HP Envy 15 t Touch - J1H35AV: USB Thumb Drive capacity

Similar Questions

• USB Thumb Drive (UHYBS-064GH) format/write protection fault

  Hello

  Hoping for help.

  Bought a 64 b USB Thumb Drive (UHYBS-064GH), a private seller, but the point is brand new in packaging.

  When I tried to copy files through him, he maxed out at comments 45Gig and seems to have caused a clerical error. I was able to remove the majority of the cases, however on 5gig of them would not remove (in that they seem to have removed, until you updated).

  To counter this, I tried to "quick format", the drive (using Windows XP SP3), but the disc is write protected and I am unable to remove it.

  Spoke to a friend who told me that I should try a low-level format, which tried & it seemed to work, however when I insert the USB system indicates that the drive is not formatted & I would like to format. When you click Yes, I get the error 'write protected '.

  Was the question of the google machine & even tried to change registry settings, but also failed.

  So I hope someone out there has a solution for me (which does not include a big hammer & some anger management)...?

  Would it be possible that this USB drive is defective?
  In my opinion, you should contact the merchant and must replace it with another.

• Can copy a computer usb thumb drive "loss of property.

  Hello:

  Try to copy files mp3 music from my computer (Windows Vista) on USB.  Some MP3 files, run clean and some have not.

  Loss of property:

  The file has properties that can't be copied to the new location.

  Are you sure you want to copy this file without its properties.

  Any help, thanks

  Are you sure you want to copy this file without its properties.

  Yes, you are safe.  An MP3 file without tips 'digital rights' has no particular "Properties".  Background: NTFS (the file system normally used for Windows operating systems) can store properties in other data stream for the file.  FAT32 and exFAT (file systems normally used for orders of USB thumb) cannot do.  As suggested by Jessen, you could format your key USB in NTFS, but which could also reduce its on-line time, and you are not supposed to remove NTFS devices without preparation.

  If you have downloaded MP3 files on your hard disk on some Web site they have a property of the "internet zone", resulting in a request for confirmation if you want to open (= room) the file.  Once you authorized that the info box is removed.  You can also right click on the file, click Properties, and allow future access.  Or you can just copy the file FAT32 or exFAT without ownership of the area.

• HP Envy Touchsmart E0K45UAR: Envy of HP Touchsmart E0K45UAR USB Controller Driver

  Hello

  Computer details:

  HP Envy Touchsmart E0K45UAR

  8.1 Windows Professional x 64

  I have a USB controller, who decided to uninstall itself this morning and I'm unable to get it working again. This was noted during the user's usb keyboard stops working, but the keyboard and the standard touchpad work very well. I can't get any other USB periphials to work on this computer.

  The Windows Device Manager shows "other devices / Universal Serial Bus (USB) Controller" with a yellow exclamation point icon.

  Hardware ID:

  PCI\VEN_8086 & DEV_9C31 & SUBSYS_190E103C & REV_04
  PCI\VEN_8086 & DEV_9C31 & SUBSYS_190E103C
  PCI\VEN_8086 & DEV_9C31 & CC_0C0330
  PCI\VEN_8086 & DEV_9C31 & CC_0C03

  I tried to remove the controller device manager USB, then picking up Windows to automatically reinstall USB controller drivers, it did not help.

  Logs of events coming from the activities of this morning show the following:

  configured device 20150617_070336 (Null)
  Device PCI VEN_8086 & DEV_9C31 & SUBSYS_190E103C & REV_04\3 & 11583659 & 0 & A0 has been configured.

  Driver name: null
  The class GUID: {00000000-0000-0000-0000-000000000000}
  Driver date:
  Driver version:
  Driver provider:
  Section of the driver:
  Rank of pilot: 0x0
  Matching device ID:
  Advanced driver:
  Update of the device: true

  20150617_074754 deleted device
  Device PCI VEN_8086 & DEV_9C31 & SUBSYS_190E103C & REV_04\3 & 11583659 & 0 & A0 has been removed.

  The class GUID: {00000000-0000-0000-0000-000000000000}

  configured device 20150617_074855 (Null)
  Device PCI VEN_8086 & DEV_9C31 & SUBSYS_190E103C & REV_04\3 & 11583659 & 0 & A0 has been configured.

  Driver name: null
  The class GUID: {00000000-0000-0000-0000-000000000000}
  Driver date:
  Driver version:
  Driver provider:
  Section of the driver:
  Rank of pilot: 0x0
  Matching device ID:
  Advanced driver:
  Update of the device: false

  I'm sure that there is a problem with the drivers, but I can't find the USB drivers on the HP support page for this model of computer downloads.

  Thanks in advance for any help.

  So I just ended up doing a restore system since a couple of days and I have my USB controller online.

  No idea of what was actually wrong with it.

• Satellite R10 - ACPI BIOS Version 1.30 cannot boot from USB Thumb Drive

  I'm trying to recreate the image on this laptop, but the script I use is on a USB key, how can I boot from this device?

  >... the script I use is on a USB
  Sorry for the question but what do you mean with script?
  You have created recovery USB support?

• iTunes to USB Thumb Drive in the car game

  Good evening to all!

  I don't see my specific problem are answered one of the many discussions on this subject.

  Long and short of my problem is I am trying to copy my iTunes together (some 30 GB) library on a USB key in order to use it in the car and stop overpaying each year for a larger iPhone.

  I know exactly what I need to copy - i.e. records specific album in iTunes Media / Music folder. This seems to be the only way it is displayed correctly on my car - with genres / artists / albums etc. Any other attempt to copy - or as a straight line and do drag on iTunes, which is a copy of the iTunes all folder Media does not and shows only a list of MP3s no sortable (30,000 of them).

  The problem I have is that iTunes saves the Media folder by artist, then album (other than the folder of the complication) and there are more than 500 artists, which means that I have to drag and drop each individual album at the command of an inch of each individual artist record - which is something that I just can't bring myself to do.

  Can anyone suggest a quick way to copy several subfolders or displays only records the album for me copy?

  Thank you very much

  I use this: https://itunes.apple.com/us/app/export-for-itunes/id880764359?mt=12

  This will convert AAC files unprotected MP3 if necessary and export whatever you choose, keep a nice folder structure for the albums. It will also export playlists if the radio in your car permits.

  I keep several 16 GB USB drives in the car with various sets of music that I swap in according to the mood.

  It is not free, but for me, it was worth the money just to save me hours of work.

• path is too deep message when copying files to the hard disk to usb thumb drive

  am runnjing Windows professional xp and have recently begun to meet with messages saying 'Filename' path is too deep, trying to move files from my hard drive to a USB key. I realize there is a limit on the length of path, I think that 250 characters, but I'm no where near this limit. Move files with long length of path names and file with length of shortest path names are not.

  It seems that less than 100K spreadsheets okay and spreadsheets more than 100K are not. I think my problem was with Open Office but I also struggle with the larger PDF files.

  If I one of these "problem files", open ones I can't move or copy and try to save them on my drive of thimb, the system hangs for several minutes and sometimes tells me that I started recording order with an invalid character.

  I see others have problems similar encounteres on several internet forums. Is the cause of this known? Is there a fix I can install to remove the problem?

  Try RichCopy.

  http://TechNet.Microsoft.com/en-CA/magazine/2009.04.UtilitySpotlight.aspx

  Tom Ferguson

• USB Flash drive does not work with Windows 7 Pro 64-bit

  I have several USB thumb drives, some of them do not work when I plug them in while others work very well. By experimenting, I reduced the problem with the 64-bit Version Windows. All of these USB keys works well in my other computers that have 32-bit installed and also even computer with the 32-bit version installed on different hard drive. All of these thumdrives are detected immediately and works without a problem. The 64-bit version, I have uninstalles and reinstalled readers, drivers updated for readers and controllers USB chipset, reasigning letter drive without a resolution of the problem.

  It is interesting to know that this problem only occurs with some discs that I (like Ativa 4 GB, 4 GB generic and Verbatim 4 GB). While I discovered that you can do all the nonworking day thumdrives work once if you shutdown computer and plug the thumdrive into the USB port and the computer to boot, boot time is longer than usual and when it is operational in 30 to 45 seconds drive appears in the list of devices and you can read, write and format normally without any problem to experiment. When you pull chase him and reconnect to USB port after 10 seconds same problem appears aggai. First of all, you get the message that the disk must be formatted and if you try to format you will get a message that windows cannot format the drive. If you try to access the drive, you get message that Drive is not accessible. If I take this player and plug it from 32-bit without problem, you see all the files in the drive and are able to read the writing and the format is normally.

  I'd appreciate if I am able to get an answer as a way to solve the problem.

  Pavan

  When you disconnected the battery of the laptop, you did, be sure to press and hold the power button for about 10 seconds?  This causes the rest of completely discharge power.

  This tip came in practice more than once in my experience.   ^_^

• TouchSmart HP Envy 17-j017cl touch screen click on screen by itself

  64-bit Windows 8
  Product number: E9G80UA

  I recently bought about 4 months ago and it's great for a little while. But recently he would make this annoying glitch. The screen would act as if I'm pressing the screen somewhere in the middle of it and selecting whatever it is within its range. This may seem not so bad by the sounds of it, but if you play a video or a website with links in this area it will click on a link or stop/play videos. It is very annoying!

  Troubleshooting: at first I thought that it would be my touchpad, so I made sure that I didn't to it during these periods. But it would still do so even if I'm not in contact with the laptop. So if I use only my wireless mouse to go through Web pages or anything else, he would still do the ghost by clicking.

  I thought then that maybe it's my wireless mouse, so I unplugged the laptop USB receiver and he always does.

  Then I tried to get online with HP technical support and they checked my computer and tried a few things like remove the driver of the touchpad and so on without any results. He finally told me that I have to send it to them for repair (still in warranty). However, I have not the time to send my phone to them for repairs.

  My last thought was to turn off the touch screen. What I did by going to Device Manager and by disabling one of the HIDDEN options. I've had several, so I had to try each of them since none were marked as the touch screen, but only as a HID device. It has worked so far and he has not clicked anywhere yet.

  My question is, is anyone know what I need to do to correct the problem? I thought to update the driver, but I can't find it on the HP site and when I try to update the driver through Device Manager it says he has the best driver available, which most of the time is BS. I guess I just need to know where I can find the right driver for the touch screen.

  Hi Spoon1901,

  Thank you for visiting the Forums HP's Support and welcome. I read your thread on your computer laptop 17-j017cl TouchSmart from HP ENVY and your touch screen, here's a link to a update the system BIOS. It will help improve the screen problems.

  I hope this helps.

  Thank you.

• Want to 15 t Touch: question M.2 SSD for HP Envy 15 t Touch (model 15 t-ae100)

  I ordered the HP Envy 15 t Touch (model 15 t-ae100) with the i7 processors and 4 GB of memory graphic discreet. The Maintenance and Service Guide accurate that there is a slot available for one SSD m2.  From what I can tell, it's a SATA 3 (not mSATA or PCIe) slot that will be a 2280 SSD card.  Three questions:

  1. where did the m2 slot located on the motherboard?  Adjacent to the wireless network adapter?

  2. is there a screw included on the motherboard for the SSD m2 card?

  3. any compatibility likely questions if I get the EVO of 850 Samsung 500 GB m2 (MZ-N5E500BW)?

  Thank you very much

  Tom

  Hello @space_thread,

  Thank you for visiting the HP Forums! A place where you can find solutions for your problems, with the help of the community!

  I stumbled upon your post on the SSD question and wanted to help!

  The m2 slot seems to be located next to the memory Modules.  There is a Phillips PM2.0x3.50 screw that secures the SSD to the system board.  Your product supports the following SSD:

  SSD (m2) drive

  256 GB - 812708-001

  128 GB, 2280 M2 - 829985-001

  128 GB (Best Buy SKUs) - 820547-001

  Therefore the 500 GB m2 will be not compatible.  I hope this helps.

  Source: HP ENVY Notebook PC Maintenance and Service Guide (Chapter 6, Page 42-43).

  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution' , this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• HP Envy 17 t: what size usb drive is necessary for the recovery of HP Envy 17 t 10 (64-bit) Windows?

  I just installed my HP Envy and wanted to set up a recovery disk.  The USB key must be less than 32gigs, but the example has not been updated for Windows 10 the instructions say.  It shows a recovery screen for a laptop of Win8 with the source of recovery like 17 concerts.   Is there a way to check the requirements for the front to accept the HP one time recovery option.  I have a new 16 GB USB key and wanted to make sure that it is large enough.

  Also do a backup image to DVD?   If so, how many DVDs?   The laptop is new and I added only Chrome and some minor programs.  My data files are always on an external hard drive.

  Hello

  Thanks for posting in the Forum from HP Support.

  To be honest, I don't know what size will be that these recovery files are because they can vary from the version of Windows to another. They can vary from a model.

  In my opinion, 16 GB is probably not enough.

  DVDs are usually 6 (6x4.7 GB = about 28 GB) but this can vary from one model.

  This possibility of imbedding maybe once, there are other ways that you can save your system indefinitely.

  This is a free option included in all windows (creating system image, it's free as included in Vista from the outset).

  http://support.HP.com/us-en/document/c03544793

  However, this option requires (e.g. USB HDD) external HARD disk or DVD. It does not work with USB flash drives.

• HP envy 15-ae130tx: I can add a SSD for my HP envy 15 ae130tx touch screen?

  Can I add a SSD drive in my HP envy 15 ae130tx touch screen? And I can also remove my hard drive?

  Thank you very much!! Sorry for my bad English!

  Yes that's exactly what I say

• Satellite M30X powers off the power when you touch the USB port

  Hello everyone, just registered and it is the first problem:
  As there is no general hardware forum, I post my problem here.

  I got it twice, my laptop
  (Product: Satellite M30X, Version: PSA72E - 008010GR) just went completely off.

  Motherboard:

  NorthBridge: Intel i855GME
  SouthBridge: (ICH4-M) of 82801DBM LPC Interface Bridge
  Motherboard model: Toshiba EAL20

  USB:

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI controller #1-3
  Version: 1.0
  Interface: UHCI
  Frequency: 48 MHz

  82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB 2.0 EHCI controller
  Version: 2.0
  Interface: EHCI

  I have the latest Intel Chipset drivers installed and Windows XP Home SP3 with all updates.

  Once when I hit just the back USB ports with a USB plug, the other time when I unplugged my bluetooth key (climbing din't remove it).
  There was no blue screen or message of any kind, not even in the registry after you start the system again or this fatal system error box when you start after a system error.

  Just a total failure. But it works fine the rest of the time. I also tried to remake the script, but it didn't work.
  I have cleaned with a vacuum cleaner to remove dust and has taken a good look, but saw no difference to the side track.
  Maybe the clamps of the wand to shield a little more out to the contact pins on the rear.

  What bothers me a bit, it's some time ago, I had the laptop one computer my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.
  Still works well. Now for me, that I broke the USB port Insider somehing.
  I could not determine also the loose parts or unfirm at all.

  Y at - it there, diagnostic software that measures the motto of the port or power problems?
  I have a multimeter, fetch short-circuits with it?

  I saw a package of drivers Intel for USB 2.0 over there, but I can't find it on their page, advice?

  Thank you very much for your help, I just wanted to update my RAM and now I am not so shure if my laptop will last the next week.

  Fabian

  Hello

  I put t know any diagnostic software that could analyze this question, I think that a technician of the ASP may be able to provide exactly this question results

  > What bothers me a little is that some time ago, I had the laptop and my knees and I forgot that a memory stick has been connected to the rear. The stick was pushed up and was slightly damaged.

  I think this might be the reason why the laptop stopped while you touch the USB port eventually ports were damaged by using the memory stick, this could cause the laptop off

  However, what we can do is to provide some suggestions and assumptions
  It you want to know why this is happening exactly, then you need to contact a technician laptop for a control.

• HP ENVY Beats all-in-One: usb 3.0 ports do not work

  USB 2.0 hubs work but the 3.0 have never worked. Thumb drives and exterrnal readers do not appear in the file manager. No problem, indicated in the Device Manager.

  Thank you for your help.

  After searching around, I found new info: F2 at startup - BIOS - HP has a tool to check if different parts of the computer are working correctly. (Officially), I learned that the usb ports two 3.0 do not work (despite Device Manager, telling all the devices work properly). I received a "failure code" and a phone number to call. Technical support has confirmed that the failure code indicated the 3.0 ports do not work, and for $215 they can repair (price including shipping Fedex).

  I see if someone locally replace ports. Not sure that 3.0 ports are worth anywhere from $215. After all, the computer works just fine as it is. It's just annoying, they have never worked, that it took so long to finally find a solution, and that the warranty has expired.

• laptop Envy 17 17-j034ca: can not detect the usb flash drives

  Hi, I recently installed windows 7 64 bit on my computer laptop envy 17 17-j034ca. Then, I managed to install all the drivers but it still doesn't detect usb flash drives and I tried to install from the web site of HP and my config but it still does not work

  Please help me

  

  It's ok my sound suddenly computer detects the flash drives normally