HP EliteDesk 800 G1 TWR: no noise... must unplug/plug the front panel

Similar Questions

• P1G44EA #A2N -: instalation HP EliteDesk 800 G2 Twr PC scanner error

  HELLO Support,

  I'm unable to install hp scanjet G4010 in HP EliteDesk 800 G2 Twr, I get this error.

  Hello
  Click the Start button and type folder in the search bar, then open the Temp folder indicated.

  Open the last HP installation folder that begins with 7z (e.g. 7zs1234)
  Open the installation folder.
  Find the file usbready.exe and rename it to usbready.old.exe
  Navigate to the main extraction folder (folders that begins with 7z) and run the Setup.exe file.

  Now follow the installation and check for the difference.

  Kind regards
  Shlomi

• HP EliteDesk 800 G1 TWR: EliteDesk 800 G1 TWR - no Intel-vt option in bios

  I'm trying to VM Player allows you to create a virtual machine of several of our machines for deployment purposes.  Although we have 3 different models of PC, they use all PheonixBios.  To create the virtual machine, I need to enable Intel-vt in the bios but I don't see any option to do so.  I looked at the processor i7-4770 and it should support Intel-vt.

  Any suggestions?

  unngg nevermind, I misunderstood something

• HP EliteDesk 800 G2 Small Form: The front panel audio connector - this only made type to use for headphones and microphone

  Hello

  I am trying to determine what type of audio 3.5 mm plug to put into the connector on the front panel for the use of a headset to make video communications.

  could be - sleeve, ring and end cap (mono audio and microphone)

  or

  could be - sleeve, ring, ring and tip (stereo sound and microphone)

  Having read through the manuals and nothing is said on the type to use.

  Hello world

  Just plugged the connector 4 poles on my headset combination for my mobile phone (cellular) and the box of pop - up asked me to select headset or microphone - no selection for both.

  Looks like the right sleeve is for headphones only, and the left one is for headphones or micro - selectable by the user and not the two on a single sheet.

  Everything explained by the practice - but not the paperwork in the manuals.

  #5 for microphone or headset - menu popup is displayed after you insert a 3.5 mm plug to select that one but not both at the same time.  (So I can't use my headset to phone)

  Thank you

  Son

• I have touchmate pc it isn't its rear panel, I maen when I plug the rear panel speaker there is no noise, but when I plug frontpanel works. Prior to the two panel was allso helmet is the same proplem

  no sound  I get this problem when when I started using headphpne and speaker at the same time, and it coused stop working together. I tried to fix it I not unhooked device and Istalled kdshjfk but after speaker instalation and haedphone work only on the front. Mark I will get help. Thank you

  Hello misibij,

  1. remember you to make changes to the computer (hardware or software) before having this problem?

  This problem may be related to your computer hardware. The front and rear taken on a computer operate on different sound cards. If the sound does not play on the rear socket, you can try to reinstall the drivers for the sound card that you have already tried. If still fails to play sound on your computer. I suggest that you check if the sound card on the computer is defective. You can contact Touchmate help you with this.

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit our Microsoft answers feedback Forum and let us know what you think.

• strange noise similar to plug the sound on my lap top

  
  

  while Im on my lap top I keep getting a sound that looks like something trying to connect for example printer etc I don't know how to find out what it is. The sound happens continuously

  Start event (type eventvwr.msc/s in start - all programs - Viewer
  Accessories - Run) and go into the Windows logs - system and see if there is
  There are clues.
   
  --
  ..
  --
  "sylviasmurf" wrote in message news: 35731487-888 d-4dce-8002-464604b85fa1...
  > thank you, I tried that and it is disconnected from the unit or device
  > Connect how to find what it is a sound that is causing this to happen?
   
   

• EliteDesk 800 800 TWR G1: > > > media presence check then no option to boot from

  Hello Sir

  I buy a HP EliteDesk 800 G1 TWR Telechareger pc. By default, Windows loded 8.1.I want to load windows 7 x 86 in this pc, so I inserct win 7 disc then reboot & system is restsrted ite system start-up

  > Media presence check then no option to start

  Please solve my problem

  Prabhu Prasad

  [Personal information]

  Immediately after turning the power on, press the ESC key. In the menu that opens, tap F9 Boot options.

  BTW you need to maybe get into the BIOS setup and disable Secure Boot to allow booting from the CD/DVD.

• HP Elitedesk 800 G2 SFF: external hard drive not detected in the BIOS. Only USB Flash drives are detected.

  Hi all

  I received recently 2 new HP desktop computers.

  HP Elitedesk 800 G2 SFF

  HP Elitedesk 800 G2 TWR

  The goal is to test our real W7 x 64 image on these machines and to inject the missing drivers in the image.

  MDT 2010 to create a deployment on a USB hard disk drive.

  This disc of deployment is already used on 16 different models of HP in the company (Elitebook, zBook, EliteDesk) to install our image so I know it works.

  Unfortunately, the two HP Elitedesk 800 G2, I can't start the boot disk but I cannot to USB for a USB key.

  The USB drive is not detected and not proposed in the BIOS Menu of STARTUP.

  Only the internal HD, external USB Flash Disk, DVD and network devices are detected.

  Here's what I already checked or tried:

  • Latest Version of the BIOS installed (2.05)
  • UEFI Boot has been disabled. (not supported by our record of deployment)
  • USB ports are enabled (front and rear).
  • All types of USB devices are allowed in the BIOS
  • The start command has been changed to start with USB devices.
  • Legacy support is active and Secure Boot disabled
  • Delete the keys to secure boot
  • Reset secure by default startup keys
  • This morning, I created a new disk deployment on a USB Flash drive and it works!

  So, it seems that only Flash USB drives are detected.

  I know it is possible to return the flag removalble on a USB device to cheat the system and make it appear as a disk fixed, but I want a simple solution.

  Does anyone know a fix or a workaround for this problem?

  Thanks in advance!

  For those interested in the answer, here's the final results.

  It turns out that the hard 500 GB external drive can be detected if it is fomatted in FAT32.

  It's strange because my 16 GB USB Flash drive formatted in NTFS works very well.

  In any case, I'll create a FAT32 Partition to the Boot MDT files and put my picture (because the file is too big for FAT32 partition) on the secondary partition (formatted as NTFS).

  Thanks to the technical pre-sales team of HP who helped me with this!

• PC HP EliteDesk 800 G1 [j4u87e: PC HP EliteDesk 800 G1 [j4u87ea]]

  Nice day!
  Have PC HP EliteDesk 800 G1 [j4u87ea]. He installed a KINGSTON SSD HyperX SHPM2280P2H / 480G 480 GB PCI-E AIC (-expansion card), how to set the Bios from this drive, run Windows? The system sees and uses it as a single disc, but not bootable.

  Hello

  Here are my suggestions:

  1. Disconnect the original boot drive.
  2. The BIOS must be set to UEFI mode.  Make sure that only the settings of the BIOS to the PCI-E slot exactly match the requirements of the PCI-E card.
  3. Load Windows 8.1 retail for the PCI-E SSD (8.1 Windows must have the proper drivers) or use the recovery Windows 8.1 media outside HP.

  If your PC does not start, then you will need to check from Kingston to determine if the PCI-E card requires preparation.

• How to enable virtualization on hp elitedesk 800 g1?

  My desktop hp elitedesk 800 G1 and installed with 64-bit Windows 7. When run the virtual machine or vmware it inform me to enable virtualization in BIOS, but I counldn can't find where to enable virtualization in the BIOS setting (entry in the decoration by press F10 during restart). Any suggestions will be appreciated!

  Hello:

  I don't have your model, but nowadays, to access the BIOS on most of these new PC you must type the ESC at the beginning of the HP welcome screen button to display a menu of options.

  Then, you select the F10 Setup option and enter the BIOS.

  Normally activate VT definition is in the Security menu.

• New HP Elitedesk 800 G1 - no wireless adapter?

  I have a HP EliteDesk 800 G1 nine compact PC running Windows 7 - code H5T99EA. It does not have a wireless adapter - certainly none appear in the profile of Harware.

  I can only connect to the Internet via an ethernet cable. I have no option to connect wireless and my wireless router is not discovered when I try (or any other local Wi - Fi access point.

  Do I have to download a driver for the wireless card - no doubt, there is one installed?

  Thank you

  John

  Is an optional scheme, see the specification page 4.

  Integrated Intel® I217LM Gigabit network connection; available wireless LAN card

  http://www.HP.com/hpinfo/newsroom/press_kits/2013/HPDiscover2013/HPEliteDesk800_datasheet.PDF

• EliteDesk 800 G1 USDT: usb ports do not provide enough power

  We have a scanner usb requiring 500mA of power.  However, for many of our clients using HPs, the usb ports do not provide enough power to the scanner causing the application to crash.  Some customers use the HP EliteDesk 800 G1 USDT, others use HP zero client t310.  Connect the scanner to a usb hub powered solves the problem every time.

  Y at - it changes, they can do for the Bus USB controllers to ensure that a particular port will be able to provide 500mA so they did not need to buy a usb powered a system hub?  Or do you have another suggestion?

  Thanks in advance.

  I'm not familiar witht eh models accurate but 500MA is the output for USB 2.0 max but 3.0 can go higher have you tried usingn 3.0 ports if not you can also get a cable Hat uses the power of 2 ports.  Many systems have problems with the only Scanners USB and power supply.

• Elitedesk 800 LTS G1 reboot on its own

  Hello

  We have 20 units of Elitedesk 800 G1 SFF; running Windows 7 Pro 64 bit.  One unit, an intermittent problem.

  Use Shutdown of Windows, the computer turns off.  Some time later, during the night, it turns back on.

  Interesting note: we have a power-password set in the BIOS and turning on the results of the computer at a password prompt.  When this unit restarts randomly, it seems to bypass the password and goes directly to screen ctrl alt del to log into Windows.

  I tried to turn off all "wake" options I find for the NIC, the mouse, the BIOS settings and even tried the registry to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon «PowerdownAfterShutdown» hack

  The BIOS, Chipset are updated, as are all the other drivers offered by HP.

  I witnessed the restart once - I stopped, looked at the front of the computer, all the lights were out, and it restarted.  I had not touched a thing.  Of course, I him didn't restart like that in front of me again. :-\

  Additional ideas?

  Thnaks

  Call our hp elite support @ 1-800-334-5144

• 800 LTS G2 Elitedesk: How to enable legacy boot on Elitedesk 800 G2

  Hi all

  We recently received a sample Elitedesk 800 G2 unit so that we can tailor our solution for OS deployment him before that people in our society early buying.

  We use the PXE-boot legacy for deployments so I wanted to set up the machine to make Legacy Boot and set the inherited from PXE first boot order.

  Since there is no documentation or the help that I could find, it is a process of trial and error.

  I finally managed to get boot inherited the machine by setting secure boot "Enable and disable secure boot" "Advanced" slot and allows the setting "secure boot claire keys»

  After a reboot, I was able to disable UEFI and configure the boot order inherited as you wish. Everything worked well.

  To validate the procedure I returned the machine back to factory defaults and tried to follow the same steps, but now the parameter 'start secured clear keys' are grayed out and I can't set 'enable and disable secure boot '.

  Anyone know how I can get back to boot legacy now? Any help would be greatly appreciated.

  I thought about it myself, it's for the benefit of third parties:

  to switch from secure boot UEFI Legacy Boot on Elitedesk 800 G2 (and others with the same firmware):

  F10-configuration of the BIOS

  'Advanced' - 'secure boot configuration', set 'key to secure clear boot '.

  Save & Reboot

  machine you ask for a code, enter it and restart.

  F10-configuration of the BIOS

  "Advanced" - "" secure boot configuration ".

  Select 'enable legacy support '.

  Save & Reboot

  F10-configuration of the BIOS

  Startup options: Disable 'UEFI boot order' and activate/configure "boot order of inheritance.

  Save & Reboot

  Yes, 4 reboots are required unless there is a quicker way that I don't know.

• 800 Mini G2 EliteDesk: Dual 4K displays with EliteDesk 800 Mini G2?

  I have an EliteDesk 800 Mini G2 with the i5 - 6500T CPU and integrated graphics card Intel 530. There are also two DisplayPort connectors. As the title says, I tried to find out if the device supports two monitors 4K 3840 x 2160 @ 60 MHz. The specs seem to suggest that it would work. I'm confirming without having 2 K 4 monitors on site. Anyone know or have experience with a configuration like that?

  The i5 - 6500t supports up to 3 screens to 4096 x 2304 @60 Hz

  http://Ark.Intel.com/products/88183/Intel-Core-i5-6500T-processor-6M-cache-up-to-3_10-GHz

  Implementation of multiple 4K displays with your EliteDesk 800 Mini G2 will work. Your EliteDesk Mini supports up to three displays to the right of the box. I suggest using the displayport output ports.

  http://www.Intel.com/content/www/us/en/support/graphics-drivers/000005580.html