HP Deskjet 722 c - connection LPT to USB 2.0

Similar Questions

• DeskJet 6940: ethernet connection between the new modem and printer does not transmit Mac

  I just installed a new modem to Qwest; It works wirelessly with my iMac 10.11. My old (but functional until yesterday) Deskjet 6940 is connected to the modem via Ethernet. When I try to print, the document seems to be transmitted to the printer, but then it hangs on and I get the message "the printer is not connected" - which it is, plugged, ethernetted, and set in motion. Support of Qwest says that only 10% of the info from the computer are the printer, but he seems to think that the part of the new modem Ethernet is functional,

  I have already tried all unplug/restart/send/add printer new check/updates / IP (cannot connect) / ethernet ports and cables, etc.

  Any other ideas?

  Thank you!

  Hi @newgranny,

  Thanks for getting back to me.

  It is good that the printer has been able to print a diagnostic page.

  Ensure that the router and firewall on the market do not block these ports.

  • About the application firewall

  Ports of printing:

  • UDP ports: 427, 137, 161
  • TCP port: 9100

  Card photo upload:

  • UDP ports: 137, 138, 427
  • TCP port: 139

  The HP device status:

  • UDP port: 161

  Ports of Web Services:

  • UDP and TCP: 80, 443, 5222 and 5223

  Hello Ports:

  • TCP and UDP: 5353 and 5297, 5298

  Unplug the wired network (ethernet cable), restore the default values on the printer.

  Restore the default settings.

  Follow these steps to reset the printer to factory default settings:

  1. check that the printer is on.

  2. press and hold down the button to report Page.

  3 while holding down three times the homepage button, press the Cancel button.

  4. release the report Page button.

  Source

  • Restart the printer.
  • Connect the ethernet cable.
  • What were the results?

  If the problem persists, try the USB connection.

  Please reply to this message with the results. Good luck!

• Deskjet 3050 a problem change from USB to wireless

  I got a Deskjet 3050 a printer attached via the USB port of my desktop HP Win7 64 bit for a year and a half. Attempts to convert the USB wireless. Instructions lead me the start--> all programs--> HP--> HP Deskjet 3050 J611 series a--> convert USB wireless.

  But when I open--> series HP Deskjet 3050 a J611, my only choice is:

  Connect a new printer or

  Add new software

  Nothing on the conversion of wireless USB. If I click 'connect a new printer' I have the choice of:

  USB connection

  Connection Ethernet / wireless

  Connect again later

  If I select wireless connection, it tells me to connect the USB cable. It is been connected for more than a year. But the button "Next" is gray and I can't move forward.

  If I select USB connection, it tells me to connect the USB cable. It is been connected for a year. The only choices I have are to return to a screen or check a box that says I'll connect it later, not now. I don't have to check but the 'Skip' button is gray and so I'm stuck again. I tried to turn the printer power off and moving the USB cable to the USB port of different desktop and power on printer again. I tried to reset the default printer on the printer control panel. The software does not believe that the USB is connected. This is the case.

  I pressed the button on the control panel of the printer wireless. It flashes blue.

  I'm usually pretty good with the resolution of this kind of thing, but I'm ready to break this piece of scrap on the ground and dance on his grave. .. .any help would be appreciated. Thank you!

  Hi Julie,.

  Thanks for the reply, sorry for the frustration. Here's what to do to uninstall it, in a more detailed form.

  • Click on the link above to access the driver removal tool.
  • Click on download and run.
  • Click 'Yes' when asked if you want to allow the following program to make changes to the computer.
  • A folder opens, look down and you'll see 'uninstall_l3' - select it.
  • The uninstall is running and restarts your computer.

  Now, it is normal to go forward, and then reinstall the printer.

  I hope this helps you, let me know how it goes!

• ZTE open not light unless it is connected to the USB power source.

  Even with the battery fully charged, my ZTE open never turn on unless it is connected to a USB power source. Once connected, it can be started, behaves normally and can be disconnected.

  You should contact the owner of the eBay store in this case.

• Message: This device can perform faster if you connect high speed USB

  Hello

  I have a laptop Toshiba Satellite 2009 of Vista.
  I just bought a multimedia design Memup Feel of the disc hard 500 GB.

  My concern is that when I connect to my PC, I have the following message:
  + This device can perform faster. USB devices can be faster if you connect to a USB 2.0 high speed +.
  + To get the list of available ports, click here. +

  Then I have a list of ports in bold, but I don't know what to do with.

  How to solve my problem?

  Thank you

  Hello

  Are you sure that your laptop is Satellite 2009?
  I put t know this model of laptop.

  But I know that this error message; This message appears if you connect a USB 2.0 device to a slower USB port; That is, USB 1.1
  But I think that your laptop supports USB 2.0 ports either TI problem disc external HARD s or the issue of USB drivers
  Try updating the chipset driver you can also delete all the USB controllers and hubs in Device Manager ports. Restart the unit. After restarting again the OS would recognize all USB ports.
  Then try to reconnect the USB HDD

• Cannot connect camera Basler USB 3.0 to IMAX

  Hi all

  I have a few question about connect the Basler USB 3.0 camera with LabVIEW.

  I use camera Basler acA1600-20um, it does not appear on my NOR-MAX.

  in fact, there are only "Basler USB3 Vision camera 'USB-0' ace' and the error when I try to click on it.

  Can someone help me?

  Thank you

  Racha

  Thanks for posting the error screenshot...
  -You have been able to connect using Basler pylon software?
  -can you right click on the "Basler USB3 Vision camera 'USB-0' ace and the driver NI-IMAQdx and then see the change?

• Connection of the USB camera - OR-IMAQ for USB cameras installation problems

  I tried to install the usb http://zone.ni.com/devzone/cda/epd/p/id/5030 camera application

  Unfortunately it does not work. I don't know the usb icons in my function palette. can you help me please?

  I want to only connect a camera usb with labview. How can it be difficult. any help would be appreciated.

  see you soon

  Hello

  You first need to make sure that the USB camera is DirectShow compatible.  If it is not it will not work with the software of our vision. You must use the drivers IMAQdx (which requires a license) to acquire from a USB webcam.  Once you have installed the drivers IMAQdx (Vision Acquisition Software) and drivers that come with the webcam is installed, you should be able to see it able & Automation Explorer (MAX).  Once you can see it in MAX you can use it like any other device in LabVIEW.

  Kind regards

  Greg H.

• My laptop does not recognize that anything that is connected to the USB ports

  Help, please. My laptop does not recognize that anything that is connected to the USB ports.

  Moved from feedback

  Original title: problems with USB ports

  Hi Alba.

  1. who is the operating system installed on the computer?

  2. What is the brand and model of the computer?

  This issue may be caused if one of the following situations arises:

  • The currently loaded USB driver has become corrupt or unstable
  • Your PC requires an update for problems that could conflict with an external hard drive USB and Windows
  • Windows may be missing other problems hardware or software updates
  • Your USB controllers may have become corrupt or unstable
  • External drive can enter selective suspend
  • Your PC motherboard may need updated drivers

  I suggest to connect the USB device to a different USB port and check.

  You can run the Fixit provided in the article and the Coachman.

  Reference:

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems

  You can also try the steps in the link and check if it helps:

  Reference:

  Tips for solving problems of USB devices
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

  Note: Apply to Windows 7 as well

  Hope this information helps. Response with status so that we can help you.

• The Epson Workforce 600 is connected via a usb cable, the other is a wireless network. I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it does not list

  I have two printers installed on my laptop, only appears.  The Epson Workforce 600 is connected via a usb cable, the other is a wireless network.  I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it is not the list when I go to print something.  When I select "Find a printer", it gives me a list of computer icons.

  Hello

  Check with Epson support, their documentatiion online and drivers. As it's Epson OEM
  responsible for the proper functioning of the printer and their drivers provided.

  Good luck, you need to update or reinstall the latest driver.

  Epson - Support us.
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?BV_UseBVCookie=Yes

  Epson - support from Europe
  http://www.Epson.co.UK/support

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• LT2323z - connect to the USB 3.0 Port Replicator

  I just bought the LT2323z monitor to go with a X carbon 1 and connect via the USB 3.0 port replicator.
  However the LT2323z has displayport digital connections and the DVI-d port replicator. Any ideas how to connect to their place? Here are the flagship of Lenovo products, bought directly with Lenovo, but they do not seem to be compatible. I'm missing something until I send them all back for my money!

  The LT2323z, take the VGA connection, which takes care of your USB docking station 3.0 with the adapter DVI to VGA, which is included in the box. But the quality of the video connection is not terrible.

  There is no solution from docking station USB supported displayport. If you need to connect to the screen, you must use a direct miniDP to DP cable connector (which is unfortunate).

• Not able to connect to Wifi, USB ports, bluetooth

  Hello team

  I bought the new HP laptop today. I have installed Windows 7 OS. I am not able to connect to Wifi, not be able to use the blue tooth, not be connected to the USB. I downloaded the drivers from the website of the other computer. But how can I install it with one of them works. Please help us on the question mentioned.

  Product number: G8D85PA #ACJ

  Thank you

  Sunil

  Hi Sunil_motukuri,

  Thank you for visiting the Forums HP's Support and Welcome.I would be happy to help you. I read your thread on your computer laptop 15-g030au HP and who need wireless for Windows 7 drivers. Here is a link to the drivers.

  Hope this helps you.

  Thank you.

• USB 3.0 connecting high-speed USB 2.0 drive

  I have a Western Digital 1 TB USB 3.0 external hard drive. I connect it to the USB 3.0 port (blue) on my laptop Acer Aspire 5755-6647, who works under Windows 7 x 64.

  When you connect, I get the "this device can perform faster: this USB mass storage device can transfer information faster if you connect it to a Super Speed USB 3.0 port" message. When you copy files to the drive, I get about 32 MB/s, which corresponds to a USB 2.0 speed.

  I tried to disable the USB power management in the utility USB 3.0 host controller. I tried to uninstall the device and put it back. I'm using the cable supplied with the disc and is a USB 3.0 cable. I have the latest Renesas USB 3.0 driver installed (2.0.34.0). I also tried to use an older driver from Renesas. My BIOS is updated (P5WE0121).

  I don't know what else to do. If it helps, the first time I have connected my laptop hard drive, it's on a USB 2.0 port (I had for some reason any remembered which side of the laptop had the port 3.0 and does not check for blue). As I have said, however, I completely uninstalled the device. I suspect that Windows can be "remember" the device and install with the 2.0 driver.

  Update: I finally try one last thing before you go to Acer support. I thought that perhaps not enough power provided by my USB 3.0 port on the drive, forcing him to 'downgrade' 2.0. So I bought a cable to Yfor $5 to offer auxiliary power of the adjacent 2.0 port. Result: IT WORKS. Immediately connected as a USB 3.0 peripheral speed and transfer is USB 3.0.

  Solved. A little disappointed with the Acer/Intel for the USB 3.0 under normal, however.

• Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Service Pack 3 for Windows XP does not recognize that it is connected to the USB ports. I get a notice that something has been plugged, but Windows fails to recognize regardless of the question.

  Disconnect all USB storage.

  Run this tool by do right click and choose 'run as administrator '.

  Of course, all first extract it:

  http://www.Uwe-Sieber.de/files/drivecleanup.zip

  If your XP is 32 bits, use the Win32 folder.

  Reset.

  If you still can't find the drive, assign it a drive letter in disk management.

• I use a third party inf file when creating a network connection via my USB port. The USB connection will become inadmissible and also cause the laptop hang up.

  I use a third party inf file when creating a network connection via my USB port. The USB connection will become inadmissible and also cause the laptop hang up. Currently I try to modify the INF file but is seeking a help or suggestions in T/S to this problem. Thank you.

  original title: third party INF problems

  Hi Paul,.

  ·         Why are you using a USB port to create a network connection instead of using an Ethernet connection?

  You can see the following article on how to set up a network.

  How to set up a small network with Windows XP Home Edition (PART 1)

• How can I change the default actions of what made the PC when I connect a camera, USB key, etc.?

  How can I change the default actions of what made the PC when I connect a camera, USB key, etc.. My Samsung intensity II is what I need it for; I want to shoot to the top of this window asking me what to do when I plug in, but one day, I was not thought and press on 'No Action' with the "always perform this action for this device" (or said something like that) checkbox checked.

  Once it is connected, go to my computer, and your camera photo or anything else that should be there.  If is isn't, it is a completely different issue.  It's done, right-click on it and select Properties.  Click the AutoPlay tab.  There is a version of dialogue enough of this "window asking me what to do."  You can figure out what to do from there.