HP DX2450 format microtour slow start on the POST screen.

Similar Questions

• Compaq Presario CQ5504F at the start of the POST screen, then freezes, does not recognize the hard drive

  My Compaq Presario CQ5504F desktop computer (about 4 years) turns on, displays which I assume is a POST screen shows:

  As of the 2010 AMIBIOS Bios, Bios Rev. 6.08, 28/04/2010, CPU AMD Sempron 140 2.70 GHz 1024 KB ram Cache (L2)

  Installed memory: 3072 MB, installed USB controllers.

  Correctly displays "1 drive ST3500418AS" (seagate 500 GB SATA h/p) and "HP DDVDW TS-H653R" (optical drive)

  Tried a "HP Bootable Diagnostic CD - R' which took"PC-Doctor ".

  CPU Sempron tested and passed and 3072 MB of RAM and the HP DDVDW disc.

  Next: "Testing: path of the boot!" WARNING - BIOHD-2 error code.   WARNING: no hard drive detected ", followed by proposals to check the cables, etc.."

  Also shown: "NVIDEA Boot Agent 249.0542?

  I opened the system unit and disconnected - reconnected the two connectors on the h/d.  checked sound & vibration watch Variator is running.

  Also checked "Boot Device Priority:

  1 > [CD-ROM Group]-[HP DDVDW TS-H653R]

  2nd > [Hard Drive Group]-[not installed]?

  3rd > [group floppy]-[not installed]

  4th > [group of network boot]-[NVIDIA boot agent]

  Found a few useful tips on PC Help Forum, but advice required to enter the BIOS Setup, and I have not found a way to get into that.  Some of the function keys don't seem to work.  ????

  Would be very happy to suggest further repair attempts.

  VIC

  VIC, welcome to the forum.

  Normally, the BIOHD-2 error message indicates that the hard drive has failed.  Here's a guide to help you run the SMART for the reader of the BIOS test.  If you get a similar error message, you must replace the hard drive.  Also, here is a guide to help the recovery of the system once the drive has been replaced.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Satellite M40 - 129 stops starting after the Toshiba screen

  Hello
  My M40 continues sometimes to start after the Toshiba screen. He stops and all I see is the blinking cursor. No Error Message or something else and normal boot from the HARD drive. Boot from CD (for example. Œuvres of Knoppix). This problem sometimes occurs and traceable for me isn´t.

  Best regards
  Spoony

  Hey Spoony

  Unfortunately on this path, it is not easy to say why this is happening. Each user has a specific configuration OS and we don t know how your operating system is configured.

  You can boot OS in safe mode? If Yes check what the problem may be a little. If there is anything you can do I recommend you save all your data and preinstall unit using rescue media. If you do this I recommend also to create two partitions.

  Don t compare WXP and Linux startup procedure. As you know that Knoppix using just the RAM and no HARD drive for the race.

• My computer starts slowly by post screen 20 second delay at the HP logo screen

  Hello

  My computer starts slowly by post screen 20 second delay at the HP logo screen. I tried to have this computer in past the test post screen or simply to show the hp logo screen. I wonder if the MBR master boot record some how got messed up. I am running XP Home Edition not windows based anti-virus software
  I think the motherboard is a MSI KM4AM - V AMD athlon XP 2500 + or 2600 + processor I think 3200 400 MHZ memory 2 512 MB memory sticks. Hard drive 80 GB
  There is no other setting in the bios for a quick start

  Sorry about that.

• my system starts after the logon screen because someone entered a user profile with password that I can't not spent to get to the bone. Y at - it a nother password I can use to get the operating system up so I can edit user accounts? ___

  When I try in safe mode with command prompt, it starts at the Welcome screen and not in safe mode.

  Hello

  No, you need the password. The Microsoft strategy for these forums banned help users circumvent passwords.

  In safe mode, there is a default Administrator account that can be used to reset other user accounts.

  Good luck, Rick Rogers, aka "Crazy" - Microsoft MVP http://mvp.support.microsoft.com Windows help - www.rickrogers.org

• Cannot start after the blue screen "page in the nonpaged area failure."

  My sons laptop has got to me.  There the error page blue to come with "failure page in the nonpaged area." There is a chain of technical info of numbers, but this changes a little at each attempt.

  I tried all F8 options, without success.  I did a restore disk from the laptop of my other son (which is the same) and that has not worked and I also downloaded a file of system restore on the internet who do not.  I ran diagnostics memory on the scope option and who found nothing.

  No matter what I try, always the fails to start after the first screen with Microsoft Corporation at the bottom and the small lights of scrolling!

  I would be grateful for any suggestions that anyone can have.  I wondered if I should try to borrow a disc of Windows Vista from someone and try from there?

  Read the messages and follow the procedures established by the MVP of the spirit in the following thread on the Blue Screen of Death.  They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.

  I hope this helps.

  Good luck! Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• HP Compaq dx2300 format microtour CPU Upgrade requires the bios update

  Hey, my Hp compaq dx2300 format microtour came with a core2duo E4400 processor, I had an E8400 CPU because they share the same socket LGA compatible on the motherboard and it fits perfectly, only the pc does not start, then read around some sites say it is supported by my MSI motherboard A 0, 90, others only reported up to E6700 what I don't understand, is why it wouldn't work? I BIOS v1.14 (latest news on the list of dated drivers '2008'!) and can't seem to find a solution for this, please tell me what to do I don't want to be stuck with a CPU, I can't use cause it isn't a way to map mother read it, thanks in advance!

  Hello:

  Unfortunately, you're stuck with an E8400 which won't work in this PC.  See page 4.

  Here are links to the quickspecs for your model.

  http://h18000.www1.HP.com/products/QuickSpecs/12668_na/12668_na.PDF

  An E8400 processor will not work in any case with x chipset Intel 94 or 96 x chipset.

  In order to run an E8400 into a PC, there need an Intel 3 series chipset or 4 of the series.

  Of course a processor must adapt to an outlet, but is not the only criterion needed to make it work.

• updated to 16 MB on 2011 iMac 27.5 inch quad core will cause a slow start to the top?

  Have 27.5 inch iMac OSX 10.11.3 computer. The memory of 4 MB.  Recently updated to 16 MB.  Now have the very slow start up.  15 minutes.

  Should take 15 minutes to initialize 16 MB on a quad core computer?

  ewcbhc wrote:

  Have 27.5 inch iMac OSX 10.11.3 computer. The memory of 4 MB.  Recently updated to 16 MB.  Now have the very slow start up.  15 minutes.

  Should take 15 minutes to initialize 16 MB on a quad core computer?

  If you put expensive RAM and/or incorrect RAM then Yes. iMacs are very sensitive to the RAM and you must use quality RAM, more experienced on these forums users use OWC (www.macsales.com) or critical (direct purchase). RAM should also be installed in pairs. If you purchased anything else, then after a report of EtreCheck of your system and we can look for obvious problems.

• Satellite U400 - color of the shell of edges and slow start of the housing

  Hi all

  Just bought a Satellite U400-15B and am loving the laptop itself but have the following two issues.

  First of all, regarding the case I noticed that on the edge of the high gloss base (where he meets the not shiny black plastic bottom) the paint is already peeling.

  It is mainly about above the left USB port, CD drive in Rabat and at the rear above the battery (only visible when the lid is closed). It is very minor and is only visible when looked at her carefully, but obviously I paid a lot for this so do not want to look all worn in a few months. Someone at - it? I took a look at a few display models and its mixed, some are worn in areas similar some are perfect. I would like to exchange it, but I'm afraid that the replacement can be another problem like a dead pixel or may have the same problem only worse?

  Second, I noticed that my laptop takes a long time to start compared to my old Toshiba A200 which also runs Vista. I removed a lot of bloatware and the Toshiba TEMPRO, which I heard is also causing problems, but I still have this problem. It seems to start fine until the Vista logo screen then it takes awhile, while displaying "Please wait".

  Anyone has any ideas on this?

  Hello MrAK

  If the laptop is brand new and you have a few days only I recommend you contact your dealer as soon as possible and. Talk with them and explain that you don't want to have replacement with dead Pixel or something like that. I hope they will understand you and help get new but 100% good laptop.

  Slow start is discussed several times. I have Satellite A300 and commissioning was horrible, but now, after a slight modification it starts after only 1.5 minutes.
  Check my ad under http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=134947

  Bye and good luck

• Slow start of the missing files?

  I recently deleted some .tmp files and since Windows XP (SP3) is very slow to start. I did a clean boot and it takes so much time. The delay occurs after the Welcome screen disappears from the screen and lasts a little more than a minute. After the start, everything seems to work normally.

  Is the delay caused by Windows looking for missing files? If so, do I have to reload from CD and then reinstall SP3?

  This was due to an update for .NET Framework 4. My actions have been a coincidence.

  See: KB 2571181 for a fix.

• Satellite U940 Windows 10 update, very slow start to the top

  Hello

  It looks after upgrade to win10, the SSD is not used to quickly boot up the laptop.
  How can this problem be solved?

  In tools, defragment disc, it shows all of my partitions as SSD drive so I can't defragment.
  Why are they displayed as SSD? I think that the basic motivation is a 500 gb HHD and only a 32 GB SSD is included.

  Also in the management of the computer disk SSD drive shows only 11.22 GB of capacity and is not used (all 11.22 GB free)

  Help, please. I want to get the quick start of the win8.1 and at the same time be able to defragment my HARD drive.

  Posted by some_user
  

  Hello

  It looks after upgrade to win10, the SSD is not used to quickly boot up the laptop.
  How can this problem be solved?

  In tools, defragment disc, it shows all of my partitions as SSD drive so I can't defragment.
  Why are they displayed as SSD? I think that the basic motivation is a 500 gb HHD and only a 32 GB SSD is included.

  Also in the management of the computer disk SSD drive shows only 11.22 GB of capacity and is not used (all 11.22 GB free)

  Help, please. I want to get the quick start of the win8.1 and at the same time be able to defragment my HARD drive.

  Hello

  Same problem here with a weak start after the upgrade to Windows 10 (with a Satellite U940-11 t).
  If anyone has the solution, it could be great :-)

  EDIT: I just saw this post: https://forum.toshiba.eu/showthread...-to-Windows-10
  I will try this solution.

• Windows 7 x 64 extremely slow start and the screen 'welcome. '

  Hello!
  I have a laptop Toshiba Satellite A500:

  Intel C2D 2.5 GHz
  4 GB DDRII 800 MHz RAM
  400 GB 5400 RPM Toshiba HDD
  ATi 4650 GPU

  I have Windows 7 Pro X 64 OS real, through MSDNAA

  The boot takes 17-21 seconds on the Welcome screen (20-30 seconds ' welcome'), then 1-3 minutes on open office.
  I have all the drivers installed, I tried to start the removal of unnecessary startup programs, but it's the same thing, only 1-5 second faster.
  I reinstalled my OS several times, the HARD drive is in AHCI mode, but I tried to 'Compatibility', but does not solve the problem.
  After bootlogo, there is very high HARD drive activity (people with disabilities search indexer and superfetch too)
  With x 86 startup is about 1 min.

  I suggest a bit of required diagnosis. Try this [how to solve a problem by performing a clean boot in Windows Vista or Windows 7 | http://support.microsoft.com/kb/929135]

• Unable to start before the Welcome screen - error Code: 0 x 00000050

  original title: can not go beyond the Welcome screen, or the safe mode works - Vista

  About 2 days ago I received the 'blue screen of death '. I tried to connect to the main user account, but the screen would not go further than the Welcome screen. I then tried to open a session through safe mode, but that no longer works. After a few tries to connect to my user account, I tried to log in through the guest account, which has worked. The guest account has worked as it should, I was also able to use the internet. After that I tried to connect it to my main account again, but it still does not work. If anyone can help me with this, ID really appreciate it!

  Here's what I got on the blue screen of death:

  STOP: 0 X 00000050 (0XC084A5F1, 0X00000000, 0X00000000, 0X826C1498)

  Data collection for the crashdump...

  initialization of the disk for the crashdump...

  Dump start for the physical memory to disk: 100

  Total physical memory dump.

  If this does not resolve the problem: Please reinstall your copy of windows vista completely

  Depending on the symptoms, it is very likely that this problem is caused by a conflict with third-party drivers or services. If you have a back up of all your data, please reinstall the operating system. A new installation of Windows Vista is always an effective way to solve such a problem. After formatting the hard drive and reinstall Windows Vista, we will obtain a new installation of Windows Vista. It is more stable than the current system.

  I look forward to your reply

  If this post can help solve your problem, please click the 'Mark as answer"or if you find it useful, mark it as useful by clicking the 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Mac does not start at the login screen

  I have a Macbook Pro (15-inch, mid-2014) that will not stat upward, toward the top of the login screen.    It starts in a circle with a line crossing.

  It has a processor Intel i5 with 4 GB of memory and 256 GB of Flash storage.

  The Macbook Pro is on OS X 10.10.5... Yosemite.

  I tried to start it in safe mode by pressing on * during the shift and no resolution.

  Can someone help me?

  You have a good backup?

  Try restarting your recovery volume. Follow the directions for your problem.

  On the screens, you see when you start your Mac - Apple Support

• My iMac will not start past the gray screen

  At startup, the iMac rings and goes to the grey screen where he hangs up and does not progress.

  I tried with the command/R button from Mac, but the utility never appears.

  I tried to start with the SHIFT key down... same thing.

  Is there something I can do?

  Thank you very much!

  Paul,

  My iMac (early 2010) has just started doing the same thing.  Initially, I could start in recovery mode, but download time was 18 hours and time increased.  I stopped the download and downloaded the installation on a USB disk on my MacBookPro in the hopes that I could start the iMac to the USB instead soon and not tomorrow. Now, I can't get the computer to boot on the USB stick or the recovery partition.

  So he can start on the USB key you must hold down the option key when you hear the chimes boot.  Then maybe you can try and have some success.

  If you find something that works to post here, if you think about it!

  Good luck!