How to enable a wireless connection in Windows 7

Similar Questions

• How would enable remote desktop connection and asking for help?

  How would enable remote desktop connection and asking for help?

  Do you mean on this site?  Sorry, but we don't do that.  We do not have the software required to make the connection (it's too expensive to buy personally) and even if we did we would not get in this practice.  We work by display.

  If you mean for someone else to help you, here is the procedure: http://www.howtogeek.com/howto/windows-vista/turn-on-remote-desktop-in-windows-vista/.

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• How to enable the remote desktop on windows 7 because it is missing in system properties | using Remote tab

  How to enable the remote desktop on windows 7 because it is missing in system properties | tab use remotely.

  I am running Windows 7 Ultimate edition with service pack 1.

  I used to connect my mac via the desktop tool to remotely (2.1) on my mac to my pc windows 7.

  Now, it does not.  Check the services of windows 7 I have ensured that all the remote control * services are enabled, but I still do see the Remote Desktop option in system, under the remote settings properties.

  Any help would be appreciated.

  MasterJay1

  Click Start, click Help, and then type this phrase in the search box:

  enable remote desktop

  Article 5 will have explicit instructions for the task.

• Intermittent problems of wireless connection in Windows 7 Ultimate

  I recently bought Dell Studio XPS 1645 Windows 7 Ultimate edition. I am facing a frustrating problem with Wi - Fi. The connection is down and reconnect. I have the adapter Intel Wireless 5300 AGN and a router Dlink Wireless G I tried to update the latest drivers from Intel (Driver Version: 13.0.0.107), disabling IPv6 for all network interfaces, configuration of the wireless adapter to only use IPv4 and so on. I have 2 other systems with XP Professional on my home network. As soon as I start my Windows 7 laptop, the chaos begins. The router restarts every few seconds, other disconnected systems and so on. I have not found so far any solution on the internet that could solve this problem.

  Other observations that may help to understand my problem:

  1. once my wireless adapter disconnects, the ping my router fails. It tells me whenever my system is asking for a new IP address.

  2 Event Viewer displays multiple entries, which indicates that the DHCP could not get an address. The error looks like as follows:

  The lease of the IP address 192.168.0.100 to the network with the network 0x00216A934EE2 address card has been refused by the 192.168.0.1 DHCP server (the DHCP server sent a DHCPNACK message).
  

  It gets an IP address later, but I do not understand why my adapter tries several times to get a new address every few seconds.
  DHCPNACK is the negative acknowledgement which router returns Win 7 DHCP client. I believe is that the client requests an address that is not available. Why would be client DHCP running on Windows 7 this?

  3. I have a D-Link WBR-1310 wireless router G with the latest firmware. Web sites of the reports that it is compatible with 32 and 64-bit Windows 7.

  4. I see no problems with the wired connection.

  As I type this, which could take a few minutes, my wireless connection rolled 7-10 times. All ideas, experts?

  If you need more information, let me know.

  I was able to find the main cause of intermittent disconnections on wireless interface. According to the information I have collected on internet forums and my research, I did as a result of configuration changes that have stabilized the connection. These settings work when you have N wireless adapter and a B/G Router:

  The wireless adapter settings:
  
  The driver for the most recent driver update.
  Access the properties of your adapter wireless network and sharing Center.
  Click on "Configure" and select the "Advanced" tab Make sure the following is in place:

  1 channel 802.11n for bands of 2.4 and 5.2 width are set to 'Auto '.
  2 disable 802.11n Mode
  3. Ad Hoc channel 802. 11b / g should be 1 or even that you have configured on your router.
  4. Ad hoc QoS Mode, keep WMM disabled - disable the router too. My wireless connection is stable once I made this change.
  5 fat Channel intolerant - disabled
  6. mixed mode protection - RTS/CTS enabled
  7 roaming aggressiveness - the lowest
  8 flow Enhancement - active
  9 transmitting the power - low
  10 mode wireless - 802.11 g

  Uncheck the box "Allow the computer to turn off this device to save power" on the tab "power management."

  Other Configurations:

  1. disable IPv6 completely. Uncheck 'Internet Protocol IPv6' in the wireless connection properties window. Repeat this for every other network connection you have.
  2. make sure you have the latest firmware installed on your wireless router.
  3 CTS Mode should be disabled in the configuration of your router 'Advanced Wireless' auto and WMM function.
  4. use only the WEP or WPA Wireless Security. Other methods have problems with 802.11n adapters.
  5. do not disable broadcasting of the SSID of your router. You don't need when your network is secure.

  I hope this helps.

• How to enable multiple audio output on Windows 7? Speaker and headphones play audio different...

  How to enable multiple audio output on Windows 7?  In Vista and XP it did automatically... I'm running Media center and Media player at the same time.  And plugged in a USB headset.  Media Player will automatically play through the headset and Media Center will go to the speakers.

  Why this feature is LEFT?

  Hi jibberz

  Welcome to the Microsoft Answers Forum!

  Unfortunately, several audio output is not a supported feature in Windows 7.  You may, however, check with the manufacturer of material for possible programs for that purpose.

  To work around the problem, try the steps listed in the link below and check: http://social.technet.microsoft.com/Forums/en-US/w7itprogeneral/thread/b1d1acac-1f21-4d23-8d68-98964d67c2c7

  For any comments, you can see the link: https://connect.microsoft.com/

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP officejet 6800 e all on one: how to enable direct wireless printing

  Hello world
  How to enable direct wireless printing because my printer saying me that its disabled and I need to contact s Adminitrator or the person who installed the printer, which is me I did it by myself.
  So what is the solution pleaaaase?

  Hello and welcome to the HP support community!

  Press the "wireless Direct" icon on the control panel for your printer.

  Should look like this:

  If you press and hold down for 3 seconds, it should print the password to your devices (if the security has been selected).

  WyreNut

• I have windows 7 and how to remedy a wireless connectivity problem when it; s a problem when it has detected the wireless adapter or access point

  I have windows 7 How to deal with a problem of wireless connectivity. The problem according to the diagnosis of computer's wireless adapter or access which was detected point

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

  I had to run the removal of McAfee Development tool a few times before and it caused a problem with the license if the PC was not connected to the internet during the abduction. Due cat of McAfee support reset their files in order to allow the relocation-reactivation. Here is their link cat - McAfee - media contains the link to the cat

• HP 15-AC044TU: how to enable the wifi/connection wireless network in my laptop HP 15-AC044TU win-7 64-bit

  I can't activate the network wifi/wireless connection on my laptop HP 15 - AC044TU win-7 64-bit. I found no adapters wireless network / wifi drivers on the hp site. where can I find it? the key that is used to toggle the wifi?

  Please solve my problem FSA.

  Thank you.

  Hello:

  You need these drivers for W7 wireless and bluetooth for your model...

  Network controller (wireless card):

  FTP://FTP.HP.com/pub/SoftPaq/sp71501-72000/sp71528 .exe

  Bluetooth:

  This package contains the Broadcom bluetooth driver and software for the laptop models running a supported operating system. Broadcom Bluetooth 4.0 driver is required to activate the bluetooth 4.0 Broadcom devices and is compatible with Broadcom bluetooth 3.0 and earlier versions.

  File name: sp71440.exe

• Equium A110-252: how to enable the wireless function?

  Hi, first time ive been on this forum. I recently bought the toshiba satellite (think that's the spelling) and a wireless router. now, the router works well with my other computer, is very fast, but I can't go online with the laptop. all the info I get, is that the wireless is not activated? its got beat me, so I hope someone out there can help me to solve the problem, so I can start using my laptop in the room. Thanks in advance. Susi

  Hello Susi

  The first use of WLAN switch and move it to THE post. The WLAN control light should be on. After this check in If Device Manager card is correctly registered.

  The last step is to use the FN + F8 key combination to activate and enable the wireless network adapter. When activated the WLAN connection must be configured correctly. I assume that your camera comes with WLAN client utility. If you use this utility to configure the WIFI connection, please ensure that this WLAN Windows option is disabled.

• Satellite P750 - 02K - how to enable the wireless interface?

  Hello

  I just bought a new laptop Satellite P750 / 02K with Windows 7 64 bit. How can I enable the wireless interface?

  I tried the Fn + F8, but it says it all, this is the 'wireless communication is disabled. Please activate the wireless communication switch. There is no switch that I see. The device driver is enabled and active. I even tried to reinstall the driver. The user manual makes no reference to a process physical either pass. I checked the BIOS but see no setting for all the wireless settings. I tried to restart the flash without result map.

  Any suggestions? Thank you.

  Hey Buddy,

  I Don t Satellite P750 in front of me, but the wireless network card is in the Device Manager?

  On Satellite P750, there is a tactile button between the screen and the keyboard to turn the WLAN function. The second button on the left (symbol of the antenna), you need to press to activate the WLAN.

  Also, check the BIOS. As I know most notebook contains an option for the WLAN that must be set to active.

• How to hide my wireless connection personal House of the user of the computer on the outside

  I see from time to time by my window a vehicle that is parked outside using their computer. Someone told me that they can connect to the internet using my wireless signal. How can I hide the outside user I have a wireless connection?

  Hello Maria,.

  There are a few things you can do to make sure that you are safe.

  #1. Make sure that your wireless modem is protected using a personal code to access WEP or WPA2. This is done by going to the configuration of your modem and the establishment under the wireless tab / link / article. Of the modem user manual must be able to guide them in this process.

  #2. The other way is to disable the broadcasting network option in the modem. The only problem with this option, it is only people who are currently using the network can get on again.

  I recommend establishing a password on your wireless network and in this way people can see your broadcast network, but they will not be able to get on it, unless they have the password.

  Hope this helps,

  JB

• How to set the VPN connection in Windows 7 64 bit?

  Hello

  How can I set up a Vpn connection in Windows 7 x 64 bit.

  Thank you.

  Hello

  Go to the network control panel and Internet-network sharing Center.

  http://www.windows7hacker.com/index.php/2009/08/how-to-set-up-a-VPN-connection-in-Windows-7/

  Note that you need to know the login and the password to access the Internet :)

• How to start the VPN connection when windows is running

  Original title: trouble with automatically the VPN connection

  Hi, I want to have my VPN connection to start automatically when windows is running.

  Simple version:
  I tried various different methods, including; Paste the shortcut in the startup folder and adding the task in the Task Scheduler.

  I have the same problems with both methods. Just the VPN starts automatically... I have to run it manually whenever I turn on the computer or wake up sleep mode.
  Does anyone know other methods finally a solution for the other two methods?
  In the version of the depth of the problems:

  Method of Task Scheduler: I get argument is not valid, it is even after I have successfully created the task and click OK. The task will not work, and also by some strange reason, my VPN password is not get recorded on my connection more. So now, I need to manually start the connection and type in the password. (I click on save the password whenever this does not work, when the task is active...)

  Shortcut to the startup directory: Simple and easy... It simply doesn't get it. I followed the steps very carefully and I'm 100% sure that I did it the right way...

  These links have good information on how to open a VPN connection to the Windows dΘmarrage

  http://www.dariancabot.com/2010/11/15/automatically-connect-to-VPN-at-Windows-startup/

  http://www.Buchatech.com/2011/04/configure-Windows-to-automatically-connect-to-VPN/

• How to enable the DVD library in WIndows 7 Media Center

  How do you enable DVD library in Win 7 Media Center?  I tried editing the registry as in Vista, but it does not work with Win 7.  I am running Win 7 Pro 64-bit version.  Thank you

  Hi zt75,

  Run you manually editing the registry?

  Have you clicked on fix it from the link below? If this is not the case, click on fixit and check if that helps.

  How can I enable the DVD library in Windows Media Center on a Windows Vista-based computer?
  http://support.Microsoft.com/kb/930526

  (Although this article is for Windows Vista, we can always give it a shot in Windows 7.)

  Or do these steps and check.

  To enable the DVD library in Windows 7, follow these steps:

  1. If Windows Media Center is running, close it.
  2. click on start.
  3. in the search box, type regedit.
  4. in the list programs, click on regedit.
  If you are prompted for an administrator password or a confirmation, type your password, or click on continue.
  5. Locate and then click the following registry subkey:
  
  HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Media Center\Settings\Video settings

  6. in the Details pane, right-click VideoGalleryView, and then click on edit.
  7 remove the content that appear in the value data box.
  8. in the value data box, type Gallery, and then click OK. Registry value data: Gallery = Activate My DVD; Play = not to activate my DVD
  9. close the registry editor.

  To verify that the automatic fix worked, restart your computer. You should now see "DVD library" from the menu. To add DVDs, go to the menu information (click on 'i' on the remote control) and select "Add Movies.

  Try this also:

  1. If Windows Media Center is running, close it.
  2. click on start.
  3. in the search box, type regedit.
  4. in the list programs, click on regedit.
  If you are prompted for an administrator password or a confirmation, type your password, or click on continue.
  5. Locate and then click the following registry subkey:

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Start Menu
   
  Check if it has a value of HideDVD, and if the value data is set to 1. If the data in the value of HideDVD is set to 1, then you have two options. One option would be to delete the HideDVD value. The other option would be to change the value from 1 to 0 data.
  6. close the registry editor.

  EDITING REGISTRY WARNING:
  Important:   This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  How to back up and restore the registry in Windows: http://support.microsoft.com/kb/322756
  
  Additional information:

  http://blogs.technet.com/fixit4me/archive/2009/01/02/enable-Media-Center-DVD-library-fix-it-live.aspx

  Aziz nadeem - Microsoft Support

• Is there a way to authenticate a wireless connection in Windows 7 without defining the wireless to connect automatically and then restart?

  Windows 7 machines tell unauthenticated when connected wireless to our domain. The unauthenticated message disappears if we connect automatically to wireless connection and restart. Is there a way to authenticate without a connection to the wireless automatically and restart? For example, I would like to connect manually to the wireless, whenever I want and as soon as I do that authenticates.

  I use a router configured medialink wireless more as a wireless switch. DHCP comes from our server. Security is WPA-Personal. I also tried to use a different wireless router configuration with a radius with PEAP server and that does not work either. The server radius authenticated the user, but the message on the computer remained the same: "domain.local 2 unauthenticated.

  Each way in which users are able to access the resources, but this message is driving me crazy. We do not get this message on all XP machines.

  Client side, I tried to turn on the discovery of the network, joined the field, turn off any firewall (only using windows), updated drivers NETWORK card, update the firmware on the router, etc..

  Am I missing something?

  Thank you!

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.

  http://social.technet.Microsoft.com/forums/en-us/winserverfiles/threads