HP ENVY 100 and IPhone 4S

Similar Questions

• ENVY 100 and OS 10.7.1

  Hi all

  I have installed all updates for HP envy 100 and connected to the internet / wireless printing and scanning of Mac OS 10.7.1 successfully.  However when trying to scan from the touchscreen scanner, destined for 'Computer' selected none of the exposure of the Mac as connected upward (all computers connected to the list are empty). Is there a way to force the printer/Scanner to 'find' the computer?

  I can scan wireless since the mac via the application on the desktop, but not from the touchscreen scanner.  Any ideas would be greatly appreciated.

  Thank you

  RMK

  Try to download and install the driver from the link below, then check the scanning:

  http://FTP.HP.com/pub/softlib/software12/COL40170/MP-97934-1/HP_Lion_Ink_SW_v12.13.19.dmg

• ENVY 100 and osx 10.6.

  Scanner creates only a black page. Envy is connected to the iMac via usb cable. Document & printing photo is excellent. It will scan just not. Uninstalled all HP software. Reinstalled from original disk. Upgrade software and all the firmware via the HP Web site. No improvement. Have you tried the utility icon analysis HP & icon Scan 3. No change.

  Impossible to use peripheral façade to copy... new page only black.

  I've seen this problem in the forum but found no solution. Are we all make the same mistake somewhere? Thank you!

  Here's how to contact HP technical support: www.hp.com/go/totalcare (click on printers & monitors, there is a phone number on the resulting page).

• I have a hp envy 100 and have problems printing black and white. Print everything in b & w?

  Could not find the place to change the settings, I'm under windows 97

  Hello

  Used to print application, click file > print.

  Then click on properties / preferences to access the Print Options dialog box.

  Click the Advanced button and set printing in grayscale option as black ink only.

  Kind regards

  Shlomi

• ENVY 100 all-in-one: Envy 100 printer all-in-one - will not glossy paper 250 gsm

  Difficulties that the printer will not accept 250 gsm paper past the printhead.

  Followed him orders for cleaning rollers, reset by disconnecting the power and brought etc. cartridges.

  I note others have had the same problem which seems to have been set by a semi of hardware reset. How can I get the required for the semi reset procedure?

  Thanks in advance.

  Welcome to the @noxasforums.

  I saw your post about your Envy 100 not pulling by glossy paper 250 gsm and wanted to answer you! I checked the specs for the Envy 100 and as you can see below, the printer should take in if you use a format supported below. Maybe you can try the steps from the link I posted for you. I think the cleaning rollers should help. You can also try to select different types of paper to see if one works better than the other.

  Let me know what happens!

  • HP ENVY 100 (D410) and 110 (D411) e-all-in-One Printer Series - 'in paper' Error Message displayed the ENVY and the printer isn't looking upwards or the paper feed

  Tip: Make sure that the printer is plugged directly into a wall jack, avoiding bars power and surge protectors. This ensures that the printer is full on.

  

  Testify of my answer by pressing the thumb in the air below and hit the "accept as Solution" button, if I have you helped a resolution!

  Good luck!

• HP Envy 100 v, 110 v 114

  Hello

  First of all I'm new here so please forgive me if this is in the wrong forum.

  Basically, I'm after a new wireless printer, I have been looking at the HP Envy 114 because of its wireless & Airprint capability.

  I want this camera in black, they have on the Apple store online for £220.

  However, I found the model Envy 100 £125, nine - this seems to be a huge price difference for (that I can see) not a lot of difference in functionality.

  Is not wrong in thinking that the only difference between the 100 and 114 is double-sided printing and installation of eFax?

  If these are the only two differences between these two models, so I may as well go with the model 100 and save me about £100.

  Thanks in advance for any help!

  Hello

  Welcome to the forum and thanks for your post!

  From what I can tell, the differences between the Envy 100 and 114 are minimal, as you say.

  The 114 has slightly better black print quality (1200 dpi vs 600 dpi) but the quality of the colors is the same for both products.  The 114 will also be printing/scanning slightly faster than the 100.  The 114 eFax, but from what I can tell the Envy 100 print double-sided and feature (here's a link to the data sheet/sheet: http://www.hp.com/hpinfo/newsroom/press_kits/2010/InnovationSummit/Envy_100_Datasheet.pdf).

  And, here's the datasheet for the 114.  http://www.shopping.HP.com/shopping/PDF/cq811a.PDF

  Looks like the 100 will be very good to meet your needs.

  Hope that helps!

• "Problem connecting to the Server Web Services." - HP Envy 100

  Hello world

  I wonder if anyone has the same problem as me. I just got a HP Envy 100 and went through the process of setting up without problem. The printer is connected via Wi - Fi for wireless network, I can ping the printer from my Mac successfully and I can print within the network without problem.

  However, regarding ePrint and Web features, it seems that nothing really works. I can't even turn on Web services, I always get the message "problem connecting to the Web Services server.

  I tried the following:

  -Restart the router and printer

  -Change the manual IP address and manually set the DNS server

  -Reapply automatic IP and set the Google DNS (8.8.8.8 and 8.8.4.4) servers

  .. .with no chance whatsoever. If this is a problem with the firmware (from what I understood, I do not have the latest firmware, but I can't ask her update, because it requires, you guessed it, a connection on the server of web services, that is the whole of the problem.)

  Anyone else having the problem? Everyone had it and fixed it? Is this just a temporary problem with HP servers?

  Thanks in advance!

  Hey, for me it works as well, and I didn't, just retried that I had tried before and it connected to the Web Services without problem.

  So I think it's safe to say that the original problem in this topic only lied to a HP Server-side problem. Not cool it took so long for them to solve and in particular the fact that we did not really have feedback appropriate about the problem.

  Anyway, I solved (for now, at least).

• ENVY 100 scans documents and photos cultures, regardless of where they are placed.

  ENVY 100 scans of documents/photos cultures. Preview is fine, but not the final result. With the help of Mac OS 10.7.5.

  This scanner has always cropped my images or documents, even if then I see very well in the preview. Right now I'm scanning my passport. I have it lined up against the side (as it shows on the drawing on the scanner) and I see the entire image on the preview. However, when it comes to the final image, I get a version cropped my passport.

  Where can I go to fix this?

  Hello
  The default analysis workflows configured to scan photo 6 x 4 in. make sure you change the scanning settings to not crop the area swept as follows:

  1 open the HP utility and select your device.
  2. based on Scan Settings open the "Scan to Computer".
  3. click on the tab "scan tasks.
  4. Select the shortcut Scan allows to analyze, and then click on edit.
  5. in the section of scanning from an HP device, click the blue triangle or button view details to expand the menu.
  6. in the expanded menu now, open the drop down next to cultures in and asA4 or None value.
  7. click OK and try to scan.

  If you get an error when trying to change shortcut scan patch installation, and then follow the steps above to the following:

  http://FTP.HP.com/pub/softlib/software12/COL41827/MP-101648-1/HP_Scan_for_Mac_OS_X_10.7_Update.dmg

  Kind regards
  Shlomi

• Why Multicolor vertical lines appear in digital images (preview and printed) using Envy 100?

  I do not often use of Scan function.  When I tried to copy an element, a few weeks ago, I had a vertical mulicolored Strip approximately 3/8 ' wide down right side about 1' of the edge.  Band appears in the copy print and preview before printing.  Unplug unit does not resolve the problem.  Hardware problem?  The user of the scanner cover is replaceable?  ENVY 100 (D410a series, p/n CN517A) is less than 2 years old, but more under warranty.

  Perhaps, it looks like this

  Spoiler (Highlight to read)

  

• Will my macbook pro and iphone 5 s charge a 220 volt in Thailand?

  I bought a MacBook Pro in 2011 and I have an iPhone 5 s. I'll be living in Thailand for work and need to know whether or not I need to purchase adapters/converters to recharge my appliances safely.

  If you have a good cable and adapter to the power outlet, you should be fine.   Products Apple generally work with any voltage between 100 and 250 v.

• IM moving to the United States, to the United Kingdom, and have a 1 year old Office Mac, Ipad 2 and iphone 5 s, I need new Chargers/cords?

  IM moving to the United States, to the United Kingdom, and have a 1 year old Office Mac, Ipad 2 and iphone 5 s, I need new Chargers/cords?

  You need not buy new Chargers.

  You need to plug adapter American Electric type.

  http://www.worldstandards.EU/electricity/plugs-and-Sockets/

  All computers/Apple iOS devices come with voltage: 100-240 v AC.

• ENVY 100 D410a: Printer loses connectivity after mode "Eve"

  I have 2 printers, OfficeJet 5746 and Envy 100 D410a and both meet the same problem.  They work very well, then after having been slowed, printing "printer not connected" is displayed.  I did the exercises to unplug the router, remove printers from the list, I checked the ip address and they start with 10.  I have reset the printer.  I went alone on the list of printers (envy) and the problem still persists.  Please, what can I do?

  Use the following link to create yourself a file number.
  Step 1. Open the link: http://support.hp.com/us-en/contact-hp
  Step 2. Enter the product number or select Auto detection (use officejet info)
  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.
  Step 4. Scroll down and click on options contact HP - click Get phone number
  File number and phone number are displayed.

• DAMAGE SMARTE BATTERY AND IPHONE BATTERY CASE

  Don't damage case smart battery the battery of the iPhone because it's over it load when both are a load of 100%?

  No, an iPhone or ANY device powered by batteries Apple, are increasingly unable to load. The devices themselves regulate their own charge cycles and will stop when the battery's load capacity. They can no longer charge, period.

  ALL Apple products conform to the standards of SMART international lithium battery explicitly include the requirement that all these devices have built in protection fees.

  When the battery of the iPhone itself is 100% he treats the case of battery even as it would any other external power source. Loading stops and the unit runs the external power source.  If the box is connected to a power adapter, then it stops too much load to 100% and must simply acts as a passage of connection for external power to the iPhone.

• HP-Envy 100 D410a just shows (INITIALIZE) is on the screen!

  HP-Envy 100 D410a was printing then stopped. When I turned it back on, just shows the printer (INITIALIZE) is on the screen! It was after I left the power for hours. Can't do anything to the screen.  My firmware Version is: SLM1CN1039FR

  Hello

  If your printer is connected wireless, make sure temporary connect the USB device, and then follow the patch below:

  Windows:

  http://ftp.HP.com/pub/softlib/software12/COL37748/MP-92513-1/D410Envy_FWUpdate_4684_HPCOM_x86_v2.exe

  Macintosh:

  http://FTP.HP.com/pub/softlib/software12/COL37909/MP-92884-2/HP_Firmware_Updater.dmg

  Please let me know if this is useful,

  Shlomi

• Unable to get web services reactivated on Envy 100 D410

  My envy 100 D410a was once working with ePrint, but has not been used for a while.  I've recently switched to connected HP and had to re - register the printer.  The news to save the printer would not print.

  After trying a few times, I removed the web services and then tried to turn it back on, but every time I get the message "problem connecting to the web services server.

  I have the Group of experts through the troubleshooting to restart the printer, restart the router, nothing helps.  I have currently set an IP address manually and can print wireless via a laptop, but not ePrint and no web service.

  I tried to configure the servers manual DNS 8.8.8.8 and 8.8.4.4 (via the printer IP address URL), but whenever I try, I get an error:

  An error has occurred. (wipv4Page-400)
  Click 'OK' to go back

  The current firmware is: SLM1CN1039HR.

  SOLVED!   This can be closed.  I did a factory reset, but not on the tab network/section.  Once I did this and restarted the printer, web services could be reactivated.  I can now access the printer via HPEPrint.