How to configure the VPN for Xperia phones

Similar Questions

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• How to configure the vpn using two segments in a tunnel?

  Hi guys,.

  Please help me how to set up two segment in a vpn tunnel. Our client has two segments which is 10.15 and 192.168. We have already established VPN connectivity. We can ping the 10.15 segment, but we can not ping 192.168. Attached is the sample configuration.

  crypto ISAKMP policy 1

  BA 3des

  preshared authentication

  Group 2

  ISAKMP crypto key xxxxxx address 11.11.11.11

  !

  86400 seconds, duration of life crypto ipsec security association

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  map SDM_CMAP_1 1 ipsec-isakmp crypto

  Tunnel description

  defined peer 11.11.11.11

  Set security-association second life 28800

  game of transformation-ESP-3DES-SHA

  match address 102

  access-list 101 deny ip 192.168.202.0 0.0.0.255 host 10.15.0.177

  access-list 101 deny ip 192.168.202.0 0.0.0.255 host 192.168.30.174

  access-list 101 permit ip 192.168.202.0 0.0.0.255 any

  access-list 102 permit ip 192.168.202.0 0.0.0.255 host 10.15.0.178

  access-list 102 permit ip 192.168.202.0 0.0.0.255 host 192.168.30.174

  Here is the extended ping.

  Router #ping

  Protocol [ip]:

  Target IP address: 10.15.0.177

  Number of repetitions [5]:

  Size of datagram [100]:

  Timeout in seconds [2]:

  Extended commands [n]: y

  Source address or the interface: 192.168.202.3

  Type of service [0]:

  Set the DF bit in the IP header? [None]:

  Validate the response data? [None]:

  Data model [0xABCD]:

  In bulk, Strict, Record, Timestamp, Verbose [no]:

  Scan the range of sizes [n]:

  Type to abort escape sequence.

  Send 5, echoes ICMP 100 bytes to 10.15.0.177, wait time is 2 seconds:

  Packet sent with a source address of 192.168.202.3

  .!!!!

  Success rate is 80% (4/5), round-trip min/avg/max = 172/172/172 ms

  Router #ping

  Protocol [ip]:

  Target IP address: 192.168.30.174

  Number of repetitions [5]:

  Size of datagram [100]:

  Timeout in seconds [2]:

  Extended commands [n]: y

  Source address or the interface: 192.168.202.3

  Type of service [0]:

  Set the DF bit in the IP header? [None]:

  Validate the response data
  ? [None]:
  Data model [0xABCD]:
  In bulk, Strict, Record, Timestamp, Verbose [no]:
  Scan the range of sizes [n]:
  Type to abort escape sequence.
  Send 5, echoes ICMP 100 bytes to 192.168.30.174, wait time is 2 seconds:
  Packet sent with a source address of 192.168.202.3
  .....
  Success rate is 0% (0/5)
  And here is the result of its crypto isakmp.
  Crypto ISAKMP router #show its

  status of DST CBC State conn-id slot

  11.11.11.11 22.22.22.22 QM_IDLE 1 0 ACTIVE

  And here is the encryption session.

  Router #show crypto sessio

  Session encryption router #show

  Current state of the session crypto

  Interface: FastEthernet0/0

  The session state: UP-ACTIVE

  Peer: 11.11.11.11 port 500

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 192.168.30.174

  Active sAs: 2, origin: card crypto

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 10.15.0.177

  Active sAs: 2, origin: card crypto

  And here are the details of the encryption session.

  Router #show crypto session detail

  Current state of the session crypto

  Code: C - IKE Configuration mode, D - Dead Peer Detection

  K - KeepAlive, N - NAT-traversal, X - IKE extended authentication

  Interface: FastEthernet0/0

  The session state: UP-ACTIVE

  Peer: 11.11.11.11 port fvrf 500: (none) ivrf: (none)

  Phase1_id: 11.11.11.11

  DESC: (none)

  IKE SA: local 22.22.22.22/500 remote 11.11.11.11/500 Active

  Capabilities: (None) connid:1 life time: 23:44:02

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 192.168.30.174

  Active sAs: 2, origin: card crypto

  On arrival: dec #pkts'ed drop 0 0 life (KB/s) 4568454/27867

  Outbound: #pkts enc'ed 4 drop 1 life (KB/s) 4568453/27867

  FLOW IPSEC: allowed host 192.168.202.0/255.255.255.0 ip 10.15.0.177

  Active sAs: 2, origin: card crypto

  On arrival: #pkts dec' 8 drop 0 ed life (KB/s) 4591368/27842

  Outbound: #pkts enc'ed 8 drop 2 life (KB/s) 4591368/27842

   

  Hello

  Your side has 192.168.202.0/24 and you are trying to PING 10.15 successfully but not 192.168.30.174

  Check that the ASA has a route to 192.168.30.174 pointing to the external interface.

  Also check that the customer has defined the 192.168.30.174 as part of the VPN traffic correctly.

  Federico.

• How to configure the adapter for network WRT54G wireless

  I downloaded the driver for a tenda usb adapter.  What else should I do to connect to the network WRT54G? I am currently connected via an ethernet cable. Running Windows/7.

  TIA,

  Phil

  OK, I found out how locate network and connect. The only problem was that I used the password instead of the key WEP.

• How to configure the switch for JMS bridge

  Hello
  
  I tried with the selector option when working with several bridges, here is the scenario that I applied.
  
  Created five queues ( Q1, Q2, Q3, Q4, and Q5 ) and configured JMS bridge Destinations with each queue with the factory of unique connections ( CF1, CF2, CF3, CF4, and CF5 ) and baptized as D1, D2, D3, D4 and D5.
  Then created JMS JB2 bridges with D1 source and destination as D2. Similarly the JB3 as D1-D3, as D1-D4 JB4 and JB5 as D1-D5.
  And sector for each of the JB2 JB3 and JB4 JB5 as two, three, four and five respectively and reboot after the changes.
  
  Now I expect the following scenario to work
  By pushing the message to Q1/CF1 with two in the content of the message, so wait for the message to be delivered to Q2/CF2 through JB2, but messages is not moved by JB2.
  Similarly, message pushed to Q1/CF1 having three in the content of the message, so waiting for the message to be delivered to Q3/CF3 by JB3, but messages is not moved through JB3. Similar behavior for other messages with four and five in the content of the message.
  
  In the bridge configuration, selected QOS as "Atmost" - once.
  
  Note: all configurations were conducted in the same field and the WL version is 10.3.6.0 *
  
  The example message I am pushing to Q1/CF1 say 'two Test Data'* and expect to reach the queue Q2/CF2
  
  Concerning
  Venkata Madhu
  
  Published by: vv * Sep 12, 2012 13:05

  JMS selectors work normally om jms headers and not on the message.

  In my previous post, I see that WebLogic provides an extension "SELECTOR xpath" in this area, although I recommend using standard selectors when possible. See my previous post for more information on the syntax of the selector, etc.. The best resource on selectors is the javadoc for javax.jms.Message (http://docs.oracle.com/javaee/5/api/javax/jms/Message.html).

• How to configure the site for several vpn site

  Hello

  We are in the process of upgrading the IT infrastructure n/w. Our headquarters is home to all servers. I want to establish a vpn between our head office and our 4 stores connectivity.

  Head offfice LAN - 192.168.1.0/24

  Remote Desktop

  1 LAN 1 - 10.1.1.0/24

  2 LAN 2 - 10.1.2.0/24

  3 LAN 3 - 10.1.3.0/24

  4 LAN 4-10.1.5.0/24

  I want to implement the ipsec through our internet vpn. An example of a config would be useful. Thank you

  Not very easy to find an example of a config...

  http://www.Cisco.com/en/us/Partner/Tech/tk583/TK372/technologies_configuration_example09186a0080094525.shtml

  But you have to ORC.

  Federico.

• How to configure the proxy for firefox androidversion?

  How to set parameter for android version of firefox?

  Thank you

  Hello

  I have had a look and found this page that should help you.

  If this is not the case please come back here and we'll see what we can do to help.

• Satellite Pro U400: How to configure the VLAN for the Marvell Yukon LAN control.

  Hi all
  I need to access the 2 VLANS with the controller LAN Marvell Yukon 88E8072 for my Satellite Pro U400. I installed the necessary Configuration utility network Marvell tell me after installation, VIRTUAL local network settings must be mounted in the Device Manager (Windows 7, right click on computer, properties, click device/network management adapters/double on Marvell Yukon 88E8072 PCI-E Gigabit Ethernet Controller), I can't find a thing to configure here but wake-on-LAN.

  Any suggestion? Thank you!

  Michael

  Hello

  I think that in this case, you can use a network switch.

• How to configure the network for Windows XP boot

  I have a laptop from nec.
  the cd player does not work and usb either.
  It has an ethernet jack, but I don't know how to set up at the start of the network
  Please help thanks

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• How to configure the DDC for testing?

  Hi all

  I would like to implement Cisco Secure Desktop in our WebVPN configuration, but I need a way to set up and test without making our existing of WebVPN users.

  It seems to me that if I create a Windows with a criterion that * only * my machine test matches, all other users will fail. If I activate the features "when the location corresponding fails", current users won't see a difference.

  Is this correct? Furthermore, with this configuration, VPN tent making out the CSD software when users connect?

  All advice is appreciated.

  Thank you

  -Steve

  Yes, existing users will not see a difference "when the corresponding location fails. This option "what corresponding location fails" helps Windows customers use VPN to surf the web as a minimum connection option, if the client computer does not match any of the criteria of the configured locations.

• How to configure the VLAN for Cisco SG500 - switch 28

  Hello

  First of all, it's my first post here, I hope that someone can help me and please be patient because I am very little known.

  OK, so let me explain to you the scénarion I face and I hope someone can help me.

  We have a Cisco SG500 - 28 port gigabit switch in our workplace.

  Our goal is to create 3 VLANs and separate networks between the various departments.

  Vlan1 (which is the default VLAN in the switch)-will be used for the COMPUTER service and management.

  VLAN100 - will be used for business.

  VLAN200 - will be used for clients who need to connect to internet via WiFi.

  I created VLAN100 and VLAN200, and VLAN1 is there by default.

  I want to use port 13 for VLAN200 and to connect the-Wifi access point there.

  The uplink is in port 25.

  I would be happy if you could explain things first to a more general, abstract level, and then we can look at the specific scenario that we have.

  SG500 Cisco - 28 Gets a Sophos UTM 9 router internet.

  I need to take care of the inter - VLAN routing so, subnet and DHCP

  Thanks in advance,

  Sincere greetings,

  D

  Hi Desmond, looking at this DHCP pool it looks correct.

  For the second part, you waant VLAN 200 only work on VLAN 200, that's fine. So if you have an access point, and everything on the VLAN 200 connects to the access point, you can make an access to this list. The access list is entered only, which means the inbound interface.

  So if you have a gateway connecting to #1 port. You'll need to build the access list and apply it to port number 1. That's assuming you make a list of access 'decline' subnet source IP of VLAN 200 destined for the other subnet, that you do not want access.

  The image on another post to fill out your reference numbers, then for the ACL link, it should be placed on the interface VLAN 200 first comes to the switch (IE, the port the access point connects, make sure that you choose to bind by port instead of per VLAN)

  -Tom
  Please mark replied messages useful
  http://blogs.Cisco.com/smallbusiness/

• How to configure the application for child object View?

  I have a hGrid standard layout. Two display objects are present, sign in using the link display. I need to define where clause in the child View object. The changes themselves do not appear when I put the where the clause. Also when I try to extract rowCount returns 0 for child View object. But I'm able to get the parent View object value. Any suggestions please.

  Hi Shrikant,

  Thanks for your replies. I was able to find a solution. Was able to achieve thanks to the functionality of the rowset.

  Kind regards
  Pradeep

• How to configure the settings for both tables?

  SELECT GM. GRNNO, GM. GRNDATE, SUM (GS. APPROVED), SM. ISSUENO, SM. ISSUEDATE, GS. ITEMCODE, SUM (SS. ISSUEDQTY)
  OF GS, SM IMS_ISSUEM, GM IMS_GRNM, SS IMS_ISSUES IMS_GRNS
  WHERE GM. GRNMSERIAL = GS. GRNSSERIAL
  AND SM. ISSUEMSERIAL = SS. ISSUESSERIAL
  AND GM. POSTED = 'T'
  AND SM. POSTED = 'T'
  AND GS. ITEMCODE = SS. ITEMCODE
  AND GS. ITEMCODE ='01-01-02-019'
  AND *.
  GM GROUP. GRNNO, SM. ISSUENO, GM. GRNDATE, SM. ISSUEDATE,
  GS. ITEMCODE STOPPED BY GM. GRNDATE, SM. ISSUEDATE;
  
  Here, I have to select the data in the tables between two named parameters: P_1 and: P_2.
  the column date of IMS_GRNM is named GRNDATE.
  the column date of IMS_ISSUEM is named ISSUEDATE.
  How to set these parameters?

  I think what you need is
  Where table1. Column1 between: p1 and: p2
  and table2. Between Column2: p1 and: p2

• How to configure the bluetooth with Kyocera android phone connection to share photos, music & video files

  Original title: Windows 8 Configuration bluetooth with Kyocera android phone?

  Configuration of bluetooth of Windows 8 with Kyocera android phone?  I got a laptop with bluetooth Tech. How can I set up a connection and share photos, music & video files?

  Hey GQ - Jon'Jon,.

  Make sure that Bluetooth is enabled on the computer as well as your Kyocera android phone.

  Make sure that the phone is paired with your computer.

  For information about how to configure the Bluetooth with Kyocera android phone connection to share photos, music & video files, it would be better if get you in touch with Kyocera phone support for assistance. Please see the support link:

  http://www.Kyocera-Wireless.com/support/phone/

  Please feel free to respond if you face problems with Windows in the future.

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140