HP C4580 cannot print - connected usb or wireless

Similar Questions

• Why doesn't my computer series sony vaio y cannot detect / connects to a wireless connection

  Why doesn't my computer series sony vaio y cannot detect / connects to a wireless connection. only through connection cable/usb... Please help me... Thank you...

  Hi JaqD,
  to go with that said Brian, more in detail the best options, we can give you.
  In the meantime, here are some generic troubleshooting steps:
  http://support.Microsoft.com/kb/313242

• HP Photosmart C4580 cannot find network Verizon FIOS wireless

  I already had my C4580 connected to my wireless network and then I moved and now I have Verizon FIOS and can not get the printer connected wireless!  It connects via USB, no problem.

  Any help is appreciated, I spent 6-8 hours trying to solve the problems without result... :-(

  Facts to consider:

  Router:

  Verizon FIOS network

  MI424WR router model

  WPA

  No Mac filtering

  Printer:

  Wireless Network Test report

  Wireless On = PASS

  Work wireless = PASS

  Found the network (SSID) name = FAIL

  Security = PASS

  Networks detected wireless = 4

  Computer:

  ThinkPad x 201

  Windows 7 64 bit

  I tried to download and install the HP printing software that I found when searching support and each time it fails with a fatal error, uninstall the software and restart my laptop.  I turned off as much security as I can and retried (6-8 x) same error every time.

  I think I need to run a wireless network on the printer config, but may not know how to do that when I can't download the software?

  Please help, I am running out of patience.  I realize, it could be the router config, but I thought I would start here.

  Thank you

  I was able to solve the problem using my wife's computer to run the HP software, change the network settings on the printer.

  The main problem was that I couldn't install the software on my cell phone company (Cisco) to correctly configure the printer.  They must have controls in place that software HP must and cannot get the installation.

• Problems when printing with USB or wireless - offline message

  Hello world

  I use a HP ENVY 4500 with a laptop Acer Aspire laptop and a desktop computer HP Pavilion 500, both with an Intel i7 and Windows 8.1. Initially, I configured the printer to work with both PCs wireless. The wireless network is provided by the modem of my provider (Telenet), so it is not very strong I increased it with Devolo powerline adapters. Print is fine, only when I want to print more pages then 3 print job is stopped in the middle of page 4. I get a message that the printer could not print the document, and the page comes out half print. I connected my printer with a USB cable and configured to work with USB, but also wireless. But that Don t always works, today, I tried to print a document from Mozilla Firefox and it would not start. The printer can be used on both sides without choosing the connection?  Also I get the message that the printer is offline and cannot print the document, even if it's actually printing.

  When I open the doctor print & scanning everything seems to be ok wth the printer, no defects are detected. Wrong me?

  Hello @DenOuwe and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you run into connectivity errors.  I would like to help.

  I would recommend using this thread on missing/partial prints & printer offline on Windows 8/8.1. by @JERENDS

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• HP 6830 can be configured to print with USB and wireless?

  a provide you with similar instructions to put in place the USB and use wireless to my hp 6830 on an iMAC running on OS X Yosemite 10.10.5?

  Hey @kj6311,

  Welcome to the Forums of HP Support!

  I see that you want to install your HP Officejet Pro 6830 e-all-in-one printer via a USB cable connection and the connection Wireless on your computer Mac OS X 10.10. I want to help you with this today. Can I please you follow the steps below.

  Step 1: Set up the device:

  To begin, we will set up and install the version without wire of your printer.

  1. On the front panel of your printer, swipe, and then select Network Configuration
  2. Select the wireless settings
  3. Make sure that Wireless is enabled
  4. Then choose Wireless Setup Wizard
  5. Select your network name (SSID)
  6. Enter your wireless password. Is case-sensitive.
  7. Once the wireless connection has been configured on your printer successfully, proceed to the next step.

  Step 2: Install the wireless device:

  1. Please click here to download the latest driver for Mac OS X 10.10 for your printer
  2. Run the network installation
  3. Once the wireless installation completed successfully please try wireless printing to confirm that your printer works via the wireless connection. Once tested, please proceed to the next step.

  Step 3: Install the USB device:

  Please connect the USB cable from your printer to the computer.

  1. click on the menu of Apple , then Preferences System.

  2. click on Print & Scan and then check if the name of your printer appears in the printer list.

  3. click on the plus sign (), click Add a printer or a Scanner, click the name of your printer.

  4. click on the area of use or with the help of Print and then select the name of your printer on the shortcut menu. Ensure that the Officejet driver is selected.

  

  5. in the 'name' section, add USB until the end of your name of the printer so that you can make the difference between the two Officejets.

  6. click Add to add the printer to the list.

  Now you should have two copies of your printer showing under Print & Scan. Please let me know if the steps to solve your problem. Good luck!

• Cannot print/connection of Windows 7 for shared PSC 1315 on the XP Machine

  I have a HP PSC 1315, connected to a computer running Windows XP (32 bit).  This printer is shared.  I can access it from other XP machines on my home network.  I can't access it from my computer Windows 7 (64-bit).  I can see the printer is shared on the computer, but when I double click on it, I get the following error:

  "Windows can't find a driver for hp PSC 1310 series on the network."  To locate one manually, click on OK.  Otherwise, click Cancel and consult your network administrator or the printer manufacturer's Web site. »

  Then I tried to download the driver Windows 7 (64 bit) of HP and installed on my Windows 7 machine:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-75052-1&LC=en&DLC=en&cc=CA&...

  At the end of the installation, it asks to connect the printer to the computer via USB.  Because I'm not physically the printer connected to the Windows 7 computer, I check the box that says I can't login now and go forward at the end.

  Then I tried to connect to the printer and I get the same error.  I try to locate a driver manually.  I point to c:\windows\inf\ without success (I am * if * the driver info might settle there, but I don't know what the name of .inf).  Windows says that it cannot find an appropriate driver.  Maybe I should be looking elsewhere?

  I found some troubleshooters on the HP website, but it does not give "shared printer on a network" as one of the schemes to solve connection problems.

  I'm a little confused on this one.  Hoping that there will be something simple, I missed.

  Thank you!

  Hello

  Kahless wrote:

  I have a HP PSC 1315, connected to a computer running Windows XP (32 bit).  This printer is shared.  I can access it from other XP machines on my home network.  I can't access it from my computer Windows 7 (64-bit).  I can see the printer is shared on the computer, but when I double click on it, I get the following error:

  "Windows can't find a driver for hp PSC 1310 series on the network."  To locate one manually, click on OK.  Otherwise, click Cancel and consult your network administrator or the printer manufacturer's Web site. »

  Then I tried to download the driver Windows 7 (64 bit) of HP and installed on my Windows 7 machine:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=Al-75052-1&LC=en&DLC=en&cc=CA&OS=4063&product=374568&sw_lang=

  At the end of the installation, it asks to connect the printer to the computer via USB.  Because I'm not physically the printer connected to the Windows 7 computer, I check the box that says I can't login now and go forward at the end.

  Then I tried to connect to the printer and I get the same error.  I try to locate a driver manually.  I point to c:\windows\inf\ without success (I am * if * the driver info might settle there, but I don't know what the name of .inf).  Windows says that it cannot find an appropriate driver.  Maybe I should be looking elsewhere?

  I found some troubleshooters on the HP website, but it does not give "shared printer on a network" as one of the schemes to solve connection problems.

  I'm a little confused on this one.  Hoping that there will be something simple, I missed.

  Thank you!

  Here's a good explanation of how to share a printer from an XP PC to Windows 7 PC on a network home.  It should work since Windows 7 (64-bit) PC can see the partition Windows XP 32-bit.  What you missed was the type of port to use for the network connection.

  Best regards
  ERICO

• HPC8180 printer connects to the wireless network, after upgrade firmware to the router wireless

  My HPC8180 has been wireless since I bought it some time ago.  I recently had to upgrade the firmware on my router wireless of Netcom NB9W and since then my HP will not solve for the wireless network.

  I run the wizzard of wireless network on the printer, select the correct SSID and enter the WEP key according to the instructions.

  It will then not connect.

  Print the summary I have says that it passes all except:

  No filtering = Fail

  Connected = do not run

  Signal strength = very weak (which is strange because it is about 10 feet away from wireless router).

  Other networks detected matching your network name (SSID) = No.

  Summary says:

  Network Name (SSID) altnet (correct)

  Address IP = not applicable

  Configuration source = not applicable

  Communication mode = Infrastructure

  Authentication type = open system

  = 64-bit WEP encryption

  I have NOT activated the mac address filtering

  Any ideas?

  Your router appears to be a DSL modem-router.  Those who can be difficult to connect to.  In addition, WEP can be problematic and is no longer a measure of security.  WEP can be broken in 10 minutes approximately with the freeware on the internet.

  We will do three things:

  1. replace the WPA or WPA2 encryption.  You can make your own password.  Do 13 or more characters, numbers and uppercase and lowercase letters.

  2 reset the default settings on your printer network (configuration > network area).

  3. attach to the router in this way:

  Sometimes the DSL providers have more control over the router like the printer.

  -Unplug the phone line from the router
  -Cut the power to the router, wait 30 seconds, then turn on the power.
  -Go through the normal process of the printer connected to the device (wireless configuration wizard)
  -Now to find the IP address of the printer (it should be on the self-test printout), type it in a browser.
  -On this screen, you will find a tab management network, then on the left wireless, then the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address).
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the white gateway and DNS
  -Finally, connect the telephone line, restart the router and the test.

• SE message: printer not detected, the printer connected to the wireless modem and I can't print

  Original title: printer connected to the WiFi modem and pc but get message saying unable to print printer not detecded

  printer not detected on pc but it is installed and signel wirless right message bed printer not detected

  Hi howard douglas.

  1. were you able to print before without any problem?

  2. when the problem started?

  You can try to connect the printer directly to the computer and check what is happening.

  Check out the link:

  Find and install printer drivers

  http://Windows.Microsoft.com/en-us/Windows-Vista/find-and-install-printer-drivers

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP6110 printer connection to the wireless router, USB port

  I have a HP Officejet 6110 all-in-one printer, a Toshiba laptop running Windows 7 and a CGN3ROG Hitron of wireless router.

  I try to get the printer on my home network by plugging it into the USB port on the router. I can't make it work. Has anyone managed to do this?

  Derek

  Hello Cheetah12,

  Thank you for your response. Yes, my printer - HP6110. I have read the manual you sent me and understand that I can not connect directly to the router with print server - print server HP JetDirect 175 x Rogers, tells me that the router is turned on print server. I'll have to break down and buy a wireless printer. The networks of the great printer if I connected to a computer.

• HP 6500 E709n cannot print from Windows 7 wireless

  I have 3 computers on my office network at home and a HP 6500 E709n with a wireless connection to the router. The printer does everything it's supposed to the XP machine. On the 2 computers running Windows 7, the printer will scan and fax but not print.

  When I used the USB cable to connect the printer to a Windows 7 computer, the functions worked well. So, apparently, is not just a matter of having the right driver (and I now reinstalled Windows 7 driver twice after my hard disk cleanup at best). I've checked absolutely everything, and all the recognitions seems to work going both ways. But whenever I try to send a document to the printer to Windows 7, it just sits in the queue.

  Other users have this problem? Is that what someone has solved? Thank you.

  Run this utility from the Win7 machines: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&jumpid=ex_r4155/en/hho/ipg/forum/network_diag/

• HP envy 4520: cannot print without directly using wireless

  I want to hp 4520. I want to print without using the direct wireless to my laptop. I always disconnect my home wifi network and use network want to live to be able to print wireless. Is it possible to print from my laptop using my local network, or I have to use the direct wireless to be able to print.

  Hello
  
  Try to remove the printer and then add it again by opening the Preferences tab and then selecting «printers & scanners»
  
  From there, click on the sign less under the printer icon to remove the printer and then add again using the sign.
  
  This may help to solve your problem of connectivity.

  

• Printer connected to 2 wireless networks?

  A printer wireless HP 6500 E710n-z can be configured to use more than one Wi - Fi?  We have a main internet connection, but sometimes we need to use an access point to the top.  The printer seems to be associated with a wireless network, and we are unable to print if you use the HotSpot.   I'm trying to do something of that printer is not capable?

  Answer is simple, the more than 6500 printer can do that.  The data sheet contains a wireless network.

  http://www.HP.com/hpinfo/newsroom/press_kits/2010/InnovationSummit/6500A_Plus_eAIO.PDF

  A more complex answer is that wireless modules and printer drivers were made to support wireless at the same time.  Most wireless, until recently, were made in support of a Wi - Fi connection at a time.  This is the case for most laptops and desktop computers as well.  HP has wireless in some of its printers who may have a client and a server (behaves an access point) at the same time.  I don't see this feature on the 6500 has more.

  Another comment - the printer doesn't have a function autoswitch like most of phones and computers.  He remembers only the current wireless network to which it is connected.

• HP Photosmart C4580 - cannot print two-sided, w / color, & don't scan on my Mac.

  Hello! I have a HP Photosmart C4580 and just got a Mac. Number of issues,

  (1) after that I finally found the duplex printing option for my powerpoint documents it wouldn't let me not and was gray/gray. I had to change the printer driver to something else to chance, and click on allow "duplex" (tried to do some research). Then when it let me print duplex he'd let me not print in color!

  (2) when I go to HP Scan Pro to try to scan something it says "error, sorry, scanner could not be initialized. Scanner not found. "My printer is on and can print documents, and my software is up to date. So a little confused.

  Any help is greatly appreciated, thank you

  Hello

  Please specify which version of Mac OS you have.

  to locate the inform, the Apple icon and click on about this Mac - OS version is displayed on this screen.

  How to set your printer?

  Using the CD, download it from the Web or simply connect to your mac and adding the pritner?

  As C4580 model State enterprises does not have automatic duplex unit unit 2 faces, the duplex option should be faded out.

  In order to manually, double-sided printing, open the print dialog box and click the 3rd selection box (Copies & Pages)

  Now select Paper Handaling

  Set the page to print in the form strange only and do printing.

  Now place the printed pages facing up and perform additional characters, while fixing pages to print mode only

  Now select paper Type/quality (the same menu to select paper handaling)

  Devote the Color Options by clicking on the arrow to the left to her.

  Make sure that it is set as ColorSmart/sRGB.

  On the issue of the analysis, please let me know the version of Mac OS that the HP Scan Pro is designed for older versions of Mac OS, while that for Mac OS 10.6 and above all the appropriate software contains the HP scanning software

• can not print says printer connected to the wireless network but pc says printer is offline

  happened before the printer says connected to the network but pc says offline

  Ok

  Have you tried the Network Diagnostics to see you the network can see the printer

  Go to www.hp.com/go/tools

  Network Diagnostics has a link to the wireless printing site that can help out you.

• Printing via USB and wireless error

  Hi my printer is a HP deskjet 3050 a printer all-in-one.

  He stopped to communicate with the computers in the House when we had questions related to internet. LLA modem has been reset.

  I uninstalled it and reinstalled the printer drivers and I can send the documents to the correct printer from the desktop and the laptop, and then I get a print error message. When I click to see what's printing, the document is listed in the queue, but it shows a document with three circles on it rather than on a Word Document.

  What happens on both computers and connected printing and wireless.

  Any suggestions?

  Thank you

  Hey @soleruler,

  If the printer only displays in the list programs and features on your Windows 8.1 systems indicates that generally your Deskjet 3050 has e-all-in-one printer was probably not installed correctly in the first place. You can certainly use the option "Remove hardware" under "Devices and printers" on these 3 computers to remove old copies of the printer. Just make sure that when you go to remove the unit there is no print jobs stuck in the queue. Print jobs stuck in the queue will cause the printer go into a status of "withdrawal" but the Deskjet printer will not erase until jobs are deleted. To check the queue just right click on the printer under devices and printers, and left click on 'see what's printing. If something is in the box, then just right-click on it and 'Cancel' jobs. Once cancelled, then you can proceed with the option "remove hardware".

  Let me know how these steps go for you. Good luck!