HP designjet 500 plus network problem

Similar Questions

• HP Designjet 500 42: Old problem of driver update

  Hello

  I have HP Designjet 500 printer 42 in. And I can't update the old drivers. I downloaded new drivers drivers

  Installed new drivers and the printer connected to the computer. Installed printer itself. Driver version but check it shows in 6.08 (preferably printer-> subject) window.

  I deleted all drivers using pnputil.exe d Oem # .inf and printui/s/T2 orders. All the drivers of HP has been removed from

  C:\Windows\System32\DriverStore\FileRepository

  and

  C:\Windows\System32\spool\drivers\x64\3

  Installed new drivers (8.10) and pluged in the printer. Printer has been installed but with drivers 6.08. So I went to the "print management" as an administrator. Pressed on HP Designjet 500 42 by HP printer 'Manage sharing'-> "Advansed"-> "New driver"-> 'Disc' and in C:\Windows\System32\DriverStore\FileRepository I chose "dsgj510.inf_amd64_* *" folder and the dsgj510.inf file here. But could not find "HP Designjet 500 printer 42 in.". Here only:

  HP Designjet 500 42 + HPGL2 card; HP Designjet 500 plus 42; HP Designjet 500ps plus 42; HP Designjet 500PS42 + HPGL2 card; HP Designjet 510 42 inch printer and HP Designjet 510ps 42-inch printer.

  I tried to use HP Designjet 500 42 + HPGL2 card HP Designjet 500 plus 42 drivers. But printer would give an error message and do not print.

  With the help of the 6.08 driver version I can print from some software, but I need to print from AutoCAD. And AutoCAD gives me the error message "no: cannot use this configuration of tracer for one of the following reasons: the driver is not found, cannot find the device or the driver has a problem." No device has been substituted. "And I can't choose the HP designjet 500 printer in AutoCAD.

  It is a shared printer and other computers on the network have 8.10 drivers and can print from AutoCAD. Single computer, the printer is pluged cannot print because it driver 6.08.

  I found the problem.

  On the page under 10 64-bit windows this is only "HP Designjet 500 and 510 HP-GL/2 and HP RTL driver 64 bit" 8.10 drivers. And this driver is not HP Designjet 500 printer 42-inch drivers. But under 64-bit windows 8, here's two pilots. "Driver HP DesignJet 500 PCL3GUI 64-bit" 8.10 drivers and same as above. This file have drivers for HP Designjet 500 printer 42 inches and runs under windows 10.

  If HP support lazy to put all work them drivers under windows 10 for HP Designjet 500 printer.

• DesignJet Scanner 4520: Designjet 4520 Scanner network problems

  I have a Scanner of DesignJet 4520, that very recently stopped working on the network.  Wiring to the scanner is good and the network itself works normally.  I can't get a DHCP address or assign a static IP address to the device.  When I try to assign a static IP address, I get the following error:

  56-62 an error occurred when applying network settings. Check that the entered parameters are valid for the network.

  Thoughts?  Is my scanner goes wrong?

  Looks like you have a Rev A scanner and the software is for the Rev A and B

  The SW is 24.1 the the file name once you have created the bootable image and make sure they match

• Unable to drawings SolidWorks great impression for HP DesignJet 500 via Server

  Hello

  Our company has a HP DesignJet 500 with 24 "Inker for tracing large pages of design drawings created in SolidWorks to our technical workstations.  These workstations all have Windows 7 64-bit with 8 GB to 16 GB of RAM and 1 TB of hard drives and intrigue to the drawing via on board our servers (Server 2008 32 bit with 4 GB of RAM), which connects to turn over a connection IP to JetDirect EX Plus (with a sleeve of 10 Mbit / s and a CAT 5 network cable) and a parallel cable.  Lately we had problems tracing of parts of very large assembly drawings (100 MB + size), by which desktop lock when trying to trace.  They can even preview before printing (print dialog box disappears when the user clicks the Preview button).  Restart the plotter and the JetDirect gave no results better.  The server has plotter driver installed v6.08 (data file version 2.1), and the tracer itself is on firmware 3.03 version.  No errors are appearing on the plotter except an error of 79:04 in December.  Tracing a bitmap file doesn't seem to be a problem, but I could not try the other formats again.

  Any thoughts?

  Thanks in advance,

  Michael

  In the properties of the driver, there is a tab services which must display a troubleshooting icon and you can click on "Run as bitmap".  This will allow the desktop process files to print instead of the printer, which cannot process large files.  It is the only way to execute works of old printers not designed to process.

• Designjet 110Plus NR: HP Designjet 110 Plus NR Maintenance Utility does not detect printer

  Hello

  I have a Designjet 110 Plus NR printer that prints, but when you use the maintenance utility, it does not detect printer. I downloaded the latest version H.06.0 and am able to install it. but when the search for the printer it will not find it, and I have no way to pinpoint it too my printer. I have the printer connected to my computer via the USB port on a docking station HP residing in my laptop (Elitebook 800 G1 win 7 pro x 64). Also, it is connected via a parallel to the NIC dongle to make it available on the network for everyone to print too so. All can print, I can print but the Cyan is not always print and before you buy new print heads, I would like to clean and align with the Maintenance Utility. I tried to use the printer in the dock station, plugging directly into the laptop and the network to connect, but won't find printer. I tried the alignment of the front that I found in other forums, and it did not work. Whenever I went to the printer, I uninstalled all drivers and and the computer and rebooted system maintenance utilities. I installed the drivers from the HP website, from the disc initially supplied with the printer and our network, still no change print server. Am still able to print but not to run diagnostics or alignments. I've scoured the forums HP and all the "recommended" patches have never someone who in fact confirms the
  'Fix' worked. Can someone help with this problem? It has been about 4 days that I'm looking into this and frankly it's kinda ridicolous saw that it's a plug-and-play printer. Thanks in advance for any advice you may have!

  Well, the network adapter has failed. I managed to install the software, but he gave a generic IP address of the printer and gave me the same mistake of not being able to communicate with the printer. So, I pulled up an old laptop XP downloaded the drivers from the HP site, rebooted, printed the test page with success and installed the system maintenance utility. And WHOLA, I saw the printer immediately in the USB of Maintenance section and was able to run the diagnostic page and determine our problem. Thanks again for your help Mike!

• Designjet 500 prints on usb but not ethernet

  I inherited a DesignJet 500 printer 24 in. I can print so that I am related to him by a USB cable but when I try to set up on my network, I can't print to it across the network.  I can ping the JetDirect card and can telnet in as well so I know that I have the correct IP address and it the card itself can communicate with my network.  I use the same driver via the USB port and the network port but still unable to print over the network.  Any ideas why I can connect to the printer on my network, but I can't print on it unless I connected locally with a USB cable?  I tried with a laptop running XP32bit and Win7 64 bit with the same results.

  Thanks for the help.

  Thanks to the entrance to the Forum of commercial products.  BTW, I discover to my problem.  It looks like the problem was the cable used to connect to my network.  One of the things that I should have checked first, but don't have.  After replacing the cable, I was able to print from the network to it.

• Designjet 500 24 '': hp designjet 500

  I just got the printer HP Designjet 500 24 "."  I downloaded the drivers there.   I went to devices and printers and clicked on the new printer.  The designjet is not discovered.  Tried to do it manually, but I don't know my way around that.  Any tips?

  I deleted all of the printers I had and restarted the computer and tried to add again.  No dice.  He is grateful to my other main printer without problem.  Do not know how to move forward to get the designjet recognized so I can start printing my game.

  I went to the properties of the print server and the driver installed there - "HP Designjet 500 24 by HP" that still did not help.

  I found a link that has helped to explain how to add a local printer by using the tcp/ip address or the host name.  I finally got to work!  I struggled for a good 3 hours trying to find different ways to add.

• Cannot download the software due to a network problem

  Hi all I'm on MacBook Pro (retina, 15 inches, end of 2013).
  I try to install Windows 10 with the version downloaded from the Microsoft Web site.
  I finished uploaded and am trying to use Boot Camp to install Windows 10.
  However, I faced a question and it is that he "cannot download the software due to a network problem".
  I'm stuck here for an hour and I can't find a solution.
  I did all right until now by the following online tutorial but it prevents me to continue.
  Any help will be appreciated.
  Thank you.

  It is a very common problem. To fix this, first try to start your Mac in safe mode by following these steps-> safe mode try if your Mac does not commissioning - Apple Support

  Then, restart your Mac as usual and try to download the Windows support software again.

• Designjet 500 proposed purple colors AutoCAD printing gray

  We used the Designjet for years and have several colors put in place to print gray and projected (252, 253, 254 and 25).  They have recently started with purple print.  I have run all diagnostics and calibrations and alignments available, and they are all good.  I looked at several troubleshooting sites and had no luck.  I use AutoCAD v 13.

  Assuming that the print heads are out of all the colors correctly, try this:

  The printer HP Designjet 500 and 800 series printers have a fix that was implemented in the version of firmware A.02.08 and higher. This hotfix provides additional media profiles that prevent blue to mauve color output change. This fix is only applicable to the series 500 and 800 and only if the printer has a version of firmware of A.02.08 or higher. Once the firmware has been upgraded, follow the steps below to make the appropriate changes in the Panel menu front printers:
  
  1.
  
  Highlight the menu paper icon on the display on the front panel of the printer and press ENTER.
  2.
  
  Scroll to the paper type and press ENTER.
  3.
  
  Highlight Enhanced colors and press ENTER.
  4.
  
  Select the type of paper there and then press ENTER.
  5.
  
  Press the Menu key to return to the normal display of front panel

• HP DesignJet 500: HP DESIGNJET 500

  General question... I am looking to buy a little used designjet 500 and do not see in the characteristics of the product, if it is a printer and strawberry.  Can someone tell me if the designjet 500 printer 24 inches offer traced functions designed to make signs or conrour cuts?

  Thanks in advance,

  Ken

  Hello Ken,

  Designjet 500 has the ability to cut the paper/online support right (at the end of the print job to the Cup/entity roller ring at the end of the print job), but I do not think that this option fits your requirements.

  Kind regards

  Ask me

• Cannot install updates due to temporary network problems

  Hi need help please teporary network problems are interfering with windows update

  Read this: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/1467f44b-ee27-4f7d-98d7-f1c4b35b3395

  Help us help you.

  Is this relevant: you may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem? ___

  Recently, I installed Microsoft Works 9, and now I have trouble to download the Windows Update update of security for Microsoft Works 9 (KB967044). I am getting error 646. What is a network problem?
  I have also recently set up a wireless network.

  Hello

  Try this 1st to see if it helps, and it should:

  Description of the Patch registration cleanup tool
  http://support.Microsoft.com/kb/976220/

  ------------------------------------------------------

  If necessary :

  Try this - Panel - Windows Updates - on every update that will not be installed - click on the important updates
  or the update itself - double click a view more information (or click top then discovers on the right)

  Those who will take you to a page where you can download the update.

  Or go here and the KBxxxxxx number to download it.

  Download Center - mount the KBxxxxxx.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  Download - SAVE - go to where you put them - click on - RUN AS ADMIN

  Then you can right click on the update in the updates Windows and HIDE.

  If you get an error Installer install this version:

  Windows install 4.5 Redistributable
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=5A58B56F-60B6-4412-95B9-54D056D6F9F4&displaylang=en

  ----------------------------------------------------

  Then run this:

  How to reset the Windows Update components? -a Mr Fixit
  http://support.Microsoft.com/kb/971058

  Description of the system for Windows Vista, Windows Server 2008, update tool and
  for Windows 7
  http://support.Microsoft.com/kb/947821

  ------------------------------------------------------------
  Because these are all Office updates you might get more information if necessary in the Agency of those groups that
  may have experienced the same problem.

  Office newsgroups
  http://www.Microsoft.com/Office/Community/en-us/FlyoutOverview.mspx

  Microsoft.public.office.misc discussions
  http://www.Microsoft.com/communities/newsgroups/list/en-us/default.aspx?DG=Microsoft.public.Office.misc&cat=en_us_01cb749f-c998-4762-8099-df71793c11c7&lang=en&CR=us

  ------------------------------------------------------------

  If necessary you can incident free get reports however the above should take care of it for you.

  Windows updates - free Incident report

  Go here and click on-> Windows Update fails while searching, downloading or installation of updates
  http://support.Microsoft.com/GP/wusupport#tab3

  The security updates, you can get free support Incident report
  http://www.Microsoft.com/protect/resources/support.aspx

  I hope this helps and happy holidays!

  Rob - bicycle - Mark Twain said it is good.

• HP Designjet 500 42 "do not print

  Looking for help with my HP plotter. Recently, I replaced the service station and print transport. I also downloaded the driver (Driver HP DesignJet 500 PCL3GUI 32-bit) and firmware (series of printer HP Designjet 500, 510 and 800 Firmware Upgrade) to new pc XP from the original pc used for printing crashed. The printer displays indication normal and says ready for jobs however when I send a print to the printer it just shows treatment work and transport movements feeling left right at a few times, but the jobs do not print. Also, it seems to stay forever in this (suspended) mode and I have to power the printer off to return to the normal screen ready.

  What is a driver/firmware issue or hardware?

  If I try to print a configuration page it also does the same thing.

  Thanks in advance.

  Jacob

  It is a thin cable error. The ends of the cable have questions or it is not completely sitting in the cart. I guess the cable could be as bad.

• Outlook Express 6: your server has unexpectedly ended the connection. The potential causes for this include server problems, network problems, or a long period of inactivity. Error number: 0x800ccc0f

  Original title: Windows XP and Outlook Express 6

  I have a new computer with outlook express and went through the set up instructions.  When I tried to send a test email, I got this error message:

  "Your server has terminated suddenly the connection. The possible causes for this include server problems, network problems, or a long period of inactivity. Account: 'pop.mail.yahoo.com', server: 'pop.mail.yahoo.com', Protocol: POP3, Port: 110, secure (SSL): Yes, error number: 0x800CCC0F. »

  How can I fix this error message and have e-mail sent via Outlook?

  Hi Jeanette Logan,
   
  Here is an article that addresses this issue. Follow the steps listed in the article for this problem:
   
  Troubleshooting error messages that you receive when you try to send and receive e-mail in Outlook and Outlook Express

• Wireless network problem: disconnects randomly anywhere between 1 and 4 hours.

  I have a wireless network problem, it disconnects randomly anywhere between 1 h and 4 h. The network consists of a Samsung 4 G hotspot and a Linksys AE1000. The signal strength is excellent, the AE1000 is 1 ft of the computer and 1 ft of the HotSpot.  The computer is a Dell Dimension 2400. Any ideas?

  Hi Jack,

  Problem solved.  I did 2 assumptions about the original problem.  I assumed that the 2 Tech that I spoke made the hurt their product. Battery saver has been activated on the hotspot.

  Thanks again

  Greg