HP 15-g012dx: ram HP 15-g012dx problem

Similar Questions

• Mac Pro RAM, Audio, Bluetooth mouse problems

  I recently bought an Apple factory refurbished Mac Pro (end 2013) and replaced the three-chip RAM of 4 GB with 16 GB of Crucial two chips. Everything was great for the first two weeks. Then I started having a strange audio problem. Audio would become suddenly agitated. I disconnected and reconnected the speaker output and it would start working again. Finally, unplug the unit and plug the unit has stopped working (audio would eventually just stop working completely... zero sound with or without the speaker plugged in...) and I had to restart the computer.

  Then one day I noticed that only 16 GB of RAM showed up (I run own memory, so he's in my toolbar). I opened the machine and moved the two chips on the other side and when I rebooted, I got 32GB again.

  Then I noticed that when the audio problem came once again (he seems to be after the computer has been for a few hours or more) my Apple bluetooth mouse would disconnect and reconnect intermittently... ONLY when the audio starts to get restless again.

  I zapped the PRAM several times and now I get the 32 GB of RAM only after disconnecting the chips and MOVING them to another location, but not all the time. The audio port will begin to spoil, I reboot and I'm back to 16 GB.

  So, is it bad RAM? I removed a single chip and the audio problem still happens.

  Anyone have this problem? Apple Care suggested I bring it in the Apple Store, but I thought that I ask here before go this road, just in case there is a known issue.

  Thank you!!

  Rick...

  To establish if it is a RAM problem, remove 16Bb sticks and replace the original 4 GB sticks.

• Satellite M30X and Mat * a dvd - ram uj-8205 burning problems

  I have Satellite M30x and Mat * one year dvd - ram uj-8205. On the beginning everythinks worked very well, but in the last months of 2-3 that it cannot reads some CD and have problems with CD burning
  I restarted the laptop with the recovery cd, but still the same problems. Before robooting, I used nero 6, thougth perhaps, this is the problem in nero, now using just Sonic record now accompanies the DVD.

  Please anybode help me?

  Hello

  How to help you if you don't mention what CD cannot be burned (original music CD, homes burned CDs, just specific producers, only some files are not readable). Give us more info on this issue.

  Check a little better, and if there is no success is perhaps the defective drive. It is well known that some CD (a cheaper) cannot be burned properly.

• Replacement of my RAM will fix my problems?

  Ive had a laptop to play for about 5 years now. He was notorious for overheating and it happened a lot. After reviewing the problem for a few years with fans and coolers, I finally got a virus that put an end to him. I reinstalled Windows 7 (64 bit) on this subject, it worked for a little while, but had many problems. Finally, I had a boot error after it overheats once and I could not get past the blue screen with the error so I took it to a local computer maintenance shop to check how much it would cost me for repairs. The tech helped me to discover that one of my RAM slots has been damaged (either moisture or heat damage) he told me that I would be better to replace the whole motherboard and I couldn't afford it. But will start the computer and the work (with a lot of mistakes) as long as the damaged slot is not a stick of RAM in it. So Ive been running on 1 key 2 GB compared to the original 2 2 GB sticks since then with many more problems than before. As the programs getting errors and be forced to close, and I get an error fatal frequent blue screen. I finally have the money to buy a new key of 4 GB of RAM to upgrade instead of the 1 2 GB. Im hoping this will bring this back to the speed and fix problems. IM curious as to the time its worth buying or if my laptop is screwed for good? any comment is appreciated, thank you.

  Jclement

  These accidents were caused by the corruption of memory (probably a driver).  Run these two tests to check your memory and find which driver is causing the problem.
  
  * Don't forget to download any other DMP files (especially those running auditor)

  * If you are overclocking reset all default before running these tests.
  In other words STOP!   If you don't know what it means that you're probably not
  
  
  1 - Memtest.

  * Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. http://www.memtest.org

  * Boot from the CD and let it run at least 5 or 6 passes.

  * Don't forget, anytime Memtest reports errors, it can be bad RAM or a bad motherboard slot.

  * Test the sticks individually and if you find a good, test it in all slots.

  Any error is indicative of a memory problem.

  If a well-known stick fails in a slot of motherboard, it's probably the slot.

  2. Driver Verifier

  Using Driver Verifier is a dubious proposition. Most of the time it will crash and it will tell you what is the driver.

  * But sometimes it will crash and will not tell you the driver.

  * At other times it will crash until you can connect to Windows. If you can't mode without failure, then you will have to resort to editing the registry offline to disable driver verifier.

  * I would suggest that you first back up your data and make sure that you have access to another computer so you can contact us in case of problems.

  * Then do a system restore point (so you can restore the system using the functionality of Vista/Win7 Startup Repair).

  * Under Windows 7, you can do a startup repair disk by clicking Start... All programs... Maintenance... Create a system - with Windows Vista repair disc, you need to use your drive installation or from the "Repair your computer" option at the top of the Safe Mode menu.

  So, here is the procedure:
  -Go to start and type "auditor" (without the quotes) and press enter
  -Select 'Create a custom settings (for code developers)' and click 'Next '.
  -Select "Select individual settings from the list complete" and click "Next".
  -Select the entire document except for "Low resource Simulation" and click "next".
  -Select "Select driver names from a list", then click "next".
  * Select all drivers that are NOT supplied by Microsoft and click on "Next".
  -On the next page, select "Finish".

  * Restart the system and wait as he crashed to blue screen.

  * Continue to use your system normally and if you know what are the causes of the crash, do it several times. The objective here is to get the system crash because Driver Verifier is stressing out the drivers. If it is not planted for you, then let it run for at least 36 hours of continuous operation.

  * If you are unable to Windows because it crashes too early, try safe mode.
  * If you can't mode without fail, try to use the system from the installation DVD restore to bring the system back to the previous point of restoration that you created.

  * Further reading
  'http://support.microsoft.com/kb/244617 '.

  Using Driver Verifier to identify issues with Windows drivers for users advanced

• After Effects keeps crashing during the RAM Preview? [Sound problem]

  Hey, personal Adobe! Adobe After Effects worked well during the first week! But about 3 days ago I discovered a major problem. Whenever I have add all the sound/music files in the application and click the RAM Preview, Adobe After Effect crashes. It was surprising to me because it never happened to me before. But here's the thing, if I don't add any audio files in my project and click RAM Preview, it does not crash. Any ideas on how to solve this problem?

  Thanks again!

  You should consider updating your OS and your AE.

  Apple fixed some critical bugs in that related to EI 10.10.5, so I'll try that first.

  So, if you don't mind the new cool blue colors, you should also consider updating AE - at least to the last version of CC 2014. There was a lot of bug fixes and new features added.

• RAM with Satellite P300 problem

  Hello

  My P300 has 4 GB of RAM, integrated, but Vista says he uses only 3065MB, although the information shows 4GB system memory available.
  No idea why?

  Your satellite P300 Vista SP1?

• Pavilion 15-p011tx: DDR3 + RAM causing DDR3L of problems of 840 m NVIDIA?

  This 15-p011tx Pavilion has been upgraded with regular 1.5V DDR3 SoDIMM. I have problems with Optimus graphics (GeForce 840 peripheral m in the process of disappearance - EJECTED?!).

  I was just wondering if the inclusion of the SoDIMM 1.5V may be somehow responsible.

  Any ideas/suggestions?

  Never mind. I've just updated BIOS UEFI F.03 F.07a (later), and everything is fixed.

  Don't even try to understand what in the BIOS was causing GeForce 840 m to disappear, but now it is totally fixed and run like a dream!

• Sony Vaio matshita dvd - ram uj870qj ata device problem worked perfectly, but now is recognized in devices such as the CD-ROM Manager

  Hi this device worked perfectly, but is recognized as CD-ROM Device Manager, so does not recognize blank disc. Of course it reads again properly. I tried all the advice on many sites without success, can anyone help? This is not the first time that this happens, the last time just, he began to work again, seemingly of it of own accord.

  Grateful for any advice. Pete

  Your CD or DVD drive cannot read or write media - Fix It:
  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  Your CD or DVD drive is missing or is not recognized by Windows or other programs:

  http://support.Microsoft.com/kb/982116

• RAM problem

  I have 8 GB of RAM installed in my MacBook Pro. Suddenly, I found almost all of this is in use, making my computer run like molasses in winter. I recently installed a updat for OSX but don't know if that is the question. I run many apps and just do basic stuff, nothing complicated. And it is not consistent, either.

  All used RAM isn't the problem. That's the idea and the OSX is very good in management RAM.

  After a report of etrecheck for an analysis of your system.  http://etrecheck.com

• Satellite Pro 4340 - RAM upgrade problem

  I have exactly the same problem as Juan29. Link to his post below.
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=15837&MessageID=57907

  I want to improve my Toshiba Satellite pro 4340 to 320 MB of ram.
  The computer came with 64 internal RAM and I bought 2 x 128 MB of ram.

  My problem is that the second (B) ram slot does not detect the new ram.
  2 x 128 MB of ram were tested both in the ram slot (A) and work.
  I thought that a bios upgrade would solve the problem, but it didn't.

  I have the same defective (B) housing like Juan or does it have
  a solution?

  Help, please.
  Best regards
  Martin

  What memory did you use?
  I've found that these modules are compatible:
  PA3003U - 1 M 03 32MB MEMORY KIT
  PA3004U - 1 M 06 64 MB MEMORY KIT
  PA3005U - 1 M 12 128 MB KIT MEMORY

  I think there could be a problem of compatibility of the module.
  I put t see any other reason the problem

• Windows 7 HP x 64-problem of RAM weird

  Well I hope will happen to solve this one... someday.

  Here I am with a weird RAM problem. Quite simply, this device of i3 AIO has a pair of 8 GB... 2 x 4 GB, but only a crack can work. The second I install the second 4 GB of ram, the computer begins to act strangely and unbootable... Either just with an operating system does not work in the end.  Remove the second RAM solves the problem pretty much right away to restart the system.  I have fought this one for some time without success... Thinking the RAM was a problem had a pair of new ram... Same problems... I've tried different machines slot... The same problem. For the second he sees 8GB (2 x 4 GB), it blends.

  Reboot several times with the 8 GB and making a COTM reset sky got me to a point that the installation of the computer became corrupt... (Even removing a 4 GB)

  Re all installed. As good as new. Fees. 4 GB to work totally fine and stable on two slots... but the second I add another strip of RAM... Problem is back

  Help. Help. Help...

  This was implemented for some time

  Now totally fall for launch at the start of all the...

  Removed the second 4 GB

  Now everything is good... After some weird restarts, the Startup Repair and CHKDSK

• SpeedGrade CC 2014.2 build 8.2x51 reading smoothing / jerky 4K with GPU R9 295 x 2 - it uses only 2 GB of RAM (8.1 Windows 64-bit), Mac OS - same problem

  Hello, guys

  I have following configuration:

  I7-5960 x 4.3 GHz

  32 GB DDR4 RAM

  ATI 295 x 2 8 GB (Gpusniffer.exe watch 3072 MB on each unit of Hawaii)

  Samsung XP941 Ultra M.2 (> 1000 Mb/s)

  Some 850 Pro SSD for H.264 4 k source

  Latest version of Speedgrade CC 16/02/2015 (DUAL MONITOR SETUP - 2560 x 1440 for Interface and 4096 x 2160 for previewing)

  I work with a lot of short 10-15 seconds 4 K 4096 x 2160 24 fps H.264 clips of Panasonic GH4. Import their first CC as some stabilization warp, cut them, save the project and opened in Speedgrade CC all are fantastic smooth in first CC.

  Speedgrade - a simple color - exhibition, some keyframes and simple scoring correction for certain substances. I use the GPU acceleration for sure have lots of 4096 x 2160 4K 24 fps. But it is not flexible and smooth after that a correction is applied. Everything is jerky and freezes the first seconds, when I press 'PLAY'. I used resources, the Manager monitor tasks (Winodws 8.1 64-bit) and Afterburner. And there's what I discovered:

  • Afterburner shows the use of mono-GPU (as we know it for playback only 1 GPU used) the same amount as in first. SpeedGrade CC use 2, 5 GB of VRAM. Also, if I use one zero effect - accelerating gpu, like "transform", for example, imported first, I get "not enough GPU resources" message in Speedgrade. Afterburner shows, CC Speedgrade tried to use more, and then Max 3GB available VRAM during that time. So I turn off these effects, before you open a project in Speedgrade.
  • CPU is low (15%) use, perhaps a little lower, then in the first CC
  • Disc - 3-10%, H.264 is weak on this subject
  • RAM! -is the problem. I have been authorized to use the 29 GB of RAM for Adobe apps. Speedgrade CC use no more then 2-3 GB according to the the Task Manager (for most 2 GB) and 8.1 Windows resource monitor 64-bit Pro. After I finished with the color correction, a project open in first DC, work with lumteri on smooth and! First CC use 9 to 10 GB of RAM to play the same music video in full resolution smoothly!

  
  

  I already reinstalled everything, including drivers for the GPU, 8.1 for Windows and Adobe CC even result.

  MacBook Pro 15 retina end 2013 with i7-4960HQ/16 GB of RAM/Geforce 750 m UPDATE!

  Under Mac Os Yosemite 10.10.2 - same situation here. First CC use 5 GB (of 11 GB of available) 4096 x 2160 Prores 422 HQ and is usable, smooth with a few drops of frame.

  SpeedGrade CC uses 2.5 GB RAM of 4096 x 2160 and it is impossible to use plenty of 4096 x 2160. Only 1/2 resolution of overview is smooth and usable on the screen of the laptop. 4096 x 2160 externally connected through Thunderbolt monitor, it's a lot rougher, I think it's hard for 750 m with 2 GB of VRAM.

  UPDATE! Previous version (CC 2014) of first CC and CC Speedgrade Windows 8.1 64-bit - even situation.

  
  

  What do you think?

  
  

  My opinion - Speedgrade CC is not optimized for 4K resolution. First CC is good for 4K.

  BTW, for more information, latest AMD catalyst driver 14.12 omega has a problem with my R9 295 x 2 and engine reading Mercury (MPE) OpenCL - just black with sound screen, when I turn on the GPU acceleration. So I use the previous version of 14.9. With 14.12 GPUsniffer.exe found a device with 4 GB of VRAM GPU and a GPU with 3 GB of VRAM (normally obligatorily 3 + 3 GB 295 x 2 Dual GPU radeon chip).

  Yes

  So, finally, Speedgrade CC works 95% smooth time with 4096 * 2160 H.264. But it was necessary to turn off all effects in first Pro CC. Nothing new. I found a few discussions on this fact, but after that I spent some time with experiences.

  Stabilizer Warp even alone is enough to make Speedgrade CC really agitated. 'Transform' effect simply blocks Speedgrade CC with "GPU resources.

  Each effect uses some VRAM (for Warp stabilizer 200-300 MB). After you have disabled all effects had load VRAM under/near 2 GB for the little clip 4096 * 2160.

  First CC flies simply with unique x 290 or 295 x 2 (which is the only x 290 during playback). Even 3GB VRAM available software Adobe CC.

  PS Macbook Pro retina 15 "with Geforce 750 M 2 GB VRAM would work smoothly with Prores to half a preview/playback resolution - 2048 * 1080. CC CC SpeedGrade or Premiere Pro with 1/2.

• Genius Bar broke my RAM Slot

  My computer knew some problems turning on and I took it to the genius bar. They went through my MacBook as there are of course many causes possible so I went to pick up another day, when they were performed. I have just return and everything works well except the RAM. I had 8 GB installed and registered only 4 GB. After rotation autour and only use a stick at a time I have diagnosed the issue as the least RAM slot is the problem. I want to know what I have to do? Is it a simple fix I can do (or try) or I need to resume and explain?

  I expect that you will need to make an appointment with the Genius Bar, because apparently you have diagnosed the cause:

  'Genius Bar broken my RAM Slot'

• More RAM will increase the speed?

  Our iMac with an Intel Core 2 Duo 3.06 Ghz and 4 GB of RAM, running OS 10.10.5 slowed way. If both users are online, the second user account takes forever to initialize.

  We have two empty RAM slots and wonder if the additional RAM would ease the problem. Or do we need a newer, faster processor, which I assume means a new computer.

  Paul B.

  Hi Paul, more than RAM we're crazy. But I don't think it's the whole issue. Download and run EtreCheck, created by one of his own assistants here in CSA. It is a diagnostic tool that is very useful for us to find problems. It will also give us additional specifications on your Mac. After his execution after the logfile here. It will never contain any personal information.

• How to replace RAM on Satellite 2450?

  I own a Satellite 2450-201 and want to upgrade the Ram. The only problem is to know how to access.

  Anyone know?

  Hello

  You won't find the memory locations at the bottom of the unit. As far as I know there are only places to drive HARD, battery and slim select bay.
  However, this computer has 2 sticks of memory under the keyboard.

  Please follow these steps:
  1. turn off the power to the computer
  2. remove the power adapter
  3. remove the battery
  4. open the screen and remove the small cover at the top of the keyboard
  5. you will find 3 screws. Remove it
  6. carefully remove the keyboard (please don t forget the flat cable)
  7. raise the insulating sheet covering the module memory to appear the module.

  Well, it's not very difficult to upgrde the memory and the entire statement, you will find in the user manual that must be installed on your laptop. Chapter 8