 43) »

  Crisis averted!  On another head shot... I thought that maybe the problem could be in the sync cable since the Apple store employee had no problem with the iPod.  I bought a new cable and the computer immediately recognized my iPod.  The old cable is now in the trash.

  Thank you for your help.

  Bob

• Transcend storage device when connected gives error "Windows has stopped this device because it has reported problems. (Code 43) »

  Original title: Windows has stopped this device because it has reported problems. (Code 43) ».

  Hi, I have a storage device 'Transcend', but when I connect it it gives me "Windows has stopped this device because it has reported problems. (Code 43) »

  . in the last ididnt have had problems with this unit. what I can do.

  Shirly

  Hello

  1. What is the brand and model of the device of Transcend storage?

  2. other USB devices work on your computer?

  Error code 43 indicates that one of the motors controlling the unit notified the operating system that the device failed in some way.

  Method 1:

  Step 1:

  I suggest you try plug the storage device Transcend to another computer and check if it works.

  Step 2:

  Also, try to connect the Transcend storage device on another USB port and check if it's work (which you know are working perfectly).

  Method 2:

  You can run the diagnostic Fixit tool. Check out the following link.

  Hardware devices do not work or are not detected in Windows http://support.Microsoft.com/mats/hardware_device_problems/

  Method 3:

  You can check after uninstalling and reinstalling the USB controller. Follow the steps.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (d) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows 7 will automatically reinstall all USB controllers.

  Reference:

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices
  Note: the information provided in the article mentioned above are applicable to Windows 7 too.

  Method 4:

  You can try to install the latest drivers for the storage device Transcend on the manufacturing site and check if it helps. Check out the following link.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  See also:

  Install a USB device

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  Code 43: Windows has stopped this device because it has reported problems

  http://TechNet.Microsoft.com/en-us/library/cc725873 (v = ws.10) .aspx

  It will be useful.