HP6110 printer connection to the wireless router, USB port

Similar Questions

• I received a message on my laptop computer that says not able to connect to the wireless router.

  I received a message on my laptop that says could not connect to the wireless router and it make reference to section of the knowledge base Microsoft 87112 for more information.

  I think you have transcribed the number incorrectly.  I think that the article you want is this one: http://support.microsoft.com/kb/871122

• HPC8180 printer connects to the wireless network, after upgrade firmware to the router wireless

  My HPC8180 has been wireless since I bought it some time ago.  I recently had to upgrade the firmware on my router wireless of Netcom NB9W and since then my HP will not solve for the wireless network.

  I run the wizzard of wireless network on the printer, select the correct SSID and enter the WEP key according to the instructions.

  It will then not connect.

  Print the summary I have says that it passes all except:

  No filtering = Fail

  Connected = do not run

  Signal strength = very weak (which is strange because it is about 10 feet away from wireless router).

  Other networks detected matching your network name (SSID) = No.

  Summary says:

  Network Name (SSID) altnet (correct)

  Address IP = not applicable

  Configuration source = not applicable

  Communication mode = Infrastructure

  Authentication type = open system

  = 64-bit WEP encryption

  I have NOT activated the mac address filtering

  Any ideas?

  Your router appears to be a DSL modem-router.  Those who can be difficult to connect to.  In addition, WEP can be problematic and is no longer a measure of security.  WEP can be broken in 10 minutes approximately with the freeware on the internet.

  We will do three things:

  1. replace the WPA or WPA2 encryption.  You can make your own password.  Do 13 or more characters, numbers and uppercase and lowercase letters.

  2 reset the default settings on your printer network (configuration > network area).

  3. attach to the router in this way:

  Sometimes the DSL providers have more control over the router like the printer.

  -Unplug the phone line from the router
  -Cut the power to the router, wait 30 seconds, then turn on the power.
  -Go through the normal process of the printer connected to the device (wireless configuration wizard)
  -Now to find the IP address of the printer (it should be on the self-test printout), type it in a browser.
  -On this screen, you will find a tab management network, then on the left wireless, then the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). If you know what it is, set an IP address outside this range but not exceeding 254 (the last number of the address).
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Let the white gateway and DNS
  -Finally, connect the telephone line, restart the router and the test.

• HP photosmart 5520 cannot connect to the wireless router

  The printer has worked I went on holiday, and now it will not work. I have run the wireless network test, and it says "hp printer is unable to connect to your wireless router.  The wireless router is connected and works fine.  My hp wireless computer (windows 7) works very well.

  The structural 'found ssid network name' report, said down

  But "current configuration" has shown the SSID

  can anyone offer a fix?

  Help

  colleenmercy

  Hi colleenmercy,

  In the network menu, select default network.  This reset the current network settings and will help you reconnect the printer to the network.  You can use the Wireless Setup Wizard or reinstall the HP software to reconnect.

• Laptop (windows 7) doesn't recognize computer (XP) desktop network, but connects to the wireless router

  I have two computers (desktop and laptop), a plug-and-play printer connected to the desktop computer and a wireless router.  My laptop was connected to the printer via a family group on the network connection.  I've recently upgraded the OS on my laptop from Vista to Windows 7 and now my phone does not even recognize the MSHOME network which was initially established.  I am able to connect to internet via wireless router (Verizon MIA 424 - WR... or something like that) but I can not connect to desktop files, devices on it and above all terribly printer.  What's weird, this is my office always recognizes my laptop and can even connect to my laptop from my desktop.  The network is established by the office which is running XP.  Not sure if this helps, but I remember when I set the laptop computer connection / original printer, I had to do a port mapping step funky.  Any help would be greatly appreciated!  FYI, I did everything suggested by microsoft windows help.

  NET

  Hello

  To access the XP of Windows 7 computer, you can:

  a. type the name of the XP computer in the Start > box Search in this format:

  \\computer

  b. press the Windows key + R and type the name of the XP computer in the same format.

  c. click Start > network , then click on the XP computer.

  For more information on the networking of computers running different versions of Windows, see this article:

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows

• Satellite A105 - unable to connect to the wireless router more

  I had the success of connection to a router Wireless Linksys for the last few months. Today, that I couldn't connect to the Linksys still another. A few times I have to connect to the Linksys router, but I got a weak signal so I would be disconnected. The green bars on the router Linksys under available networks are all solid green full bars, but I can't? t connect.

  To do or check to login once more?
  Thank you

  HM, you will need to do some research! What was the last you´ve installed applications? Installed new drivers/tools/software on your computer?
  If not you already installed the latest drivers for the chip wireless for your laptop? If not already done, then try it and Don t forget to update BIOS. :)

  If anything brought success then just to give a few comments. :)

  Welcome them

• no internet but not connected to the wireless router

  I have 400 SL with windows vista installed.
  Everything worked well for years, until a few days ago.
  It is the symptom, and what I've done:
  1. the laptop CAN connect to the wireless network, no problem, very strong, just signal has no internet.
  cannot ping google.ca.
  In network and sharing Center:
  Computer---> network---> Internet
  ^                   ^
  |                     |
  Red Cross OK
  2. all other devices (iphone, ipad, other laptops) can connect to the network and internet.
  3 did a system restore on the eve of this stoppped working. always the same.
  4A bought a wireless adapter, always the same. but it works fine on the other laptop
  5 tried to set a static IP, subnet mask, gateway, still the same problem.
  6. any other device can ping each other with the exception of this laptop...
  7. the seller cordless tool is uninstalled (Lenovo connection management tool)
  8 rebooted a million times between all the steps
  9 safe mode with network has the same problem.
  10 tried to use other wireless, still the same problem...
  need help...
  Thank you
  -Virginia

  Hi Virginia,

  Thanks for posting your query in the Microsoft Community Forums.

  After the description of the problem, I understand that you can not connect to a wireless network on windows vista computer.

  I appreciate your efforts on this issue, however no need for you to worry we are here to help and guide you in the right direction.

  Help me with the information below.

  -Don't you make changes on the computer before this problem?

  I suggest you to disable temporarily security software and then check if you are able to connect.

  Method 1

  You can also temporarily disable the security software and check if it works.

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  If disabling the security software solves the problem, then contact the manufacturer of the specific security software to fix the problem.

  Important: These steps may increase your security risk. These steps may also make the computer or the network more vulnerable to attack from malicious users or malicious software such as viruses. We recommend the process that this article describes to enable programs to operate as they are designed for, or to implement specific program features. Before you make these changes, we recommend that you evaluate the risks that are associated with implementing this process in your particular environment. If you decide to implement this process, take additional measures to protect the system. We recommend that you use this process only if you really need this process.

  Method 2

  Reset the router and see if that helps.

  Note: to help you reset the router, you can consult the manual that came with the router or the router contact manufacturer.

  You can see this help article.

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Hope this information is useful.

  Let us know if you encounter problems under windows in the future. We will be happy to help you.

• Laptop fails to automatically connect to the wireless router.

  Original title: re automatic updates for Windows Vista

  My wife & I have laptops running Windows Vista in our House. Recently, his cell phone fails to connect to our wireless router automatically. To connect, it must get the computer to automatically get new IP settings for the network adapter. However, she must do it several times to make a connection & must be done each time it connects. My laptop is not the problem. His only started to do recently. What can we do to make his newspaper from the laptop to the internet automatically without problems?

  Hello

  Follow the steps mentioned below and check to see if they help.

  Step 1:

  Card drivers update of your network.

  Step 2:

  In addition, you can uninstall and reinstall the Device Manager wireless network card to be a safer side.

  To uninstall the wireless device manager,

  a. Click Start, type device manager in the search box of start and press ENTER.

  b. Locate the network adapters and expand the same.

  c. Select the wireless connection, right click and choose uninstall.

  d. restart the computer, if prompted.

  Pilots should settle automatically after the computer restarts.

  Now you can install the latest wireless drivers and check if this solves the problem.

• Unable to connect to the wireless router

  I can't connect to my wireless router.  My PC shows that the router has an excellent signal strength. The password is correct, but it will not connect.  What Miss me.

  Moved from Explorwer Internet

  Original title: wireless network device network Ethernet network router

  Hi Trisha,

  Many routers need firmware updates to work with Windows 7. Maybe it's the issue.

  Please answer these questions:

  1. What is the brand and model of the router?
  2. If it works much earlier?
  3. Any changes made to the computer before the show?
  4. What is the exact error message received when you try to connect to the router?

  I suggest you try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:

  Set up a wireless router

  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  Setting up a wireless router
  http://resource.Dlink.com/connect/setting-up-wireless-router/

  Post back with the State of the question.

• I bought a Sony BDP - S185 connect Netflix Blu - ray player. I can't connect to the wireless router. Why?

  I just bought the blu - ray BDP S-185 drive so that I can access the internet (netflixetc.) on my new samsung tv. I tried to connect to my wireless router, but repeat me my connection type iswired and the connection has failed. Can I connect this player to a wireless router or should it be connected to the router? Difficult because the router is in the basement and the television on the third floor. Can I use the separator on phonejack (existing in the 3rd and.) and connect the two phone and blu ray player or do I need a netgear typedevice to connect this player? Thank you in anvance understand help. Sorry, it's so rambled butI am very confused here!

  Hi Robert,.

  Welcome to the community of Sony!

  This Blu - ray player is the BIV (Internet Video base) base model and does not support the wireless Internet connection. I suggest that you use the Ethernet LAN cable to connect the player to your router/modem.

  Thank you for your message.

• SE message: printer not detected, the printer connected to the wireless modem and I can't print

  Original title: printer connected to the WiFi modem and pc but get message saying unable to print printer not detecded

  printer not detected on pc but it is installed and signel wirless right message bed printer not detected

  Hi howard douglas.

  1. were you able to print before without any problem?

  2. when the problem started?

  You can try to connect the printer directly to the computer and check what is happening.

  Check out the link:

  Find and install printer drivers

  http://Windows.Microsoft.com/en-us/Windows-Vista/find-and-install-printer-drivers

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• When I try to connect to the wireless router, it asks you the password I put it and he then asked again and will not accept the password. all other computers (without windows 7) connect correctly.

  My new computer has windows 7 when I try to connect it to my router it ask the password, then he asks the network password I put in the same password and it does not accept it. I spent ove an hour on the phone with a very helpful and confused expert to the Virgin. He tells me that the password only I need to communicate with the router is the main. We tried a lot of things all very technical and finally he gave up. Other computers with vista on connect very well with no problems at all.

  The network is fine and all the settings are fine. Occasionally, it connects via a home network but then it stops. When I try to communicate with the printer wireless signal stops and starts.

  I don't hold much hope of a response that experts were left very confused by this first abandoned after 45 minutes and the second lastered over an hour are totally flumaxed and blame windows 7

  But everyone told me that windows 7 was supposed to be the best

  Your post has nothing to do with the Windows Update feature (compared to the upgrade of Windows). Please repost it here for assistance: http://social.answers.microsoft.com/Forums/en-US/w7network/threads ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Printer LaserJet 4100: Should which cable I for Laserjet 4100 connected to the laptop with USB port

  I have the HP Laserjet 4100 printer. I bought a new laptop with USB ports.  What type of printer cable I need to connect the printer to my laptop? Is there some kind of printer cable adapter, or something else that will do the trick?

  I have the same question about my HP Laserjet 1100 printer.

  Thanks in advance for your assistance expected.

  If I remember correctly, the 1100 uses a cable "C", alias MicroCentronics.  Have never seen an adapter for that one.  On the 4100, you can get a USB to parallel adapter.  They are pretty cheap and available at most CESS (Consumer Electronics Super Store) as Best Buy.  Staples and OfficeMax/Office Depot should also wear.  Online is cheaper if you have time to wait.

  The thing with these USB converters is often must 'install' the cable first.  In other words, connect it to the laptop, then wait so he could install, then connect the printer.  Depending on your operating system and if you have correct updates that can be almost instantaneous, and you may not even see it pop on the screen.

  Best idea is that since these are obviously not portable machines, connect them to your router via a network card.  I had the 1100 years and used a cheap 170 X.  I know most recent are available which are faster.

  For the 4100, see if you can retrieve a Jet Direct 620 unit on eBay.  Probably less than $50 and sometimes even as little as $25.  Stay away from the 600, 510 or 615 cards.  Low or as the 600, they can leave your network open to hackers.  No need to get Gigabit cards as they will be well above what the 4100 can handle.

  Now, two of these old devices, processing power and memory can be a problem.  Never try to print documents online.  Save them on your laptop, and then print.  You will probably get communication errors if you print directly from IE or FireFox.

  If the 1100 does not die, not even worth fixing.  Put into a Fuser is a nightmare.  The 4100 will probably work for another 20 years if you keep to clean and replace the rolls before they cause jams.

• B210A Photosmart - server connection error and does not connect to the wireless router

  I have problems setting up and to connect my router to my new printer b210A. Everything goes well with the initial configuration, and when asked to connect to the network at the start, it works. Then he said that the printer requires updates, downloads of updates, reboots, asks me if I want to activate eprint and as soon as I said 'Ok', I get a "the server connection error" and it is then no longer connected to the network. When I get out of the "server connection error" screen and attempt to reconnect to the network, he says 'Success', prints a Test report wireless, but never connects.

  It's the 2nd printer that I have had in a week, given that the person of HP online chatting told me my first printer had problems of "hardware", after experiencing the same problems and I'll be recommended. So - I did, and now I'm running into the same issues. The number of 800 was NO HELP - after recommended I have unplug and reconnect, then telling me there were server errors (when the printer was not connected to the network).

  We will set an IP address of the printer with a special focus on DNS domains:

  -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
  -Enter the IP address in a browser to reveal the internal settings of the printer.
  -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
  -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
  -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
  -Enter the IP of your router (on the Page of the Network Config) for the gateway

  -For the first DNS 8.8.8.8 and 8.8.4.4 for the second use.
  -Click 'apply '.

  Now, stop the router and printer, start the router, wait, and then start printing.

  After that, you will have to redo 'Add printer' using the new IP address.

• PSC C4780 - connects to the wireless router, then disconnects, repeat...

  So I have a C4780 who knows a problem similar to what other people know about with different models.

  It seems that the printer cannot be connected to the router for more than 30 seconds.  I look at the screen of the printer and the intensity of the signal will be full one minute and gone the next minute.  Although full shell, I am able to connect to the Web site of the printer from my computer and print from my computer.  Whenever the signal goes, is my ability to communicate with him.  I use a Linksys WRK54G wireless router.   Also connected to it are my HP Pavilion dv7-1132nr laptop and my laptop Dell Inspiron 1545.  None of them lose connectivity to the router or the internet during this time.

  When I installed the printer, he gave me three errors.  He told me to unblock the following ports from my PC to my printer:

  UDP 427 @ 192.168.1.102

  TCP 9220 @ 169.254.21.72

  UDP 161 @ 169.254.21.72

  I tried in my firewall opening completely disabling the firewall.  No approach has worked.  I do believe however, that the problem is between my PC and the printer, but rather the router and the printer.  The printer doesn't keep in touch with the router or the router is not that the printer is connected to it.

  It's late and I have worked on throughout the day, including an hour and forty minutes on the phone with technical support.  If anyone can think of any I've left out (I know there are a lot), I will be happy to provide it.

  Thank you

  Kevin

  I've seen similar problems.  I have not found this problem completely, yet do not give you the "shotgun" perscription, but it is better than losing the use of the printer.

  The 169.254.x.y address is problematic for the driver software.  The following three things helped a lot other people.

  (1) give the printer a address static IP - one that sits on the right subnet (192.168.1.x)

  * You must enter your router AND the printer's IP address, if the router gives to someone else, and so the printer knows what it is.

  * I do not have the printer in front of me, model if you cannot figure it out, let me know and I'll find the instructions.  If you can not understand how to configure your router, I'll try to find a reference in the manual.

  (2) make sure that your computers have only a connection to your router.  If you're wired AND wireless to your router, it can be confusing network of driver code.

  3) go to your firewall and unlock things like Setup has loaded, but replace all references 169.254.x.y 192.168.1.102 (assuming that you give the printer the number 102 to step #1 above)

  That said, you may be right in your assertion that the problem is between the printer and the router.  Your description of the signal strength indicator is strange.  To what extent is your printer from the router?  How is that distance compares to other devices on your network?  There the walls or shelves between the router and the printer?